Search Documents

By W. N. Best

(San Francisco Meeting, September, 1915) INTRODUCTION CRUDE oil attracted attention because of its excellence as a fuel for open-hearth furnaces; for making crucible steel and brass; for melting copper, lead, tin, zinc, nickel, silver, malleable iron, gray iron; and for the production of steam in all sizes and types of boilers. For heating furnaces, mold-drying ovens, core ovens, ore roasters, calciners, hot-air furnaces, sand drying, asphalt road work, etc., its superiority over other fuels is due to the fact that the heat is at all times under perfect control, so that a constant temperature may be attained and maintained at the will of the operator. This means a maximum amount and uniform quality of work. Crude oil is of two kinds, paraffine base and asphaltum base, and varies from 11 to 46 gravity Baumé. The light-gravity oil does not require heating before use; but oil of less than 20 gravity Baumé should be heated to just below its vaporizing point, in order to reduce its viscosity and to obtain the highest efficiency of combustion. Heavy California oil vaporizes at 230°'F., Mexican crude oil at from 175° to 210° F., and Beaumont, Texas, oil at 142° F. Fuel oil vaporizes at 130° F.

Jan 8, 1915

By E. S. Fisher

GRAIN coarsening implies a discontinuous type of grain growth during which a few grains in a fine grained recrystallized matrix grow to large grain sizes at the expense of the matrix. Studies of this phenomenon in various metals1,2 indicate that grain coarsening may result when continuous grain growth in a fine grained matrix is inhibited by either a dispersion of very fine inclusions or by a strong texture. In the former case a period of annealing time exists prior to grain coarsening during which grain growth inhibition is gradually de- creased by dissolution or coalescence of the dispersed inclusions. This mechanism can be made to occur in uranium during anneals at high a phase temperatures. ' A study of some of the factors influencing the kinetics of grain coarsening and the coarse grain sizes in a uranium has led to a method for preparing a uranium single crystals. Previously such single crystals containing considerable substructure were prepared at this laboratory by a phase change method, similar to that described by Cahn.3 Attempts to prepare more perfect single crystals by strain-anneal techniques were unsuccessful. Cahn3- as reported his attempts to apply such techniques to uranium. He proposed that the failure of strain-anneal techniques is basically due to the many twins which

Jan 1, 1958

By C. S. Matthews, H. C. Lefkovits

The performance of depletion-type reservoirs at the stage in which the gas is at such low pressure that gravity is essentially the sole driving force has been investigated both theoretically and by use of scaled models. A simple theory is developed which completely explains the scaled model experiments. It also agrees with some field data. When the range of production rates to be considered is less than 25, the theory predicts that the production rate decline curve for homogeneous reservoirs in which there is a free surface will be of the hyperbolic type with n = 2: The theory gives a physical significance to the parameter y. INTRODUCTION This investigation was undertaken to determine a method for prediction of performance of reservoirs where gravity is the sole driving agent. Depletion-type reservoirs fall into this category after the pressure has fallen to some low value. Some examples of this type are found at Healdton ('Oklahoma), Oklahoma City (Oklahoma), Midway-Sunset (California), and East Coalinga (California). Generally the production rate per unit thickness is quite low in such reservoirs, with the conse- quence that this stage is sometimes called the stripper stage. However, per well production rates may be of the order of 50 B/D because of the considerable sand thickness open in some of the reservoirs. In the past, predictions of behavior of such reservoirs have been based on empirical extrapolation of the rate of production to the economic limit. Difficulties arise when new wells are drilled in the field or when production is artificially curtailed, since in such cases the decline rate of individual wells or leases changes and no clear trend can be detected. It was hoped that the present study would lead to improved methods for evaluation of such reservoirs. The study was initiated by building a scaled model for a particular field and by running a number of experiments on this model. Later a simple theory was developed which explained the laboratory results completely. The theory led, as shown below, to a hyperbolic-type decline equation which had been used previously' in a completely empirical manner. THEORY The General Case The problem to be treated here is the following: We are given a homogeneous cylindrical porous reservoir with exterior radius r, wellbore radius r., and height h,, containing, from the bottom up to a height hit oil, some gas, and interstitial water (see Fig. 1 A). The portion of the reservoir between K, and h, is filled with gas at low pressure, with residual oil, and with interstitial water. If at a time t = 0, the level of the oil in the wellbore is lowered to a height h,, what is the production rate from the reservoir at a time to The configuration within the reservoir at some instant

Jan 1, 1957

By Yap Chu-Phay

IN the previous paper, the writer showed how, on the basis of thermodynamic reasoning, it seems probable that when true equilibrium conditions obtain, carbon exists as Fe3C in the liquid state and as elementary carbon in the solid state (7 Fe), in which case the solidus would be a straight line from 0.18 to 1.70 per cent. carbon (Fig. 1). In the same paper he concluded that the solidus obtained by Honda 'and his co-workers1 probably does not represent the same conditions, insuring a complete equilibrium. Except for a downward temperature displacement, the solidus obtained by Gutowsky,2 using the Heycock and Neville method, practically coincides with Honda's solidus as shown in Fig. 1. The writer at first thought that perhaps in some way Gutowsky's thermocouple was improperly calibrated for high-temperature measurements, as his liquidus was also much lower than those obtained by Carpenter and Keeling3 and by Ruer and Goerens.4 However, the eutectic temperature obtained by Gutowsky agrees with the generally accepted value of 1130° C., so that the validity of the inference regarding improper temperature calibrations is to be strongly doubted. In Fig. 1, Gutowsky's solidus is shown both in the original and in the corrected form. In the latter, a correction of 29.2° C. is made for all temperatures above 1416° C. in accordance with-

Jan 1, 1931

By Alden B. Grenninger

The time-honored description of the growth of metal crystals to form polycrystalline aggregates is one in which two important steps are considered: (1) nucleation, and (2) dendritic growth, each dendrite starting from its individual nucleus and resulting (upon slow cooling, assuming no solid phase changes) in a macrograin. This picture of the process of crystallization is incomplete, and it is with the hope of enlarging upon it that the following summary and correlation of experimental results are given. Mosaic Structure For an exact definition of the mosaic structure of metal crystals—if, indeed, one can be found that will hold for all metals—one must await the results of much experimental work in this field. The writer's investigations have been confined almost entirely to copper and a few of its alloys. The following terms are proposed, and will be used in this report: Macromosaic Structure1.—Large-scale mosaic structure; more specifically, mosaic structure of a scale large enough to produce splitting of Laue spots on back-reflection Laue X-ray patterns2. The deviation from exact parallelism of neighboring macromosaics varies from a few minutes to a few degrees3. Just as there are no exact dimension limits for macrograins, so the dimensions of a macromosaic vary considerably. Macromosaic structure may often be seen on copper single crystals if they are examined carefully with critical illumination4. However, back-

Jan 1, 1936

By James B. Duke, Ernest W. Greene

An idea of what is meant by "Ultrafine Minerals Or Slimes" as used in the title can be had by an examination of Fig. I. Particle size distributions are presented for a crude kaolin clay, a coarse fraction and a fine fraction. The crude kaolin as mined was blunged with water, degritted through a 325-mesh Tyler screen, and dispersed with sodium silicate. The dispersed crude was then centrifuged in the laboratory into the coarse and fine fractions shown in the figure. The distribution curves were obtained by the well known sedimentation technique of Casagrande' using a long arm centrifuge to obtain equivalent spherical diameters down to 0.2 microns on the finer fraction. Fig. 1 shows the coarse fraction kaolin to be 50% finer than 3 microns, while the crude kaolin is 50% finer than 1.4 microns, and the fine fraction 50% finer than 0.6 microns. For comparison 53 microns on the horizontal scale would represent Stokesian diameters which would just pass a 325- mesh Tyler screen, taking into consideration the Andreasen sieve correction factor of 1.22 X the screen opening.' Another helpful comparison is the surface areas, which in square meters per gram, are 0.044 for 53 micron particles, 0.77 for 3 microns, 1.65 for 1.4 microns, and 5.0 for 0.46 micron particles. Fig. 2 is an electron micrograph of a similar fine fraction kaolin showing the hexagonal plate- like particle shapes.

Jan 10, 1962

By J. B. Umpleby

The subject of reservoir energy and its efficient utilization has been well explored in many papers. The present effort, therefore, is limited to a summary of existing information combined with an emphasis of the probability that the relative importance of controlling factors will change with advancing knowledge. Consequently the necessity for flexibility in laws and regulations, inherent in the problem, is emphasized. Definitions Many terms have been widely used in the literature without having been specifically defined. For example, confusion exists in the use of ((reservoir energy" and "gas energy." The latter is much more limited in meaning than the former. Other terms have been variously used. Consequently, I shall preface my remarks with definitions of a few of the more pertinent terms. Reservoir energy is that force or forces, active or potential, that is native to the reservoir and has the power to move oil through the reservoir rock. The energy may result from expanding gas, from hydrostatic head, from the weight of overburden, or from any other source. Gas energy is the expansive power of gas when pressure is reduced. It is one type of reservoir energy. An oil reservoir is that part of a geologic formation or formations in which oil occurs in commercial quantities wholly surrounded by nonproductive rock. The essence of this definition is effective separation rather than remoteness and under it oil reservoirs may be superimposed in the same oil pool. Conservation of reservoir energy means primarily its maximum use in the production of oil. Unit operation is a plan of development and production, which embraces an entire oil reservoir under a unity of engineering control. It is distinct from unitization, which has to do with arrangements of organization and equities to make unit operation possible in areas of divided ownership.

Jan 1, 1934

By H. C. Jennison

Two distinct types of defects occur at times in copper wire as a result of the use of dies of improper design or undesirable wire-drawing practice. The conditions under which these defects may be produced, as well as precautions to be taken in order to prevent them, have been known to The American Brass Co. for many years. The quality of the copper wire bars and rods has too often and unjustly been held responsible for these particular defects and it is to correct any such belief that this paper is presented. An extremely high quality of electrolytic copper has been supplied to the trade by all refineries for the last 20 years at least. The purity of the copper would average well above 99.900 per cent. The casting of the wire bars has been handled in a generally satisfactory manner. The bars have been cast sound, with a flat to slightly crowning set and have been free from sloppy edges, cold sets, etc. In other words, the wire bars have met A. S. T. M. specifications and have been generally satisfactory. For the most part, they have been everything that could be desired from a quality standpoint yet most of the wire mills in this country and in Europe have at times held the quality of the copper responsible for the two types of defects described in this paper. As a matter of fact, these defects are produced entirely in the wire mills. The author has visited many of the large wire mills in the United States and in Europe to investigate these defects. In some cases the trouble has been so serious that the wire mill has ceased operations. At times the wire mills are reluctant to believe that they are responsible for the defective product. The effect of die design, wire-drawing practice, etc., upon the quality of copper wire has received' little study on the part of wire mills, particularly those that have commenced operations in the last few years.

Jan 1, 1930

By Carl J. McHargue

Rods of 99.99 + pct Al which had initial orientatzons of <001>, <118>, <115>, <111>, and random were swaged at room temperature. Changes in orientation as a function of deformation were studied on axis distribution charts. The <001> orientation appeared to be relatively stable due to the inhomogeneity of the deformation process. near the <100> zone were quickly reoriented towards <001>. Orientations on the <110> zone between <118> and <115> appeared to be stable to reductions of about 50 pct, then were reoriented toward <001>. At very high reductzotzs. movement away from the <111> orientation was observed. the requirement that a circular cross section be maintained. In addition to these mechanical factors, there are grain-boundary effects in poly crystalline materials which are not yet understood. Hartmann and Macherauch conclude, for example, that multiple slip occurs for all orientations in fine-grained aluminum and copper and that the choice of operative slip systems has no simple relationship to orientation.? Many investigators have attempted to avoid problems of interpretation caused by an initial texture by treating the starting material to obtain as ran- IT has been generally accepted that the deformation texture obtained at high reductions, e.g. 90 pct, will not be noticeably affected by a prior texture; whereas, that obtained at reductions of 40 to 50 pct may be significantly influenced by the specimen history.&apos; Some recent studies, however, have been interpreted as showing that an initial texture strongly influenced the deformation textures in rods at reductions greater than 90 pct. Freda and Cullity suggested that the <001> texture in a heavily cold-worked copper rod was due to a <001> texture in the original casting. McHargue, Jetter? and Ogle concluded that the <001> component in an aluminum rod extruded at liquid nitrogen temperature was remanent from a <001> texture in the cast extrusion billet.3 Most of the published work on the effect of initial orientation on deformation textures has been for cold-rolled or compressed single crystals,4-6 The primary interest in these studies was to examine various orientations with regard to their stability under flow? thus determining the possibility of such orientations being stable end orientations. There appears to be no published studies on the effect of initial orientation on fiber textures in polycrystalline specimens. A recent study, however, is concerned with the reorientation of individual grains in polycrystalline specimens pulled in tension.? Although the reorientation of single crystals loaded in simple tension is well known, the movements in the forming of wires and rods would be expected to be different due to the circular array of radial-compressive stresses exerted by the die walls or the rolls, and to

Jan 1, 1962

E. A. HOLBROOK,*Urbana, Ill.-To those who have followed the development of powdered coal two questions often occur. First, as to the moisture in the coal. In Illinois we recognize that the bituminous coals contain about 12 to 15 per cent. of what we call "contained moisture," that is, the moisture is present in the coal although this may appear absolutely dry and dusty. In addition, the surface moisture may be present in any amount. I would like to ask what is the relative effect of these two forms of moisture upon the work of pulverizing. Does Mr. Collins refer to the contained moisture or to the surface moisture in estimating the degree to which the coal must be dried? H. R. COLLINS.-In the lignite coals, of which this country possesses a great deal and is beginning to develop them to considerable extent, the "contained" or "combined" moisture does not .trouble us; we have no difficulty in reducing lignites to a high degree of fineness. But when dealing with bituminous, sub-bituminous, or semi-bituminous, we, prefer to reduce the combined moisture as well as the hydroscopic moisture as far as possible. We have recently put into operation, at a plant, furnaces and boilers consuming the lignite from northern New Mexico, which contains between 4 and 5 per cent. moisture as we pulverize and burn it. The evaporating efficiencies under the boilers have been so remarkable that we wish to check the results half a dozen times before quoting them. We have also just started two boilers at the Garfield smelter, and have obtained the same high efficiencies.

Jan 11, 1918

By F. T. Lee

Directional dependence of strength and deformation properties of the Mount Waldo granite pluton in southeastern Maine is controlled by joints and microfractures whose orientations are linked to flow- induced alignment of microcline crystals. Longitudinal and cross joints which formed during cooling of the mass, as well as much younger sheeting fractures, are commonly associated with subparallel, discontinuous microfractures. The orthogonality of microfractures (open, closed; filled, unfilled; bubble planes) establishes the ease of splitting of the granite. The easiest splitting direction (rift) is subhorizontal, the second easiest direction (grain) is parallel to the cross joints, while the direction of least easy splitting (hardway) is parallel to the longitudinal joints. Static and dynamic measurements made in the field and laboratory established that structural features are responsible for the marked stiffness anisotropy of the granite. In the central part of the pluton the static Young&apos;s modulus in the north-south direction averages 31.1 GPa, and 20.9 GPa in the east-west direction; the stiffer direction being parallel to the long C-axes of microcline phenocrysts and microfractures as identified in outcrop, core samples, and thin sections. Vertical downhole sonic measurements of dynamic moduli ranging from 2.5 to 16.2 GPa appeared to be anomalously low when compared to the static horizontal values. However, the field sonic values were confirmed by laboratory sonic pulse testing of oriented cores. The field results reflected closely spaced layers of open horizontal microfractures. Those deformation and strength properties that are closely tied to bubble planes, filled microfractures, and microcline orientation could be extrapolated to greater depths with good hope of success.

Jan 1, 1984

By E. T. Turkdogan, J. H. Swisher

The solubility of oxygen in zone-refined iron was determined in the temperature range.from 881" to 1350°C. The solubility in a iron at 881°C ms found to be about 2 to 3 ppm; in y iron, the solubility was found to increase from about 2 to 3 ppm at 950°C to about 25 ppm at 1350°C. The permeability of oxygen in an iron -0.1 pct Al alloy was determined in the y iron range, using an internal oxidation technique. By combining the permeability and solubility data, the diffzisivity of oxygen in y and a iron was calculated. The oxygen diffusivity in solid iron may be s~immarized as follows: 8820 For 6 iron and IN a recent paper, Hepworth, Smith, and Turkdogan1 reported on the solubility, permeability, and diffusivity of oxygen in 6 iron, together with permeability data for oxygen in a iron. In the present investigation, similar measurements were made in the ? phase region. In addition, a solubility measurement was performed in the a phase region to permit calculation of the diffusivity of oxygen in a, iron. References to early work on this subject are given in the previous publication.&apos; EXPERIMENTAL Solubility Measurements. The oxygen solubility was determined by equilibrating cylindrical samples 0.3 in. diam by 14 in. long of zone-refined iron in water vapor-hydrogen gas mixtures. The zone-refined iron was prepared by B. F. Oliver of this laboratory, using an apparatus and technique described elsewhere.2&apos;3 Six zone-melting passes were used to achieve a total impurity level of about 30 ppm. Of this 30 ppm, the combined nickel and cobalt content was about 20 ppm, oxygen was 4 ppm, and all oxidizable impurities less than 1 pprn each. A vertical resistance furnace wound with molybdenum wire was used for the experiments. The temperature was measured before and after each experiment with a Pt/Pt-10 pct Rh thermocouple. In the gas train, flow rates of hydrogen and argon were measured with capillary flow meters, and the resulting mixtures were passed through a column containing 90 pct oxalic acid dihydrate and 10 pct anhydrous oxalic acid to obtain predetermined ratios of H2O to H2. The vapor pressure of H2O above this mixture as a function of temperature is well-known.4 The exit gas was ana- lyzed periodically for H2O, and good agreement (+3 pct) with the calculated composition was obtained. The zone-refined iron specimens were held in the furnace for a sufficient length of time for equilibration, e.g., 18 hr at 1350°C and 1 week at 881°C, then quenched in a brine solution. After removing the surface oxide from the samples by machining, duplicate analyses were obtained by a combined vacuum fusion-infrared method; oxygen analysis was reproducible within 2 ppm. Permeability Measurements. The permeability of oxygen in alloys containing about 0.1 pct A1 was determined by internal oxidation and measurement of the subscale thickness as a function of time. The experimental alloys were prepared by adding aluminum to electrolytic iron (grade 104A plastiron) that had previously been vacuum-carbon deoxidized. The resulting ingots contained about 20 ppm O, 100 pprn C, 40 pprn Si, 50 ppm Mo, 20 ppm P, 20 ppm S, and 20 pprn Zr as the principal impurities. After hot rolling the ingots to 1-in.-thick slabs, specimens were machined from the stock in the form of rectangular plates, 4 by 5 by 2 in. The general procedure for the permeability experiments was the same as those for the solubility measurements. The specimens were cooled in a reducing atmosphere rather than quenched, however, in order to maintain a clean surface for measurement of the sub-scale thickness. This measurement was made on a polished cross section of each specimen, using a microscope with a micrometer stage. The inclusions formed at the lowest temperature 1033°C were too small to be seen with an optical microscope. An electron micrograph showing the size and shape of individual particles is shown in Fig. 1. The dark band in the picture is a boundary between two subgrains. The subscale thickness in these samples was measured with an optical microscope after heavily etching in 2 pct nital, which gave contrast between the subscale and the unoxidized zone.

Jan 1, 1968

By C. E. McCarthy, A. George Stern, Stanley J. Green

THE national interest prompts consideration of any new source of mineral wealth even though the immediate need may be of minor importance. A critical shortage of potash in the United States during the World War of I9I4-I8 stimulated broad development, which established an American potash industry on a basis so sound that this commodity is not even listed as urgent in the present war program. However, this should not minimize its importance, and the need remains, not only for adequate supplies of the usual potash salts (the chloride and the sulphate) but of all potash chemicals. Potassium carbonate (known commercially as pearl ash) has been a high-cost commodity; in consequence, the quantity used by industry has been relatively small. By a combination of fortuitous geographical circumstances, there is opportunity to produce a low-cost potassium carbonate with the possibility that this might become an important source of chemical potash. The following paper considers a recently developed process1 taking advantage of these conditions. WYOMINGITE DEPOSIT For many years it has been known that a deposit of potash-bearing igneous rock known as wyomingite occurs in the southwestern part of Wyoming at Zirkel Mesa, which is 44 miles northeast of the town of Green River (Fig. I). The western escarpment of this deposit is about 3 miles east of the Superior Branch of the Union Pacific Railroad. This mesa alone covers approximately 3300 acres, and the average thickness of the wyomingite flow is 75 ft. It has been estimated2 that about one billion tons of wyomingite occur in this one deposit, all of which can be mined by open quarrying without overburden. In addition, there are several smaller deposits within 10 miles, so that the aggregate wyomingite in the area approaches two billion tons. This is one of the world&apos;s largest sources of leucite, and the only known deposit of its kind in the United States. The wyomingite (which is in the form of a lava flow and numerous small craters), with the mineral leucite as its most important component, has a mineral composition3 of: leucite, 50 per cent; phlogopite, 15; diopside, I2; kataphorite, 15; glass and apatite, 8. The phlogopite is present in visible phenocrysts 1/8 to 1/2 in. in diameter, but the leucite usually is almost microcrystalline and not capable of liberation by grinding. Chemically, the wyomingite has a potash content averaging slightly higher than eleven per cent K20. The potash is mainly in the leucite, but part of it is in the phlogopite and a small amount is in the feldspars that are occasionally seen as undigested occlusions of the granite country rock, through which the leucite-bearing lava intruded, and as sanidine feldspar both in the crystalline and glassy phases of the rock. A typical analysis of the wyomingite from Zirkel Mesa is as follows:

Jan 1, 1944

By Wallace W. Wilson

This DaoerAA calls to attention for the first time, to the writer&apos;s knowledge, a purported recovery of oil by substantially horizontal gas cycling that is considerably in excess of 50 per cent of the oil originally in place. The average angle of dip along the path of travel of the gas is less than one degree of arc. The best recovery by gas cycling previously brought to the writer&apos;s attention1 occurred in the case of the Mile Six Field in Peru, where about 68 per cent of the original oil in place has so far been recovered. In this case, however. the recovery was greatly aided 1)y the high dip angle of about 17.5". An approximate estimate of recovery was made by the method developed by the writer&apos; for the case of the Cook Ranch Field, using an average relative permeability ratio function dictated by past experience with a number of good quality sandstones. A result of about 40 per cent recovery of the original oil in place wa* obtained after the 8.5 pore volumes of cumulative gas cycling undergone by the Cook Ranch Field. Tile writer desires to emphasize what appears to him as the sound engineering practiced at Cook Ranch, and also the care attending the taking of data and the high quality of the calculations made. It is impossible to take issue on factual grounds with any of the conclusions drawn in the paper. It is, however, desired to point out the difficulty of explaining the unexpectedly favorable oil recovery on ordinary theoretical grounds. It would be of interest to know whether relative permeability ratios have been measured on the Cook sand. The operator is inclined to attribute some of the excess benefit to settling of the oil across the bedding planes into the lower part of the sand. It is difficult for the writer to appreciate the importance of such an effect, inasmuch as the concomitant opening of excessive vacated pore space in the upper part of the sand would he expected to cause excessive bypassing of the gas. REFERENCE 1. Welge. H. J.: "A Simplified Method for Computing Oil Recovery by (Gas or Water Drive." Trans. AIME, (1952), 195, 91. AUTHOR&apos;S REPLY TO MR. WELGE Welge has poined out clearly the difficulty of applying material-balance procedures in calculating the Performance of low-pressure, dispersed gas injection operations. There can be no argument that even with the most favorable assumptions of K,/K,, and with cumulative gas cycling in excess of normal expectations, the calculated oil recovery will be considerably less than the 72.5 per cent recovery realized from this project to Jan. 1, 1951. There probably are at least two reasons for the unusually high recovery from this reservoir, the effects of which would be difficult or impossible to calculate by known methods: 1. The operator did not use the same injection wells for the entire operation, and exercised considerable control over producing GOR by changing the locations of injection wells whenever well performance indicated excessive bypassing. Fifty-six wells were used for injection, not over 29 of which were in use simultaneously. This procedure resulted in frequent shifting of the fluid movement patterns in the reservoir and undoubtedly increased the ultimate recovery. The writer knows of no satisfactory procedure for calculating the effect of this practice. 2. Vertical movement of oil across the bedding planes of the reservoir rock hy gravity drainage tended to maintain a relatively high oil saturation, and hence a favorable K,/K, ratio, in the lower sections of the reservoir. As pointed out by Welge, this condition has aggravated the tendency for high producing GOR, but at the same time it has resulted in increased oil recovery. As may be seen from the performance charts for the various battery areas, operating (GOR&apos;S have been quite high for the last several years of reported history.

Jan 1, 1952

By B. A. Wilcox, A. H. Clauer

The tensile and creep deformation characteristics of fiber reinforced composites have been studied, primarily at room temperature. The matrix was an alloy of Mg-14 wt pct Li-1 wt pct Al (LA141A alloy) and the reinforcing fiber consisted of continuous wires of a high strength precipitation hardening stainless steel (AFC-77 alloy). The ultimate tensile strength and strength-to-density ratio of composites were much improved over that of the mmix, both at room ternperatwe and up to 200°C. Creep studies at room temperature revealed logarithmic weep behavior for wires and composites and steady state creep for the nonreinforced matrix. It was concluded that creep of the fibers controlled composite creep. The instantaneous logarithmic weep rate of the composite, 6, was related to the average tensile stress on the fibers, where n = 3.4. Mg-Li alloys are the lightest structural metals commercially available, e.g., the alloy LA141A (Mg-14 wt pct Li-1 wt pct Al) is 27 pct less dense than beryllium Although Mg-Li alloys have moderate tensile strengths at normal strain rates and ambient temperature, their creep strength is relatively poor, even at room temperature. Reinforcement by fibers offers a means of increasing the tensile strength as well as overcoming the limitations of low creep strength. With a proper choice of reinforcing filament, composites could be designed with higher strength-to-density and modulus-to-density ratios than the matrix alloy. This communication reports a study on the tensile and creep characteristics of alloy LA141A reinforced with continuous wires of a high-strength precipitation hardening stainless steel (AFC-77 alloy). The matrix has a bcc structure, with possible precipitates of AlLi and MgLi2A1,3 and is ductile at room temperature Stainless steel wire was chosen as the -reinforcing filament since previous work at Battelle4 showed that a good bond between wire and matrix could be produced in this system. For all volume fractions of reinforcing wire, the theoretical composite strength-to-density ratio is greater than that of the matrix and the modulus-to-density ratio is somewhat lower than that of the matrix. EXPERIMENTAL PROCEDURES The 0.004-in. diam AFC-77 wire was obtained from two suppliers: National-Standard Co.* and Crucible 0.13 Si, 0.18 V, 0.011 P, 0.012 S, balance Fe. In the as-received condition, wires from both sources had room-temperature ultimate tensile strengths of 585,000 to 590,000 psi with approximately 2 pct total elongation and 40 pct reduction in area. Composite preparation was accomplished by the vacuum infiltration technique. This involved placing the continuous wires in a mild steel tube (1/8-in. ID), capping one end of the tube with a sheet of the matrix alloy, and evacuating the other end of the tube. When the capped end was placed in a crucible of the molten matrix alloy and held for 31/2 min at 70O°C, the liquid metal was drawn up the tube approximately 7 to 8 in. A cross-sectional view of a typical composite is shown in Fig. 1. This preparation technique promoted excellent bonding between the matrix and wires, and porosity was rarely observed. Test specimens for both creep and tension studies were prepared by machining off the steel tube. Tensile tests on the wires and composite specimens were made in an Instron using a cross-head speed of 0.01 in. per min. The composite specimens had no reduced section and were held in self-tightening grooved serrated grips. Most of the specimens broke in the effective 1-in. gage section. Even though several tests fractured in the grip section, their ultimate strengths were essentially the same as those of specimens which fractured in the gage section. Creep specimens of the composite were gripped in a similar manner, and

Jan 1, 1970

By J. S. Browning

The U.S. Bureau of Mines has been experimenting with flotation processes to separate the spodumene-beryl ores mined at Kings Mountain, N.C. The success to date as well as the present status of the process is discussed. Further experimentation is underway and studies will be made on the milling costs involved in the flotation process. The pegmatites of the Kings Mountain-Lincoln ton, N.C., area constitute the largest known domestic reserve of beryl and spodumene. The reserve is estimated to contain 90 million tons of pegmatic material with 1,280,000 tons of recoverable Li,O(lithia) as spodurnene.&apos; The pegmatites also contain 0.4 to 0.5 pct beryl disseminated throughout the orebodies. The pegmatites may contain a potential reserve of 240,-000 tons beryl, equivalent to approximately 34,000 tons of BeO. Different flotation methods for separating beryl from feldspar or quartz, or both, have been developed by various investigators.2-7 On the other hand, published information is limited on concentration of spodumene-beryl ores. As the response of beryl and spodumene to flotation is essentially the same, a successful separation of the two minerals depends upon use of a selective depressant or a selective collector for one of the minerals. Several years ago, the U.S. Bureau of Mines, recognizing the need for developing a large domestic supply of strategic beryl, undertook studies to develop improved methods of recovering this mineral. Because of the low beryl content of the pegmatites, economic production of the beryl entails its recovery as a byproduct of spodumene flotation. Thus, the development of procedures that would provide for maximum recoveries of the spodumene, as well as the beryl, was a primary objective of the studies. Tests were made on run-of-mine ore and spodumene flotation tailing from the Foote Mineral Co.&apos;s spodumene concentrator at Kings Mountain (Fig. 1). Pet-rographic analyses of the ore and flotation tailing are given in Table I. Detailed analyses and examinations of the ore and tailings revealed that the beryllium was present in the form of a low-alkali beryl. The crystals were small, rarely larger than 14-mesh diam, and were clear and colorless. About 10 pct of the Li20 content of the ore was present in the mica and feldspar components of the pegmatite. In some weathered ores the associated clays also contained small amounts of lithia. This is typical of pegmatites in the Kings Mountain area. LABORATORY TESTS In the past, a vigorous chemical treatment of the spodumene surfaces with acid or caustic soda has been considered essential for satisfactory selective flotation of the spodumene from the other minerals in pegmatites. Many tests were made during this investigation to determine if chemical treatment of the spodumene could be eliminated in favor of a reagent combination that would depress the other minerals while selectively floating the spodumene. A simple reagent combination and process was developed that gave better spodumene recovery and grade of concentrate than the more elaborate acid or caustic treatment methods previously used. The finely ground ore pulps were conditioned with either an ammonium, alkali, or alkaline earth lignin sulfonate and sodium fluoride, and the spodumene was floated and cleaned using oleic acid as the collector. The spodumene tailing was deslimed, conditioned with sulfuric acid and coco amine acetate, and floated to reject mica. The mica tailing was thickened and conditioned with hydrofluoric acid, then washed to remove the acid. The washed pulp was conditioned with sodium hydroxide for pH control, and the beryl was floated and cleaned with oleic acid as the collector. Table II summarizes the results of the laboratory test work. About 77 pct of the spodumene and 75 pct of the beryl were recovered from the pegmatitic material. The spodumene concentrate assayed 6.1 pct Li20 and 0.01 pct BeO, and the beryl product assayed 3.0 pct Li20 and 1.57 pct BeO. Similar results were ob-

Jan 1, 1961

By J. Geertsma

The relationship between porosity and the speed of propagation of acoustic waves in fluid-saturated porous rocks as measured by the Sonic log and by ultrasonic tecbniques is analyzed. Biot&apos;s continuum theory 1 is used to explain the difference in acoustic wave propagation between a dry and a liquid-saturated porous material. The porosity is a variable in this theory. However, the acoustic wave propagation in the dry rock depends too on porosity, and this dependence is not predicted by the theory. Frequently in dry sandstones, a nearly linear relationship between reciprocal acoustic wave velocity and porosity is observed in the low-porosity range. The physics behind this behavior is outlined. An empirical relationship of the form, 1/v = A + F, applies accordingly for many porous dry rocks, provided the porosity is the only variable. The presence of a liquid in the pores changes the value of B, and this change is found to be in agreement with the Biot theory. The time-average relation introduced some years ago2 results in an equation of the same type — 1/V = F/Vf + (1 - F)/Vr — but is not based on a sound physical picture. Still, this relation sometimes predicts approximately correct A and B values. Carbonate rocks with their complicated pore structures sometimes show a different relationship between wave velocity and porosity, unfavorable for log interpretation. Examples are presented. The simultaneous presence of calcite, dolomite and anhydrite, with their different grain densities and matrix compressibilities, complicates acoustic-log interpretation in carbonate rocks still further. Other complicating effects of acoustic-log interpretation are discussed. They are related to the influence of shale streaks and natural fractures on the average wave velocity observed by the logging tool and to the effect of adsorption phenomena on wave propagation in unstressed rocks particularly in sandstones. INTRODUCTION The velocity of propagation of sound waves in porous sediments as a function of depth is a quantity frequently measured. Velocity loggers of various d-sign may be used, for which velocity is defined as the. distance between a wave generator and a wave detector (one-receiver system) or the distance between two wave detectors (two-receiver system), divided by the shortest time required for a vibrational pulse to cross this distance. Velocity loggers ale used to assist in seismic prospecting, to differentiate between the various types of sedimentary rock layers, and also to determine rock porosity and pore fluid content. This paper is especially concerned with the relation between velocity and porosity and the effect of the pore fluid. Most velocity-log interpretation in terms of porosity is based on a formula advocated by Wyllie, et al,2 suggested earlier by Hughes and Jones,3 and known as the "time-average relation". This formula app1ies for a model consisting of a layered system of parallel alternating slices of a solid and a liquid, crossed by the wave path perpendicular to the interfacrbs. This must be an unsuitable model for the derivation of wave propagation properties of liquid-saturated porous media. It suggests that only rock matrix and fluid properties influence the wave velocity. The surprising fact, nevertheless, is that applications of this formula to clean sandstones under specific conditions (sufficient effective stress) results in porosity predictions which are close to reality. Other authors, such as Gassmann,4 White and Sengbush,5 Brandt,6 and Hicks and Berry,7 make use of more realistic models to arrive at a wave velocity formula for porous sediments. Their models consist of various liquid-saturated packings of frictionless spherical grains and are, therefore, also highly idealized. A number of experimental results obtained in the laboratory can be better explained with these model theories than by the time-average relation. A study of a general character, not depending a priori on a special model of the porous structure, was still lacking.

By P. J. Root, J. E. Warren

An idealized model has been developed for the purpose of studying the characteristic behavior of a permeable medium which contains regions which contribute significantly to the pore volume of the system but contribute negligibly to the flow capacity; e.g., a naturally fractured or vugular reservoir. Unsteady-state flow in this model reservoir has been investigated analytically. The pressure build-up performance has been examined in some detail; and, a technique for analyzing the build-up data to evaluate the desired parameters has been suggested. The use of this approach in the interpretation of field data has been discussed. As a result of this study, the following general conclusions can be drawn: 1. Two parameters are sufficient to characterize the deviation of the behavior of a medium with "double porositym from that of a homogeneously porous medium. 2. These parameters can be evaluated by the proper analysis of pressure build-up data obtained from adequately designed tests. 3. Since the build-up curve associated with this type of porous system is similar to that obtained from a stratified reservoir, an unambiguous interpretation is not possible without additional information. 4. Differencing methods which utilize pressure data from the final stages of a build-up test should be used with extreme caution. INTRODUCTION In order to plan a sound exploitation program or a successful secondary-recovery project, sufficient reliable information concerning the nature of the reservoir-fluid system must be available. Since it is evident that an adequate description of the reservoir rock is necessary if this condition is to be fulfilled, the present investigation was undertaken for the purpose of improving the fluid-flow characterization, based on normally available data, of a particular porous medium. DISCUSSION OF THE PROBLEM For many years it was widely assumed that, for the purpose of making engineering studies, two param- eters were sufficient to describe the single-phase flow properties of a producing formation, i.e., the absolute permeability and the effective porosity. It later became evident that the concept of directional permeability was of more than academic interest; consequently, the degree of permeability anisotropy and the orientation of the principal axes of permeability were accepted as basic parameters governing reservoir performance. 1,2 More recently, 3-6 it was recognized that at least one additional parameter was required to depict the behavior of a porous system containing regions which contributed significantly to the pore volume but contributed negligibly to the flow capacity. Microscopically, these regions could be "dead-end" or "storage" pores or, macroscopi-cally, they could be discrete volumes of low-permeability matrix rock combined with natural fissures in a reservoir. It is obvious that some provision for the inclusion of all the indicated parameters, as well as their spatial variations, must be made if a truly useful, conceptual model of a reservoir is to be developed. A dichotomy of the internal voids of reservoir rocks has been suggested.7,8 These two classes of porosity can be described as follows: a. Primary porosity is intergranular and controlled by deposition and lithification. It is highly interconnected and usually can be correlated with permeability since it is largely dependent on the geometry, size distribution and spatial distribution of the grains. The void systems of sands, sandstones and oolitic limestones are typical of this type. b. Secondary porosity is foramenular and is controlled by fracturing, jointing and/or solution in circulating water although it may be modified by infilling as a result of precipitation. It is not highly interconnected and usually cannot be correlated with permeability. Solution channels or vugular voids developed during weathering or burial in sedimentary basins are indigenous to carbonate rocks such as limestones or dolomites. Joints or fissures which occur in massive, extensive formations composed of shale, siltstone, schist, limestone or dolomite are generally vertical, and they are ascribed to tensional failure during mechanical deformation (the permeability associated with this type of void system is often anisotropic). Shrinkage cracks are the result

By J. B. Stubbins, D. F. Coates, K. L. McRorie

Twenty-two pit slides that occurred in two Canadian open pit mining properties are analyzed. Information on the results of laboratory tests of the rocks and a brief description of the geological environment are also presented. One deduction from the study is that slides seem to be predictable by using established theory. This corroboration indicates that, contrary to normal mining practice, the appropriate slope angle should vary with the height of the wall. In addition, if the general ground water level around an open pit can be reduced, the appropriate slope angles of the walls could then be increased by a determinable amount. The ultimate objective of these investigations is to determine the relationship between the percentage probability of failure of any slope designed with specific strength paraheters. With this relationship it would then be possible to determine optimum slope angles. Because of changes in various economic factors, open pits are now being mined to much greater depths than previously. The need to keep stripping ratios low without endanrrerine.-- lives and equipment provides a strong incentive to determine the maximum practicable wall slopes. Applied research work is currently being conducted to establish the methods for analyzing optimum slopes.

Jan 1, 1963

By W. Luyken

A NUMBER of articles have been published, notably those by R. S. Handy, R. T. Hancock and A. P. Watt in Engineering and Mining Journal, dealing with the calculations involved in ore dressing.. These publications demonstrate both, the importance of the subject and the lack of success in developing a generally recognized method for comparing enrichment effects. Considering that we may wish -to compare enrichment results on similar or dissimilar ores, that we may desire to make the comparison on the basis of either the absolute or the economical efficiency, and that the number of factors upon which the result depends is large, the question arises whether it is possible to set up a positive method for such calculations. In the following pages it is our aim to show that a sure, complete and successful way to overcome existing difficulties has been found. GRAPHICAL ANALYSIS OF ORE-DRESSING PROCESSES The following is from Truscott&apos;s Text Book of Ore Dressing (London, 1923) x = assay of ore treated (feed). y = assay value of the concentrate. z = assay value of the tailing. a = weight of feed. b = weight of concentrate. c = weight of tailing. C = fractional concentration = b/a= x-z/y-z (1) K = ratio of concentration = 1/C = a/b =y-z/x-z (2) R = fractional recovery = yb/xa = Cy/x. (3) 100R = percentage recovery. Copt = theoretically best concentration. 100 - Copt = waste in the feed.

Jan 1, 1929