Search Documents

By Joseph Kelly

DEPLETION of anthracite resources in Lackawanna County, Pennsylvania, has forced the recovery of coal tracts formerly considered unminable. Chief among these are the large areas of outcrop coal lying on a heavy pitch on the mountain sides, abandoned thirty or forty years ago as too costly and too hazardous to mine. The old companies, in many instances, stopped their chambers 80 or 100 ft. hack from the actual outcrop, and then dropped back another 100 ft. before starting to rob the pillars, thus leaving large areas of coal. Recovery of this coal naturally leads to mining hazards not encountered years ago. The first step is to sink a slope from the surface with the pitch of the vein, and then drive counters across the pitch as close to the robbed area as proper protection for the lower side of the -counter will permit. Next, the old chambers are advanced or new ones driven in the solid, as the conditions require. As these chambers approach the outcrop the real safety work begins-that of preventing the miner from being buried or locked in by an avalanche of mud.

Jan 1, 1936

By L. A. Schrider, J. A. Wasson

A method of predicting waterflood performance has been developed that combines certain facets of several previously published prediction techniques. The manner of combination has required the development and use of some new and some little-known relationships and has eliminated several of the weaker assumptions inherent in the original individual prediction methods. This approach, which was designed for computer solution, has removed the necessity of referring to plotted curves and permits the analytical prediction of water flood performance for a five-spot well pattern in either homogeneous or stratified reservoirs. The Predicted values are expressed in common oilfield units rather than in abstract or dimensionless terms. The calculation procedure has been programmed in FORTRAN IV and the entire program listing is available to potential users.* Introduction Prior to initiation of secondary recovery of oil by waterflooding, the possibilities of economic success or failure must be evaluated with the greatest practical accuracy. Although many prediction techniques are available, most, if not all, have serious limitations. In recent years, the Bureau of Mines has attempted to stimulate interest in the secondary recovery of oil from Appalachian pressure-depleted reservoirs. Waterflooding, because of its widespread acceptance and success, is the principal secondary-recovery method considered. During the life of the project, several performance prediction methods have been studied and applied. Because these methods, individually, have inherent assumptions and limi-tations, portions of some of them have been selected and combined in an effort to eliminate such shortcomings wherever possible. We believe that the resulting technique is as accurate as the necessary available data will permit and that it has several distinct advantages over previously published methods. Development of the Method The fractional flow equation developed by Buckley and Leverett' from Darcy's law is the fundamental mathematical statement describing immiscible fluid-fluid displacement in porous media. A generalized form of this relationship, whose derivation is readily available in the literature, is The formation dip, a, is usually very small in those petroleum reservoirs being considered for pattern waterflooding in the Appalachian area. Therefore. in many cases. a has an almist negligible value. In addition, Ap, the difference between the density of water and the density of oil, is relatively small. For these reasons the gravitational term may often be neglected. Capillary pressure is a function of saturation, which is in turn a function of distance from the upstream boundary of the system or the injection well. In this study it is assumed that the frontal zone of the waterflooding (or zone of capillarity) has negligible length and that only those saturations in the water-swept zone at breakthrough and later are of interest. As the distance in a waterflood pattern is comparatively large and the change in water saturation with distance is usually small, the change in capillary pressure with distance is negligible. The simplified form of the fractional flow equation is appropriate, therefore, in this application. Three variables must be considered in determining that fraction of the total fluid flow that consists of water: the viscosity ratio, saturation, and relative permeability ratio.

Jan 1, 1969

By Malcolm F. Hawkes

AUSTENITE grain size has long been recognized by metallurgists as an important property of steels because of its influence on toughness, hardenability, machinability and creep strength. Much research has been carried out on wrought steels to develop methods for disclosing austenite grain size, and to provide knowledge of the grain-size -characteristics of steels produced and heat-treated in various ways. Much less work in these fields has been done on steel castings; partly because, owing to the variable and complex microstructures of cast steels, it is frequently very difficult to obtain results that are not questionable. The object of this investigation, therefore, was to establish, for a wide variety of carbon and alloy cast steels, suitable methods for disclosing austenite grain size and some knowledge of the grain-size variations to be expected. The steel foundryman is interested in austenite grain size at two different stages in the manufacture of his products; one is just after the steel is cast, and the other is after any reheating operation carried out above the critical temperature range. In both, it must always be kept in mind that the grain size being sought is actually a previous austenite grain size, and that the austenite no longer exists once the steel has cooled to room temperature. The problem of the investigator is always to use evidence obtained from the structure at room temperature to deduce this previous austenite grain size, which was established the last time the steel existed at a temperature above the critical range. Since most steel castings today are at least annealed or normalized, the measurement of austenite grain size established by heat-treatment will be considered first. More than So commercially produced cast steels representing a wide variety of compositions and melting practices were used in the study. For each steel, grain-size determinations were made after each of three widely varying heat-treating schedules; namely, one hour at 1550°F, one hour at 1700°F, and six hours at 1700°F. The list of steels and results obtained on them will be found in the appendix. (See page 21.) A discussion of the knowledge gained on the applicability of various test methods and on grain-size characteristics of cast steels in general follows. MEASUREMENT OF AUSTENITE GRAIN SIZE ESTABLISHED BY HEAT TREATMENT METHODS SUITABLE FOR DETERMINING AUSTENITE GRAIN SIZE AFTER HEAT- TREATMENT AT ORDINARY TEMPERATURES AND TIMES It was desired, as one of the results of this investigation, to be able to recommend to steel foundries a method, or methods, of disclosing grain size best suited to accurate

Jan 1, 1947

By AIME AIME

The following report is published for the information of the members: Meetings. Two meetings for the reading and discussion of papers, etc., have been held during the year 1907-namely, the Ninety-second meeting, held April 16 to 20 in New York, N. Y., and the Ninety-third meeting, held July 23 to 30 in Toronto, Canada. The proceedings of these meetings, including descriptions of the entertainments and excursions connected therewith, have already been published and distributed to the members of the Institute; the New York meeting in Bi-Monthly Bulletin, No. 15, May, 1907, pp. 541 to 559, and the Toronto meeting in Bi-Monthly Bulletin., No. 17, September, 1907, pp. 847 to 875. In addition to these " Proceedings," there were also published in Bi-Monthly Bulletin, No. 15, May, 1907, an illustrated description of the United Engineering Society building (p1 vi. to xxvi.), and a record of the exercises attending its dedication, including the addresses of Andrew Carnegie, Arthur T. Hadley, Samuel Sheldon, Frederick R. Hutton, John Hays Hammond, and T. C. Martin (pp. xxxviii. to lxv.). At the New York meeting, 43 papers and- discussions were presented, and the names of 297 members and guests were registered at the Institute headquarters., this number, however, does not represent all who were present at the sessions and excursions. At the Toronto meeting, 23 papers and discussions were presented. The number of members and guests registered at the Toronto headquarters was 191, which doubtless does not include the names of all who were present at the sessions, or took part in the numerous excursions and visits around Cobalt.

Mar 1, 1908

By W. L. Martin, J. N. Dew, H. B. Steves, M. L. Powers

This paper presents and discusses the results obtained during a pilot test in the Loco field in southern Okla homa. The test was conducted in a 2%-acre pattern that was part of a 20-acre conventional waterflood pilot area. The conventional flood was well past its economic limit when the hot waterflood was initiated to obtain technical information and operating experience. Temperature data from nine observation wells showed that about 75 percent of the pattern was affected by heat, and that heat losses were severe in the pilot pattern. About 60 percent of the injected heat was lost to overburden and underburden zones during hot-water injection. Wellbore heat losses were held at tolerable levels at the shallow depth of the test by providing a low-pressure air annulus between the injection tubing and well casing. Hot water provided water injectivity increases of 200 to 400 percent. The hot water channeled across the lower portion of the oil sand in three directions through zones of relatively high water saturation. There was no conclusive evidence that natural fractures or pressure partings aflected the flow of fluids in the pilot pattern; however response undoubtedly was aflected by localized pressure gradients and by injection-production rate ratios. The results showed that hot waterflooding increased oil recovery in a reservoir containing 600 cp oil. The total tertiary oil production from the pilot pattern area was 3,896 bbl or about 156 bbl/acre-ft swept by heat. The corre.sponding WOR was about 34:I. Description of the Hot Waterflood Process To hot waterflood an oil reservoir, water is injected that has been heated to a temperature substantially higher than the original reservoir temperature, but lower than the vaporization temperature of water at the prevailing pressures. In the reservoir the hot water flows continuously into cooler sand and rapidly loses heat to the sand until it has been cooled to the original reservoir temperature. Thus, a heated zone and a region or "bank" of cooled water begins to accumulate immediately after hot water injection is started. This bank of cooled water continues to grow ahead of the heated zone, which also grows, but at a slower rate. This occurs because heat transfer is almost instantaneous, and the ratio of heat capacities of water to rock is such that two or three unit PV of hot water must be injected to heat a given unit bulk volume of the reservoir. The primary displacement mechanism is the same for both hot and conventional cold waterfloods; i.e., "piston" displacement occurs at the original reservoir temperature. The incremental benefits of hot waterflooding usually occur long after the breakthrough of cold water at producing wells, and the increased oil recovery necessarily is accomplished with high WOR's (water-oil ratios). Heat decreases the viscosity and density of oil and water. These effects result in more rapid and increased recovery of secondary or tertiary oil. If the cost of the required heat is low enough, the ultimate oil recovery of a hot waterflood should be increased substantially over what would be expected at the economic limit of a conventional cold waterflood. The economic benefits of any hot-fluid injection project depend primarily upon the cost of the heat required to produce more oil at an increased rate. This cost depends in part upon the amount of heat lost to surrounding formations. Heat loss depends upon reservoir thickness, water injection rate and temperature, the depth of the formation, well spacing, and the characteristics of the reservoir rock and surrounding formations. In general, percentage heat losses decrease as injection rate and reservoir thickness increase. Although it is an old idea, hot-water injection has not received widespread field application in the oil industry as a drive process. Much of the original field work with hot water was done in Pennsylvania fields where water permeabilities and injection rates are low. In these cases, hot-water injection was used primarily as a means of increasing in-jectivities — not as a recovery process. Ramey' recently has published an excellent review of the development of hot fluid injection processes. Recent publications"' and our own experiences now indicate that hot water or steam injection also can effectively increase the oil recovery from reservoirs containing viscous crudes. However, the economics of these methods as displacement processes have not been established. Several theoretical predictive techniques have been published (for a review see Ramey'), but simplifying assumptions make

Jan 1, 1969

By S. W. Miller

DURING the examination of welds made in steel by the oxy-acetylene and electric-arc processes, the writer has met with some unusual structures, which he has not encountered elsewhere. They seem to be quite closely associated with the welding methods used, and characteristic of them, and would seem to be worth noting, especially as the references to them in the literature are few, and their explanation not clear or complete. An introductory word or two about fusion welding may not he out of place. The oxy-acetylene process is based on the great and very local heat generated by the burning of acetylene in the presence of commercially pure oxygen, the two gases being thoroughly mixed before combustion. The theoretical temperature is somewhat under 4000° C., but on account of various losses, the actual maximum temperature is probably about 3000° C. 1 The electric-arc process, using a metal electrode, which is also the filling rod, generates a still higher and more local temperature. The actual temperature of the positive crater of the carbon arc is given as 3500° C.2 No figures have been found for the temperature of the arc using a metal electrode, but it would probably not be very different from that of the carbon arc, and probably higher than that of the oxy-acetylene flame. The greater localization of the electric arc is due to the fact that it is not surrounded by a large envelope flame as well as to its higher temperature; while the oxy-acetylene white cone, or welding flame, in which the carbon of the acetylene is burned to CO, is surrounded and preceded by -a long envelope flame, itself of quite high temperature, in which the CO is burned to C02, and the hydrogen of the acetylene to

Jan 2, 1918

By A. L. Benham, W. E. Dowden, W. J. Kunzman

The mechanism involved in creating a miscible fluid displacement of typical reservoir fluids through porous media by light hydrocarbon mixtures usually involves a number of mixing and separation stages in the contact area. This mechanism has been illustrated on ternary diagrams for miscible displacement of reservoir fluid by rich hydrocarbon gases. A relatively simple method has been devised for calculating the approximate conditions for a miscible displacement of reservoir fluid by rich, light hydrocarbon gases or by LPG mixtures. Miscibility is favored by increased pressures, decreased temperatures, light reservoir fluids and light hydrocarbon-displacing fluids rich in the heavier components. The conditions for miscible displacements of five typical reservoir fluids by various light hydrocarbon mixtures were determined for a range of temperatures from 70" to 260°F and pressures from 1,000 to 3,000 psia. A correlation of these conditions was obtained using the variables of temperature, pressure, C,+ molecular weight of the reservoir fluid, C,+ molecular weight of the displacing fluid, and mol per cent methane in the displacing fluid. This correlation has been applied to data appearing in the literature with very good success. A partial check of the correlation has been made using a step-wise procedure with a windowed PVT cell. INTRODUCTION The term, "miscible fluid displacement", may be defined as any oil-recovery displacement process where there is an absence of a phase boundary or interface between the displaced and displacing fluids. A water flood would not be a miscible fluid displacement, although cycling in a condensate reservoir would be. Another example is displacement of oil by gasoline. Not so obvious, however, are the conditions under which fluids (such as propane, mixtures of propane and methane, or other similar systems) will give a miscible fluid displacement of oil. There are four standard miscible-fluid-displacement processes being used for the recovery of oil from an "nderground reservoir—(1) high-pressure dry-gas miscible displacement, (2) rich-gas miscible displacement, (3) miscible slug using a slug of LPG followed by a lean dry gas under miscible conditions, and (4) gas driven-slug process using a slug of LPG followed by a lean dry gas under immiscible conditions. The first problem faced by the engineer designing a miscible displacement process is to determine the conditions for miscibility. A number of papers have included discussions of the process of obtaining miscibility in these processes.1-8 However, methods for calculating the conditions for miscibility have not been published. This paper includes a method for calculating the conditions for a miscible displacement of reservoir fluid by a rich gas (LPG diluted with methane or natural gas). In this paper, a rich-gas miscible displacement process is defined as an oil-recovery process in the reservoir. The cost of a rich-gas miscible displacement will be decreased by diluting the LPG with methane or natural gas as much as possible. Therefore, it is important to be able to predict the maximum dilution for miscibility. MECHANISMS The mechanisms for obtaining miscibility between a displacing mixture of light hydrocarbons and displaced reservoir fluid often involve a number of displacing and mixing stages. As stated previously, the cost of a rich-gas miscible displacement is decreased by diluting available LPG with natural gas. The problem is to predict the maximum dilution allowed while maintaining miscibility. To get a picture of the displacing and mixing stages, it is helpful to consider these complex hydrocarbon mixtures as pseu do-ternary systems. Graphical representation of a complex system as a pseu do-ternary system can be thermodynamically rigorous if enough variables are used to describe the character of each pseudo-component in one of the phases. However, even if the characterization of each pseudo-component is not complete, pseudo-ternary representation does serve to illustrate the mechanism for obtaining miscibility and can be used to make some general conclusions concerning the conditions for obtaining miscibility. A phase diagram for the ternary system, methane-

By G. Donald Emigh

Nothing is more important to life-plant and animal-than phosphate. Its compounds are essential to the energy functions of all living systems and for the formation of bones and teeth. Animals get their phosphate from eating plants and other animals, or domestically from feed supplements. Plants get their phosphates from the soil. Man's most important use of phosphate is for fertilizer; approximately 95% of the world's phosphate rock production is consumed by fertilizers. Most of the balance is processed in electric furnaces into elemental phosphorus, the important raw material for making industrial phosphates. Recovery of uranium from phosphates has been possible but not widely used. However, recent significant developments have generated interest in such recovery in the US and elsewhere. Phosphate occurs in all igneous and sedimentary rocks, and in all fresh and salt water. However, economical recovery is limited to deposits where natural concentration of the phosphate mineral has occurred. Occasionally natural concentration is great enough that the material can be used as mined; generally, however, the ore is low grade_ and must be concentrated. Phosphate rock is produced in 31 countries. Fig. 1 shows the location of major phosphate rock producers as well as some of the known phosphate deposits not yet in production. In the last decade the world phosphate industry has experienced steady growth. World production rose from 98 Mt of phosphate rock in 1973 to 140 Mt in 1982. Fig. 2 shows the growth curve of rock production and graphically illustrates the almost straight-line rise since 1945 in both US and world production. Table 1 gives the breakdown, by countries, of world rock production, 1974 through 1979. Table 2 shows US rock production by producing areas. Definitions of Terms Used in the Phosphate Industry Phosphate Rock: Commonly called rock in sedimentary deposits and apatite in igneous deposits. Those expressions generally include any mined, or mined and beneficiated, fluorine-containing calcium phosphate used as the raw material for the next stage of manufacturing. The average phosphate content in rocks is 0.1 to 0.2% P2O5, as documented by McKelvey (1973). About 200 minerals contain more than 1 % P2O5. However, the important mineral in igneous rocks is fluorapatite, [Ca5 (PO4),3 F], containing about 42% P205 and 3.8% F2; in sedimentary rocks the important mineral is francolite, a carbonate fluorapatite containing up to 2% molecular CO2. Both are in the apatite family of minerals. Most phosphate rock, whether beneficiated or not, is a fine-grained material. The expression phosphate rock has no relation to its phosphate content. For example, phosphate rock from Idaho used in the production of phosphorus may contain about 24% P205, whereas rock from Morocco may contain 36.6% P2O5. Phosphorite: A deposit of phosphate directly or indirectly of sedimentary origin, which is of economic interest. Grade of Phosphate Rock: The calcium phosphate content of phosphate rock is expressed in different world areas by one of the following terms: BPL (bone phosphate of lime) TPL (triphosphate of lime) P2O5 (phosphorus pentoxide) P (phosphorus-not commonly used) An illustration of relationship is: 80% BPL = 80% TPL = 36.6% P5O2 = 16% P

Jan 1, 1983

By Anson Hayes, John Chipman

The quality of sheet and strip products made of rimming steel is closely related to the structure and chemistry of the ingots. The variation in composition throughout the ingot, as affected by segregation, is of great importance, as are also the form and distribution of the voids that result from the gases evolved. It is because of this importance that the considerable literature in this field has accumulated. No attempt is made in the present paper to compile a bibliography of the excellent work that has already been done, as this has been adequately covered in the many excellent reports on the heterogeneity of steel ingots prepared by a joint committee and published by the Iron and Steel Institute.' From time to time, in any field of investigation new tools and new technique are developed, which make further progress possible. In the field with which this paper is concerned, this is true. The development of the vacuum-fusion method as a means of following oxygen segregation, and a technique for obtaining the volume and composition of the gases evolved during solidification, have opened the way to obtaining data by means of which some considerable progress has been realized in developing more of the detailed mechanisms of solidification and segregation in rimming-steel ingots. General Theory of Segregation The basic cause of segregation lies in the fact that the impurities are less soluble in solid than in liquid iron. The solid that forms from the impure liquid is more nearly pure than the liquid itself. If solidification proceeds slowly enough, or if the liquid and solid phases are maintained in contact with one another for a sufficient time, a condition of equilibrium is set up, which may be represented by a phase diagram. Portions of the

Jan 1, 1939

By Anson Hayes, John Chipman

The quality of sheet and strip products made of rimming steel is closely related to the structure and chemistry of the ingots. The variation in composition throughout the ingot, as affected by segregation, is of great importance, as are also the form and distribution of the voids that result from the gases evolved. It is because of this importance that the considerable literature in this field has accumulated. No attempt is made in the present paper to compile a bibliography of the excellent work that has already been done, as this has been adequately covered in the many excellent reports on the heterogeneity of steel ingots prepared by a joint committee and published by the Iron and Steel Institute.' From time to time, in any field of investigation new tools and new technique are developed, which make further progress possible. In the field with which this paper is concerned, this is true. The development of the vacuum-fusion method as a means of following oxygen segregation, and a technique for obtaining the volume and composition of the gases evolved during solidification, have opened the way to obtaining data by means of which some considerable progress has been realized in developing more of the detailed mechanisms of solidification and segregation in rimming-steel ingots. General Theory of Segregation The basic cause of segregation lies in the fact that the impurities are less soluble in solid than in liquid iron. The solid that forms from the impure liquid is more nearly pure than the liquid itself. If solidification proceeds slowly enough, or if the liquid and solid phases are maintained in contact with one another for a sufficient time, a condition of equilibrium is set up, which may be represented by a phase diagram. Portions of the

Jan 1, 1939

By Donald Barton

THE theory of gravitation is based on Newton's law that any two bodies exert a mutual attraction which is proportional to the product of their masses and inversely proportional to the square of the distance between them; i. e., A = K MM/R2 (1) where K is a constant, M and m are the respective masses of the two bodies, and R the distance between them. In the earth's gravitational system, the earth is one of the bodies; the other may be any body within or without the earth. In theoretical discussions and calculations in regard to gravity, that other body usually is taken as a unit of mass: in the C. G. S. system, a body of one gram in mass. GRAVITY AND LEVEL SURFACES Gravity is defined in geophysics as the force of attraction exerted by the earth, towards itself, on a body of unit mass. The intensity of gravity is usually expressed in dynes of force or in centimeters of acceleration. In geophysical work in America; most commonly it is expressed in dynes (per gram) with the "per gram" understood and not directly expressed. In geophysical work in Europe, most commonly it is expressed in centimeters per second per second (cm./sec.2) and less commonly merely as centimeter-gram-second units (C. G. S.). At sea level, the intensity of gravity amounts very nearly to 980 dynes. The vertical is the direction along which the attraction of gravity is exerted at any point. In most cases, it is very nearly, but not quite, perpendicular to the earth's surface. The path that would be taken by a body falling freely through space toward the earth is vertical at each point and may be spoken of also as "the vertical," or as the line of the vertical, or as a line of force of gravity. At the earth's surface it commonly is very nearly, but not quite, a straight line.

Jan 1, 1928

By M. H. Waxman, L. J. M. Smits

A simple physical model was used to develop an equation that relates the electrical conductivity of a water-saturatedshaly sand to the water conductivity and the cation-exchange capacity per unit pore volume of the rock. This equation fits both the experimental data of Hill and Milburn and data obtained recently on selected shaly sands with a wide range of cation-exchange capacities. This model was extended to cases where both oil and water are present in the shaly sand. This results in an additional expression, relating the resistivity ratio to water saturation, water conductivity and cation-exchange capacity per unit pore volume. The effect of shale content on the resistivity index - water saturation function is demonstrated by several numerical examples. INTRODUCTION A principal aim of well logging is to provide quantitative information concerning porosity and oil saturation of the permeable formations penetrated by the borehole. For clean sands, the relationships between measured physical quantities and porosity or saturation are well known. However, the presence of clay minerals greatly complicates log interpretation, particularly the electrical resistivity and SP logs, and considerably affects evaluation of hydrocarbon-bearing formations. The conductance and electrochemical behavior of shaly sands and their relation to log interpretation have been studied by many workers. wylliel and Lunch2 reviewed this work in some detail. Virtually all laboratory measurements of electrical resistivity and electrochemical potential of shaly sands published to date are the work of Hill and Milburn.3 Their measurements were made on about 300 cores covering a large variety of sedimentary rocks, and a wide range of equilibrating NaCl solution concentrations. Hill and Milburn described their conductivity data by an empirical equation in which the shaly sand conductivity Co was expressed as a function of the solution conductivity C and two parameters b and F01 . The quantity b was shown to be a measure of the effective clay content of the rock, being approximately proportional to the cation-exchange capacity of the rock divided by its pore volume. The latter ratio is designated as 9, in this paper and has the dimensions meq/ml or equiv/liter. Qv is identical with the term representing the concentration of fixed charges in the Meyer-Sieved and Teorel15 theory of permselective membrane behavior. F01 is a formation resistivity factor referred to a hypothetical equilibrating solution resistivity of 0.01 ohm m at 25C,* where clay effects presumably are minimized. F01 was correlated to porosity by an Archie-type equation.6 The Hill-Milburn equation describes their data with a standard deviation of approximately 1 percent and a maximum deviation of + 10 percent. Shaly sands behave as permselective cation-exchange membranes, their electrochemical efficiencies increasing with increasing clay content. The electrochemical potential data of Hill and Milburn were expressed graphically, and demonstrate that the membrane efficiency (or cation transport number) of these sands is a function only of the b value (i.e., Qv) and the respective salt concentrations of the two solutions forming the liquid junction in the sand. The diffusion potentials are not dependent on F01 or any parameter relating to the porosity or pore geometry of the rock. The Hill-Milburn resistivity equation correctly predicts a decreasing sand conductivity Co with decreasing solution conductivity C?. However, at some low value of C,, the calculated Co-C, function goes through a minimum; with further decrease in C?, the predicted sand conductivity increases sharply. As pointed out by Hill and Milburn, an increasing value of Co with decreasing C, is physically meaningless. Since this occurs below the range of practical values of C,, the usefulness of the empirical equation is not affected when

Jan 1, 1969

By R. O. Leach, O. W. Wagner

Because of unfavorable wetting conditions much residual oil is left when a porous material is Pushed by water. Methods suggested to change reservoir wetting to improve oil displncernrnt efficiency are generally expensitlr. The present 1aborator.y study was undertaken to gain an under.standinx of the factors which determine reservoir wettability, arid to find out if oil displacement efficiency might be improved by a wettahility change accomplished at low cost in on oil reservoir. Contact angle measurements were made on mineral surfaces using sevc.r~zl sets of reservoir oil and water samp1es. Results of the contact angle studies suggest that reservoir wetta-hility may he primarily determined by natural surface-active substances present in the reservoir fluids. The effect of changing sa1inity and pH of the water phase was studied. The re.suits suggest that gross changes in preferential wettability might be acc~o~npli.shed by injection of water containing simple chernicnls to alter pH or salinity in the reservoir. Such treatment could he much less expensive than injection of commercial surface-active agents. Waterflood tests have also been made using synthetic cores and oil and water having wening characteristics similar to those of reservoir fluids. Cores initially oil-wet were flooded in such a way that they were made prefermtial1y water-wct by the advancing flood water. This reversal in preferential wettability achieved greater oil displacement efficiency than when either oil-wet or water-wet conditions were maintained throughout the flood. For the systems studied, the higher the oil viscosity the greater the percentage improvement obtained over conventional waterflood recovery. This suggests that a flooding process making use of wettability-reversal may extend the oil viscosity range over which water flooding is attractive. Because a precise adjustment of reservoir wettability does not seem to be required, and because altering the pH or salinity in some reservoirs may be inexpensive, it appears that a waterflooding process employing wet-[ability-reversal could find .succesful field application. I NTRODUCTION The efficiency with which water will displace oil from a porous material is related to the nature of the capillary forces present. These in turn are controlled by the preferential wetting of the solid by the two fluids. Because of unfavorable wetting conditions, 30 per cent or more of the original oil in place may remain unrecovered in that portion of a reservoir flushed by water. This paper is concerned with the possibility of improving waterflood oil displacement efficiency by alterations in the wettability of the porous material. A laboratory study was made to gain a better understanding of the factors which control reservoir wettability, and to determine if the oil displacement efficiency could be improved by some inexpensive means of manipulating wettability of the porous medium. Contact angle measurements were made with several natural and synthetic oil, water and solid systems (1) to obtain a better understanding of how to duplicate reservoir wettability in the laboratory, and (2) to discover possible means for changing preferential wettability of natural reservoir systems. Flooding tests were also made in synthetic systems to determine if oil displacement efficiency could be improved by those wettability manipulations suggested by the contact angle measurements. Based on these studies a possible method for improving waterflood oil displacement efficiency is presented. This method involves causing an originally oil-wet porous material to become preferentially water-wet during the course of a water flood. The purpose of this paper is to present results of the laboratory studies. THEORY Rock surfaces in some oil reservoirs are believed to be covered with a firmly attached bituminous or other organic coating. Such surfaces would be preferentially oil-wet in the presence of both oil and water, regardless of composition of reservoir fluids. Other reservoirs are believed to contain rock surfaces not permanently coated with such materials, and which would be preferentially wet by water in the presence of water and oil free from surface-active substances. However, when the reservoir fluids do contain certain natural surface-active materials in sufficient quantity, rock surfaces acquire a degree of preferential oil wettability caused by adsorption of these natural surface-active materials on the solid. The equilibrium amount of these materials adsorbed per unit surface area is believed to depend upon their concentration in the bulk liquid phases.

By William Wraith

1. INTRODUCTION. AT the Washoe smelter,. Anaconda, Mont., the blister-copper from the converters is transferred, by means of a crane, to a refining-furnace,, in which it is brought to proper pitch by means of air and poles. From this furnace the refined copper, containing gold and silver, is poured into cast-iron molds placed on a platform-conveyor, giving an anode 36.75 in. long, 28 in. wide, and 21 in. thick. By reason of a disagreement between the smelter and the refinery, in reference to the silver-content of the anodes, it became necessary to investigate the methods of sampling used. II. SMELTER METHOD OF SAMPLING. At the smelter the sampling is done by " spotting " into water a small portion of the molten stream of copper as it flows from the furnace, by batting" the stream with a wooden paddle. The first sample is taken 30, min. after the pouring is started, three. other samples being taken at 1-hr. intervals, each sample weighing from 4 to 6 oz. The samples are dried, examined for particle's of burnt wood, screened on a 10-mesh screen of No. 8 wire to remove the fines, the oversize then screened on a 4-mesh screen of No. 20 wire to remove the coarse, the undersize of this screen being taken as the sample. Teh four portions thus obtained are thoroughly mixed and spli in half by passing over a 16-slot splitting-device, slots being 0.5 in. wide. One-half of the sample is sent to the laboratory for analysis and one-half kept as a duplicate. III. REFINERY METHOD OF SAMPLING. The method used at the refinery and also used in this investigation is the one developed by Dr. Edward Seller, of

Mar 1, 1910

By Fred C. Bond and

This paper is a continuation of two earlier papers,12 and presents new data on the grindability of various ores and other materials—the results of several years of intermittent research work on the nature of grinding and interpretation of test results. It is divided into five parts: 1. The tabulated results of several hundred grindability tests on a wide variety of ores. 2. A method of correcting screen analyses and calculating from them the surface and other properties. 3. A description of a new method of measuring the "surface energy" of an ore by pendulum impact tests. 4. Test results. 5. A general discussion of the test results and their application to grinding problems. 1. GRindability of Various Ores This part is a continuation of the paper listed as reference No. 1. The method of testing is described in detail in that paper. The sample to be tested is crushed to all through 6 mesh in rolls set at 1/16-in. opening in closed circuit with a screen. Of this sample 700 C.C. is ground dry in a laboratory ball mill under constant conditions of mill speed and ball charge in closed circuit with a screen of the desired size at 250 per cent circulating load. The mill is cylindrical, 12 by 12 in., and rotates at 70 r.p.m. It contains a charge of 285 iron balls weighing 20,125 grams and ranging from 1½ to ¾ in. in diameter. Each test is continued for a sufficient number of periods to establish equilibrium at 250 per cent circulating load, or until the composition of the circulating load is constant for successive periods. Tests are conducted at the mesh size to which the ore is to be ground in practice, and the results are expressed as the net production in grams of screen undersize per revolution of the mill. This is designated as the

Jan 1, 1939

By Fred C. Bond and

This paper is a continuation of two earlier papers,12 and presents new data on the grindability of various ores and other materials—the results of several years of intermittent research work on the nature of grinding and interpretation of test results. It is divided into five parts: 1. The tabulated results of several hundred grindability tests on a wide variety of ores. 2. A method of correcting screen analyses and calculating from them the surface and other properties. 3. A description of a new method of measuring the "surface energy" of an ore by pendulum impact tests. 4. Test results. 5. A general discussion of the test results and their application to grinding problems. 1. GRindability of Various Ores This part is a continuation of the paper listed as reference No. 1. The method of testing is described in detail in that paper. The sample to be tested is crushed to all through 6 mesh in rolls set at 1/16-in. opening in closed circuit with a screen. Of this sample 700 C.C. is ground dry in a laboratory ball mill under constant conditions of mill speed and ball charge in closed circuit with a screen of the desired size at 250 per cent circulating load. The mill is cylindrical, 12 by 12 in., and rotates at 70 r.p.m. It contains a charge of 285 iron balls weighing 20,125 grams and ranging from 1½ to ¾ in. in diameter. Each test is continued for a sufficient number of periods to establish equilibrium at 250 per cent circulating load, or until the composition of the circulating load is constant for successive periods. Tests are conducted at the mesh size to which the ore is to be ground in practice, and the results are expressed as the net production in grams of screen undersize per revolution of the mill. This is designated as the

Jan 1, 1939

By Morris E. Fine, Richard A. Kloske

The stress-strain beha1,ior in tension of Au-Ag alloy single crystals containing nominally 1,3, 5, 95, 97, and 9.9 at. pct Ag was studied uS strain role and lektlperalure down lo 4.2K. A slrain aging yield hob lc,rrs observed on aging under stress in the temperature range 30° lo 75°C. The species diffusing to the dislocation is thought to be a divacancy-solute complex wilh /he. solute then pinning the dislocation by short-Range ovdering and possibly Suzuki locking. At room tempevullcve the critical reso1ved shear stress .follo~c.s an empirical equation of the form tc = A +Bc' where A and B are 90 and 420 ,g per sy mm tor gold base alloys and 60 and 510 g p~r sq )11ttz .tor si1ver base alloys. This strengthening was attributed to a long-range size ejtect. The alloy slrenglliening at i.2'K is greafer than at room temperature. The additional atrloutzf was altribuled lo a uwak skovl-range i?~levacIion between the solute and dislocallon cove. The activation energy .tor deformation a/ 4.Z0h7 decreases on alloying. 11 increases irr other fee systetns. hi the 5 at. pcl Air-Ag- alloy in pmvlicular there is very extensive easy glide and lavge overshooting- of the synmetry line at 4.Z°K. There is also u sharp decrease in the vale of. strain hardenitlg near the widdle of stage II with the new rate bezng abold the sarne as tlzal In easy glide. This uws attributed to a sudden reduction of activity on the pvitrrarg sgstertr. In Au-Ag alloys the critical resolved shear stress Tc. at room temperature is essentially a parabolic function of atomic concentration:' the 50 at. pct Ag-50 at. pct Au alloy is about 10 times stronger than the pure metals. This strengthening occurs in spite of the similarity in valence and atomic size. Solid-solution strengthening in fcc metals is characteristically greater at low temperatures than at room temperature. In Ag-10 at. pct Au and Au-10 at. pet Ag; r, (20.4K)/Tc (300°K) is 2.3 and 2.5. respectively.- compared to 1.2 in pure silver.3 Suzuki' and Flinn5 explained the alloy strengthening at room temperature as a combination of Suzuki locking and short-range order hardening. The agreement between the computed and measured strengthening was very good: however, in Ag base-A1 alloys Hendrickson and Fine6 concluded that Suzuki locking resulted mainly in a yield drop effect. Recent reviews of the solid-solution strengthening in fcc metals by Fleischer2 and Haasen8, 9attributed the strengthening at room tenl-perature to the combined effect of atom nlisfit and change in shear modulus 011 the long-range stress field surrounding a dislocation. The parameter used by Fleischer was The shear tnoduli of Ag-0 to 6 at. pct Au alloys were measured by Pur-wins. Labusch. and Haasen.In While addition of 4 at. pct Au caused an appreciable increase in the C,, elastic constant. there was a decrease on increasing the solute to 6 at. pct Au: C,, and C :: were not measured in the 6 at. pct alloy. The greater solution hardening at low temperatures implies the presence of short-range interactions between the solute atoms and dislocations These include size and electronegativity effects. Whether the extra alloy strengthening at low temperatures is due to locking or friction hardening is still a controversy."".' In the present research the stress-strain behavior of Au-Ag single crystals containing 1 to 5 at. pct Ag and 1 to 5 at. pct Au was measured vs strain rate and temperature down to 4.2' K. Particular attention was paid to yield drop effects. These have not been previously reported. PROCEDURES The alloys were supplied by the Engelhard Industries. Inc.. as strips 0.050 by 0.250 by 12 in. The compositions are given in Table I. Single crystals were grown under static vacuum using a traveling molten zone technique. Crucibles shaped to the size of the strips were made of high-purity graphite prebaked for 24 hr at 1100°C in vacuum. The crucible and its charge were placed in

Jan 1, 1970

W. 0. HOTCHKISS,* Madison, Wis.-When we began to do geological field work in the Lake Superior region, we found a correlation in existence, and, as youngsters, accepted all that as settled. Both Mr. Allen and I, since that time, have seen a great many things that were not apparent nor visible to Van Hise, and those who worked with him; we realize now that the correlation was not final and that much remains to be determined concerning geology of the Lake Superior region. My attitude on this matter is that we should not publish an amended correlation as a final thing. We should avoid, in every way possible, foreclosing the minds of those who follow us in working in the geology of this region. As a matter of fact, no correlation can be final at present, because facts and data are accumulating so rapidly that every classification must be immediately modified to fit further observation. Consequently, my attitude in this matter would be, instead of saying that the iron formations of the Lake Superior region are all Middle Huronian, to say that there may be three Huronians-or four or five- we do not know. I believe it is better policy to hold to our present correlation. I do not believe there is any economic benefit to the mining man or the geologist working on problems relating to explorations for iron ore, that cannot be just as well solved by maintaining our present correlation, with a. wholesome idea of our lack of knowledge and the necessity for further detailed work. Then, if any new horizons are discovered in any particular range, the minds of the investigators will not be foreclosed because some one has said that all the iron formation is in the Middle so that there is no use looking elsewhere for it. There is use looking elsewhere, in many cases, as the ore deposits become exhausted.

Jan 1, 1920

By Stanley D. Michaelson, Norman Weisis

The purpose of beneficiation is to increase the economic value of an ore by elimination of waste rock or by separation of minerals that require separate reduction, without destroying the physical and chemical identity of the minerals. Flotation has replaced older methods of beneficiation to a very great ex- tent, nearly entirely in the case of the copper, lead, and zinc minerals and less completely in the case of such other minerals as iron, coal, and titanium. Flotation is also used to recover barite, fluorspar, feldspar, cement rock, spodumene, vermiculite, silica, beryl, and potash in the nonmetallic field, and cobalt, vanadium, germanium, antimony, mercury, molybdenum, manganese, nickel, gold and silver, cadmium, and bismuth for metals. The rapid growth of flotation to pre-eminence cannot be attributed to its low cost, because gravity, magnetic, and electrical methods may in some cases cost only half as much. But for ores containing finely disseminated minerals, these other methods are successful only in exceptional cases, for example the magnetic taconites or titanium-bearing sands. For low grade ores with coarse texture or spotty mineralization the advantages of low-cost gravity methods and highly efficient flotation are often combined, as in the beneficiation of coal and some ores of lead and zinc, phosphate, tungsten, and manganese. When an ore is responsive to either flotation or non-flotation concentration, or to combinations of the two, the choice depends upon cost of the process only when dealing with ores of low value; in other cases it is dictated by either the process efficiency or the product specification. Generally speaking, flotatio.1 is so efficient as compared with other methods of concentration that process cost is rarely an important factor in its selection. It is said, "The metal in the mill tailing has already been mined." Once the mining cost has been paid it doesn't increase total costs very much to do a thorough job of milling. With the exception of the few types of ores that are not amenable to flotation, the chief reason for preferring electrical and gravity methods to flotation may lie in the specification of the product. Flotation demands fine grinding, and specifications may not permit this with many nonmetallic ores or coal. Another reason is the size of investment-where capital is hard to obtain or the life of the property is short, the justification for a flotation plant may not exist, and one must be content to skim off the cream. y not exist, and one must be content to skim off the cream. Gravity processes often cost less than flotation because a large part of the waste rockcan be rejected without costly grinding, no chemicals are required,

Jan 1, 1962

By T. C. Boberg, R. B. Lantz

This paper presents a method for calculating the producing rate of a well as a function of time following steam stimulation. The calculations have proved valuable in both selecting wells for stimulation and in determining optimum treatment sizes. The heat transfer model accounts for cooling of the oil sand by both vertical and radial conduction. Heat losses for any number of productive sands separated by unproductive rock are calculated for the injection. shut-in and production phases of the cycle. The oil rate increase caused by viscosity reduction due to heating is calculated by steady-state radial flow equations. The response of successive cycles of steam injection can also be calculated with this method. Excellent agreement is shown between calculated and actual field results. Also included are the results of several reservoir and process variable studies. The method is best suited for wells producing from a multiplicity of thin sands where the bulk of the stimulated production comes from the unheated reservoir. The flow equations used neglect gravity drainage and saturation changes within the heated region. INTRODUCTION This paper presents a calculation method which can be used to predict the field performance of the cyclic steam stimulation process. The calculation method enables the engineer to select reservoirs that have favorable characteristics for steam stimulation and permits him to determine how much steam must be injected to achieve favorable stimulation. While the calculation represents a considerable simplification of physical reality and the results are subject to numerous assumptions which must be made about the reservoir, it has been found that realistic calculations can be made of individual well performance following steam injection. The duration of the stimulation effect will depend primarily on the rate at which the heated oil sand cools which, in turn, is determined by the rate at which energy is removed from the formation with the produced fluids and conducted from the heated oil sand to unproductive rock. A complete mathematical solution to this problem is a formidable task, and finite difference techniques would undoubtedly have to be used. The calculation method pre- sented here utilizes analytic solutions of simple related heat transfer and fluid flow problems. The method is sufficiently simplified that it can be used as a hand calculation, although the calculations are somewhat lengthy and laborious. For that reason, the analysis was programmed for an IBM 7044 digital computer. Well responses observed at the Quiriquire field in eastern Venezuela&apos; have been matched using this program after making suitable approximations for reservoir and wellbore conditions. One of the most valuable uses of this calculation method is to assess the effect of reservoir and proc-cess variables on the stimulation response. This paper contains results of several studies made of key reservoir and process parameters. Among the most important of these is the influence of prior wellbore permeability damage. If a well is severely damaged prior to stimulation, a higher stimulation response will be observed than if it is undamaged. If a portion of this damage is removed, a permanent rate improvement will occur. THEORY I)ES(:KJJ&apos;TION OF CALCULATION METHOD The process of cyclic steam stimulation is essentially one of reducing oil viscosity around the wellbore by heating for a limited distance out into the formation through the injection of steam. Suitable modifications of the calculation technique presented here can be made so that stimulation of wells by hot gas injection or in situ combustion can also be calculated. A schematic drawing of the heat transfer and fluid flow considerations included in the calculation method is shown in Fig. 1. In brief, the calculation assumes that the oil sand is uniformly and radially invaded by injected steam. For wells producing from several sands, each sand is assumed to be invaded to the same distance radially. In calculating the radius heated rn energy losses from the wellbore and conduction to impermeable rock adjacent to the producing sands are taken into account. After steam injection is stopped, heat conduction continues and oil sands with r < ra cool as previously unheated shale and oil sand at r > r, begin to warm. The effect of warming of oil sand out beyond r, has little effect on the oil production rate compared to the effect of cooling of the oil sand nearer the wellbore than ra. Thus, in computing the oil production rate, an idealized step function temperature distribution in the reservoir is assumed where the original temperature exists for r > rn and where an average elevated temperature exists for r < rn. The average temperature in the oil sand for the region r < rn is computed as a function of

Jan 1, 1967