Search Documents

By H. M. Beatty, T. L. Joseph, Gust Bitsianes

SUCCESSFUL blast-furnace operation depends upon securing an optimum balance between a number of important variables. This balance will vary somewhat from furnace to furnace in the same plant and with raw materials available in different plants. It is difficult to isolate the effect of any one variable unless it has a rather pronounced effect upon the efficiency of operation. The physical properties of iron ore and coke are known to affect the process, yet it is difficult to set up any definite yardstick by which these differences can be appraised. In recent years, whenever practicable, operators have taken steps to obtain better control over the absolute size and uniformity of size of the ore and coke. The size and physical character of the stone, however, have received comparatively little attention, emphasis being placed upon chemical composition, fluxing efficiency, and action as a desulphurizing agent. Since the stone occupies only about 10 per cent of the volume of the stock column, its influence upon permeability is less than that of the ore and the coke. The large pieces now used have a tendency to roll to the center and thus increase the permeability of this part of the stock column. Smaller pieces would be more effective in promoting the permeability of denser portions of the stock. The size and physical properties of blast- furnace stone are important also for reasons best understood by considering the results obtained by the crushing and the sizing of iron ore. Crushing ore to about 2 in. at Provo, Utah, and to about I in. in Alabama produced material somewhat less permeable to gases, even though sized. In spite of some sacrifice in permeability, the efficiency of the process was improved by crushing and sizing the ore, as indicated by a substantial saving in fuel and increased output. This saving in fuel is due in large measure to more thorough reduction of ore in the upper part of the furnace and to a corresponding decrease in the amount of carbon consumed prematurely above the tuyeres by the reaction CO2 + C = 2CO ? 70,080 B.t.u. [I] The physical properties of stone, its size and rate of calcination are important because they influence the rate at which C02 is released and the completeness of calcination before reaching a level in the furnace where the temperature does not exceed 1050°C. (1920°F.). Briefly, carbon dioxide from the limestone or from the reduction of ore may cause premature com- bustion of carbon above the tuyeres. Assuming that 1000 lb. of limestone is used per ton of pig iron, about 435 lb. of C02 will be liberated during calcination of a good grade of stone. If all this CO2 from the stone were to oxidize carbon prematurely, about 120 lb. would be consumed above the tuyeres in a heat-absorbing reaction. The amount of carbon thus consumed when a

Jan 1, 1942

By PHILIP N. MOORE

PHILIP NORTH MOORE was born on July 8, 1849, at Connersville, Ind. His father, a civil engineer, was descended from Henry Moore who came from Ireland in 1773 to live in Washington, Pa. Through his mother, Philip Moore was descended from John North, who came to America in 1635 and settled in Connecticut. The story of Mr. Moore's life as told by himself is given on pages 373-386 of T. A. Rickard's "Interviews with Mining Engineers." He studied at Miami University, where he gained the degree of A.B. in 1870, and A.M. in 1873. In 1920 his alma muter conferred on him the honorary degree of LL.D. He, as a special student, was a member of the class of 1872 at the School of Mines of Columbia University.

Jan 1, 1930

By Sherwin F. Kelly

THE joint meetings of the Mining Geology Committee and the Society of Economic Geologists proved to be deservedly popular, and the interesting papers drew an attendance which strained the capacity of one of the large meeting rooms.. As might be expected these days when even the Supreme Court can't keep away from the subject of gold, the discussions opened on Thursday morning with several papers devoted to questions of structural and mineralogical relationships of the deposits of this metal. The presentation of Ira B. Joralemon's paper, "Veins and Faults in the Bralorne Mine," by Reno Sales, elicited considerable discussion on the relation of mariposite to gold, and the situation of the gold deposits with respect -to the Coast Range batholith. H. V. Warren stated that lie had observed mariposite always to be associated with gold in this region, but that gold was not always associated with mariposite. He pointed out that there is a series of veins on the west side of the batholith with a different mineralogy that, because of their richness but small size could quite easily make good, small mines. John A. Dresser concurred in this, and said lie thought this region was one of great promise for the mining geologist. He also reported having found mariposite associated with gold values below commercial limits, in the Appalachian regions.

Jan 1, 1935

By A. H. Smallbone, R. Lathe

Considerable efforts have been expended to apply multiple regression techniques to quantitative determinations in x-ray fluorescence analysis. Multiple regression has been shown to be an effective method for correlating x-ray fluorescence intensities to elemental concentrations. Although many other techniques have been devised to solve the problem of matrix effects in x-ray fluorescence analysis, there are few as efficient in terms of storage requirement or ease of programming for digital computers as the multiple regression method. In the case of ore slurry, it has the additional advantage of allowing a unified approach to the problems of slurry density correction and matrix effect corrections. The data used in the present work were obtained with an on-stream x-ray analyzer capable of analyzing 15 slurry streams for as many as nine elements simultaneously. One of its fixed monochromators was set to accept scattered radiation at a discretely selected wavelength as a means of monitoring the slurry's pulp density. The data were reduced to obtain the correlation equations and a computer program combining slurry density with matrix corrections was written in FORTRAN IV to calculate concentrations.

Jan 8, 1969

By Charles A. Thomson

RECENTLY a prominent Brazilian' doctor wrote to an American friend: "I feel that cultural relations between the American and Brazilian people could be promoted in a very speedy and effective way by establishing contacts between men of the same professions. . . . A Brazilian mechanical engineer could be immediately interested in relations with American colleagues, even if he had never heard of Longfellow and was not interested in Stokowski's orchestra. . . . A large number of cultural ties could be established between specific groups of men who have already some common interest, and who, whenever they meet, can do something that naturally brings them closer, that is, `talk shop."' In appointing a committee on Inter-American Engineering Relations to cooperate with the Department of State in its program of fostering cultural relations with the other republics of this hemisphere, the American Engineering Council has taken a step which should lead to a greater sense of unity and fraternity among engineers of the Americas. That such unity and fraternity are part and parcel of the moral defense of the hemisphere is obvious. For years engineers of the United States have been traveling South and South-east to construct roads and bridges, dam rivers, harness waterfalls, build ports, install and operate mining equipment, and erect buildings and plants, often at the risk of life. Those in the teaching profession in this country have had as pupils a growing number of students from our neighboring republics whom they have sent back home trained in the most efficient engineering methods. In a sense, however, these relations with the other nations on this side of the globe have been haphazard and left to chance. Personal acquaintance among engineers has played its role but no organized attempt appears to have been made to take advantage of the natural relationship which geographical and historical factors should encourage.

Jan 1, 1940

By C. E. BOCKUSD

WHEN Mr. Bain asked me to lunch with you he requested that I say a few words as to how the Institute could be helpful to the bituminous coal industry. I feel like saying, "Thank you, what have you?" I do not want to trace in detail the story that is old already to many of you. On the other hand it does take some little stage-setting to illustrate what is the matter in the bituminous coal industry, a trouble that must some day be cured. There has been something over a century of bituminous coal production as a real business in this country. True, Joliet and Marquette discovered coal in Illinois in 1673, according to published accounts of their travels, and shortly thereafter Father Hennepin also found Illinois coal in 1689. Coal was mined near Richmond in 1750, and Richmond shipped coal to New York and Philadelphia in 1789. But it was not until 1838 that the production of bituminous coal in this country totaled a yearly output equal to the minimum for one class A mine today, for that was the first year that production exceeded 200,000 tons.

Jan 1, 1930

By R. R. Seeber

(Pittsburg Meeting, March, 1910.) IN the copper-mining district of northern Michigan a fair-sized mine usually operates two or more shafts along the strike of the lode, these shafts being usually at least 1,000 ft. apart. The tonnage to be hoisted from each shaft is large-from 13,000 to 25,000 tons per month. The hoisting-engines used are generally steam-driven, non-condensing, duplex engines with Corliss valves, supplied by steam from separate boiler-plants where the distance between shafts is great. In an attempt to centralize power-plants and secure central-station economies, the Winona Copper Co. installed an electric hoist of the Ilgner type, with Ward Leonard control. A brief description of this plant has already been published.1 The only point of variation from the simple Ilgner set lies in the connection of two generators to a single induction-motor by flexible couplings. These generators serve motors which operate hoisting-drums at separate shafts, viz., No. 4 shaft, Winona, and No. 1 shaft, King Philip. , The hoist for No. 4 shaft, is about 1,700 ft. from the power-plant, and in this building the motor-generator set is placed. No. 1 King Philip hoist is 1,500 ft. from the motor-generator set. The equipment of the motor-generator set is as follows: In the middle of the set is a 12-pole, 450-h-p., 600-rev. per min., 2,080-volt, three-phase, 60-cycle, variable-speed induction-motor, connected on each side to a 20-ton fly-wheel which is 10 ft. in diameter, and to a 6-pole, 170-kw, 575-volt, interpole, direct-current generator. On each side of the shaft is placed a separate exciter, which delivers current at 125 volts. The lubrication of the four main bearings that support the fly-wheels * Presented also, by mutual agreement, at the meeting of the American Institute of Electrical Engineers, New York, N. Y., Mar. 11, 1910. Engineering and Mining Journal, vol. lxxxviii., No. 3, p. 110 (July 17, 1909).

Sep 1, 1910

By AIME AIME

THE STANDARD herewith submitted is the result of several years of research and consideration by the A.I.M.E. Technical Committee on Milling Methods. In the early work of this committee it was found necessary to undertake the development of a standard laboratory method for screen testing of ores. During the research stages the desirability of having this standard, when completed, approved as American Standard was brought out. In accordance with this idea, its initiation as a project of the American Standards Association (then the American Engineering Standards Committee) was approved by the latter body and the A.I.M.E. designated as sponsor. In 1929, the A.S.A., on recommendations of its advisory committee, the Mining Standardization Correlating Committee), authorized the A.I.M.E. to be sole sponsor for this project. The personnel of the Institute's Committee on Milling Methods was then increased to make it thoroughly representative of all diversified interests in the mining field. Two years ago the standard was circulated and has been given wide distribution. Early in 1932 the committee voted unanimously, with 38 affirmative votes, that the standard be recommended to the Board of Directors of the Institute for submission to the American Standards Association for approval as American Recommended Practice. This was accordingly done, at the Feb. 1.6, 1932, meeting of the directors, and the American Standards Association approved the standard on July 6; 1.932, designating it as ASA M5-1932.

Jan 1, 1932

By AIME AIME

A CERTAIN area in the State of Indiana seems to be a breeding place for presidents and near president about eighteen miles southeast of Elwood is the little village of Daleville, and there, on April 9, 1890, John Robert Suman, newly elected President of the A.I.M.E., was born. It was not long before he migrated to California, however, where he went to the Los Angeles High School, then for two years to the University of Southern California, after which he went up to Berkeley

Jan 1, 1940

By Charles E. Parsons

One of the greatest factors in our industrial development is cheap and convenient power. Long-distance electrical transmission has now reached such a stage that it is feasible, and practicable, to utilize the water-power of the country which was heretofore too remote for consideration. In all of the changes of energy from its various sources to its electrical applications, water-power stands pre-eminent in point of economy. Power-users the world over have endeavored to utilize this force in preference to any other, and until long-distance transmission was found practicable it seemed that every available water-power in this section of the country was doing its full share for the benefit of mankind. The success of each great industrial development has been clue in a greater part to some one man one who is just a step in advance of the rest in his particular field; one who is able to grasp a situation and foresee possibilities; and, above all, one who has that indomitable pluck and perseverance which sees in each obstacle one more step toward success. Such a mail is Eugene L. Ashley, for it was through his efforts that the development of the greatest power on the Hudson river was made possible. For several years prior to 1897 the various properties along the river between Glens Falls and Palmer Falls were in the hands of speculators. These men knew the value of waterrights, but they had not the ability to assemble the properties and finance such an undertaking. In 1897 Mr. Ashley began buying these water-rights, and, after two years of litigation, title mas secured to all of the properties along each side of the river, and the Hudson River Water-Power Company was organized to construct a dam and transmit power to the surrounding cities and villages. A contract was let for a dam

Jan 1, 1904

By PAUL P. ZElGLER

Rapid growth of the aluminum industry continued through 1948 with an acute shortage of the metal in all forms marking the year. Estimates based on shipments made during the first nine months indicate that, in 1948, the industry shipped more than two billion pounds of aluminum products or roughly four times the amount shipped in the greatest peacetime year prior to the war. The rapid expansion of the aluminum industry is particularly reflected in the production of sheet. Last year, the industry as a whole shipped an estimated 40 per cent more sheet than was produced in the peak war year of 1944.

Jan 1, 1949

By E. S. Grumell

The correct sampling of coal and coke is becoming important to an ever increasing number of producers and consumers. This, therefore, may be an opportune moment to examine where we stand with regard to existing and proposed methods. In this paper an attempt will be made to review, as briefly as possible, some of the considerable amount of painstaking research which has been done in the last 10 years, and which has unquestionably led to a much better understanding of the subject. In so doing we shall try, on the one hand, to make clear where substantial progress has been made, and on the other hand, to draw attention to points that require further investigation. The paper is divided into sections in order to emphasize the major divisions of the subject; further, in order to retain this emphasis, detailed consideration of some of the points has been relegated to appendixes. No attempt has been made to give a complete survey of the literature, as this has already been done by L. A. Bushell.2 The following abbreviations will be used: A.E., average error; P.E., probable error; S.W.R., size-weight ratio; B.S.I., British Standards Institution. Section 1.—Cost It has often been stated that the cost of sampling should bear some relationship to the value of the product, and since coal is a relatively cheap raw material it would be a major error to specify, for ordinary commercial purposes, elaborate and costly methods of sampling which nobody would adopt. Specifications must be of such a nature that they will be used. We believe that one of the achievements of the last 10 years has been to reduce the cost of sampling. There is, however, another point to be considered; via., that the cost of sampling should bear some relationship to the value of the investigation. Correct sampling is a cog (possibly a small one) in the wheel

Jan 1, 1940

By E. S. Grumell

The correct sampling of coal and coke is becoming important to an ever increasing number of producers and consumers. This, therefore, may be an opportune moment to examine where we stand with regard to existing and proposed methods. In this paper an attempt will be made to review, as briefly as possible, some of the considerable amount of painstaking research which has been done in the last 10 years, and which has unquestionably led to a much better understanding of the subject. In so doing we shall try, on the one hand, to make clear where substantial progress has been made, and on the other hand, to draw attention to points that require further investigation. The paper is divided into sections in order to emphasize the major divisions of the subject; further, in order to retain this emphasis, detailed consideration of some of the points has been relegated to appendixes. No attempt has been made to give a complete survey of the literature, as this has already been done by L. A. Bushell.2 The following abbreviations will be used: A.E., average error; P.E., probable error; S.W.R., size-weight ratio; B.S.I., British Standards Institution. Section 1.—Cost It has often been stated that the cost of sampling should bear some relationship to the value of the product, and since coal is a relatively cheap raw material it would be a major error to specify, for ordinary commercial purposes, elaborate and costly methods of sampling which nobody would adopt. Specifications must be of such a nature that they will be used. We believe that one of the achievements of the last 10 years has been to reduce the cost of sampling. There is, however, another point to be considered; via., that the cost of sampling should bear some relationship to the value of the investigation. Correct sampling is a cog (possibly a small one) in the wheel

Jan 1, 1940

By Robert Linton

SPECIFICATIONS for clays serving raw materials in the ceramic industry usually contain the following items: (1) Chemical analysis, sometimes with mineralogical structure determined by microscopic investigation. (2) Maturing temperature and firing range, usually expressed in terms of pyrometric cone equivalent. (3) Shrinkage (drying and firing shrinkage separately). (4) Degree of plasticity. (5) Color after firing. Clays may be classified, according to the purpose of the classification, in several different ways, based on (1) Geological occurrence-transported, altered An place, indurated (shales). (2) Physical properties-plastic (bonding clays, ball clays) and nonplastic (flint clays, kaolins or china clays, bone clays). (3) Color. (4) Use. A common classification of clays for commercial designation, and one fol-

Jan 1, 1936

By Wilbur E. Sanders

AT some period during the operation of metalliferous and other commercially valuable mineral-deposits in connection with their underground mining, when the developments therein have become so extensive that their description is tedious and confusing, some scheme for naming or numbering the various workings and their parts is necessary for convenience of ; reference.. A simple and symmetrical yet expansive system of classification must be devised, one that is capable of being extended to cover all possible exigencies and conditions of future operations within the property. Such a scheme, properly arranged, greatly simplifies communication between the various departments of the mining business, as, for instance, between the administrative and the operating departments of the concern, and is of the greatest assistance to the officers of the mine in enabling them to locate and describe particular points and parts of workings and specific kinds of work. Again, in the proper segregation and differentiation of mine-accounts, when they are carried out with that detail which will furnish ready information concerning the cost of a particular piece of work, or the various items and totals of expense connected with the, development,, operation and repair of each or all of the mine-workings, some such method of designation becomes a necessity. . Moreover, such a plan is admirably adapted to the needs of the mining engineer, who, in connection with his reports upon mining-properties, is sometimes required, in his descriptions of certain blocks of ore, to locate lists of assays of samples taken from many and various places, and to designate workings and parts of workings that are located in different parts of the mine, sometimes at points wide apart.

May 1, 1906

By Maxwell Gensamer, Vsevolod N. Krivobok

It is generally recognized that "low temperatures" have a definite effect on the properties of metals and alloys. Furthermore, it is also generally understood that the effect is decidedly adverse. The possibility that the same low-temperature treatment might be employed for the purpose of improving certain properties of the alloys has received less attention until recently, and the experimental and theoretical knowledge consequently is meager. The effect of low temperatures may be studied in two ways: by studying such properties as tensile strength, hardpess, impact resistance, etc., at low temperature, and by studying the properties of alloys at room temperature after these alloys have been subjected to a low-temperature treatment. Even in the latter case, certain properties will differ materially from the same properties obtained on identical material but without cold treatment. In other words, subjecting alloys to cold treatment results in an irreversible change in mechanical properties. Changes of this character are usually indications of the appearance of a new phase or phases, and would be likely to occur in alloys which, either by virtue of their composition or by heat treatment, are retained at room temperature in a metastable condition. Consequently, studies of the effect of low temperatures logically should be conducted from the physicochemical point of view, since the results of such studies not only would furnish metallurgists with interesting theoretical data but would clearly indicate the classes of alloys that would hold promise of improvement, and, possibly, of new applications. As the present investmigation deals with chromium and chromium-nickel alloys of iron of the stainless variety, it has been thought desirable to present the data concerning low-temperature properties of these alloys, available from the most recent and most comprehensive work of H. S. Russell.l A summary of these data is given in Table 1. The data are confined to a limited number of alloys of the type dealt with in the present

Jan 1, 1931

By Norman P. Goss

It is generally agreed that cold-working mechanically refines the grains into smaller fragments and with continued working these are oriented with certain crystallographic directions bearing a relation to the direction in which the metal is worked. Some of the energy expended on the metal during plastic deformation appears in the form of heat, but a very small portion remains in the metal as stored energy. The entropy, specific heat capacity, temperature at which recrystallization will just begin, density, ductility, elasticity, tensile strength, and resistance to corrosion are affected. These properties have been studied extensively and some of the changes in the physical properties due to cold-working were attributed to lattice distortion.l-8 The broadening of the Ka lines on the X-ray diffraction diagrams of plastically deformed metals is believed to indicate lattice distortion, and consequently the existence of internal stresses. The evidence supporting this theory rests solely upon the observed experimental fact that the diffraction lines are broadened and the Ka doublets are completely diffused. Elam9 has reviewed the matter of lattice distortion in relationship to the hardening of metals by plastic deformation. The X-ray diagrams of plastically deformed metals differ in general from annealed metals. The hardening of a metal was believed due to lattice distortion.9 The resolution of the doublet is lost when a metal is cold-worked and the Laue spots are elongated. At one time this elongation was thought to indicate the elastic bending of the crystal planes. However, more careful work showed that the asterism was due to new orientations developed within the fragmented grains during plastic deformation. Some theories attributed the hardening to fragmentation of the grains into smaller units. Jeffries and Archer,ll after carefully considering the problem of work-hardening from many angles, came to the conclusion that cold-working mechanically refines the grains into smaller crystal fragments, some of which at least differ in orientation from the parent grain. The increase in

Jan 1, 1940

By Norman P. Goss

It is generally agreed that cold-working mechanically refines the grains into smaller fragments and with continued working these are oriented with certain crystallographic directions bearing a relation to the direction in which the metal is worked. Some of the energy expended on the metal during plastic deformation appears in the form of heat, but a very small portion remains in the metal as stored energy. The entropy, specific heat capacity, temperature at which recrystallization will just begin, density, ductility, elasticity, tensile strength, and resistance to corrosion are affected. These properties have been studied extensively and some of the changes in the physical properties due to cold-working were attributed to lattice distortion.l-8 The broadening of the Ka lines on the X-ray diffraction diagrams of plastically deformed metals is believed to indicate lattice distortion, and consequently the existence of internal stresses. The evidence supporting this theory rests solely upon the observed experimental fact that the diffraction lines are broadened and the Ka doublets are completely diffused. Elam9 has reviewed the matter of lattice distortion in relationship to the hardening of metals by plastic deformation. The X-ray diagrams of plastically deformed metals differ in general from annealed metals. The hardening of a metal was believed due to lattice distortion.9 The resolution of the doublet is lost when a metal is cold-worked and the Laue spots are elongated. At one time this elongation was thought to indicate the elastic bending of the crystal planes. However, more careful work showed that the asterism was due to new orientations developed within the fragmented grains during plastic deformation. Some theories attributed the hardening to fragmentation of the grains into smaller units. Jeffries and Archer,ll after carefully considering the problem of work-hardening from many angles, came to the conclusion that cold-working mechanically refines the grains into smaller crystal fragments, some of which at least differ in orientation from the parent grain. The increase in

Jan 1, 1940

By R. M. Hudson

A study has been made of the decarburization of low-carbon sheet steels at temperatures from 1100" to 1475°F in mixtures containing hydrogen, nitrogen, water vapor, and in some instances carbon monoxide. Decarburization occurs principally by the reaction C (in steel) + H20 = CO + H2 and follows a first-order rate law. The decarburization rate appreciably increases with an increase in temperature up to about 1325°F, but the increase in rate is small with fur- Use of a dry hydrogen atmosphere results in a relatively slow decarburization of steel and use of a wet hydrogen atmosphere results in relatively rapid decarburization. It is now generally recognized' that the reaction C (in steel) + H2O = H2 + CO [l] accounts for most of the decarburization that occurs in wet hydrogen-containing atmospheres. The present article is concerned with the decarburization of low-carbon sheet steel in H2-N2 atmospheres ther increase in temperature. The limiting rate of decarburization can be predicted from a knowledge of the solid solubility and diffusivity of carbon and this rate is approached as the water-vapor content of an atmosphere is increased. Hydrogen contents above about 8 pct are beneficial only in that they permit higher levels of water vapor to be used without oxidation of the steel. A buildup of CO in the atmosphere lowers the rate of decarburization. containing various amounts of water vapor and carbon monoxide. The effectiveness of these atmospheres and the influence of temperature on decarburization rate will be considered. EXPERIMENTAL WORK The chemical compositions of the three steels used in decarburization-rate studies are listed in Table I. Steel A was a commercially hot-rolled rimmed steel that was cold-reduced at the Laboratory to furnish specimens 0.025, 0.041, and 0.059 in. thick. Most of the experiments in which this steel was used were made on the 0.041-in.-thick material. Steel B and Steel C were cut from 0.010-in.-thick commercially cold-reduced coils that were

Jan 1, 1963

By J. J. Egan, A. B. Kinzel

Much work has been done recently in an attempt to analyze the physicochemical mechanism involved in the production of steel by the open-hearth process. This has resulted in reducing the process to a series of interrelated phenomena obeying the usual laws of mass action and diffusion. Of these, the reaction of the iron oxide and carbon in the molten steel is of most interest from a technical point of view as it constitutes the main action in the usual steelmaking processes. A. L. Feild' has formulated a basic differential equation expressing the open-hearth reactions and Herty has done considerable experimental work on the determination of a number of constants involved in the basic open-hearth reaction. In considering the application of the law of mass action to the reaction FeO + C + CO + Fe, the iron will be taken as constant, as is the case in the open hearth and the carbon monoxide pressure will be assumed constant at one atmosphere. From this xy = m at equilibrium, where x is the percentage weight of carbon, y percentage weight of iron oxide and m the weight-concentration equilibrium constant. While it is customary for physical chemists to express equilibrium constants in terms of molar concentrations, the constant is here expressed as the product of the percentage-weight concentrations for ease of comparison with the constants quoted by Herty and by Beild, and for more ready applicability to the open-hearth reactions. Herty and his associates have attempted to calculate the value of this constant from data on open-hearth heats. So many variables affect these results that an adequate calculation presents very great difficulties. A value of 4 X lop2 was first arrived at, but this was later changed to 1.6 X 10-2. Feild, in order-to illustrate the operation of the differential equation of the open hearth, has assumed a value considerably lower than Herty's, namely, 1.0 X 10-2, the largest value consistent with certain theoretical

Jan 1, 1929