Search Documents

1. What Effect Has Sulfur Or Vanadium (In The Oil) On The Steel With Your Burner? 2. Also, what is the decibel rating on the floor when your burner is on? AUTHORS' REPLY 1. There is no effect. 2. The decibel rating is 98-99 decibels.

Jan 1, 1972

By M. C. Leverett

KNOWLEDGE of the theory underlying the behavior of mixtures of fluids in reservoir rocks is essential to the proper solution of certain types of problems in petroleum pro-duction, but is as yet incompletely devel-oped. The object of this paper is to show the application of well established thermody-namic and physical principles to these prob-lems, and thus to assist in the development of the basic theory. For convenience the problems to be considered here may be divided into two groups: I. Static problems, involving only the static balance between capillary forces and those due to the difference in densities of the fluids; i.e., gravitational forces. 2. Dynamic problems, involving analysis of the motion of mixtures of immiscible fluids in porous media under the influence of forces due to gravity, capillarity, and an impressed external pressure differential. CAPILLARY EQUILIBRIUM IN SANDS Under this heading the static type of problem will be discussed and the results of experimental investigations on the capillary properties of unconsolidated sands will be presented. Although the discussion of this section is, in a sense, prefatory to the treat-ment of problems of mixture flow, the con-cepts developed here have considerable intrinsic importance apart from their ap-plication to flow problems. For, it is reason-able to postulate that the reservoir fluids are, owing to their long existence in undis-turbed mutual contact prior to exploitation, in substantial equilibrium. It follows that their distribution in the reservoir at the time of tapping should be entirely predict-able from the theory of capillary equi-librium, provided certain experimentally measurable properties of the reservoir rock are known. Knowledge of the distribution of the several fluids in the reservoir is, of course, helpful in the estimation of reserves and in other problems. It is to be emphasized that throughout the discussion of capillary statics it is as-sumed that the fluids are in equilibrium from the capillary standpoint. Thus, water, where it is referred to as being in a reser-voir, will be understood to be interstitial water, present at the time of drilling the reservoir, commonly termed "connate" water. The theory developed here is perfectly general for any porous solid, whether a carefully prepared unconsolidated sand or a natural sandstone from an oil reservoir. At present, however, only problems in-volving clean, unconsolidated sands can be made to yield numerical solutions, since only such sands have been adequately in-vestigated experimentally. Experimental evaluation of the pertinent properties of natural reservoir rocks will permit the ex-tension of the numerical treatment to prob-lems involving these materials. We shall now consider in some detail the static equilibrium of fluid mixtures in porous solids; that is, the manner in which the reservoir fluids are distributed vertically when the forces due to capillarity are just balanced by those due to gravitation.

Jan 1, 1940

By R. G. Garlick, H. B. Probst

Tungsten single-crystal specimens of various orientations were deformed in tension at room temperature. Slip traces indicated both (112)(111) and (110) (111) slip; however, about 10 pct plastic dejormation was required bejore these traces could he seen. Resolzled shear-stress considerations indicated that at least some of the particular systems observed were not those on which slip initiated hut were secondary systems. This is highly probable, considering the high plastic strains involved. Analysis of the stress data with respect to possible slip systems indicated that slip must have been initiated at stresses below the proportional-limit stresses measured. ALTHOUGH there is general agreement that slip deformation in fcc and hep metals takes place on the plane of close packing and in the direction of close packing, there is no such agreement for slip in bcc metals. It is generally agreed that the close-packed direction (111) is the slip direction, but investigations have led to conflicting descriptions of the slip plane. As Hoke and Maddin1 point out, there are essentially four points of view. 1) Deformation in bcc metals is composite shear on (112) and (110) planes or on nonparallel (110) planes, and any apparent slip on other planes can be accounted for completely by slip on these planes. Chen and Maddin have reported this to be the possible case for molybdenum." 2) Slip occurs in the (111) direction and is limited to {110), {112), and (123) planes (the three closest packed planes of the lattice). 3) Slip occurs in a (111) direction, but not necessarily on planes of close packing (banal slip). 4) Slip occurs in those directions and on those planes for which ß, the ratio of Burgers vector to interplanar spacing, is a minimum. The slip systems of the bcc metal tungsten have never been fully determined, although several investigators have reported pertinent results.3"7 The present work was initiated to determine the active slip systems in tungsten at room temperature, the critical resolved shear stresses associ- ated with these systems, and the orientation dependency of operative systems. These features of tungsten deformation at room temperature have never been reported in the literature. The authors find this somewhat surprising, particularly in view of the availability of tungsten single crystals since the advent of electron-beam zone-melting techniques and the widespread interest in refractory metals. It would seem apparent that such work has been attempted but the results have not been reported, possibly due to the conflict with deformation theory. The results of the present work conflict with any straightforward description of deformation based on the proposed explanations of slip in bcc metals. Although these conflicts have not been resolved, a presentation of the problem seems in order and should be of value to others working in this field. MATERIALS AND PROCEDURE Single-crystal tungsten rods of 1/8-in. diameter were grown from undoped commercial rod by one-pass electron-beam zone melting in apparatus previously described by witzke.8 Representative analyses of the rod before and after melting are given in Table I. There was no detectable zoning of impurities during melting. Buttonhead tensile specimens, as shown in Fig. 1, were machined from single crystals. Two flats 90 deg apart were ground in the gage length of each specimen. These flat surfaces facilitated the analysis of slip traces. No attempt was made to position these flats with respect to the crystal orientation. The worked surface layer of the machined specimens was removed by electrolytic polishing in a NaOH solution. Tensile-axis orientations were determined by standard Laue back-reflection techniques. The sharpness of the Laue spots indicated that the crystals were free of strain.

Jan 1, 1964

By J. H. Henderson, T. E. Morrisson

An irvestigation has been made of the production of oil through horizontal fractures of high capacity and large radius placed at the base of producing formations. The specific aitns of the study were to (I) determine by model studies the reservoir performance when gravity drainage is the only producing mechanism, and (2) develop a method of predicting such perfortnance from commonly measured reservoir proper-ties. Although the theoretical approach tailed to develop a rigorous analytic sorution to the transient problem, it (lid lead to a practical method of predicting performance. Predictions (Ire in good agreement with rates and recoveries observed in scaled-model experinzents. Capillary effects and the influence of relative permzenbil-ity are taken into account. The experimental program was mainly concerned with the influenre of fracture radius, fracture capacily and capillary hold-up on the total recovery and the rate of recovery. Much of the experimental work was done on a triangular model which represented one-eighth of a square well pattern, so constritcted that horizontal fractures of varying radii and flow capacity could be studied. An electrolytic model was used to relate the initial production rates to fracture radius, formation thickness and the drainage radius of the well pattern. The conclusions reached as a resrtlt of the work are as follows. I. The production of oil under gravity force alone into a well-propped horizontal fracture, whose radius is of the order of hundreds of feet, is a recovery method which combines high recoveries with very acceptable production rates. 2. The mechanism is effective in "dead oil" reservoirs as well as in reservoirs which possess the energy of solution gas. 3. A method of predicting performance has been developed which gives good agreement with experimental behavior in cases of practicnl interest. Even for very thick beds and large fracture radii, where actual conditions do not conform to the assumptions made, the method gives order of magnitude predictions which would not otherwise be possible. INTRODUCTION Gravity drainage of oil from a formation which has continuous ver- tical permeability over a reasonable depth interval is a surprisingly effective method of recovery. However, for a conventional well the production rates which result from gravity drainage are so low that the economics are seldom attractive. The same formation may produce rapidly and profitably by gravity alone through a high capacity, extensive (i.e., > 100-ft radius) horizontal fracture placed near the bottom of the pay section. Fig. 1 shows a schematic diagram of the plan. Energy in the reservoir gas is not a necessary condition for this recovery process. With a sufficiently large fracture, attractive production rates will result from gravity flow alone, and the producing GOR need only be the solution GOR. It is, of course, necessary to keep the fluid level in

By Pradeep K. Rohatgi, Clyde M. Adams

Dendritic aggregate of ice formed on freezing of aqueous soluitions has been studied. Chlorides of sodium, potassiutn, lithiunz , and hydroget1 were used as solutes. The spacing between ice platelets or den-drites was experimenlally found proportzonal to the square root of freezing time when the freezing rate was constant from beginrting to end of solidification; the constant freezing rates were obtained during freezing of small droplets of aqueous soliitions surrounded by relatively large heat sinks. The transverse growth velocity of the ice platelets is proportional to the square root of the freezing rate. During unidirectional freezing from a constant temperuture chill, the solution at each location is subjected to a spectrum of freezirtg rates. The freezing rate is ini- FREEZING of solutions has been a subject of investigation in many disciplines. Aqueous solutions offer the advantage of transparenty; their study is of special significance due to the increasing interest in freezing processes for desalination. In addition dendritic solidification of aqueous solutions is in many ways analogous to freezing of metallic solutions. Aqueous solutions of most ionic salts freeze with tially low, passes through a maximum, and then decreases until solidificatimz is complete. The den-drite spacing increases linearly with the distance from the chill surface; it is inversely profiortional to the square root of the maximum freezing rate. The dendrite spacings in the two systems (the constanl freezing rate and the varying freezing rate) are equal, when the maximum freezing rate of the varying freezing rate system equals the average freezing vale of the constant freezing rate system. Mass transport in interdendritic liquid duriug solidificatiotz is analyzed; the experimental observations indicate that maximum concentration difference (AC) and supercooling (AT) in the interdendritic liquid are indepexdent of freezing rate. the separation of practically pure ice crystals from the liquid phase; with very few exceptions there is no solid solubility of ionic salts in ice. As an ice crystal grows there is rejection of solute from the moving interface into the liquid. Since the rejected solute moves primarily by diffusion, concentration gradients are established in the liquid. The highest solute concentrations are found in liquid immediately adjacent to liquid-solid interfaces and lowest concentrations farthest from the interface. Two-phase equilibrium obtains only at the solid-liquid interface; at other locations the liquid becomes supercooled because temperature gradients are negligible compared to concentration gradients. This is an immediate consequence of the fact that thermal diffusivities are considerably higher than mass diffusivities.

Jan 1, 1968

By Richard L. Gordon

Minerals long have been important commodities in international trade. As an inevitable result, the governments of the world have employed a wide variety of programs that affect the flow of trade. Roughly speaking, we may distinguish between the desire of more developed countries (MDCs) like the United States, western Europe, and Japan to control imports of minerals and the concern of less developed countries (LDCs), like India, about exploiting and exporting their minerals. The terminology used to describe different countries and the classification of specific countries into groups is unsettled and often changing. The poorest countries have been characterized as backward, undeveloped, underdeveloped, and developing. The problem seems to be in selecting a term that is both accurate and polite. Less developed seems, for reasons outlined by Hagen [pp. 51-57], the most convenient term. The borderline between an LDC and an MDC is always open to dispute. Objective measures are difficult to develop because of deficiencies in basic data, and enormous conceptual problems arise in making valid comparisons from even good data [see Hagen, pp. 7-28]. Thus, policies of the MDCs can be evaluated chiefly by using a few basic arguments for protectionist attitudes towards international trade. In dealing with the LDCs, a more far-ranging evaluation that covers general economic policy goals, the role of foreign investment, and the indirect effects of trade is required. This duality breaks down when trying to deal with the depressed areas in an MDC; here the issues are more akin to those associated with problems in an LDC. Similarly, variants of arguments used in LDCs appear in debates about foreign investments in MDCs. The whole discussion of minerals in LDCs, moreover, has obvious implications for MDCs like Canada and Australia. They, too, must face problems about the best utilization of their resources. THE RESTRICTION OF MINERAL TRADE BY DEVELOPED COUNTRIES[a] At least to some extent, the world's leading industrial nations have intervened to control the inflow of minerals. Such regulation is particularly pronounced for energy. Both the United States and western Europe employ

Jan 1, 1976

By C. C. Wright, R. J. Day

ALTHOUGH data on the exact tonnage of recoverable coal silt are not known, the quantity produced in 1943 was estimated to be over five million tons for the anthracite region of Pennsylvania alone. Since that time the recovery of the No. 5 buck- wheat size previously included in silt estimates has increased greatly thus reducing the total silt tonnage. As a compensating factor, however, the methods of recovering silt previously escaping into the rivers and streams have been markedly improved so that the net figure may not have changed materially. Comparable estimates for bituminous coal are lacking, but undoubtedly the silt represents a significant tonnage. With the trend toward increased wet cleaning of the smaller sizes of bituminous coal, it is to be expected that even greater quantities of silt will be available in the future. The raw silt from anthracite collieries usually contains a high mineral matter content, but technological developments in fine coal cleaning have been making rapid advances and it appears probable that more extensive use of these methods will be employed in the near future. Bituminous coal silt in many instances contains a similar high mineral matter content. As with anthracite silt, however, the cleaning of this material, where necessary, appears both technologically and economically feasible. With a view to upgrading the size and value of silt, considerable laboratory and pilot plant work has been conducted by a number of organizations on what is commonly known as pelletization. Actually the process is one of extrusion in which the moist silt is extruded from a die in the form of rods, which usually break into relatively short lengths-a few inches long-as they fall from the die. Fig I is a photograph of some extruded 3/8-in. diam pellets and of the anthracite silt from which they were produced. This technique of producing larger sized material from fines is by no means new, having been used extensively by the industrial carbon and clay industries for years.' The application of the process to coal silt appears, however, to be relatively new. The first major program of investigation dates back only to July 1945, when a group of engineers representing the Anthracite Institute, The Pennsylvania State College and the J. F. Pritchard and Co. conducted preliminary tests on the extrusion of anthracite silt at the Floridin Co. plant at Warren, Pa. Since that time these three organizations-individually, together, and in co- operation with other interested groups- have actively pursued work on various phases of the problem. Much of the early history and details of the laboratory and pilot plant work by the Anthracite Institute, has been reported by Mulcey and Eckerd.2 It is the purpose of this paper to report additional information on the process, especially with respect to the factors influencing the quality and use properties of the product, and the current develop

Jan 1, 1948

By V. J. Kniazeff, S. A. Naville

The problem of unsteady-state condensate-gas flow through porous media leads to a set of second-order non-linear partial differential equations. Such a set of equations is numerically solved in the case of radial two-phase flow around a well, taking into consideration both the thermodynamical properties of the fluid and the mechanical properties of the reservoir. The fluid properties, reflecting the PVT relationship of the gaseous and liquid phases, are expressed by using the partial specific masses of the two main separator products in these phases. The flow properties of the reservoir rock are expressed by the generalized Darcy's law for the liquid phase and by a quadratic relationship between the rate of flow and the pressure gradient for the gaseous phase. The numerical solution of the equations for pressure and saturation US radius and time is worked out through programs written for a computer. The evolution of bottom-hole pressures, well productivities or- deliverabilities and effluent compositions with the depletion of the reservoir is easily derived. The application to the Saharian gas-condensate field Hassi R'Mel led to a better understanding of the drainage mechanism. A zone of fairly high liquid saturation develops around the wells, reducing the effective permeability, and represents a loss of condensible products in addition to the PVT-like retrograde condensation. lnside this zone, near the well, the deviation from Darcy's law for the flow of the gaseous phase governs the well deliver-ability. A back-pressure test has been computed and correlates with the field results. INTRODUCTION Two-phase flow of volatile hydrocarbons, like condensate gas or light crude oil, may be treated as the flow of a binary mixture by an arbitrary division of the chemical components into two groups. This is translated into two equations of mass continuity, which constitute a set of relation- ships for the pressure and the saturations vs the space coordinates and the time. The equations contain the laws governing the composition and the motion of the phases. The problem so defined is solved with the assumption that the compositions of the phases at any pressure are respectively the same as those observed in a PVT measuring cell under differential liberation. In a first series of computations, it was assumed that the flow obeys the generalized Darcy's law. A satisfactory representation of the retrograde condensation around the well was thus obtained. In addition, the trend toward decreasing effective permeabilities was obtained, and the computed composition of the effluent checked the laboratory values. However, it has not been possible within this basic assumption to represent the non-linear relationship between the production rate and the bottom-hole pressure drawdown as observed for gas wells in the field. Following the advice of A. Houpeurt it was decided to consider the relative permeability to gas as a function of the velocity of the gas Phase.1 The necessary physical determinations were made by E. COstaséque using a method devised by A. Houpeurt and R. Iffly. As numerical processing of the equations progressed, several difficulties were encountered which were overcome through collaboration with the computer manufacturer. This mathematical model of two-phase flow in porous media had been primarily intended for and extensively applied to the case of the Hassi R'Mel gas-condensate field, operated by SN Repal for SEHR, a joint subsidiary of SN Repal and CFP (A). The programs have also found their applications to forecast the behavior of several fields in the Sahara area containing light and volatile hydrocarbons. BASIC EQUATIONS We will consider a zone in the porous reservoir where the flow properties and the in situ composition of the fluids can be assumed to be uniform. A part of the equations of transient flow can be written with the specific gravity of the fluids being taken equal to the sum of the contributions due to the

Jan 1, 1966

By James A. Barr

Phosphate rock is a natural rock containing one or more phosphate minerals usually calcium phosphate, of sufficient purity and quantity to permit its use, either directly or after beneficiation in the manufacture of commercial products.1 The principal minerals in phosphate rock have the apatite structure which may be represented by the type formula: Ca10(X2) (PO4)6 where X represents the hydroxyl group (OH), chlorine or fluorine, either singly or collectively. The calcium may be partly replaced by sodium, magnesium, and other positive ions such as manganese, strontium, lead, uranium, cerium, yttrium and other rare earths. The PO4 radical may be partly replaced by small quantities of UO4, AsO4, SiO4, CO3, SO4, or Vo4. A typical commercial rock is usually a calcium phosphate containing 3 to 4 pct fluorine, the major impurities being limonite or other iron oxides, clay, aluminum phosphates and silica as quartz sand. A little vanadium is present in most of the domestic rock deposits (except the Tennessee Brown Rock), according to Jacob, Hill, Marshall and Reynolds! A little uranium occurs in the Florida leached zone, as will be brought out later. The chemical analyses are reported as P205, or tricalcium phosphate Ca3(PO4)2, the latter often designated by the trade name BPL (bone phosphate of lime). Commercial analyses usually report iron and alumina as oxides, lime as CaO and silica or insoluble. Colony3 examined many samples of apatite, staffelite, dahlite and American phosphorites and concluded that all have identical X-ray diffraction patterns. The phosphates in the phosphate rock have very minute crystalline structures. The mineral apatite Ca3(F.Cl) (PO4) 3 is the principal primary source of the element phosphorus, and occurs widely distributed in igneous rocks but rarely in a minable mass. Only about 12 pct of the world production of phosphate rock comes from primary apatites; the remainder is derived from secondary phosphorites. These phosphorites have been formed by the alteration of sediments by solutions containing phosphoric acid. Such solutions have come from the weathering or leaching of igneous rock containing apatite, bone deposits of prehistoric animals, marine life or guano deposits. These phosphorites are mostly alterations of phosphatic limestones. The sedimentary phosphate deposits are of marine origin and may have been enriched by subsequent solution of the more soluble calcium carbonate by waters containing carbon dioxide, by physical concentration by wave action, and by redeposition of the dissolved phosphate ions. Uses of Phosphate Phosphorus is the spark of life and is the structure builder and one of the main elements of plant food (fertilizer). Without phosphorus, life cannot exist. A "complete" plant food[t] in addition to phosphorus compounds contains potash, which acts as a catalyst to convert nutrients to useful forms, nitrogen to supply the growth element and many minor elements. The cycle of supply of phosphorus is from the apatite to solution and soil, absorption of plant life, decay and return to the soil or by animal life feeding on the plants. With insufficient supply of phosphorus in vegetation, life is not prolific. If crops are removed from

Jan 1, 1960

By A. M. Adair

The effect of cathodically charging zone-refined iron with hydrogen and the resultant yield stress-grain size relationship has been investigated by tensile testing at -31°C. The resulting Petch plots (using a least-squares analysis) reveal a significant reduction in the slope and an increase in the intercept for specimens cathodically charged with hydrogen, regardless of whether the hydrogen is present during testing or is removed by evacuation. Other than surface blistering, the major effect of cathodically charging this material is to create occasional grain boundary cracks and thus presumably a large number of free dislocations at grain boundaries. These results are consistent with the hypothesis that the slope of the Petch plot is related to the stress required to activate dislocation sources at or near pain boundaries. While there is no significant effect of the presence of hydrogen on the lower yield stress of this material, the ductility is considerably reduced. After hydrogen removal by evacuation, the ductility recovers substantially and almost complete recovery of ductility is experienced by the smaller grain size specimens. THE influence of hydrogen on the mechanical properties of ferritic materials has received much attention throughout the history of the metallurgy profession. This interest has stemmed from the obvious importance of preventing the catastrophic failure of parts in service, and from the desire to determine what mechanism is responsible for the observed behavior. The various mechanisms proposed for hydrogen em-brittlement have been discussed in detail by Tetel-man,'who concludes that a combination of the applied stress and hydrogen pressure within voids best accounts for the many experimental observations reported. From a quite reasonable correlation of the strain aging and delayed-failure behavior of a variety of materials,2-7 Troiano and coworkers are of the opinion that the delayed-failure mechanism (slow strain rate embrittlement as well) is better explained as a lattice effect; solute elements diffuse to regions of high triaxial stress, form uncondensed atmospheres there, and effect a reduction in the cohesive strength of the lattice. Since hydrogen yield points8,9 have been observed in ferritic materials, and since the hydrogen embrittlement process may be related to strain aging, one further contribution to embrittlement could be hydrogen-dislocation interactions which make crack blunting by plastic deformation a more difficult process. The etch" relationship offers a means of comparing the relative ease of initiating and propagating plastic deformation in metals and alloys. In the present study, this relationship was used to compare the behavior of zone-refined iron in three conditions: uncharged, cathodically charged with hydrogen, and cathodically charged with hydrogen and evacuated. These Petch plots and the observed ductility parameters allowed a separation of the effects of the very presence of hydrogen and the act of cathodically charging hydrogen into this material. MATERIALS AND EXPERIMENTAL PROCEDURE An ingot of zone-refined iron was obtained from Battelle Memorial Institute which contained the following (typical) interstitial impurities in ppm: carbon, 10 * 5; nitrogen, 1; oxygen, 22; hydrogen, 0.9. The ingot was cold-reduced to a 1/2-in.-sq cross section, recrystallized 1 hr at 575°C, and then straight-rolled to a thickness of about 0.105 in. Tensile specimens were milled from the strip having a 1-in. gage length

Jan 1, 1967

By R. J. Blackwell, J. R. Rayne, J. R. Henderson, W. M. Terry, D. C. Lindley

This paper presents the results of a laboratory investigation of the efficiency of water-solvent mixtures in recovery of oil. These mixtures may have the high displacement efficiencies characteristic of solvent floods and the high sweep efficiencies characteristic of water floods. Thus, the water-solvent process may increase the number of reservoirs in which a miscible-type displacement can be used profitably. The experiments on the use of water-solvent mixtures for recovery of oil were conducted to find the general applicability of the process. These studies demonstrated that, in flowing through sands, water and solvent segregated into a solvent layer on the top and a water layer on the bottom rather than flowing through the sands as a uniform mixture. Calculations based on the simultaneous flow of the water and solvent in layers were used to predict the effective mobility of the mixtures and the optimum operation of the process in steeply dipping, homogeneous reservoirs. As most reservoirs are not suited for the operation of the process under ideal conditions, experimental studies were conducted with sand-packed models scaled to represent more realistic reservoirs. These studies included the effects on recovery of oil of rate of injection, viscosity of oil, variations of permeablity within a formation and variations in water-solvent ratio. For the range of con-ditions studied, higher recoveries of oil were obtained with water-solvent mixtures than with water or practical volumes of solvent alone. INTRODUCTION A group of intriguing—because of their great possibilities—new oil recovery methods at the disposal of the petroleum engineer are the miscible displacement processes. These processes (high-pressure gas drive, en-riched-gas drive and LPG bank driven by methane) displace all of the oil from the portions of the reservoir swept by the injection fluid. The key question confronting the engineer applying one of these techniques to a particular reservoir is, "What fraction of the reservoir can be swept by injection of a practical volume of solvent?"." Intensive laboratory studies have been made during the past several years in seeking answers to the question of the sweep efficiencies which can be expected in solvent floods.' - These studies provided the answer that low-viscosity, low-density solvents channel and by-pass oil in sands with no dip. In horizontal sands, solvent flooding becomes less efficient as the viscosity of the oil increases, the recovery of oil at solvent breakthrough decreases and larger volumes of solvent are required to achieve a given recovery. More efficient displacement of oil by solvent is observed under certain conditions in sands with dip.".' If the permeability and dip of the sand are sufficiently high, gravity segregation of low-density solvent injected updip can prevent channeling. At rates of depletion below a critical rate,"." no channeling occurs. Unfortunately, in many reservoirs, the critical rate is so low that production of oil at rates below this rate is not economically attractive. And at rates over four times the critical rate, channeling is almost as severe in sands with dip as in horizontal sands. These findings pointed out that, for solvent floods to be generally applicable in recovering oil from all types of reservoirs, new methods of improving their sweep efficiencies are needed. Simultaneous injection of water with the miscible fluid was suggested by Caudle and Dyes7 as a method for improving sweep efficiencies. They theorize that water flowing with the solvent would decrease the effective mobility of the solvent and cause it to contact more oil sand. If, indeed, the water and solvent flowed as a uniform mixture, the process should have the advantages of the high displacement efficiencies characteristic of miscible floods and the high sweep efficiencies of water floods. Thus, the method (at least in theory) would greatly increase the number of reservoirs in which miscible-type displacements would be feasible. A research program was conducted to probe the technical feasibility of the water-solvent process. It

By M. C. Smith, W. V. Green, D. M. Olsen

The creep-rupture behavior of commercial powder-metallurgy molybdenum rod is reported in the temperature range 1600" to 250O°C, at stresses up to 9000 psi and times up to 1 month. The effects of temperature, stress, and grain growth are discussed. Rupture time is fitted to the Larson-Miller parameter and compared to lower-temperature and higher-stress results reported by pugh.1 BECAUSE of its high melting point, molybdenum should retain useful strength to relatively high temperatures. Combined with its ready availability in the United States, this makes it attractive for many applications in missiles, rockets, and so forth—wherever its susceptibility to oxidation can be tolerated or overcome. The mechanical properties of molybdenum rod in the temperature range —200" to 1540°C have been reported by pugh,' Bechtold,' Parke,3 and Carriker and Guard.4 Madden and chen5 have measured the tensile properties of molybdenum single crystals in vacuum up to about 2500°C. As one further step in evaluating its mechanical usefulness, the constant-load creep-rupture properties of commercial powder-metallurgy molybdenum rod have been investigated in the range 1600" to 2500°C. MATERIAL TESTED Creep specimens were machined from 1/2-in. round commercial molybdenum rod, manufactured from powder by pressing, sintering, and swaging. Spectrochemical analysis of the rod showed "traces" (less than 0.01 pct) of silicon, aluminum, chromium, iron, and zirconium, and "faint traces" (less than 0.001 pct) of manganese, magnesium, cobalt, and nickel. Carbon content was 130 to 200 ppm, nitrogen was 110 to 180 ppm, and oxygen 30 to 35 ppm. A typical microstructure of the as-received rod is shown in Fig. 1. Room temperature tensile properties for five specimens strained at about 0.015 in. per in. per min are shown in Table I. CREEP SPECIMENS USED The specimens used for creep-rupture testing are illustrated in Fig. 2. The 1/4-in.-diam gage section was 3/4 in. long, and terminated at shoulders 5 mils high. These shoulders served as fiducial marks for optical strain measurements. Surface finish on the gage section was 16pin. r.m.s. One specimen, for a "long-time" test described below, was modified by dividing the 3/4-in. gage length into three 1/4-in. long sections with individual diameters of 0.250, 0.230, and 0.210 in., each terminating in a pair of fiducial shoulders. TESTING PROCEDURE The constant-load creep-testing machine used has been described by Smith, Olson, and Brown.6 In it the specimen is held vertically on the axis of a cylindrical tantalum or tungsten heater tube by threaded molybdenum or tungsten grips. Both specimen and grips are heated by radiation from the heater-tube, which is heated by its own electrical resistance. The bottom specimen grip is held at its lower end by a clevis pin. The testing load is applied to the specimen through the upper grip by means of hanging weights, a constant force-multiplication lever system, and a pull rod sealed to the chamber lid by a bellows. The incandescent specimen is viewed by an external optical system through slots in the heater-tube and radiation shielding, and an enlarged image of it is projected on a ground-glass screen. Gage-length measurements are made on this image with a pair of cathetometers. Thorium oxide coatings were applied to the threaded ends of most specimens, to prevent diffusion-welding of specimens to grips during testing. Without such a coating welding usually occurred, and grips were often broken by subsequent efforts to remove the tested specimens.

Jan 1, 1960

By D. S. Gleason, D. E. Severson, D. R. Skidmore

Pittsburg and Midway Coal Co. has modified the German Pott-Broche process, on which patents date back to 1927, to produce on a bench scale liquid products by solution hydrogenation of coal. A continuing program of lignite solution-hydro gena-tion experiments is directed toward investigating coal solution reactions, determining favorable conditions for the solution refining of lignite by the Pott-Broche process, and investigating some of the uses for the de-ashed product obtained from lignite The German Pott-Broche process1" on which patents date back to 1927, has been modified by the Pittsburg and Midway Coal Co., a Gulf Oil subsidiary, to produce on a bench scale liquid products by solution -hydrogena-tion of coal." The objectives of the present effort are to investigate coal solution reactions, to determine favorable conditions for the solution refining of lignite by the Pott-Broche process, and to investigate some of the uses for the de-ashed product obtained from lignite. This paper is a summary of results to date in a continuing program of lignite solution-hydrogenation experiments. The coal solution reaction program has several principal aims. The first of these is to determine whether lignite can be successfully dissolved in solvents that might be practical for commercial development. The second object is to determine whether the solvents function after successive cycles of use, recovery, and reuse. It seems necessary to the economics of a potential commercial process that the solvent be recycled. Third, it is desired to learn something about the distribution of the ash constituents between cake and filtrate. The extent of ash removal is important. The nature and quantity of mineral matter passing through the filter may determine end-use marketability. For certain use applications, trace quantities of certain minerals can be objectionable, e.g., titanium and vanadium must be very low in electrode carbon for aluminum production. The Solution Reaction The coal solution Process involves an extremely complex system of chemical reactions. An initial solvent such as anthracene oil is a mixture of hundreds of different compounds with a boiling range of roughly 500" to 750°F at atmospheric pressure. The coal macro-molecule is broken down by thermal decomposition and solvent action into myriads of different compounds, some the same as those comprising the solvent. This similarity in structures opens up the possibility of production and subsequent recovery of solvent. Some solvent is inevitably lost by reaction. Regeneration of solvent was not a problem in the early German Pott-Broche plant. The coal refinery was an integral part of a petroleum refinery complex and replacement solvent was readily available. A coal refinery using lignite, however, might be isolated from other hydrocarbon processing facilities and the regenerability of solvent could be vital to the economic success of the venture. Several structural features of the solvent molecules have been cited as important to the coal solution process.'. The first of these is aromaticity of the material, the second, ability to transfer hydrogen to another molecule, as for example the ability of tetralin to transfer hydrogen and be converted to naphthalene. Finally, the presence of hydroxyl groups on aromatic rings within the molecule, i.e., phenolic character, seems beneficial. Mixtures of pure compounds have been tried by various investigators. Mixtures of o-cresol, a phenolic substance, and tetralin were found to dissolve bituminous coal better than either substance alone.3 This maximum solubility was not found with lignite." Hydrogen contributes to the reaction by hydro-genolysis and by combining with free radicals and molecular "loose ends" to stabilize the compounds formed in coal depolymerization. High boiling point, and correspondingly high molecular weight, seems to be a property which improves solution potential for coal with a given type of compound.' The maceral components of the coal appear to have an important bearing on its ease of solution. The fusain portion is quite inert to solvent action, but the an-thraxylon material dissolves quite readily.3 The hydrogenation reaction can be improved by the use of a catalyst; commercial hydrogenation catalysts having been found effective. Although cost is involved in the use of catalyst and catalyst recovery, the resulting saving in time and perhaps lowered temperature or pressure might justify their use in the solution refining process and decrease the total process costs. Apparatus and Procedure The coal solution runs were made in a 1-gal stainless steel stirred autoclave. The autoclave was provided with thermocouple wells and a transducer to permit continuous recording of temperature and pressure. The autoclave stirrer was magnetically driven, eliminating the leakage inherent with a rotating pressure seal. For runs in which a catalyst was used, the catalyst in the form of beads was placed in a wire mesh container mounted on the stirrer shaft. A control system programmed the heatup and reaction cycle. The permissible heating rate was 5°F per min because of the need to minimize thermal stress in the autoclave body. The temperature was raised at that rate until the reaction temperature was attained and then the temperature was held constant for the desired length of time. The maximum temperature seldom exceeded the average run temperature by more than 15°F.

Jan 1, 1971

By Tasuku Fuwa, John Chipman, David H. Kirkwood

Fe-C-Si alloys in silica crucibles were held at 1600°C in a controlled atmosphere of CO and Co2 and the approach to equilibrium was obsertsed. Results were not of sufficient precision to establish the activity and interaction coefficients. Observations 012 the equilibrium provided an average value for the standard free-energy change which differed by + 1.1 kcal from the earlier accepted value. The C-SL relation at other temperatures is calculated and shown graphically. IN the refining of steel in an acid-lined furnace, it is well known that, unlike in basic refining, a very significant amount of silicon may remain dissolved in the metal even when the carbon content approaches a final endpoint. Further, it is known that the residual silicon increases with increasing temperature. The quantitative relation between silicon and carbon can be calculated for equilibrium conditions from data already available on the Fe-C-O and the Fe-Si-O systems. Such equilibrium calculations could show us approximately the limitations within which the reaction would be expected to operate in practice. In the oxidation of a bath containing both carbon and silicon it is well known that at low temperatures silicon is preferentially oxidized first. It can be shown by calculation that at high temperatures carbon will be oxidized preferentially. It is the purpose of this paper to record direct observations on the Si-C relation by means of experiments carried out in an atmosphere of carbon monoxide for Fe-C-Si alloys contained in silica crucibles. When such a system is brought into equilibrium, at a fixed temperature, the composition of the liquid metal is governed by the following equations: Both K1 and K2 are known with a fair degree of accuracy, and may be calculated from the tabulated In general the percentage of CO2 is extremely small compared to that of CO and in the experiments to be described the partial pressure of the latter was generally only slightly below 1 atm. EXPERIMENTAL METHOD The induction furnace employed was the same as that described by Rist and chipman' and by Fuwa and chipman.2 It was modified slightly in view of the change from alumina to silica crucibles. The small silica crucible was surrounded by a thin susceptor of molybdenum sheet which in turn rested inside a zirconia crucible. Since the zirconia was subject to breakage, it was supported inside an alumina crucible. The charge consisted of 30 to 35 g of electrolytic iron along with the required amounts of refined silicon and graphite to produce a melt of required composition. Purified carbon monoxide and carbon dioxide were passed into the furnace through carefully calibrated flow meters. Two separate and independent series of experiments were carried out. In Series I (D.H.K.) the melt was held in the furnace at 1600°C for periods of time up to 6 hr. Samples were taken at intervals in silica tubes and were analyzed for carbon and silicon. The results of the last one or two samples taken from each experiment and the direction in which equilibrium appeared to be approached are shown in Table I. In Series II (T.F.) the silica crucibles were of less satisfactory strength and the melts were held at 1600° C for periods of only 2 to 4 hr. In heats number 29 to 45 inclusive, the metal was cooled in the furnace and the ingot itself served as a sample for analysis. In heat 46 and all subsequent heats, samples were withdrawn in silica tubes at the termination of the heat, and these samples were analyzed. The results of all of these experiments in which equilibrium appeared to be approached are listed in Table II.

Jan 1, 1965

By J. T. McGrath, R. C. A. Thurston

Poly crystalline specimens of copper, and copper with various additions of zinc, were tested in plane-bending fatigue. In tests performed at a constant stress, the fatigue life of copper increased slightly with the addition of up to fifteen per cent zinc. There was a sharp increase in fatigue life as further additions of zinc of up to 35 pct were made. Surface observations showed that the coarse slip bands that are characteristic of fatigue became narrower as the concentration of zinc increased. The rate of crack propagation also decreased with increasing zinc content. It is suggested that the fatigue behavior is controlled by cross slip processes. CROSS slip occurs when dislocations move from one primary slip plane to another along a connecting or cross slip plane. The primary and cross slip planes have a common slip direction. Wide stacking faults, having low energy, tend to make cross slip more difficult. According to recent theories, the ability of a material to cross slip is important to the formation and propagation of fatigue cracks. McEvily and Machlin2 have examined this concept experimentally by fatiguing single crys tals of lithium fluoride, sodium chloride, silver chloride, and KRS-5.* The latter two materials ex- hibit easy cross slip, while the former two do not. Normal rapid fatigue failure was obtained in the silver chloride and KRS-5 specimens, whereas it was much more difficult to achieve in sodium chloride and lithium fluoride crystals. Furthermore, numerous slip band extrusions and intrusions were found in silver chloride and KRS-5 crystals, whereas only one isolated extrusion was found in lithium fluoride and none was found in sodium chloride. McEvily and Machlin also consider that there is no clear-cut demarcation between crack initiation and propagation. The intrusion-extrusion process, which initiates crack formation, continues ahead of the cracks to allow propagation of these cracks along slip bands. The process of cross slip is therefore important not only to crack initiation, but also to crack propagation. Holden4 postulates that fatigue crack growth is dependent upon cross slip and thus upon stacking-fault energy. Using an X-ray microbeam technique, he found a cyclic subgrain structure in fatigued aluminum and a-iron. Holden suggests that micro-cracks develop in the densely-packed sub-boundaries ahead of the main crack front, and when sufficiently numerous join up to promote crack growth. The ease with which a subgrain structure could form would depend upon the ability of the dislocations to cross slip, and thus upon the stacking-fault energy. Hence in aluminum, which has a high stack-ing-fault energy and in which cross slip is easy, Holden found that the relative rate of fatigue crack propagation was considerably greater than in stainless steel, a low stacking-fault energy material. It has been shown by a number of investigators that the probability of forming deformation stacking faults in copper increases as zinc is added.5-7 Cross slip should, therefore, become more difficult as the zinc concentration is increased. In order to check the validity of the foregoing theories, it was decided to test copper and copper with various additions of zinc in plane bending fatigue, and determine to what extent their fatigue properties are dependent upon their ability to cross slip. EXPERIMENTAL PROCEDURE Fatigue tests were carried out on polycrystalline OFHC copper and various copper-zinc alloys with 5, 15, 20, 30, and 35 wt pct Zn. The Cu-Zn alloys were obtained commercially in sheet form. Test specimens, as shown in Fig. 1, were machined from sheet that had been reduced to an approximate grain size of 0.040 mm, the heat-treatment procedure being similar to that of Feltham anc copley.8

Jan 1, 1963

By Frederick Laist

I AM APPRECIATIVE of the honor you have done me in electing me to membership in your Society. I value the contacts with men of imagination and ideals which this implies. I am grateful for the recognition of such small contributions as I may have made, or helped to make, to the vast fund of scientific and engineering knowledge. We like to think, as we grow older, that our lives have not been purely parasitical, and that through our efforts some forward step, however small, has been taken toward improving conditions under which we live and do our work. In these days of industrial depression, we hear much criticism of our "machine age." Modern engineering, mass production, the complexity of our lives, all come in for some share of blame. The farmer is said to have been spoiled by the tractor and the gang plow, the factory worker has become a slave of the assembly conveyor, the scientific worker is no longer free but has sacrificed much of his individuality to the research organization of which he is a part. We wonder whether our work as engineers has been worth while and whether our striving after more efficient ways of doing things has been a curse to mankind rather than the boon we thought we were conferring.

Jan 1, 1932

By George Harrington

THIS paper is a brief description of the design and equipment of a new coal mine in southern Illinois, which has many features not common practice in shaft coal mining and which is laid out and equipped for such unusually large capacity that it promises soon to become one of the largest mining operations of its kind. Shaft sinking for the mine, New Orient, was commenced in May, 1921, by the Chicago, Wilmington & Franklin Coal Co. In October, 1924, the plant was practically completed and was producing over 6000 tons of coal per day. There is good prospect that within a few years, when the mine is fully developed and manned, the output will attain a daily rate of 12,000 tons. The coal seam at New Orient lies approximately horizontal, about 500 ft. below the surface, and may be said to run from 9 to 12 ft. in thickness. The tendency in Franklin County has been toward large mining units (5000 to 6000 tons per day) with great care being given to protection against fire and explosion hazards, and usually with quite elaborate surface plants permitting careful preparation of the coal into graded sizes comparable with those made in the anthracite region. The field is unionized, with uniform conditions of wages for various classes of work, hours, etc., and the Illinois mining laws are quite specific with regard to fireproofing and safety measures. These conditions make it difficult for any but well-equipped and well-operated mines to meet the competition of the numerous fine properties of which this county can justly be proud. The coal company's property was already developed on the western side by the Orient. mine-a much visited and written about operation (with which many of you are possibly familiar through the Department of Mines' film "The Story of Coal ") which until recently held the 8-hr. production record with 8218 tons and usually ran quite consistently with production of slightly over 6000 tons per day. Experience at Orient was naturally one of the greatest influences in determining the location and character of the New Orient.

Jan 2, 1925

By Yves Dardel

The literature concerning the remelting of alunlinum and its alloys is very rich. Unfortunately the majority of the papers on this subject have no scientific value, for the theories or explanations are too often in opposition to the laws of physical chemistry. Furthermore only a few of the methods of purification are considered in the literature. Hence it has seemed necessary to the author to sketch a general theory of the purification of secondary aluminum. The purpose of the purification is to eliminate the impurities that the charges, and the atmosphere of the furnaces bring into the bath during the successive remelt-ings. Indeed scrap as well as metal can be used when soiled with oil, greases, water, or others, if it has been sufficiently dried and contains oxides. At the melting point of the metal, the oils and greases are decomposed into their constituent elements H², O2, H²O, co², CO, CH,, and others. These gases are added to the corresponding gases in the atmosphere of the furnace. The impurities introduced into the metal during the remelting will accordingly be the products resulting from the action of these gases on the liquid bath. The quantity of hydrogen that is soluble in aluminum and its alloys is given by the relation of sieverts3 as a function of its partial pressure PH2 in the atmosphere m = K vPH² [I] where K is a constant, which depends only upon the temperature and increases with it. The experiments of Rijntgen and Braun4, RÖntgen and M611er5, Bircum-shaw6 and Winterhagerl have rendered it possible to determine the value of K, when the temperature is less than 1.000°C. One obtains: log K = - 4,702.5T + o 238 [2] Besides its usual significance, the term Ph~ represents also the internal pressure of dissolved hydrogen, since in the equilibrium, that is1 when no gas exchange Occurs between the two phases, the Pressures of hydrogen in the metal and in the atmosphere must be equal. Eq I shows that when the partial pressure of H2 increases the amount of dissolved hydrogen in equilibrium increases, and that, if the contrary Occurs, the quantity of H² should diminish. However, if for any reason the diffusion of hydrogen is hindered and the total amount of dissolved gas remains constant while the temperature decreases, the internal pressure of H² increases until it reaches the value of the hydrostatic pressure. At this point, bubbles of hydrogen appear in the bath and escape out of it. The amount of hydrogen in the metal is then limited by a a depending On the hydro- static pressure, which is practically equal to one atmosphere. Indeed hydrogen does not accumulate in the form of a hydride appearing as a separate solid phase. However1 even the mechanism of the solubility is not yet elucidated. One does not know exactly as yet, whether the

Jan 1, 1949

By D. L. Archer, W. W. Owens

Conventional waterflooding often is uneconomic in highly fractured reservoirs because of the gross bypassing of the reservoir oil by injected water. Imbibition and pressure pulse flooding have been used in at least one fractured reservoir in an attempt to achieve better oil recovery performance. This paper presents the results of laboratory flow tests conducted on large cores to evaluate the possible applicability of these methods (particularly pressure pulse flooding) to different types of reservoir systems. Test data were obtained on both water-wet and oil-wet systems, and on systems having two widely different levels of compressibility and flow capacity. Results indicate that pressure pulse recoveries from fractured reservoirs will likely not exceed 5 to 10 per cent pore space with maximum response achieved during the first pulse cycle. Improved recovery by this method is possible from both oil-wet and water-wet reservoirs. Comparable saturation distributions during imbibition and pressure pulse production suggest that an initial pressure pulse cycle to speed production response would not interfere with subsequent imbibition flooding in water-wet reservoirs. INTRODUCTION There is a steady increase in the number of fluid injection projects being initiated each year to improve oil and gas recovery over that obtained by primary production mechanisms. Experience gained in different geographical areas and with different recovery methods is teaching that reservoir anatomy is one of the more important factors controlling the success or failure of such projects. Fractured formations appear to be the rule rather than the exception, especially in carbonate reservoirs. Conventional methods of fluid injection, whether it is waterflooding, gas injection or miscible flooding, have limited applicability to highly fractured reservoirs because of the severe bypassing of reservoir fluids. The result is early breakthrough of the injected fluid and rapidly increasing ratios of injected to in-place fluid with an undesirable effect on return on investment. Thus, innovations to conventional methods must be developed if recovery from fractured reservoirs is to be optimized. One new method proposed for application to highly fractured reservoirs is pressure pulse waterflooding. Although pressure pulsing with gas has been suggested' and rested in at least one reservoir; the Sohio Oil Co. is generally credited with the development and testing of pressure pulsing in conjunction with waterflooding. Publications" of Sohio's waterflood operations in the Spra-berry Trend indicate that the idea for pressure pulse flooding evolved from a critical analysis of the disappointing early performance of their flood initiated in a portion of the trend in April, 1961. This flood was planned to take advtantage of imbibiltion and high pressure gradients across the reservoir matrix blocks (unfractured Mocks of the reservoir rock which are visualized to be generally surrounded 'by the fracture system) evaluated in pilot tests by the Atlantic Richfield Co.5 and Humble Oil & Refining Co.' However, the early recovery and pressure performance of this flood indicalted that high pressure gradients induced between the fracture system and the centers of the matrix blocks were forcing water into the periphery of the blocks and temporarily interfering with the counter-current flow of oil due to imbibition. Fill-up in the blocks was occurring with re-solution of the free gas phase as pressures climbed above the original reservoir bubble point. It appeared that cessation of water injection to permit the capillary forces to become dominant and that expansion of the rock and its contained fluids during pressure reduction might aid in expulsion of oil from the rock matrix into the fractures. Subsequent production performance. aflter cessation of injection, proved this hypotheslis correct. Thus, pressure pulse waterflooding was born. Pressure pulse flooding appears to have several advan'tages over imbibition type flooding in highly fractured reservoirs. First, all wells may be used for water injection which should hasten fill-up and achieve a more rapid increase in reservoir pressure. Second, because of increased injection pressures and rates, flooding gradients will force water into the reservoir matrix more rapidly than would be achieved by imbibition alone. Third, during the pressure depletion cycle of the flood, the compressibility of the system, which has been increased by resolution of the free gas phase, provides energy for the displacement of oil at a rate greater than would correspond to countercurrent flow during imbibition. Fourth, during depletion all wells may be put on production, thus contributing to higher oil withdrawal rates on a reservoir-wide basis. One possible disadvantage of pressure pulse flooding as compared to imbibition floodling, however, is that the outer periphery of each matrix block is flooded to a residual or near residual oil saturation during the Water lnjection stage. This zone of reduced permeability to oil m'ay offer greater restriction to the production of

Jan 1, 1967

By W. S. McCain, B. A. Wilcox, A. H. Clauer

The creep and creep-fracture behavior of a Ni-200-2Th0, alloy has been studied over the temperature range 816° to 1038°C and stress range 4000 to 19,000 psi Specimens having their axes either parallel or transverse to the final sheet-rolling direction were tested in air, and the apparent activation energy for creep was found to be 92 kcal per mole, regardless of specinien orientation. The stress dependence 01- the steady-state creep rate, was satisfied by where n depended on orientation; n = 9.7 for rrzaterial transverse to the rolling direction and n = 24.3 for material parallel to the rolling direction. In the latter case, the relation was also valid. The rupture strength of material parallel to the rolling direction was -1.5 times gveater than the transverse rupture strength. Several tests in vacuum revealed that here the creep rate was higher and rupture life lower than for comparable tests in air. THERE is an increased interest today in producing improved dispersion-hardened alloys for high-temperature structural applications. This had led various materials designers to modify existing alloys, such as thoriated nickel. One system that has received considerable attention is based on chromium additions to Ni-ThO2, with the obvious motive of improving the oxidation resistance. Another effect of chromium is that of lowering the stacking-fault energy, y, of nickel. For example, the addition of 30 wt pct Cr decreases y from -225 erg per sq cm for pure nickel1 to -70 erg per sq cm.' This decrease in y could have several effects on the deformation behavior. There is some evidence that cross slip of dislocations around Tho2 particles is a mechanism of tensile3 and creep4 deformation in TD Nickel (Ni + 2 vol pct ThO2) at temperatures below 0.5 the absolute melting point of nickel, T,. A decrease in ? by chromium additions should increase the difficulty of cross slip. Also it has been suggested that the high-temperature (T > 0.5Tm) rate-controlling creep process in "recrystallized" Ni-Tho2 alloys is the climb of edge dislocations over Tho2 particles.5 According to weertman6 a decrease in the stacking-fault energy should decrease the dislocation climb velocity resulting in a decreased steady-state creep rate. Thus, chromium additions to recrystallized Ni-Tho2 alloys would be expected to decrease the creep rate, all other conditions being constant. However, a difficulty arises when the stacking-fault concept is applied to high-temperature creep of dispersion-strengthened metals which are produced on a commercial or semicommercial scale. This occurs because the materials are processed so that they have a high-stored energy of cold work, and the other substructural effects could obscure any influence of stacking-fault energy per se. An example of an alloy with a high stored energy of cold work is TD Nickel bar. This material has a fibrous grain structure (1 I diam by 10 to 15 p long), and the structure is stabilized by the ThO2 particles. Annealing at high temperatures, e.g., 3 hr at 1300°C, causes no recrystallization or grain growth.4 Previous work by the authors4 showed that the high -temperature creep behavior of TD Nickel could not be related to any simple dislocation theory of creep, and this probably was associated with the complex initial structure of the material.

Jan 1, 1968