Search Documents

By A. H. Geisler, J. H. Keeler

Preferred orientations in rolled and annealed titanium sheets were determined by the Geiger counter spectrometer X-ray diffraction technique. Five annealing textures dependent upon the temperature range of annealing were found, and in order of increasing annealing temperature pendent upon the temperature range are: 1—a deformation like texture, 2—a rotated inorder a-recrystallization temperature texture, 3-a retained u-recrysraIlization texture, on annealing at lower temperatures of the ß-region, 4—a transformation texture based on recrystallized a and predicted by the Burgers' relationship, and 5—a ,ß-cube texture. These results are examined in terms of current theories of recrystallization textures. UMEROUS investigators have described the tex- ture obtained by cold rolling the hexagonal metals, titanium, zirconium, and beryllium, which have c/a ratios less than that of ideal packing, 1.633. The basal planes are rotated out of the rolling plane, about the rolling direction, so that the basal poles are tilted toward the transverse direction as shown schematically in Fig. la. In all instances but one,' it was also reported that the [1010] direction was parallel to the rolling direction (see Fig. lb). Hot rolling has been reported as causing a similar tilt of the basal poles in the transverse direction (see Fig. la) and causing the [1010] direction also to be parallel to the rolling direction as shown schematically in Fig. lb. Annealing after deformation does not appreciably change the tilt of the basal poles in the transverse direction." Beryllium2-7 continues to have the [1010] direction in the rolling direction after annealing, and similar observations for titanium and zirconium' . have been reported for annealing at fairly low temperatures, again as in Fig. lb. At higher annealing temperatures, however, the recrystallized grains of titanium" and zirconium have an orientation such that the [1120] direction is approximately in the rolling direction, although the basal poles are still inclined in the transverse direction. Figs. la and lc show the resulting orientations schematically. This change in orientation has been described as a nominally ±30° rotation of the hexagonal crystallites about the basal poles of the cold rolled texture and is apparent from the results which are summarized in Table I for investigations with the X-ray diffraction technique employing film. The angles y, , and ß are indicated in Fig. 2 which represents the stereographic projection of (1070) poles for the mean orientation of a pole figure. Texture determinations for titanium using the Geiger counter spectrometer have provided similar results except that in some instances additional components of the texture were proposed, as shown by the summary of data in the upper half of Table 11. On the other hand, the spectrometer technique, when applied to zirconium,* has revealed a splitting Recently completed studies of the textures of annealed zirconium", show zirconium to possess textures very similar to those reported here for titanium. Therefore, much of this discussion will include zirconium by virtue of its close similarity to titanium in pref erred orientations. of the intense areas of the pole figure for samples annealed at 600°C. This splitting could be described by a 7" rotation of the tilt axis about the normal to the rolling plane. Such a splitting for the annealed texture relative to the cold rolled texture was not observed in other determinations for either zirconium or titanium using the less sensitive film X-ray methoe and makes the relationship between the two types of texture more complex than the simple rotation about the (0001) pole based on film work. The more precise investigations on zirconium permit the descriptions in the lower part of Table 11, which show that the texture depends quantitatively on the temperature of annealing. When zirconium is annealed at temperatures up to 400°C, the texture is similar to the cold rolled texture, while annealing in the range 500" to 900°C produces a texture which is only approximately described as [11%] in the rolling direction. More precisely described results for zirconium show that the two types of splitting ( 1—about an axis in the rolling plane through an angle given in the second column in Table II and 2—about the normal to the rolling plane through an angle given in the third column of Table 11) depend on annealing temperature. The [1120 is the rolling direction only when the annealing temperature is in the vicinity of 900°C

Jan 1, 1957

By W. F. Chiao

With the application of dislocation damping theory an attempt was made to determine whether the generation and extension of dislocations is inherently more difficult in a brittle steel than in a ductile steel. A ductile steel was compared with a brittle stee1 by simultaneously measuring the ultrasonic attenuation and velocity during tensile test, and the density of free dislocations and their mean loop length were then calculated as a function of strain. The results showed that in the ductile steel there was always a large generation of dislocations and great extension of loop length occurring at some stage within the early plastic region. In contrast, the brittle steel showed very little or no such sudden changes in dislocation dynamic states after the onset of plastic deformation. Furthermore, a strong temperature dependence of dislocation dynamic states was also observed in the ductile steel and a hypothesis was suggested that a thermally activated process of dislocation rearrangement could occur at higher deformation temperatures. The activation energy of dislocation rearrangement at room temperature was estimated as about 2030 cal per mole.C. DUCTILITY is an indispensible property in the application of engineering materials, especially steel. During the past two decades the theoretical and experimental approach to the understanding of flow and fracture of metals has been constantly undergoing changes and progress." while the fracture behavior of metals can be influenced by many factors such as chemical Composition,3 second-phase particle mor-phology,4 and dislocation arrangement,5 it is now a general belief that the fundamental understanding of the ductile-brittle fracture phenomena of solid materials must stem from the study of dislocation dv-namics developed under stress conditions.6,7 Most of the traditional ductility tests, such as Charpy impact test, slow bend test, and tensile fracture test, cannot by themselves reveal directly the mechanisms of ductile to brittle transition of materials. In the experimental investigation of tensile ductility it would be ideal to be able to study directly the dynamics of dis-locations in a bulk specimen during the process of deformation. Since the ultrasonic pulse technique is the only satisfactory method for studying dislocations and the fine details of deformation characteristics in metals in the course of a tensile test, it would appear that a comparative study of ultrasonic attenuation changes during tensile tests of metallic materials exhibiting different ductility might be very informative. So far no work comparable to this study has appeared in the literature. Recent progress in both theory and experiment has indicated the feasibility of studying the dislocation mechanisms of ductility behaviors by ultrasonic measurements during tensile test. Granato and Lucke8 have developed a quantitative theory that enables the calculation of dislocation density and their average loop length from the measurements of ultrasonic attenuation and velocity, and several investigators, including Chiao and Gordon,9'10 have shown that simultaneous ultrasonic measurements can be successfully made during a tensile test. Furthermore, many investigators11-13 have repeatedly proposed in the past several decades that deformation and fracture are mutually self-exclusive, and that the ability or inability of a material to deform plastically, i.e., to generate dislocations, is a major factor in determining whether the material will be ductile or brittle. Thus, in the present work an attempt was made to determine whether the generation and extension of dislocations is inherently more difficult in a brittle steel than in a ductile steel. This article is principally concerned with the study of the relation between the propagation of ultrasonic waves and tensile deformation in a steel series which displays quite different toughness at room tempera-turk. changes in attenuation and velocity of ultrasonic waves have been measured as a function of strain during the deformation process. The results have been interpreted in terms of the vibrating string model for dislocation damping as developed by Granato and Lucke, and it has been found that some of the more subtle predications of the model are in good agreement with the experiments. This would be especially meaningful because most of the previous experiments in testfying the model were carried out with single crystals of high-purity materials and little work has been done with polycrystalline steel alloys. EXPERIMENTAL PROCEDURES AND RESULTS Specimen Materials. The tensile specimens used throughout this experiment were of two compositions selected from a series of Fe-Mo-0.77 pct Mn-0.22 pct C steels prepared for a ductile-brittle fracture transition study. One steel contains 0.21 pct Mo and the other 1.03 pct Mo. These two compositions were chosen for the present study because they possess quite different toughness properties at room temperature. The 0.21 pct Mo steel is quite ductile while the 1.03 pct Mo steel is rather brittle, as measured by the standard Charpy impact test. The alloys had been prepared by vacuum induction melting and chill casting in steel molds. The ingots were hammer-forged into 1/2-in.-sq bars from which tensile specimen blanks were cut. These blanks were first normalized under argon atmosphere at 1700°F and then reaus-tenitized and isothermally transformed at 1050°F to a bainitic microstructure. The chemical compositions, heat treatments, hardness measurements, and Charpy transition temperatures of the two steels are listed in Table I.

Jan 1, 1970

By N. Mungan

Laboratory imbibition and displacement experiments were performed using crude oil and cores drilled with water and preserved under anaerobic conditions. The purpose of these tests was to determine reservoir rock wettability and to find out if more oil could be recovered by use of NaOH solution than by conventional waterflooding. The preserved cores were found to be oil-wet. Contrary to work in the literature, these cores changed to water-wet upon contact with air. After exposure to air for a week, the cores yielded more oil by waterflooding than when preserved under exclusion of air. At reservoir temperature of 160F, flooding the preserved cores with 0.5N NaOH solution recovered more oil than an ordinary wa-terflood, and additional oil when following a waterflood. When the caustic solution was used from the beginning, all the extra oil was obtained before breakthrough; when the caustic followed a conventional waterflood, the extra oil was produced in the form of an oil bank ahead of the injected caustic. The increase in oil recovery resulted from wettability reversal. Also, use of caustic reduced the volume of injection required to flood out the cores. At room temperature, however, the caustic solution did not reverse the wettability and gave no additional oil recovery. Cores which had become water-wet by air exposure or caustic flooding were restored to their original oil-wet state when saturated with crude oil and allowed to equcilibrate at reservoir temperature for two weeks. Therefore, in the absence of preserved cores, it may be possible to restore weathered cores to their original wettability for use in laboratory floods. INTRODUCTION Waterflooding has been in use since 1865, and is by far the simplest of secondary recovery methods. Unfortunately, most waterfloods are inefficient in recovering oil, often leaving half or more of the original oil in place un-recovered. The low oil recovery generally results from low sweep efficiency and low displacement efficiency. Consequently, to increase oil recovery by waterflooding, sweep and displacement efficiencies should be improved. Sweep efficiency is primarily affected by reservoir heterogeneities and mobility ratio, while displacement efficiency is affected by the capillary forces between fluids and rock surfaces. For petroleum reservoirs, the capillary forces are expressed in terms of interfacial tension and wettability. If oil recovery is to be improved significantly in water- flooding, the capillary forces holding the oil in the raervoir porous matrix must be reduced or eliminated. One way to reduce capillary forces is to inject commercial surfactants ahead of the injection water into the reservoir. Laboratory tests of this method have shown no promise of an economical process yet, and no increase in oil recovery was obtained in the field trials which have been reported. Work is continuing in many companies to find surface-active agents which, in workable concentrations, can yield substantial added oil recovery. Another way to change capillary forces operating in petroleum reservoirs is by changing the pH of the injected water. Wagner et al.' showed that change in the pH sometimes activates the surface-active materials natural to some crudes and brings about gross wettability change. Since pH alteration can be obtained with cheap chemicals, such as hydrochloric acid or sodium hydroxide, the process shows promise of being economical in a field application. Pan American Oil Corp. reported oil recovery by use of caustic solution from a flooded-out reservoir.' Their test, conducted at a small additional cost, yielded results which were so sufficiently favorable and encouraging that the wettability reversal flood was expanded to portions of the field not previously flooded.13 It is important to bear in mind that changes in the pH of the water not only can reverse wettability but also can lower the interfacial tension between water and crude oil. Reisberg and Doscher4 have studied the pH dependency of the interfacial tension of Venture crude using sodium hydroxide solutions of various concentrations. Their data show that the interfacial tension was lowered from 23.0 to 0.02 dynes/cm by increasing the NaOH concentration from 0.005 to 0.5 per cent by weight. Thus, the use of NaOH may lead to additional oil recovery due to both wettability reversal and lowering of interfacial tension. Whether alteration of pH results in wettability reversal from oil-wet to water-wet and increases oil recovery depends on wetting properties of the reservoir rock and the crude. This necessitates delicate laboratory experiments, with suitable core and fluid samples from a field. Although many investigators have studied wettability reversal floods in the laboratory,1,2,5,6 these studies have been carried out with synthetic porous media, refined laboratory fluids and surface-active chemicals to simulate the process. The study presented in this paper is the first time that wettability reversal by pH alteration has been accomolished in laboratory core floods using carefully preserved natural cores, live crude and with experiments performed at reservoir pressure and temperature.

Jan 1, 1967

By M. Baeyertr

Since 1915 many papers and books have covered industrial applications of X-rays from various angles. Two of the more recent are a paper by Fink and Archer, which describes in detail the technique of radiography, and a paper by Clark2, which embraces the whole field of X-ray metallogmphy. This paper, therefore, is confined to work of the X-ray Laboratory of the Western Electric Co., which naturally divides into two categories: radiography and diffraction patterns of various types. Radiography Radiography is the field in which the application of X-rays has had most general appeal among the industries which produce or use metals and alloys. Equipment permitting the examination of heavy sections of metals less permeable than aluminum or other light alloys requires apparatus capable of generating hard X-rays over a considerable period of time. The equipment used in the work presented in this paper is practically identical with that described by Fink and Archer in their paper on radiography in industry and is easily capable of penetrating 1/8 in. of lead. Radiography is used in two major groups of problems: (1) in the development of cquipment and tools and (2) in studies of materials. So far there has been no instance in which the use of radiography for routine inspection is justified. This is partly due to the fact that the manufacture of telephone apparatus involves the production of many identical parts by standardized procedures and equipment that has had development and trial before being put on a regular production basis. It is during this stage of development of equipment and tools that radiography has been used to particular advantage.

Jan 1, 1931

By J. J. Arps

n approach to the study of the electrical properlies of drilling muds, their cakes and their filtrates was made by treating the drilling fluid as a porous medium. Lluring this study it was found that the weight pararneter was omitted from previous investigations on electrical properties. Patnode in 1949 made a similar approach to ,his investigation. His work showed that there was a variation of resistivity relationships with per cent Puid present in a given suspension. This present study ex-tends Patnode's investigation to one in terms of the solids fraction of the drilling fluids. Previous investigations were made on low weight muds where the effect of the rolids fraction was obscured. The following equationr were fitted to data taken from 94 field muds and 47 laboratory muds (see Tables I and 2). The parameter, C, is a complex function of the solidr content, or mud weight, of a drilling fluid. It was also found that for all drilling muds examined. A nomograph is presented combining Eqs. I and 2. INTRODUCTION It is generally recognized that the materials present in drilling muds affect the relationship between mud filtrate and mud resistivities. However, most electric log interpretations proceed with the assumption that the mud resistivity and temperature are the only important parameters needed to obtain a filtrate resistivity or a mud cake resistivity. Lamont1 suggests that only average relationships exist between mud cake, mud filtrate and mud resistivities. He indicates that there is limited accuracy when these intercorrelated factors are used since no other measure-able variable is apparent. A previous paper by Patnode indicates that drilling fluids may be considered to be a system of fluids in solid particles which may be correlated electrically in a manner similar to rock solids. 1 he equation for the resistivity factor. F = (per cent fluid) is satisfied for a given clay type in water, but the value of m varies as different materials are used in the water. The resistivity factor is not constant for a given amount of clay. As is suspected it varies as the solids fraction conducts electrical current. Since both weighting material and clay solids are present in commonly used drilling fluids, it is expected that both materials contribute to the variation of the m factor in Eq. 3. An extension of Patnode's work is presented in this paper to show some of the interrelations which exist between the resistivities of mud cake, mud filtrate and mud. Use of these data enable a more accurate calculation of mud filtrate and mud cake resistivities if only the mud resistivity and weight are measured. EXPERIMENTAL The measurements of mud weight, fluid and solids resistivity, alkalinity, and chloride content of mud samples were made in this research. Mud samples representing drilling fluids from 94 Louisiana and Texas wells (Table 1) and 47 laboratory-constructed systems (Table 2) were used in the experimentation. The measurements of the mud properties were made both in the field and in the laboratory. The tests on the properties of weight, alkalinity and chloride ion were standard tests as described by API specifications. The resistivity measuring devices were constructed in the laboratory for this study. For details on the resistivity equipment see Fig. 1. The fluid cell

By N. L. Svensson

The model developed by Tuylor for the calculation of Polycrystalline yield strength has been applied to the case of an aggregate hawing a preferred orientation. In general this procedure requires the specification of texture by means of weighting factors applied to specific orientations. The problem to which the model has been applied is that of the yield-strength aniso-tropy of cold-rolled aluminum whose rolling texture was described as a combination of (110)[112] and (311) [112] In this case yield-strength anisotropy is defined by the rutio of yield strength measured at an angle 8 to the rolling direction to that measured along the rolling direction. The method of calculation of yield-strength ratio as a function of ? is described and the results show good agreement with experimental values. The orthotropic yield criterion suggested by Hill has been applied to the results and the strain ratio R also calculated as a function of ?. This has been compared with calculations using the method suggested by Elias, Heyer, and Smith which does not exhibit suck good agreement with observation. one deficietlcy of the method presented is that the strain ratios used by are those applying to iso-Irobic materials. The method should therefore be reg-clrded only as a first abbroximation to the prediction of anisotropy. THE problem of calculating the stress-strain characteristics of polycrystalline aggregates from the properties of single crystals has attracted attention for a number of years. The most important contributions to this study have been those due to: Sachs,' Cox and sopwith,2 Taylor,3 Kochendorfer,4 Batdorf and Budiansky,5 Calnan and Clews,6 Bishop and Hill,7,8 Kocks,9 Budiansky, Hashin, and sanders, 10 Kroner,11 Cyzak, Bow, and payne, 12 Budiansky and Wu,13 and Lin.14 While the earlier work has been largely superseded, recent developments tend to support Taylor's solution" within the restriction imposed by his assumptions. The essential features of Taylor's approach were: 1) the material is rigid-plastic; 2) each grain experiences the same strain components as the aggregate as a whole (the problem was that of uniaxial deformation with principal strain components in the ratio 3) all regions of each grain deform uniformly; 4) work hardening occurs equally on all slip systems. While Bishop and Hill7 have generally validated this approach, there has been some criticism offered. Kocks? as pointed out that since multiple slip must occur the single-crystal data must be determined from orientations arranged such that polyslip takes place. Boas and Hargreaves,15 and others, have shown experimentally that the strain distribution within grains is not uniform, the strains in the vicinity of grain boundaries being less than those in the center of the grains. Both of these criticisms can be largely offset by the suitable choice of single-crystal critical shear stress. However, for the problem analyzed below, the critical shear stress is not directly used and, consequently, these criticisms lose their importance. The more recent contributions have attempted to obtain a more complete analysis by considering an elas-toplastic material and considering interactions between grains of differing orientations. Lin14 has considered the early stages of yielding for a polycrystalline aggregate having specific regions of defined slip plane orientations. On the other hand, Budiansky and Wu13 have allowed for these interactions for randomly disposed grain orientations and have calculated the polycrystalline stress-strain curves for crystals exhibiting either elastic-ideally plastic or kinematic hardening characteristics. This work has shown that yielding commences when the macroscopic stress is 2.2 times the critical shear stress for slip in a single crystal (7,). The yield stress-strain curve then rises becoming asymptotic to a value of 3.072 7,. This is close to the value obtained by Bishop and Hill (3.06) in their confirmation of Taylor's method. This, of course, is to be expected since, at large strain values, the elastic strains are negligible and the rigid-plastic model is satisfactory. The results of Budiansky and Wu indicate that the result obtained by Taylor is 7.7 pct high at a plastic strain which is two times the elastic strain at the initiation of yield. By defining the anisotropy in terms of relative values, the ratio of yield strength at orientation ?, to that measured in the rolling direction, the effect of the discrepancy in Taylor's solution is considered to be of lesser consequence. Therefore, it is anticipated that an analysis based on Taylor's solution, which can be quite straightforward, should provide a reasonable estimation of the anisotropy of materials having a preferred orientation texture. OUTLINE OF TAYLOR'S METHOD In fee metals there are four possible slip planes (the octahedral planes) and in each there are three possible slip directions (the edges of the octahedron), that is a total of twelve possible slip systems. von Mises16 has shown that at least five independent slip systems must become operative in each grain of the polycrystalline aggregate in order to preserve continuity of strain. With this geometrical requirement as basis and the assumptions previously listed, Taylor determined the operative slip systems for a number of orientations of the tensile stress axis specified in the unit stereographic triangle. For the ith slip system, the critical shear stress

Jan 1, 1967

By Tom Westgarth

As papers are placed before you upon large gas-engines in Belgium and Germany, it was considered that some information should be given upon the same subject in Great Britain. I therefore agreed to compile these notes, which I have made very short in view of the somewhat full nature of the other papers presented to this meeting, and considering the complete nature of the many publications which have been made recently upon the subject of large gas-engines. I give below Tables I. to VI., showing the number and particulars of large gas-engines which have been built or are building by British makers, and in view of the growing size of gas-engines I have concluded that engines less than 500 h.p. cannot now be included in the category of large gas-engines, and therefore I have not considered engines under that power.

Nov 1, 1906

By S. H. Moll, R. E. Ogilvie

The investigation of solid-state diffusion phenomena may lead to much information concerning binary alloys. In particular, a study of the concentration gradients present in multiphase diffusion couples can lead to the determination of the solubility limits of the single-phase fields in the phase diagram. The specific concentration gradient which results from the heat treatment of a diffusion couple depends not only upon the time and temperature of diffusion, but also upon the number of phases existing in equilibrium at the diffusion temperature. Such concentration gradients possess sharp discontinuities whose terminal points correspond to the solubilities existing at the limits of the two-phase field in the phase diagram at the diffusion temperature. In general, there will be a discontinuity in the concentration curve for each two-phase field which exists in the phase diagram between the concentration limits of the couple. A number of investigators have analyzed the gradients present in multiphase diffusion couples. 1-8 The iron-titanium phase diagram exhibits a y loop in the temperature range from 900" to 1400°C, and the limit of the a + y field lies at some composition which is less than 1 wt pct Ti for any temperature. It was felt that a diffusion study could yield values not only for the diffusion coefficients involved, but also for the chemical solubilities in the phase diagram. The concentration gradients were analyzed by an X-ray absorption technique developed by Ogilvie.6 The absorption of a monochromatic X-ray beam is measured in steps parallel to the diffusion direction and the resulting intensity gradients are transformed into concentration gradients by applying the laws of X-ray absorption in a binary system. This technique has been applied by ogilvie6 to the systems Ni-Au, Cu-Au, Fe-Cr, and Ni-Cr; by Gelles7 to the systems Be-Fe, and Be-Ni and by Hilliarde to the system Al-Zn. Linear X-Ray Absorption Analysis—The use of X-ray absorption analysis as a tool for determining concentration gradients arises from the fact that the beam is absorbed according to the quantity and species of elements present in the sample and not according to their state of aggregation. This method is more advantageous than the chemical analysis of machined layers since it is less time consuming and less expensive and can analyze a very small area. IF a homogeneous binary alloy (A + B) is analyzed with two different monochromatic X-ray beams I0(2) and lo(2) the following relation between the transmitted intensities, the intrinsic absorption coefficients of A and B for the two different radiations and the weight fraction of each element may be derived.' In (I/Io) (a+b) xa(u/p)a(2) + xb(u/p)8(2) Eq. [1] is independent of specimen thickness and density, but requires that either element A or B possess an absorption edge between the wavelength limits of the two monochromatic beams. I, is evaluated for each radiation by measuring the transmitted intensity through a varying number of foils of a suitable absorber. A plot of the natural logarithm of the transmitted intensity as a function of the number of foils, when extrapolated to zero foils, yields the value of I,. If a plot of the ratio in Eq. [ I] is calculated as a function of xA, then a master curve results. From

Jan 1, 1960

By I. Nilsson, G. Sundkvist, A. Danielsson

A spectrochemical method of slag analysis is descibed which utilizes fusion of the sample with a flux, then cooling and crushing to put all samples into a common form. The powder, is then fed onto adhesive tape and passed through a spark by means of a special device to provide very reproducible discharge conditions. Combined with a direct-reading optical emission instrument, this system provides speed and accuracy of antilysis heretofore unobtainable for. slag samples by any other method. THERE are many suggested methods for spectro-chemical analysis of slags. The most important are fusion-pellet methods and solution methods. In our company the fusion-pellet method has been used earlier, and is described by Lounamaa. W. H. Tingle and C. K. Matocha have made refinements of the pellet method.' A Committee of the British Iron and Steel Research Association has investigated different methods of spectrochemical analysis of slags. Its purpose was to formulate a method which would give the complete analysis in 30 min with an accuracy of ±3 pct. The committee recommends a solution technique, which was thought to correspond best to their requirements. The method to be described is a fusion-tape method. The sample is isoformed by fusion and grinding. The powder is analyzed with the tape technique. The tape machine and some of its applications are described earlier.4'5 The powder to be analyzed is continuously fed onto a moving adhesive tape, which passes through the spark gap. The sparks break through the tape and vaporize and excite the material to be analyzed. The most outstanding feature of the tape machine is its very high reproducibility. The concept of isoformation has been introduced earlier.= It means a pretreatment of the samples to make them uniform from the spectralanalytical point of view, i.e., cancelling systematic differences between the samples. The purpose of the isoformation is to reduce the influence of particle size, as well as chemical and mineral composition. Before describing the isoformation by fusion plus grinding, which is the purpose of this paper, a few words will be said about two other types of isoformations, i.e., grinding with buffer and ion exchange plus grinding as they have been considered during the application of the tape technique for slag analysis. Grinding with buffer might be a sufficient isoformation in some special cases, where the mineral composition is defined. The time of grinding must, however, be rather long, at least 5 to 10 min, even when using such an efficient mill as the Swing Mill from Messrs. Siebtechnik, Mühlheim, Germany. This type of isoformation is not recommended due to its limitations and due to the fact that the gain in time compared with the fusion technique is almost negligible. The principle of ion exchange plus grinding and some of its applications have been described.5 The following elements of interest in slag analysis can be determined in this way: Na, K, Cu, Mg, Ca, Ba, Zn, Pb, Al, Cr, Mn, Fe, Co, Ni. The very important element Si, however, cannot be analyzed with this method. Although the ion exchange isoformation for slag analysis cannot be looked upon as a routine method, it can be used for

Jan 1, 1962

By J. J. Taber

The turbulent flow drag coefficients, or friction factors, have been experimentally determined for the cut-tings normally encountered in drilling operations. The gas law and average drag coefficients for characteristically flat particles (limestones and Shales) and for angular to sub-rounded particles (sandstones) were used to extend Newton's equation to a more useful form. The resulting equations are expressions for the slip velocity of a particle as a function of the particle size and shape, the bottom-hole injection Pressure, and the Bottom-hole temperature. The velocities necessary to lift actual rock cuttings as observed in the laboratory were compared with velocities predicted from the derived equations. Results indicate that there is no single correct circulating velocity and that the commonly used 3,000 ft/min linear velocity may he sufficient to lift only very mall particles. The advantage, in terms of horsepower requirements, of cycling high pressure air to obtain lower compression ratios was shown. INTRODUCTION A promising departure from standard rotary hydraulic drilling is air or gas drilling. In many instances the rate of penetration and bit life increases resulting from this method have been very substantial. Further the application of air drilling in areas of lost circulation or water sensitive pay zones has been highly successful. Purpose For the drilling contractor, the practical question remains, "How much air pressure and volume should I have?' lt is necessary to have a reasonable knowledge of the air velocities and pressures required in air drilling operations for the proper design and most advantageous use of surface equipment and for adequate removal of cuttings from the borehole. Eased on experience, most operators agree that at least 3,000 ft/min linear velocity is necessary for satisfactory hole cleaning.' It was the purpose of this investigation to evaluate the drag coefficients, or friction factors, for the cuttings normally encountered in drilling operations, i.e., sandstones, limestones and shales, and to utilize the values obtained to develop an expression for the minimum velocities and pressures (hence the volumes) necessary to lift these cuttings. THEORY Several investigators have done extensive work on the ability of drilling mud to lift bit cuttings. They conclude that the ability of a drilling mud to lift cuttings is dependent on the density difference between the rock being drilled and the drilling mud, the cutting size and shape, the mud flow constants, and the flow state (laminar, transitional or turbulent) of the mud. However, drilling muds are not true fluids but have a variation of viscosity with velocity in laminar flow and a constant apparent viscosity in turbulent flow. A survey of the literature revealed that no experimental work had been done to determine the velocities necessary to lift actual rock cuttings using a compressible fluid such as air or gas. In 1953, Nicolson6 stated that in air drilling fluid mechanics the particles could be assumed spherical in shape and that ; constant drag coefficient of 0.5 could be used due to the highly turbulent flow of the circulating air. By equating the turbulent resistance on the particle to the gravitational force on the particle, he obtained the expression, ^ = 2.67^y ,.......(1) where V, is slip velocity of spherical particle, ft/sec; D is particle diameter, in.; p, is particle density, 1b/ft8; and p, is fluid density, lb/ft3. However, as stated earlier, most operators seem to agree that adequate hole cleaning can be obtained by circulating a sufficient volume of air to give a linear velocity of 3,000 ft/rnin in the annular space. Basic Equation The velocity with which a solid particle freely falls through a fluid will increase until the accelerating force, gravity, is equal to the resisting forces, buoyancy due to the fluid displaced by the particle and friction due to the relative motion of the particle through the fluid. When the accelerating and resisting forces become equal,

By A. R. Rosenfield, G. T. Hahn

The effects of adding 0.025 volume fraction of uniformly dispersed Tho2, particles (particle size -380A) to iron have been examined. The two-phase alloy is shown to have a lower transition temperature and higher cleavage stress than either the base metal or a solid-solution alloy (Fe-3Si). Enhanced cleavage resistance is thought to be a consequence of particles limiting the effective slip distance of dislocations and thus the ability of Pile-ups to act as stress concentrations. Further calculations predict that the highest cleavage strengths are attained with uniform dispersions, where the particle size is kept small (-250A) and the volume fraction is relatively large (-2 to 3 pct). ALTHOUGH a fine dispersion of second-phase particles is known to impart strength to an alloy, the possibility that it might also impart ductility has only recently been explored. Outstanding progress has been made in the production of ductile tungsten alloys containing Tho21,2or (Hf, Zr)C,= but the contribution of the dispersion to ductility has neither been optimized nor fully analyzed. The basis for such an analysis has now been developed1,5 and is discussed briefly below. Experiments on iron are also described that attempt to isolate one of the possible ductilizing mechanisms and test its effectiveness. In analyzing these experiments, it is important to remember that cleavage obeys a stress criterion, and that either a lower ductile-to-brittle transition temperature or a higher cleavage stress is evidence of enhanced resistance to cleavage. DUCTILIZING MECHANISMS Slip Blockage. Cleavage fracture of polycrystals may be initiated at the intersection of a slip band (or twin) and a neighboring grain or a large (-1 to 5 µ) particle. The slip band generates a stress concentration at its head, and either the grain boundary fractures, the particle fractures, or cleavage is initiated in a neighboring grain. Experimental evidence for this viewpoint is found in metallographic studies8-8 and from the observation that cleavage is usually preceded by yielding.8-11 The potency of a slip band as a stress concentrator

Jan 1, 1968

By P. K. Koh, H. A. Lewis, H. F. Graff

New data on the distribution of silicon between slag and carbon-saturated iron at 1600Oand 1700OC are presented which, in combination with previously published data, permit the determination of silica activities over a broad range of compositions in the CaO-Al2O3-SiO2 system. The distribution of silicon between graphite-saturated Fe-Si-C alloys and blast furnace-type slags in equilibrium with CO has been described in previous publications.1"3 In this past work the silica-silicon relation was established at temperatures of 1425" to 1'700°C for slags containing up to 20 pct A12O3. This paper presents the results of additional studies at 1600" and 1700° C which extend the silicon distribution data at these temperatures for CaO-A12O3-SiO, slags over a range from zero pct Al2O3 to saturation with Al2O3, or CaO.2Al2O3. The upper limit of SiO2 is set by the occurrence of Sic as a stable phase when the metal contains 23.0 or 23.7 pct Si at 1600" or 1700°C, respectively. The activity of silica over the expanded range is determined directly from the distribution data.3 Recently4-7 other investigators have studied the activities of SiO, and CaO, principally in the binary system, using different methods and obtaining somewhat different results. EXPERIMENTAL STUDY The experimental apparatus and procedure have been fully described in previous publications.1, 3 Six new series of experimental heats have been made, four at 1600° and two at 1700°C. Master slags of several fixed CaO/Al203 ratios were pre-melted in graphite crucibles, and these were used with additions of silica to prepare the initial slag for each experiment. Slag and metal were stirred at 100 rpm and CO was passed through the furnace at 150 cc per min. The initial sample was taken 1 hr after addition of slag at 1600°C or 1/2 hr after addition at 1700°C. The run was normally continued for 8 hr at 1600°C or 7 hr at 1700°C, and the final sample was taken at the end of this period. Changes in Si and SiO2 content indicate the direction of approach to equilibrium, and in a series of runs where the approach is from both sides this permits approximate location of the equilibrium line. Fig. 1 shows the results of such a series of 15 runs at 1600°C for slags of CaO/Al,O3 = 1.50 by weight. Figs. 2 and 3 record other series at 1600°C and Fig. 5 a series at 1700°C with fixed CaO/Al0 ratios. The results of the experiments at 162003°C have been reported in part in a preliminary note.3 In the experiments recorded in Figs. 4 and 6, the slags were saturated with A12O3 (or with CaO.2A12O3 within its field of stability) by suspending a pure alumina tube in the melt during the course of the run. The final slag analyses were used to establish the liquidus boundaries8 in the stability fields of CaO.2Al2O3 and of Al20,. ACTIVITY OF SILICA The free-energy change in the reaction has been calculated by Fulton and chipman2 from recent and trustworthy data including heats of formation, entropies, and heat capacities. The more recent determination by Olette of the high-temperature enthalpy of liquid silicon is in satisfactory agreement with the values used and therefore requires no revision of the result which is expressed in the equation: SiO2 (crist) + 2C (graph) = Si + 2CO(g.) [1] &F° = + 161,500 - 87.4T The standard state for silica is taken as pure cristobalite and that of Si as the pure liquid metal. Since the melts were made under 1 atm of CO and were graphite-saturated, the equilibrium constant for Eq. [I] reduces to K1 = asi /asio2. The value of this constant is 1.77 at 1600°C and 16.2 at 1700°C. Through K1, the activity of silica in the slag is directly related to the activity of silicon in the equilibrium metal.

Jan 1, 1960

By Daniel T. O’Brian

Mineral exploration activities are benefiting from new interpretive techniques which have become economically practical with computers. Government agencies, educational institutions, and industry have each contributed research and development efforts for improving the mathematical analysis and graphical display of exploration data, resulting in operational aids not foreseeable a decade ago. Progress has been worldwide and is expanding rapidly. Books 1-10 are supplementing the periodic literature, at least one abstracting service is now active, 11 and an association has recently been formed to encourage and publicize advances in this field. 12 With the diversity of applications, only partial coverage of the subject can be made at any single symposium. Four of the six papers in this section report on the current state-of-the-art in selected areas of interest: graphics, time-sharing, mathematics, and economic analysis. The remaining two papers are descriptions of advanced statistical techniques for gaining additional information during exploration, and illustrate methods which will become more commonly applied in the future. "Computer Graphics: A New Tool for Exploration and Mining" describes the use of a computer and accessory equipment as an information retrieval device, graphically merging and displaying pertinent information for visual inspection and interpretation. This is a rapid means of studying information which has been pre-stored in a form accessible to the computer. Time-sharing is a means of achieving a comparable rapid response when calculations are being performed. The paper, "Some Applications of Time-Sharing in Mining Geophysics," describes the experience of one company using a time-sharing facility for geophysical computations. Another paper on this subject, stressing mining applications, has recently been published. 13

Jan 1, 1969

By H. H. Waller, D. L. Monroe, D. P. R. Smyth

ORIGINALLY slusher drift development was conventional, advancing the drift full 10x13-ft size at 6 ft per round. This proved dangerous and costly because the weak fractured rock of the orebody cannot be left raw for any length of time without its reacting with air to cause spalling. With this method of drift development ground conditions were worsened by many blasts and the length of time it was necessary for the drift to remain open. The problem was practically solved by driving 5x7-ft pilot drifts, then enlarging to 10x13-ft raw size by slashing with 50 to 60-ft diamond drill holes. Calculated explosive charges are used to avoid wall and roof shattering. Still more recently jacklegs and sectional steel replaced the diamond drills, resulting in the same work for less than half the cost, see Figs. 1 and 2. Crosscuts at right angles to the main haulage drifts, which cross through the center of the ore-body, divide the ore into 200-ft blocks. Eight slusher drifts on 50-ft centers draw from one block. The slusher floor is 11 ft above the rail, inclined at 1 pct grade, and the top is 18 ft below the undercut. The finished slusher drift is 102.5 or 120 ft long, depending on whether it is north or south of the crosscut. Drawpoints are staggered on each side at 17.5-ft centers. The completed drift is concreted and has an inclined ramp and a vent at the back. When crosscuts and gangways have been excavated and concreted and slusher stations installed, slusher drift development is carried out in 10 clear-cut stages: 1—Pilot drift is driven full length, 5x7 ft. 2—Station is excavated at half-way point in pilot drift. 3—Pilot drift is enlarged to slusher drift size by drilling. 4—Lower part of slash is blasted and mucked for floor concrete. 5—Floor is poured. 6—Inside upper half of slusher drift is blasted, mucked, and concreted. 7—Outside upper half of slusher drift is blasted, mucked, and concreted. 8—Drawpoints are excavated. 9—Drawpoints are concreted. 10—Concrete ramp and sheave protection recess are constructed at back end of slusher drift. A 5x7-ft pilot drift is driven full length on the center line of the proposed slusher drift using a jackleg and detachable bits on 7/8-in. hexagon steel. A 10-hp air-driven slusher and 36-in. scraper pull muck directly into cars in the main haulage crosscut, see Fig. 2. Operations are on a three-shift basis. One man mucks the previous round, drills, and blasts his round in a shift. Average advance is 5 ft per shift. When the pilot drift is completed, 7 ft of drift in the center section is enlarged to full raw slusher drift size of 10x13 ft, for the set-up to drill long slash holes. The pilot drift is slashed to full raw size from this station with jacklegs and tungsten carbide chisel bits on 7/8-in. sectional steel. Crews line the holes without trouble, working from controls established by the engineers, and the pattern of holes for the slash is arranged to give the least shattering effect

Jan 1, 1955

By D. A. Elgillani, M. C. Fuerstenau

In this paper, oxidation potentials measured in the presence of various concentrations of cyanide, ferro-cyanide, and ferricyanide and ethyl xanthate at various values of pH are related to flotation response. Eh-pH diagrams are presented to show that the formation of surface ferric ferrocyanide is probably responsible for depression when cyanide is added. The influence of cyanide on the depression of pyrite with xanthates as collector has been the subject of a number of investigations,'-6 and several theories on the mechanism of depression have evolved from these studies. Wark and Cox7 and Gaudin8 have suggested that the depressing effect is due to a competition of cyanide ion with xanthate ion for the surface. Cook and his colleagues9-11 have explained this phenomenon in terms of competition between hydrocyanic acid and xanthic acid. Sutherland 12 has shown that although both of these theories accurately describe the relation between pH value and cyanide addition at constant collector addition, they fail to describe the relation between pH value and the amount of collector required to cause flotation. Taggart 13 suggested that depression in these systems is due to the formation of a reaction product between ferric ion at the pyrite surface and ferrocyanide ion derived from solution. Majumdar4,6 has attempted to prove this hypothesis by measuring the contact angles of pyrite in the presence of 25 mg per liter ethyl xanthate and different concentrations of potassium ferrocyanide and ferricyanide. In all cases the contact angles were quite high up to pH 10. These results indicate that pyrite should not be depressed by either potassium ferrocyanide or ferricyanide. In view of these facts, Majumdar has assumed that the compound Fe(CN)2 forms at the surface. Gründer and Bornl4 have stated that depression may be due to the formation of the compound K2Fe(II)Fe(CN)6 at the pyrite-solution interface. This compound is thought to be an interaction product between the K2Fe(CN)6-2 ion from solution and the Fe++ ion at the pyrite surface and, accordingly, K4Fe(CN)6 should depress pyrite at least as effectively as KCN. This was proven experimentally, but there was no simple relation between the depression of pyrite and the concentration of either KCN or K4Fe(CN)6 in solution. In view of the many mechanisms that have been proposed for pyrite depression by cyanide, it is apparent that a clear understanding of the phenomena occurring in these systems is lacking. One reason for this may be the fact that the species responsible for pyrite flotation in the presence of xanthate is not the xan-thate ion but rather dixanthogen.15 Since the oxidation of xanthate to dixanthogen is dependent on the oxidation potential of the solution, it would seem that knowledge of these potentials would be a requisite to understanding the pyrite-xanthate-cyanide system. It is the object of this paper to measure both the oxidation potential and pH of the pyrite systems in the presence of various concentrations of cyanide, ferrocyanide, and ferricyanide and xanthate and to relate these values to flotation response. EXPERIMENTAL MATERIALS AND 'TECHNIQUES In the experiments discussed here, pure potassium ethyl xanthate was used as collector, and reagent grade potassium cyanide, potassium ferrocyanide, and potassium ferricyanide were used as depressants. Reagent grade HC1 and KOH were added for pH adjustment. Conductivity water, made by passing distilled water through an ion exchange column, was used in all experimental work. Two natural samples of pyrite were used in the investigation. Sample preparation for flotation included dry grinding with a mortar and pestle and sizing the product to 100 x 200 mesh. Prior to flotation, a 0.75-gm sample of pyrite was added to a solution containing a known amount of depressant at the desired pH value, and the system was conditioned for 4 min. Following this, a known amount of collector was added and the system was conditioned for another 4 min. The pH — termed flotation pH - was measured; the pulp was transferred to a Hallimond cell, and flo-

Jan 1, 1969

By K. T. Koone, R. J. Blackwell

One of the more important problems to be solved in designing a miscible flood is related to the size of the solvent bank used. Size of the bank may be critical to economic success. Too large a bank loses money; too small a bank may deteriorate and fail to maintain the miscibility needed for high recovery. An important factor in deterioration of a small bank is permeability channeling. In a highly stratified reservoir, solvent speeds ahead in the more permeable zones and mixes laterally with fluids bypassed in adjacent, low-permeability strata. Numerical solutions have been obtained .for the differential equations that describe the movement of a slug through a two-layer system in which mixing occurs both in the direction of flow and transversely. The solvent slug is assumed to have the same density and viscosity as the resident fluid and the pushing fluid. These solutions have been verified by comparing them with similar concentration profiles obtained in the laboratory in a 36-ft stratified model packed with glass beads. The theoretical study revealed that when the dominant mechanism causing a bank to fail is lateral mixing the bank size needed for a given recovery may increase with length rather than decreasing as the square root of reservoir length, as suggested by one-dimensional mixing theory. From a comprehensive examination of the variables, a generalized correlation is developed that relates strata thicknesses, bank size, fluid velocity, mixing coefficients, system length and simple solvent-resident fluid phase behavior to the area miscibly swept. INTRODUCTION Miscible displacement, or solvent flooding, continues to receive widespread attention as a method for increasing oil recovery over that possible in conventional gas-drive or waterdrive projects. A basic economic requirement in the application of such processes is the use of as little solvent as possible. A basic physical requirement is that enough solvent be used to maintain miscibility. Economics places an upper limit on the size of a solvent slug, and physical considerations establish a lower limit. Consequently, the practicality of any given miscible process requires that the economic limit be greater than the lower limit imposed by physical requirements. Procedures exist for determining the economic limit; however, procedures for determining realistic minimum bank sizes exist for only special reservoir situations. In the past, bank size has usually been selected on the assumption of a piston-like displacement for which only longitudinal mixing is important. This assumption leads to the favorable conclusion that bank size, expressed as per cent of pore volume, is inversely proportional to the square root of length. Collins considered the problem of transverse mixing of solvent with fluids in bypassed zones with the assumptions that no forward mixing occurs and that the concentration is uniform in the permeable stratum of interest. 1 Lauwerier considered a mathematically similar problem in thermal recovery operations.2 Their work suggests the much less favorable conclusion that bank size could be directly proportional to the length or even higher powers of the length. This paper considers the physical behavior of a small solvent bank as it moves through a real reservoir, without imposing many of the restrictive assumptions of past treatments. To facilitate mathematical description, an idealized, two-layer model that permits mixing both laterally and in the direction of flow will be considered. A calculation procedure for solving the descriptive equations will be developed for a displacement involving fluids of equal density and viscosity. In addition, laboratory experiments designed to check the computational results will be described, and the coincidence of calculated and observed results will be discussed. The use of many solutions for a variety of bank sizes, strata thicknesses and characteristic system lengths to develop a usable correlation between

Jan 1, 1966

By J. T. Mackenzie

Henry Marion Howe, in whose memory we are gathered together, was one of the great thinkers who develop from time to time to whom is given the rare gift of synthesis. Analysis is given to few, but synthesis, the ability to show the relation of all parts to each other and thus to give a clear picture of the whole, is reserved for the very few. Analysis can be achieved by honesty, intelligence, and industry, but synthesis is only given to genius. Professor Howe's crowning achievement is the picture of the whole iron-carbon series shown in Fig. I, which places steel, malleable, gray iron, mottled and chilled irons in their proper relation to each other and shows the essential unity of the series. Perhaps his best statement of the case is found on page go of the Metallography of Steel and Cast Iron in these words: " Each member of the gray cast-iron series consists of the metallic matrix approximately equivalent to that member of the steel-white-cast-iron series to which it corresponds in percentage of combined carbon with its continuity broken up—by masses of graphite ..." Apparently he had taken considerable interest in this idea around the turn of the century, for he refers to a discussion at the Franklin Institute in I900 in which he said: "Though many others had probably conceived this relation between the steels and cast irons, it was here enunciated for the first time, so far as I know. It was received with great incredulity." The concept was explained in some detail in a paper on "The Constitution of Cast Iron" presented before the A.S.T.M. in 1902 when Professor Howe was retiring president of that young society. In the discussion Dr. Sauveur stated that he was "very well acquainted with Professor Howe's theory of the constitution of cast iron," and went on to say that while he "shared it to the fullest extent, some foundrymen . . . claim cast iron is a metal entirely different from steel . . . that steel and cast iron have very little in common, and that therefore the knowledge gained in the study of steel is of little or no value in the study of cast iron." Dr. Moldenke, in discussing the same paper, said he had been working on the same theory for 12 years but he laid no claim to publication. Discussing the difference in the micro-structure of the metallic matrix, Professor Howe pointed out that "such minor structural differences are indeed to be expected, because of the difference in the conditions under which these constituents are generated. "One difference in these conditions is that the steel of most micrographs has been either forged or at least treated thermally in such a way as to give a new structure radically different from that which formed during the initial solidification, whereas the cast irons have not. Hence what we see in the steels is a transformation structure, but in the cast irons a solidification structure. By giving the cast

Jan 1, 1944

By J. T. Mackenzie

Henry Marion Howe, in whose memory we are gathered together, was one of the great thinkers who develop from time to time to whom is given the rare gift of synthesis. Analysis is given to few, but synthesis, the ability to show the relation of all parts to each other and thus to give a clear picture of the whole, is reserved for the very few. Analysis can be achieved by honesty, intelligence, and industry, but synthesis is only given to genius. Professor Howe's crowning achievement is the picture of the whole iron-carbon series shown in Fig. I, which places steel, malleable, gray iron, mottled and chilled irons in their proper relation to each other and shows the essential unity of the series. Perhaps his best statement of the case is found on page go of the Metallography of Steel and Cast Iron in these words: " Each member of the gray cast-iron series consists of the metallic matrix approximately equivalent to that member of the steel-white-cast-iron series to which it corresponds in percentage of combined carbon with its continuity broken up—by masses of graphite ..." Apparently he had taken considerable interest in this idea around the turn of the century, for he refers to a discussion at the Franklin Institute in I900 in which he said: "Though many others had probably conceived this relation between the steels and cast irons, it was here enunciated for the first time, so far as I know. It was received with great incredulity." The concept was explained in some detail in a paper on "The Constitution of Cast Iron" presented before the A.S.T.M. in 1902 when Professor Howe was retiring president of that young society. In the discussion Dr. Sauveur stated that he was "very well acquainted with Professor Howe's theory of the constitution of cast iron," and went on to say that while he "shared it to the fullest extent, some foundrymen . . . claim cast iron is a metal entirely different from steel . . . that steel and cast iron have very little in common, and that therefore the knowledge gained in the study of steel is of little or no value in the study of cast iron." Dr. Moldenke, in discussing the same paper, said he had been working on the same theory for 12 years but he laid no claim to publication. Discussing the difference in the micro-structure of the metallic matrix, Professor Howe pointed out that "such minor structural differences are indeed to be expected, because of the difference in the conditions under which these constituents are generated. "One difference in these conditions is that the steel of most micrographs has been either forged or at least treated thermally in such a way as to give a new structure radically different from that which formed during the initial solidification, whereas the cast irons have not. Hence what we see in the steels is a transformation structure, but in the cast irons a solidification structure. By giving the cast

Jan 1, 1944

By L. A. Rapoport, W. J. Leas, C. W. Carpenter

A program of scaled flow model experiments has been undertaken to study the performance of five-spot water floods. The modeling procedures are discussed and the construction and operation of the flow models are described. The tests were specifically designed to investigate the effects of injection rate and of oil-to-water viscosity ratio on oil recovery. The areal sweep of five-spot water floods was also studied, and direct comparisons between five-spot and linear flooding behavior have been established to permir better utilizatfon of core analysis results for purposes of field waterflood evaluations. INTRODUCTION For a long time reservoir engineering procedures have been confined to the consideration of idealized, one-dimensional or linear systems.11* However, direct application of the linear waterflood mechanism to the evaluation of actual field performance is justifiable only for the purposes of rough approximation. To obtain a realistic analysis of field behavior, it is necessary to account for reservoir geometry and well distribution, and to take into consideration the configuration of the flow of fluids between injection and producing wells. In the past it has been attempted to account for the complex nature of the fluid movement in the reservoir by associating each well pattern with a certain "sweep-efficiency constant", e.g., a sweep efficiency of 72 per cent for the conventional five-spot pattern.' More recently, methods of waterflood evaluation have been improved by the introduction of variable sweep-efficiency factors, defining the areal coverage as a function of cumulative water injection and viscosity or "mobility" ' ratio.""' These variable sweep-efficiency factors, derived from miscible fluid displacement experiments, require the assumption of piston-like displacement of oil by water. This implies that only one fluid, either oil or water, is moving at any one point of the reservoir ht any moment. Such an assumption, however, is incompatible with the bulk of the experimental evidence and also theoretical considerations which indicate that usually in the area invaded by water, both oil and water are flowing in varying proportions, in accordance with the relative permeability characteristics of the porous medium. Another recent approach toward the evaluation of five-spot flooding behavior involves correlations of the areal sweep efficiency (observed in immiscible fluid experiments) with a "mobility ratio," based on the consideration of the "average" relative permeability to the displacing fluid. Combination of these correlations with a modification of the Buckley-Leverett frontal-drive equation leads to a computational procedure for predicting the recovery performance of areal water floods. While of considerable interest, this approach has no complete theoretical justification and, therefore, does not entirely clarify the features of five-spot water floods. Rigorous, theoretical treatment of waterflood behavior in two- or three-dimensional systems as encountered in the reservoir, including proper consideration of relative permeability and capillary-pressure functions, is as yet beyond the scope of analytical or computational methods. The, behavior of such water floods can, however, be studied by means of scaled flow model ekperiments, which is the approach followed in these investigations. The flow model experiments described in this paper simulate a uniform, horizontal formation of constant thickness with fully penetrating wells. The system under consideration is entirely liquid saturated and not influenced by compressibility effects, which is representative of the situation achieved after gas fill-up under practical conditions. Gravity segregation effects are assumed to be negligible, which implies a relatively thin reservoir formation and/or low vertical permeability. THEORETICAL CONSIDERATIONS For a flow system of uniform thickness with no appreciable effects of gravity segregation, the analysis of water-oil displacement can be confined to a two-dimensional treatment based on the consideration of a "slice" of unit thickness. Referring to previously established derivations," the displacement of oil by water in such a system can be described by the following, dimen-sionless equations:

By M. R. J. Wyllie

Eight laboratory-prepared aqueous base drilling muds representing common mud types, and 15 aqueous base drilling muds sampled in the field, have been used in an experimental investigation of the relationship between the streaming potential developed across a mud filter cake and the differential pressure causing filtrate flow. It has been established that the relationship is of the form, ES = kPy, where Es is the streaming potential, P the differential pressure and k and y are constants for any particular mud system at constant temperature. Beyond a certain minimum thickness this relationship is independent of filter cake thickness. Experiment has shown that both k and y are temperature dependent parameters and that in certain mud systems there is a critical value of P above which the simple relationship Es = kPY ceases to hold. The constant k tends to be a function of the mud resistivity at 77ºF, but the exponent y has not been found to be related to any commonly measured mud property. Certain field experiments are described which serve to demonstrate that the total SP (self potential) developed opposite a formation may be quantitatively accounted for as the algebraic sum of an electrochemical potential and an electrokinetic potential. A chart to permit the simple use of mean solution activities in the interpretation of electrochemical SP data is given and its use described. Various field methods for computing the electrokinetic SP component of the total SP are considered and rejected as being unduly complicated and inaccurate. It is shown that the employment of low resistivity drilling muds is essential if optimum accuracy is desired in the use of the S.P. curve for the purpose of computing connate water salinities by the electrochemical SP method. The use of such low resistivity drilling muds is accordingly recommended. INTRODUCTION In a previous paper' a quantitative analysis of the electrochemical compovent of the SP (self potential) curve was made and it was shown that the electrochemical* emf, E, could be expressed as E = ZtRT/F In a,/a,, where t is the transference number of the chloride ion, R is the gas constant, T the absolute temperature of the formation water and mud, a, the mean activity of the connate water (assumed to be sodium chloride) and a, the mean activity of the mud (as sodium chloride). The essential accuracy of this expression was confirmed by an investigation 2 of the SP kicks opposite sands of known water salinity. The logs examined had been routine runs in oil wells in a number of Mid-Continent states. Further confirmation of the original analysis of the electrochemical SP is implicit in the paper by Tixier3 wherein a relationship between the SP and the ratio of connate water and mud resistivities, based only on field data, is given. Allowing for the fact that mud and connate water resistivities were used instead of activities, and that electrokinetic effects were ignored, the constant reported by Tixier is essentially 2tRT/F. The error involved in the universal substitution of resistivities for activities will receive further reference below. Possible reasons for the fact that the electrochemical properties of shales do not appear to be significantly dependent upon either the nature or the quantity of cation exchange materials, such as clays, they contain has been considered at some length by Wyllie and Patnode.4 In the same paper, the probable effects of shale thickness and compaction on electrochemical efficiency, and hence the inherent difficulty of obtaining reliable laboratory-scale data, were also pointed out. However, it is

Jan 1, 1951