Search Documents

By Geo. W. Bain

PRODUCERS of building stone have had to seek new and attractive uses for their output to supplement the diminished orders for standard products. Lunar is the direct result of the need of new outlets for marble and is. probably the most ingenious and attractive type to reach the market in a quarter of a century. It is a highly translucent stone which retains the same glistening sparkle in transmitted light that marble exhibits by incident rays. This sparkle sets it apart entirely from translucencies made of glass or even onyx, alabaster, and the distinctive exceedingly fine textured calcite marbles produced in Alabama and quarried formerly in northern Vermont and Quebec.

Jan 1, 1936

By R. Kerby, T. R. lngraham

The rates of cadmiuln cementation from buffered solutions were studied on both the cylindrical and circular faces of a rotating zinc disk. The activation energies are equivalent on both surfaces, but the rate is more rapid on the cylindrical face. At higher temperatures and at pH values above 6.4, the rate of deposition increases because of an increase in the cathodic area of the deposit. The rate may also be increased by decreasing the thickness of the diffusion layer by rapid stirring. The presence of small amounts of copper, cadmium, lead, iron, or aluminum in the zinc does not affect the cementation rate, but when srnall amounts of copper, cobalt, and arsenic were present in the solution cadmium deposition ceased shortly after it started. Small amounts of copper in solution become cemented with the cadmium to form a coarse deposit of Cd3Cu. When zinc ores containing cadmium are processed for electrolysis, the cadmium appears with the zinc in the leach liquors. Because of the discharge potential of the cadmium ion and the hydrogen overvoltage on metallic cadmium, the cadmium ion must be removed prior to zinc electrolysis to prevent its codeposition. Cadmium is usually removed from acidic zinc sulfate solutions by cementation on zinc. When zinc sheets are used with the appropriate conditions of pH and temperature, a finely divided, high-purity cadmium powder is obtained; it floats to the surface with attached hydrogen bubbles and, after careful washing, may be processed directly to a marketable product.' The reaction on zinc sheets is relatively slow because of the limited amount of exposed cathodic area on the sheets. A much more rapid reaction is obtained when zinc powders are stirred into the solution, but this procedure does have a potential disadvantage: some unreacted zinc may be trapped in the cemented cadmium and thus lower its grade.1 The equilibrium constant at 25°C for the displacement of cadmium by zinc is of the order of lo", which indicates that at equilibrium the displacement would be essentially quantitative and no back reaction need be considered. This indication is not entirely true, however, because in the presence of oxygen any loose cadmium which is out of contact with metallic zinc tends to redissolve after cementation.' The overall effect is much the same as that to be expected if the equilibrium constant were much smaller. Previous experimental work on cementation reac- tions3 is in general agreement that the rates of cementation usually follow first-order kinetics. The metal on which cementation occurs is considered to consist of anodic areas from which metal dissolves and cathodic areas onto which the reactive metal is cemented. For the reaction to continue, the cemented deposit must remain open and porous for the removal of ions. Usually, the deposited metal influences the rate of cementation; when it blocks the pores in the deposit, the rate of cementation will be decreased. Alternatively, when the cemented metal grows as den-drites or as coarse powder the cathodic area is correspondingly increased and the rate of cementation increases,3 Thus, it is only during the initial stages of cementation, prior to the development of deposit effects, that the kinetic behavior of the reaction may be studied without ambiguity. In this paper, experiments will be described for cementation of cadmium from dilute solutions onto the surface of a rapidly spinning zinc cylinder. The effects of ionic concentration, disk rotation speed, temperature, and impurities will be described. APPARATUS AND PROCEDURE The apparatus used for the experiments was described in a previous paper.4 It consisted of a 2-liter vessel in which the contents were protected, against oxidation, by a stream of prepurified nitrogen. The vessel was immersed in a water bath which controlled

Jan 1, 1970

By E. T. Turkdogan

This is a compilation and a critical review of the data on the Fe-Ca-0 ternary system. Using the results on the reductiorz-equilibria, an oxygen potential diagram is drawn for the greater part of the system. A number of univariant systems and invariant points, not determined experimentally, are evaluated by making use of the theorem on univariant curves intersecting at an invariant point. The formation of solid solutions and ternary compounds and the crystal structures of some of the phases in the composition-diagram are given for a feu! temperatures. DURING the past thirty years there has been a continued interest in the study of the Fe-Ca-0 system. A detailed literature survey made by white1 in 1943 indicated that further work was required to clarify the phase relationships; in fact, the work carried out in the subsequent years, reviewed by Burdese2 in 1954, made a valuable contribution to a better understanding of this subject. Most of the data were obtained by the step-wise reduction of mixtures of iron oxides and calcium ferrites. However, there is some uncertainty about the phase relationships in this system, arising mainly from insufficient use of thermodynamic concepts in the construction of phase diagrams. In this paper an attempt is made to establish the invariant points from the available data. OXYGEN POTENTIAL DIAGRAM Schenck and coworkers3,4 were the early investigators who studied part of this system by the step- wise reduction method and suggested the formation of two ternary compounds, CaO.FeO.Fe2O3 and 2Ca0.5Fe0.2Fez03, the latter being referred to as point X. They also deduced from their results that the phases Y (8.74Ca0.32.5Fe0.8.74Fe2O3 and Z (2.02CaO-97.98FeO) were formed near the w?stite corner of the system. Martin and voge15 postulated the existence of the compounds CaO.9FeO and 4Ca0.3Fe3O4; the former is very close to the composition of point Z and the latter to that of CaO.FeO-Fe2O3. The most valuable contribution to the presen knowledge on this system was made by Cirilli and Burdese6-8 who showed by X-ray and chemical anal yses that there were two ternary compounds, CaO-Fe0.Fe2O3 and CaO.3FeO-FezO3; the former is the same as that suggested by Schenck et al. and the latter is close to their point X. The results of Cirilli and Burdese show that the phases Y and Z postulated by Schenk et al. are solid solutions of calcium oxide in w?stite. In most of the above-mentioned reduction-equilibria measurements carbon monoxide-carbon dioxide mixtures were used and in a few cases hydrogen-water vapor mixtures were employed. Using the

Jan 1, 1962

By T. D. Thomas

CONTENTS PAGE T. D. Thomas-Misfires in Anthracite Coal Mines 3 W. H. Forbes-Misfires in Bituminous Coal Mines 12 A. W. Worthington-Misfires in Non-metallic Mining (Limestone) 18 Misfires in Anthracite Coal Mines BY T. D. THOMAS,* LANSFORD, PA. (New York Meeting, February, 1929) IN THIS paper, major attention is given to misfires in mines where electric multiple shot-firing is the system used. Misfires are sometimes caused by one action or condition and at other times by a combination of two or more. They may be divided into two classes: (1) those caused by workers in the mines, (2) mechanical or manufacturer's causes. The second cause will be discussed first. MISFIRES CAUSED BY FAULTY DETONATORS The important part of an electric blasting cap, to the user where multiple shot-firing is done, ass in the steep-pitch, thick-vein, anthracite mines, is the bridge wire. In single shot-firing this factor is not apparent, but in mines where multiple firing is done any variation in the resistance of the bridge wire, where full or even rated battery capacity is required, will most likely cause a misfire The reason for this is obvious. If the resistance in the bridge wires is not the same, some of the detonators will fire because of their greater comparative resistance. Variance in resistance of bridge wires is caused by a slight difference in the diameter of the bridge wire, also to a difference in the composition of the bridge wires. Again, where the bridge wires have become rusted, there will be a variance in resistance. About the year 1922, one of the large coal companies was greatly alarmed by the number of serious and fatal accidents caused by misfires. The general manager issued an order that these accidents must be greatly reduced, and if possible, entirely prevented.

Jan 1, 1929

By W. A. Backofen, D. Lee

Titanium of commercial purity (RC-70) and two all-a (hcp) alloys (4Al-1/4O2 and 5Al-2.5Sn) were tested in sheet form under conditions of combined-stress loading. Plane-strain compression and plane -strain tension together with uniaxial compression and tension provided information for constructing the tension-tension and compression-compression quadvants of the plane-stress yield locus. Coordinate values were obtained from yield-strength measurements; the slope at each point was based on a plastic-strain ratio. The materials represented a wide range of plastic anisotropy, which was reflected in correspondingly varied departures of the yield locus from that for iso-tropy. The tension-tension and compression-compression quadrants were not identical. If the uniaxial yield strength is insensitive to direction and the sign of the applied stress, the Mises or perhaps the Tresca criterion is adequate for predicting the onset of yielding under combined-stress loading. The prediction is not so straightforward in plastically anisotropic material. Depending upon details of texture, combined-stress yielding resistance may be substantially different from that indicated by the usual criteria.' However. a continuum theory of yielding under such conditions is available for reasonably direct application.2,3 Whether or not it can be used successfully must, of course, depend upon how closely the conditions of the theory are satisfied in the material in question. In its present form the theory contains no provision for Bauschinger-type effects, nor does it allow for the consequences that might grow out of deformation by more than one mechanism, e.g., by slip and twinning.4 With those limitations, more importance must be attached to experimental information about the yield surface for anisotropic materials. Studies of the yield surface have generally been confined to states of plane stress (tension-tension and tension-compression) established in thin-wall tubes by externally applied forces and internal pressure. That approach would be entirely suitable for anisotropic materials if they were available in tube form or in sufficient bulk to be machined into test specimens. 6-9 It would not serve for the textured and anisotropic sheets of much current engineering interest, unless sheet could be formed into high-pressure tubing without structural change. Since there would seem to be little chance of the latter, practical alternatives are needed. One such alternative is the subject of this paper. It involves the use of a few selected but relatively simple uniaxial loading tests on sheet specimens. The underlying idea is presented here with some details relating to application and a few results bearing on how well it has worked. THE BASIS OF TESTING Conventional Measurements. Yielding for a general case of anisotropy is described by the plane-stress locus in Fig. 1. Reference directions in the sheet specimen are related to the stress coordinates as shown with the insert: x is the rolling direction, y the transverse direction, and z the through-thickness direction. The four reference-direction yield strengths (t, tension; c, compression), Xt, Xc, Yt, and Yc, are all different. Nine paths that can be followed in uniaxial loading experiments are identified. Paths 1, 2, 3, and 4 represent conventional tension and compression testing to establish Xt, Yt,.Xc, and Yc. Useful information also comes from the ratio of the transverse plastic-strain components associated with yielding and flow in conventional tension or compression. A condition to be satisfied in locus construction is that the plastic-strain vector be everywhere normal to the locus.10 The projection of the vector which would

Jan 1, 1967

By Sir Robert Hadfield

LAST year this Institute was good enough to accept some remarks by the writer regarding sound steel, entitled Plant for Hadfield Method of Producing Sound Steel Ingots, being a continuation of a research in which for some time the writer has been engaged, and full particulars of which were submitted in papers entitled A New Method of Revealing Segregation in Steel Ingots, and Method of Producing Sound Ingots, read before the Iron and Steel Institute in October, 1912. These papers gave rise to a very interesting discussion, both in England and America. This question is one of vital importance, as unless sound steel in the form of ingots is first obtained, sound steel in the finished forms of rail billets, rails, bars, sheets, and other forms cannot be expected. The working stresses demanded by modern conditions are so great, each year they probably approach nearer to the limit of safety, that without doubt those who produce steel will be compelled to pay the attention which this subject deserves. Moreover, the problem is not an insuperable one, as shown by the writer in the papers above referred to. In view of the information which has already been presented in these papers, it is not now necessary to go into details of the system advocated by the writer, except to repeat that the ingots and steel now referred to were produced by employing in the first place sound fluid steel, free from blowholes, this being poured into ordinary ingot molds, provided with the necessary feeding heads, the insulating slag medium, also charcoal and air blast or other suitable form of applying heat to the head portion of the ingot. Tile upper or head portion of the ingot is kept fluid by the intense heat generated by the air blast and charcoal, so that such fluid steel passes into the body of the ingot below the head, thus feeding and avoiding the shrinkage or piping which would otherwise occur. The result is the production of a sound steel ingot, free from blowholes, segregation and piping, and in which the waste portion, usually termed the discard, is but little over 7 or 8 per cent.

Jan 4, 1914

By G. J. Dickman, W. N. Thomas

The factors involved in selecting, a drive system for a grinding mill, including gearing arrangement, motor selection, and electric-supply system limitations are reviewed. Equipment costs are evaluated on a dollar per horsepower basis and starting performance is analyzed, the latter making use of a recently developed computer program. The present interest in large-diameter grinding mills and the rapidly rising cost of the drive in proportion to the cost of the mill establishes a need to explore the drive system in detail. The drive for a 7 to 8,000 hp mill will cost from $350 to $600,000 which represents nearly half the total cost of the mill package, and requires as much building space as the mill proper. Some of the drive components require a longer time to manufacture and the installation time and costs are equal to those for the mill. It is apparent that the drive has become a dominant factor in the overall mill design consideration. A new plant requires a tremendous investment in both time and money. With the high degree of competition in the mining industry, low capital cost is an exceedingly important factor in the development of a project. It is just as important, however, to insure that the equipment is going to perform satisfactorily for the anticipated life of the project without adding unplanned operating, maintenance, and replacement costs. This is the position in which the engineer or designer usually finds himself and is really one of his primary functionsestablishing a realistic compromise between cost and performance. Large primary grinding mills can represent a major portion of the cost of a plant and the drive system accounts for a substantial part of this cost. These facts justify a careful analysis of the drive requirements and all of the factors involved in ultimately arriving at the best system for the lowest cost. A number of excellent papers have been published on various aspects of mill drives. The authors have used information from these papers in making a study of a drive for a 7600-hp, 32 x 12-ft autogenous mill. This was a broad investigation, including mechanical and electrical design, layout, performance, and maintenance considerations, and overall economics leading to the selection of the optimum system for that mill. This paper was developed from the study and includes information applicable to large mills in general. For a successful and economical application, the drive must be considered as a system and all of the components analyzed to determine their effect on the system. This requires the participation of the mill designer, gear, and other mechanical component manufacturers, motor manufacturer, plant designer, and operator. A careful analysis of the mill torque requirements is first necessary to provide a basis for selection of the mechanical and electrical drive components. Because of manufacturing limitations on the size and capacity of gearing available for these low-speed applications, an evaluation of costs for various gear ratios and configurations in conjunction with motor speeds is required. Consultation with the power-supply company is necessary to determine limitations on motor-starting disturbances and to analyze operating costs on the basis of existing rate structures and low characteristics. Finally, consideration must be given to the drive arrangement and its affect on plant layout, space requirements, and location of auxiliary equipment for the selected process. There are presently three basic schemes for driving a mill. The first is a direct drive by a motor operating at mill speed with no gearing. The second is by a higher-speed motor through a trunnion-connected gear drive. The third is by a motor through the more conventional pinion and ring-gear with the option of an interposing gear box to permit greater motor speed than pinion shaft speed. [(Fig. 1.)] Several manufacturers have or are presently developing motors which drive the mill directly without the use of gears. One arrangement has the motor armature intimately surrounding the mill shell-discharge spout or extension of the trunnion journal. The motor stator is then supported independently and surrounds the shell or trunnion-mounted rotor. Another variation utilizes an independent mill-speed motor connected to the trunnion by a drive shaft and flexible couplings.

Jan 1, 1972

By Hsun Hu

C. G. Dunn (Geneva1 Electvic Reseavclz Labo,vatory)-Dr. Hu16 has obtained a number of rolling and annealing texture results that partly agree with those of Dunn17 and Dunn and Kohl8 for experiments of a similar nature. I would like to discuss some of the points of agreement as well as some of disagreement and then present some unpublished data as a contribution to the work on textures. Firstly, there is agreement on the components produced during a 70 pct cold-rolling reduction of a (110) [001 ] single crystal; there is agreement on the forma- tion of a (110) [001] recrystallization texture provided recrystallization occurs at 800°C or higher; and there is agreement on the formation of (120) [001] components provided recrystallization occurs below 600°C. There is some disagreement on the low-temperature recrystallization since I also obtained a substantial amount of a (110) [001] component while the author obtained only (120) [001] components. I also discussed the differences between low- and high-temperature recrystallization (which included further annealing changes in the samples on long

Jan 1, 1962

By C. Bezemer, I. Havenaar

An investigation was carried out on the dynamic liltration behavior of drilling fluids. In a set-up consisting of a porous pipe through which the drilling mud was circulated, dynamic liltration rates and cake thicknesses were determined as a function of flow rate and filtration time. Eventually, a state of equilibrium was reached; i.e., both cake thickness and filtration rate attained constant values. Concurrently, dynamic filtration tests were carried out in a simple dynamic filter apparatus where mud flow was similar to that in a rotational vismmeter. In both arrangements the relation between equilibrium liltration data and rate of shear at the cake surlace was studied. Filter pipe and dynamic filter apparatus were lound to give identical relations. It was therelore concluded that the latter apparatus, which is suitable lor routine measurements on small amounts of mud, could be used to determine the dynamic liltration behavior of mud under borehole flow conditions. Some data are presented on the effect of filtration pressure and temperature on equilibrium filtration rate and cake thickness. INTRODUCTION In oil well drilling, the drilling fluid used generally forms a mud cake on the permeable sections of the borehole wall while filtrate is lost into the formation. As to the conditions under which this filtration process takes place, a distinction should be made between static mud filtration (mud is not circulating) and dynamic mud filtration (mud is circulating). In recent years several investigatorsl-5 have studied the process of dynamic mud filtration about which little had previously been known. This type of filtration is the subject of this paper which confirms several findings of previous investigators. It differs from already published works, however, in the following respects. 1. It contains a description of a simple laboratory apparatus developed for dynamic filtration measurements on small amounts of mud. 2. The effect of rate of shear at the cake surface on dynamic filtration has been studied. As a result of this study, dynamic filtration data pertaining to the borehole conditions of mud flow can be found from laboratory tests. 3. Some data are presented on the effect of filtration pressure and temperature on dynamic filtration. The work was limited to a small number of muds. No attempt was made to compare data on API filtrare loss with dynamic filtration rates. Previous workers have clearly shown that no correlation exists between static and dynamic filtration rates. EXPERIMENTAL ARRANGEMENT To establish whether the effect of mud flow conditions on dynamic filtrations is governed by the rate of shear at the cake surface, two different types of mud flow were used. In this connection the experiments were partially conducted by means of a porous pipe through which mud was circulated, partly in a dynamic filter apparatus which somewhat resembles a rotational viscometer. In both cases the flow conditions of the mud were well defined, thus making it possible to-calculate rates of shear at the cake surface. The filter pipe was 200 cm long with an internal diameter of 3 cm. Its perforated wall was covered on the inside with filter cloth on which the mud cake could form. Mud was pumped through the pipe at linear rates varying from 20 to 186 cm/sec. The required filtration pressure was obtained by means of a lack-pressure valve downstream of the filter pipe. In this arrangement the type of flow existing in the borehole is reasonably well simulated. The dynamic filter apparatus (Figs. I. and 2) consists mainly of two concentric cylinders with a clearance of about 0.5 cm. The outer cylinder (rotor) can be rotated at rates up to 1,000 rpm. The outer surface of the inner cylinder (radius about 2.5 cm) is covered with filter cloth or paper supported by copper gauze. The two cylinders are mounted inside a pressure

Jan 1, 1967

By Clarence Woods

ONCE a millionaire's plaything, the Santo Domingo mine, in Peru, is now, because of its metallurgical problem, an engineer's nightmare. It is deep in the montaña jungles of the Amazon basin, 140 mi. northeast of Tirapata, which is a rail- way station between Puno and Cuzco, and about 250 mi. east of Mollendo on the Pacific. The discovery was 111ade by Marian(-) Quispe, an Indian, who, while searching for quinine bark, was attracted by a slab of gold quartz 1x1 the rock wall of a narrow canyon. He broke off a piece, weighing 47 Spanish ounces and, that time, worth approximately $900. This he took to Francisco Velasco and Manuel Estrada, merchants of Coaza, who persuaded Quispe to lead them to the place, five days' journey on foot through a tangled wilderness. Velasco ' and Estrada denounced the claim

Jan 1, 1938

By D. F. Kelsall

The hydraulic cyclone, in simple or modified form, is finding increasing application in metallurgical processing. In this article, the author considers several aspects of conventional applications, less conventional applications and some potential uses of modified cyclones. Information concerning the mechanism of separation within a cyclone and the effect of the major variables is summarized. During the past twenty years, and especially in the last decade, hydraulic cyclones have found increasing application in metallurgical processing as classifiers and, under special circumstances, as thickeners. To a more limited extent cyclones have been used to extend heavy, or dense, medium separation into the finer size ranges, and several attempts have been made to separate dispersions of immiscible liquids with a view to use in the field of liquid-liquid extraction. A large proportion of published work reports incomplete data, applicable only to particular systems. The more useful papers, covering data of relatively wide significance, have been reviewed recently in considerable detail1,2 and no attempt will be made to cover the same material in the present paper. However, before considering several aspects of conventional application, less conventional applications and some potential uses of modified cyclones, it is considered pertinent to summarize information relating to the mechanism of separation within a cyclone and the effect of the major variables. LIQUID FLOW PATTERNS At any point within a simple cyclone the liquid velocity may be resolved into three components, i.e., the tangential or swirling velocity (v), the vertical velocity (w), and the radial velocity (u). The relative values of these components at selected positions within a typical cyclone have been established for water. 3 The extent to which similar flow patterns exist in systems of considerably higher viscosity, or apparent viscosity, operating under conditions of reasonable pressure drop, is not known with precision, but indirect evidence indicates that up to approximately five centipoise there is no marked change. Beneath the bottom of the vortex finder, envelopes of constant tangential velocity are cylinders coaxial with the cyclone, and, at any horizontal level, starting from near the conical wall, this component of velocity increases with decrease in radius (r) according to the relationship vrn = constant (where 0 < n < 1) This holds to regions near the center of the cyclone where v reaches a maximum value at a radius somewhat smaller than that of the inside wall of the vortex finder. At this point, the centrifugal acceleration, v2/r reaches a maximum value. As the radius is further decreased the tangential velocity decreases so that v = r. Above the bottom of the vortex finder there is a tendency for the first relationship to persist to near the outside wall of the vortex finder, until v reaches a maximum and then decreases rapidly as the wall is approached. The two most significant features of the vertical velocity distribution are an approximately conical Table I. List of Symbols v = liquid tangential velocity at any point in the cyclone w = liquid vertical velocity at any point in the cyclone u = liquid radial velocity at any point in the cyclone r = radius from cyclone axis to any point ? = half angle of conical portion of the cyclone ?= fluid viscosity d = particle diameter s = liquid specific gravity p = particle specific gravity d50 = the particle diameter which distributes 5090 to overflow, 50% to underflow e = overflow diameter, in. b = feed diameter, in. G = gpm of feed slurry

Jan 1, 1963

By T. E. Seidel, A. U. MacRae

The dependence of the electrical and crystalline properties of silicon containing ion implanted boron atoms have been studied as a function of the incident dose, substrate temperature, and annealing tempera-ture. Hall effect studies show that the compensation due to defects is negligible after annealing at and above 500°C for a dose of 1013 ions per sq cm. Steps occur in the isochronal annealing curve for the sheet resistance at 300°C and 800°C and the mechanisms responsible for these steps are discussed. The range of the ions at 150 kev is 3500 * 5001. Electron diffraction studies on samples implanted with 150 ker ions show the existence of damaged (polycrystalline) silicon closer to the surface than the range of the ions. Etching and subsequent annealing of etched and unetched specimens suggest that the poly crystalline silicon is closer to the surface than the bulk of the distribution of ions. THE purpose of this study is to investigate some electrical and crystalline properties of ion implanted boron in silicon. Sheet resistance, Hall measurement, depth distribution by chemical staining, thermal probe and electron diffraction have been used to study the properties of samples implanted in a random direction with ions having energy up to 150 kev. The boron-silicon system has been the subject of considerable study&apos;-7 due to its possible application in the fabrication of electronic devices. The implanted ions produce considerable crystalline damage to the substrate crystal before they lose most of their primary energy and come to rest. Fortunately, most, if not all, of this damage can be removed by subsequent annealing or by holding the substrate at an elevated temperature during the implantation process. Sheet resistivity measurements of the p-type layers produced by boron implantation into room-temperature silicon, reveal that the annealing occurs in a two-step process: the first occurring at -300°C and the second at -800°C.&apos; Electron-microscope and low-angle electron diffraction studies of this damaged material indicate that the bombarding ions produce an amorphous silicon region about the trajectory of each ion.&apos; At high doses, these damaged regions overlap and an amorphous surface layer results. Furthermore, the 800°C annealing step, appears to be associated with the elimination of this gross damage. The depth distribution of the as-implanted and also the annealed samples have been studied by an angle lap and staining technique as well as by Hall measurements.3-7 We find the experimentally determined ranges of the boron are less than those calculated by the Lindhard-Scharff-Schiott theorys (hereafter referred to as the LSS theory). Our results are in essential agreement with pre- vious results. In addition, we have made Hall measurements on samples bombarded with a low dose (2 x 1013 ions per sq cm) to minimize impurity banding effects, and find that deep ionized levels influence the carrier concentration and room-temperature hole mobility until the sample is annealed at temperatures above 500°C. Above this temperature, the data corresponds to that obtained when silicon is doped with boron by conventional techniques. We have also made a depth distribution determination of the crystalline damage due to the implanted boron by using glancing angle electron diffraction techniques. It was found that the gross damage depth distribution of heavily implanted samples is closer to the surface than the depth distribution of the electrically active boron. By removing this gross damage, without affecting the distribution of the implanted boron, we have determined that the 800°C annealing stage is not exclusively due to the improvement in the crystalline perfection of the amorphous material but also appears to be associated with the annealing of some point defects. These results and their relation to previous results are discussed in the following sections. IMPLANTATIONS Boron ions were implanted into silicon samples using an accelerator capable of operating from 10 to 150

Jan 1, 1970

By J. E. Powell, F. H. Spedding

WHILE rare earths are reported to be widely distributed in nature and are not really rare," in practice, there are only a few minerals which are sufficiently rich in rare earths to serve as practical sources. Perhaps the best known of these is monazite which is a phosphate mineral containing rare earths and thorium. This mineral occurs as a dense brown sand in gravel beds and is particularly rich in the light rare earths of the cerium subgroup. This mineral is processed commercially for its thorium, cerium, and lanthanum content, and, consequently, furnishes rich concentrates from which neodymium, praseodymium, samarium, europium, and gadolinium may be obtained. Unfortunately, monazite is rather lean in rare earths heavier than gadolinium. A second mineral which is rich in the light rare earths is bastnasite, a fluoro-carbonate. Extensive deposits of this ore have been discovered in the western United States and have received considerable newspaper publicity in recent years. While bastnasite is very rich with respect to cerium, lanthanum, and neodymium, it contains even less heavy rare earths than does monazite. One of the better sources of heavy rare earths of the yttrium subgroup is gadolinite, a black silicate rock from which the rare-earth content can be extracted readily by acid leaching. It is obtained chiefly from Norway at the present time, although there are known deposits in the United States. Other sources of heavy rare earths include fergu-sonite, euxenite, and samarskite which are refractory tantalo-columbate ores. These minerals require caustic fusion or reduction to carbides with carbon before the rare-earth content can be extracted. All of the minerals which are rich in the heavy rare earths contain yttrium as a major constituent. After the rare earths have been extracted as a group from an ore by chemical means, it is generally convenient to precipitate them from acid media with oxalic acid in order to eliminate certain non-rare-earth impurities such as iron, beryllium, etc., which are usually present. The oxalate can then be readily ignited to R2O3. The oxide can be dissolved in acid and is the starting point for subsequent separation into the pure components. Perhaps the principal reason why the rare earths have not been studied as extensively as other elements of the periodic table, whose natural abundances are comparable, is that they are extremely difficult to separate from each other by the usual chemical means. Prior to 1945, the separation of one trivalent rare earth from another was a laborious process. All separations were based on repeated fractionation processes, i.e., fractional precipitation, fractional decomposition, fractional crystallization, etc. These processes were repeated from a few hundred to many thousands of times in order to obtain individual rare-earth salts of reasonable purity. Of course, mention should be made that, in the few cases where a rare earth could be oxidized or reduced to a valence state other than three, more conventional chemical means could be utilized to separate the oxidized or reduced ion from the other normally trivalent rare earths. The ionic states which deserve special mention are CeIV, SmII, Eu11, and Yb11. When it is possible to remove an element of the series efficiently, due to an optional valence state, its immediate neighbors also become easier to isolate. For example, binary mixtures of lanthanum and cerium, and praseodymium and cerium can be obtained by a relatively small number of fractional operations. The tetravalent state of cerium then allows the complete resolution of the binary mixtures by ordinary chemical means. Although the tetravalent state of cerium has been known for a long time, the divalent states of samarium, europium, and ytterbium were not used extensively in separations prior to 1930 because they are relatively unstable in aqueous media.&apos;-" No attempt will be made to give a comprehensive review of the extensive literature dealing with the separation of rare earths. Rather, this paper will be confined to a review of those methods which have been developed at Iowa State College during recent years, and which have proved extraordinarily successful for the isolation of highly pure rare earths in quantity. It was obvious that, if pure rare earths were to become generally available, methods would have to be developed wherein the thousands of fractional operations made necessary by the similarity of rare-earth properties could be performed automatically. The development of chromatographic techniques and ion-exchange resins appeared to offer a mechanism by which this objective could be accomplished. A number of early attempts were made to separate rare earths by these means; for example, Russell and Pearce12 passed a mixture of rare earths through a cation-exchange column and reported

Jan 1, 1955

By Paul Foote

The temperature of a material may be ascertained by measurement of the intensity of the radiant energy it emits. This measurement may refer to the radiation of all wave lengths emitted by the material, or, if the material is glowing, the measurement may refer to the visible light emitted, or to the radiation in n very restricted portion of the visible spectrum. In general, the intensity of radiation depends not alone upon the temperature of the source, but, also upon its nature. Thus, glowing carbon appears to the eye about three times as bright as glowing platinum, at the same temperature. This is technically expressed by saying that the emissive power or emissivity of carbon is about three times that of platinum. A material having the highest theoretically possible emissivity is known as a "black body;" it is customary to assign a numerical value of 1 to the emissivity of a black body. A black body is experimentally realized by uniformly heating a hollow enclosure and observing the radiation coming from a small opening in the wall. The intensity of radiation emitted from this opening depends only on the temperature of the walls, and not on the material of which they are constructed. If E is the emissivity of any non-transparent material and R is its reflection coefficient, it can be shown that E + R, = 1. If a material having an emissivity of, say, 0.40, and hence a reflection coefficient of 0.60, is placed inside a black body it becomes indistinguishable from its Surroundings, because the total intensity of radiation leaving the material is the same as that emitted by the black body. While the material actually emits only 40 per cent of the intensity of a black body at the same temperature, 60 per cent. of the radiation falling upon it from the walls of the enclosure is reflected. However, if the material is removed from the black body and placed in the open air, the reflected intensity is no longer present and the object appears but 40 per cent. as bright as a black body at the same temperature.

Jan 8, 1919

By R. W. Cahn, C. D. Graham

The rate of growth of a single grain growing into a strained aluminum single crystal, measured by the conventional heat-cool-etch technique, is shown to decrease with time at temperature. The growth rate measured by means of X-rays, with the sample continuously at temperature, is found to be linear. Evidence is presented to show that the decreasing growth rate obtained by the conventional technique is due to abnormal recovery in the strained grain, and that the recovery in turn results from the heating and cooling cycles, rather than from the effects of etching. The experimental apparatus is described in an appendix. FREQUENTLY, the rate of grain boundary motion during recrystallization is determined by heating a sample to a known temperature for a given time, cooling to room temperature, and etching to reveal the boundary position. The cycle of operations is repeated as many times as necessary to establish the rate of boundary motion. Although this heat-cool-etch technique has been used by a number of workers over a period of many years,&apos;-!&apos; other investigators have encountered difficulty with the method."&apos;. " They have attributed the erratic results to the effects of repeated heating and cooling, or of etching, or both, and have adopted an alternative experimental procedure in which a number of identical samples are employed, each sample being cooled and etched only once. This alternative method ove1.comes some difficulties, but introduces others. In particular, the incubation periods of the observed grains are unknown: any effect of crystal orientation on growth rate cannot be determined easily. A preferable method would be to measure the motion of a recrystallizing grain boundary with the sample at temperature without etching," but such measurements have in the past been restricted to nonmetals. This paper describes the construction and operation of a device, the goniometer furnace, with which the position of a moving grain boundary between a recrystallizing grain and the strained single crystal into which it grows can be measured by means of X-rays, with the sample maintained continuously at temperature. Goniometer Furnace The operating principle of the goniometer furnace is shown in Fig. 1. The sample, in the form of a bicrystal strip, is surrounded by a furnace, not shown in the sketch, and can be rotated about the two axes A and B which intersect at the point where the X-ray beam strikes the strip. The strip is oriented so that one of the two grains gives a strong Bragg reflection, which is detected by a suitably placed Geiger-Miiller counter coupled to a counting-rate meter When the strip is moved parallel to its own length in the furnace, arrow C, so that the X-ray beam strikes the second grain, there is in general no strong reflection. By noting the position of the strip at which the drop in Geiger counter reading occurs, it is possible to determine the position of the boundary. Measuring the change in boundary position with time at temperature gives the rate of growth of the recrystallizing grain. Details of the construction and operation of the goniometer furnace are given in the Appendix. Measurements showed that the temperature in the furnace was uniform within ±10°C over its working length of about 28 cm. The temperature at the measuring position, i.e., at the point where the X-ray beam struck the sample, was estimated to be constant within ±2oC. Using the goniometer furnace, the position of a stationary boundary could be measured with a reproducibility of ±0.3 mm. At elevated temperatures, 500" to 625"C, with the boundary in motion and the X-ray reflection less sharp, the estimated accuracy of each measured boundary position dropped to about ±1 mm. Experimental Results The test pieces were single crystals of 99.6 pet A1 —principal impurities 0.19 pet Fe and 0.12 pet Si— 1 mm by 1 cm in cross section and 6 to 10 cm in length, grown by the strain-anneal method. This relatively low purity material was used because of the difficulty encountered in producing strain-anneal single crystals of very high purity—99.996 pet—

Jan 1, 1957

By J. A. Putnam, A. D. K. Laird

In laboratory research on the behavior of oil, gas and water in porous materials, no direct method has been devised to measure saturation without disturbing the flow. Indirect methods involving various forms of radiation have been developed for measuring one or two components. The X-ray absorption method for two components has been described previously1-3. The possibility of three component measurement has also been mentioned1. Since two component measurement still requires considerable care to insure accuracy, the fact that three components can be measured satisfactorily is not generally appreciated. The fraction of the energy of an X-ray beam of one wavelength transmitted through a material is given by the transmission factor. in which 1 is the beam&apos;s path length through the fluid. p is the fluid density, and 1,. is its mass absorption coefficient. Eq. 1 implies that all parts of the beam pass through equal amounts of the fluid. Practical applications are, therefore, limited to systems in which the fluid is distributed so that I varies negligibly over the cross-section of the beam. Typical variations of the transmission factor with X-ray tube potential arc shown in Fig. 2 from which experimental points have been omitted for clarity. The X-ray absorption of low pressure gases in a core is practically zero so it cannot he distinguished from that a vacuum by instruments that will differentiate between liquids. The transmission factor of a gas in a core is. therefore, unity. Consequently, the saturation of only one gaseous component can be found. If two fluids completely fill a core, their two saturations add to unity and, therefore, only one value of the transmission factor, T, is needed to determine both of them. When two liquids do not completely fill the core, their saturations do not add to unity and transmission factors at two wavelengths must be measured. At one of these wavelengths, 7 for one liquid must be different from T or the other liquid. The change of T for one liquid us the wavelength is changed between the two values must be different from the corresponding change of T in the other liquid. The two values of fluid saturation will also give that of the gas because the three saturations must add to unity. In Fig. 2 it can be seen that there are many large differences of T between various oil solutions and water solutions at any one potential, and between potentials for any one solution. Consequently, conditions for optimum accuracy of measurement of the saturations of a gas and two liquids can be chosen. Once the operating potentials have been selected, however. it is more convenient to cross plot the data from Fig. 2 on transmission factor-solution concentration coordinates for the chosen potentials, as shown in Fig. 3. Fig. 3 was used to plan the experimental procedure for Core N-38-1. Since the voltage control at 45 kv was good, the slopes of the curves in Fig. 2 at this potential would cause little error. At low potentials, however, the voltage control was not good, so 33 kv was chosen because the small slopes of the curves made voltage control less critical. The lowest strength beam that could be measured reasonably at 33 kv corresponded to a minimum T factor of 0.385. Fig. 3 shows that both 4.80 weight per cent of cadmium chloride in water and 24.0 per cent of iodobenzene in crystal oil had this T value, and, consequently, were indistinguishable to the X-rays at 33 kv. Thus, at 33 kv, the liquid saturation was given by the same curve regardless of the relative amounts of oil and water solutions present. This simple calibration curve from which the gas and liquid saturation can be read, is shown in Fig. 4. Fig. 3 also shows that at 45 kv, T for the aqueous solution is 0.610. and that T for the oil solution is 0.220. These values were transferred to Fig. 4 to give the triangular calibration plot from which the brine and oil saturations can be found, after the gas saturation has been determined at 33 kv.

By K. K. Clark

Excessive injection pressures in water injection wells may create deeply penetrating fractures, or may open up existing reservoir fractures. If these fractures are oriented toward offset producing wells, oil recovery at injected water breakthrough and ultimate recovery will be impaired. A method of calculating fracture lengths from pressure fall-off test data is presented. The method is based on a linear flow model that simulates conditions present during the early-time period after shutting in an injection well. Fracture lengths can be calculated directly if formation permeability is known. A graphical technique is presented that provides fracture lengths based on permeabilities calculated from normal fall-off tests, where those permeabilities are adjusted for flow geometry. Test data from four injection wells and results obtained from applying the method to these wells are discussed. Introduction Rates of water injection into nonstimulated wells in low permeability reservoirs frequently fall below economically desirable levels. Therefore, some form of stimulation such as hydraulic fracturing often is performed on these wells. Usually these fractures penetrate a short distance from the well — short as compared with interwell spacing — and therefore should not create problems of water channeling to offset producing wells. In the past, some operators have been tempted to increase injection pressures continually to maintain a specified injection rate. But pressures cannot be increased indefinitely. Field data indicate that continued injection above fracture opening pressure can cause excessively long fractures to approach between well distances. If these long fractures intersect or closely approach offset producing wells, premature water breakthrough can result. It is difficult to seal effectively these fractures by various workover procedures after premature water breakthrough has occurred. This paper describes testing procedures that are potentially capable of detecting premature water breakthrough before it occurs. Knowledge of fracture lengths and fracture opening pressures can assist field engineers in selecting optimum operating conditions for water injection wells. Fracture lengths should be calculated from pressure fall-off tests on injection wells, and maximum permissible iniection pressures should be determined from step-rate injectivity tests. Equipped with this information, the field engineer is in a better position to recommend for a particular injection well the optimum operating conditions that will lessen the chances of channeling to offset producers. Historically, pressure transient tests have been conducted primarily on producing wells and analysis procedures have been based on radial flow concepts. Several authors have suggested that these same procedures be applied to tests conducted on water injection wells. This application is justified for wells that are not connected to extensive fracture systems. However, if the formation is severely fractured, the interpretation methods must be modified. Several authors have presented the pressure response of various systems that are intended to simulate reservoir conditions. A paper by Russell and Truitt* on vertically fractured svstems is probablv the most useful from the standpoint bf the fieid engineer. Russell and Truitt presented the pressure-vs-time behavior of a well connected to vertical fractures with various fixed lengths. Their permeability adjustment technique is used in this paper to refine methods of calculating fracture length and interwell permeability. Theory and Definitions Three flow-system geometries are considered in analyzing injection well test data. These various geometries are applicable during specific time intervals of transient pressure tests. Schematic drawings of the flow models, and the time intervals over which they are applicable, are shown in Fig. 1 in the chronological order that they are applied to the pressure response of water injection wells in fractured formations. The very early response is simulated by an infinite linear system as shown in Fig. 1A. This representation permits the calculation of matrix surface area exposed to the fracture. The model shown in Fig. 1B is identical with the one studied by Russell and Truitt. They evaluated the transient pressure response of this vertically fractured system by finite difference techniques. The results were presented as tabulations of dimensionless pressure drop functions for a range of fracture lengths. A semilog plot of these data shows that the apparent matrix permeability can be related to the true matrix permeability by a simple exponential function. Their adjustment factor is used in this paper to improve the accuracy of matrix-permeability and fracture-length calculations.

Jan 1, 1969

By Leonard D. Jaffe

In recent years, the advantages of tempered martensite as a microstructure for steel parts have been well established. For parts that must not fracture brittlely when loaded at high rates, at low temperatures, or under conditions of combined stress, tempered martensite is especially desirable. One of the factors that determine whether a steel part will have a martensitic structure after heat treatment is the hardenability of the steel. Despite the large amount of recent research, there are still many unsettled basic questions concerning hardenability and its relation to chemical composition, and, indeed, considerable disagreement among investigators in the field. Much of the uncertainty that beclouds the existing knowledge of hardenability arises from the fact that hardenability is still a wholly empirical concept, and has not been quantitatively related to the more fundamental knowledge of isothermal decomposition of austenite. Hardenability is, essentiaily, a measure of the time required for small percentages of austenite to decompose, during continuous cooling, to pearlite, bainite, proeutectoid ferrite, or proeutec-toid carbide. In the practical heat-treat- ment of steel, also, the decomposition of austenite is usually not isothermal but rather during cooling, or, in general, is not at a single constant temperature. Thus, both hardenability and practical heat treatment involve anisothermal decomposition of austenite. In a previous publication1 the author and his collaborators outlined the principles that govern the relations between isothermal and anisothermal decomposition of austenite, and reviewed the experimental information available in 1945. To avoid repetition, familiarity with that article (Paper I) will be assumed, and attention given primarily to work carried out or published since 1945. The method generally employed was explained in Paper I: anisothermal transformation is studied through investigation of the effect of holding austenite at one temperature upon its subsequent decomposition at another temperature. Both temperatures are below the stability range of the austenite. This paper is confined to studies in which only a small amount of transformation occurred at the first temperature. This is the only case of importance in practical heat treatment when an essentially martensitic structure is sought. Materials and Procedure It was necessary to use different steels for the studies involving proeutectoid ferrite and for those involving proeutectoid carbide, beeause the two constituents have not been found to form in the same steel. Several steels were tried and rejected

Jan 1, 1949

By Leonard D. Jaffe

In recent years, the advantages of tempered martensite as a microstructure for steel parts have been well established. For parts that must not fracture brittlely when loaded at high rates, at low temperatures, or under conditions of combined stress, tempered martensite is especially desirable. One of the factors that determine whether a steel part will have a martensitic structure after heat treatment is the hardenability of the steel. Despite the large amount of recent research, there are still many unsettled basic questions concerning hardenability and its relation to chemical composition, and, indeed, considerable disagreement among investigators in the field. Much of the uncertainty that beclouds the existing knowledge of hardenability arises from the fact that hardenability is still a wholly empirical concept, and has not been quantitatively related to the more fundamental knowledge of isothermal decomposition of austenite. Hardenability is, essentiaily, a measure of the time required for small percentages of austenite to decompose, during continuous cooling, to pearlite, bainite, proeutectoid ferrite, or proeutec-toid carbide. In the practical heat-treat- ment of steel, also, the decomposition of austenite is usually not isothermal but rather during cooling, or, in general, is not at a single constant temperature. Thus, both hardenability and practical heat treatment involve anisothermal decomposition of austenite. In a previous publication1 the author and his collaborators outlined the principles that govern the relations between isothermal and anisothermal decomposition of austenite, and reviewed the experimental information available in 1945. To avoid repetition, familiarity with that article (Paper I) will be assumed, and attention given primarily to work carried out or published since 1945. The method generally employed was explained in Paper I: anisothermal transformation is studied through investigation of the effect of holding austenite at one temperature upon its subsequent decomposition at another temperature. Both temperatures are below the stability range of the austenite. This paper is confined to studies in which only a small amount of transformation occurred at the first temperature. This is the only case of importance in practical heat treatment when an essentially martensitic structure is sought. Materials and Procedure It was necessary to use different steels for the studies involving proeutectoid ferrite and for those involving proeutectoid carbide, beeause the two constituents have not been found to form in the same steel. Several steels were tried and rejected

Jan 1, 1949

By J. E. Johnson

Charcoal-iron is quantitively so unimportant compared with coke-iron, that its qualitative importance for many industrial purposes is entirely unkriown to many coke-furnace-men, and to the great majority of the inembers of this Institute. To explain this qualitative importance, and explain some of the fact,ors that affect the quality, are the objects of this paper. A brief review of&apos; the commercial conditions governing the charcoal-iron industry is a necessary preliminary to any adequate treatment of the subject. The advent of coke-iron, which transformed the whole iron industry commercially, left intact a limited production of charcoal-iron in the East and South, which has been conducted almays on the basis of high cost and high quality, with correspondingly high selling-price. In the Northwest, particularly in the Lake Superior district, the development has been along totally different lines, for which the close proximity of the great iron-ore deposits and the great forests of that region mere responsible. When the great white-pine forests were removed there were left behind large areas of hardwood and hemlock, to which little attention was paid in the prosperous years of the white-pine industry. But when the latter declined, the demand for lumber, and the presence of lumber-men, probably more skilled than any others in the world, caused the gradual introduction of these woods into commercial use. It was a matter of ancient knowledge that hardwood made an excellent charcoal, and to utilize the cordwood left after the saw-logs were removed, by converting it into charcoal and using it to smelt ore from the adjacent mines, mas an obvious step. In some cases the establishment of the furnace occurred in-

Jan 1, 1913