Search Documents

By I. R. Kramer

The delay time for single crystals of iron, zinc, and pre-strained aluminum was measured under conditions of high-speed deformation. The delay time of aluminum was found to be affected by the orientation of the crystal. Under the dynamic conditions employed, tile calculated "activated volume" term appears to be very small for the three metals studied. IN a previous paper,1 it was shown that under dynamic testing conditions at 78° K, there was a delayed yield in single crystals of aluminum and copper which had been cold-worked prior to testing. The experimental results also indicated that the delay-time effect was not due to the interaction of dislocations with impurity atoms or vacancies, but rather to a dislocation-dislocation interaction since aluminum which has not been prestrained shows no delay-time phenomenon. In this paper, some data are reported on the effects of orientation on the delay time of aluminum single crystals; the delay time of zinc single crystals saturated with nitrogen and the delay time of iron single crystals also were measured. EXPERIMENTAL PROCEDURE Aluminum (99.997 pct) and zinc (99.999 pct) crystals, 1/2 in. in diam and 8 in. long were grown by the Bridgman technique. The iron single crystal was supplied by Dr. R. Maddin. The zinc crystals containing nitrogen were prepared by melting high-purity zinc in a graphite crucible and the nitrogen was introduced by additions of ammonium chloride. The liquid zinc was then drawn up into glass tubes of 1/2 in. diam and allowed to solidify. The rods were cooled to room temperature before the transfer to the mold for conversion into single crystals. The orientation of all specimens was determined by the Laue' back-reflection technique, Fig. 2 and Table I. To prepare for the delay-time measurements, the crystals were cut with a fine jewelers saw and the ends carefully machined. The specimens then were electrolytic ally polished to remove the cold-worked metal, mounted in a special fixture and hand-lapped. As a final step, the crystals were annealed in evacuated tubes. Specimens of aluminum crystals, Nos. 24 and 26, were compressed 0.5 and 2 pct, respectively, in the direction of the later impact. The zinc specimens were aged at 50°C for 15 min, In the case of iron, only two specimens could be obtained. To obtain sufficient data, it was necessary to resort to a reaging treatment. After each delay-time test, the specimens were aged at 65° C for 100 min. This treatment, according to Clark,2 is sufficient to restore the original delay time. It is believed that although the specimens were plastically deformed approximately 10-4 pct, after each test the delay-time values are reliable. The delay-time measurements were made in an apparatus similar to that described previously.' Single crystals approximately 1 in. long and having a diameter of 1/2 in. were placed in a pendulum which consisted of a bar 1/2 in. in diam and 8 ft long, designed with a crystal holder to accommodate the specimen at low temperatures. The crystal was held at a position 2 ft from the front part of the pendulum. This portion of the apparatus was supported on a fine molybdenum wire. A projectile bar of the same diameter and length comprised the other portion of the apparatus. This bar was supported on

Jan 1, 1962

BETWEEN the third and twentieth days of November, 1903, six intensely interesting letters were mailed from Santiago, Chile, addressed to "Mr. William Braden, Consulting Mining Engineer, 71 Broadway, New York City." The subject of these communications, referred to as the "Rancagua mines," was a copper property situated in the high. Andes; and the writer was Marco Chiapponi, an Italian mining engineer. Many a letter has been written about potential mines and prospects, good and bad, situated in all parts of the world; but few of them combine the shrewdness, sincerity, naïveté, and salesmanship that appear in these fascinating letters by Chiapponi. In 1894, Mr. Braden, as a young man twenty-three years old, had gone to Santiago to look after the erection and operation of some mining machinery that was to be exhibited at the International Mining Exposition. Not the least important of his purposes was to get acquainted at first hand with the mines and mining men of Chile, which ranked at the time (as it does today) second to the United States as a copper-producing country. It happened that a dispute arose regarding charges for certain construction work done in connection with young Braden's exhibit. Finally, arbitration was agreed upon and the Chilean exposition officials proposed Se[n]or Marco Chiapponi as a fair-minded neutral to decide the question. This he did in a manner satisfactory to both sides, and subsequently he and Mr. Braden became good friends. Nine years later Braden wrote to Chiapponi inquiring as to certain matters connected with the Corocoro copper mines in Bolivia. It was to this letter that Chiapponi refers in his letter of November 3, from which the following are some extracts,

Jan 1, 1933

The following advertisements show the contemporary view of the value of coal on a tract, usually as compared with farming advantages of several kinds. Fayette Gazette and Union Advertiser, February 10, 1798: "For Sale in Washington twp., Fayette Co., 211 acres of land whereon is a good new grist merchant mill, a good stone dam, and a house for the miller, about two acres of bottom, cleared and fenced, an excellent coal bank and saw-mill seat unimproved." Pittsburgh Gazette, March 19 and 26, 1802: Ads. offering for sale two properties, one of 38 acres, "together with a Coal Pitt and Lime Quarry, lying on the Monongahela side of Grant's Hill, and within one mile and a half of Pittsburgh," and the other two tracts of 700 acres on "Racoon creek, contiguous to which is a valuable limestone quarry, and a quarry of building stone, also plenty of stone coal." Pittsburgh Gazette, Oct. 8, 1802: A farm between Pittsburgh and Greensburg "with house, barn and a Smith shop-also, a fine sugar camp, and a Coal Bank within sight of the house," was offered for sale. The Farmers Register, Greensburg, Pa., March 13, 1802: An advertisement of a "plantation, six miles from Greensburg, there are two coal banks on it, one at each end of the place." The Commonwealth, Pittsburgh, Aug. 4,1805: A number of lots were laid off on Saw Mill Run, nearly opposite the first opening made on the Pittsburgh seam. They were from two to twenty acres each "and a great quantity of Limestone and stone coal." Pittsburgh Gazette, Aug. 9, Sept. 6, Sept. 27, Oct. 4, 1811; The Commonwealth, Aug. 19, 1811: Five tracts were advertised that contained coal. One had "fine springs and an inexhaustible mine of coal;" one, "excellent sugar camps, coal banks and limestone and a good mill seat;" one, "good sugar camps, an excellent coal bank and an elegant seat for a distillery;" another, a tract of 45,000 acres in Allegheny and Butler Counties affording "stone coal and iron ore, and seats for water works;" and the last a tract on Beck's Run, four miles from Pittsburgh "and a coal pit opened about one fourth of a mile from the river." The Mercury, Pittsburgh, April 8, Jan. 14, Feb. 11, 1813; Pittsburgh Gazette, April 16, Dec. 3, 1813: These tracts were advertised during the year in the vicinity of the city. One had "a good sugar camp, woodland and plenty of coal;" another, "a sugar camp and a coal bank on the premises;" while the others were "well timbered or well watered and had excellent stone coal." The Mercury, Pittsburgh, Feb. 2, 1814: A farm was offered for sale on the headwaters of Robinson's Run, in Washington County, four miles from Burgettstown, containing 60 acres, "a young bearing orchard,... a coal bank and a good sugar camp." Genius of Liberty and Fayette Advertiser, Uniontown, Pa., March 2, 1814, carried an advertisement of a sale of lots in the new town of Perriopolis; "the quantity and quality of the clay, sand and salt licks, near the premises, together with the timber and abundance of .stone coals The town of Perriopolis was situated upon a . farm at one time belonging to Washington.

Jan 1, 1942

By W. J. Joslin

The frontal-advance equation can determine how the fluid withdrawal rate and subsurface operating pressure influence oil recovery from pressure-maintained reservoirs having characteristics favorable for efficient vertical segregation. For effective vertical segregation in formations having low dip angles, the requirements are: thick, massive sands, low viscosity oil and high vertical permeability with few discontinuous shale members. This approach has been successfully applied to the LL-370, which is a massive Eocene sandstone reservoir containing crude with an average gravity of 26" APT, a dip of only 3" and vertical permeability of ½ darcy. The average gas cap saturation was calculated for various rates of vertical gas-oil contact movement corresponding to a wide range of reservoir producing rates. This method also evaluated the effect of different pressure maintenance levels on oil recovery. Applicability of this procedure for calculating the present oil saturation in the LL-370 gas cap has been substantiated from field performance, where the oil saturation was computed by comparing oil recovery with the gas cap volume vacated. INTRODUCTION During the natural depletion history of the LL-370 reservoir, located in Lake Maracaibo, Venezuela, excellent vertical segregation resulted in the formation of a thin gas zone over a substantial portion of the oil-productive area. Subsequently, gas injection forced this thin gas-saturated zone slowly downward, reducing the oil saturation in the gas cap to a low value. The oil recovery has been raised considerably above earlier predictions where vertical segregation effects were under-estimated. In order to determine the maximum efficient producing rate and optimum operating pressure for this reservoir, a vertical gas frontal-advance analysis has been made through application of the fractional flow equation. LL-370 RESERVOIR CHARACTERISTICS The reservoir consists of a truncated monocline of massive. highly-permeable Eocene sandstone, called the B-b formation, covering an area of more than 13,500 acres. The original oil in place was 2.17 billion STB. Internal non-sealing faults subdivide the structure into four blocks called the B-6-x.6, 10, 11 and 13, which are effectively bounded by major faulting on the flanks, an unconformity updip to the west, and an immobile aquifer to the southeast. The producing formation occurs at an average depth of 5,250 ft subsea and has a closure of more than 1,500 ft. A typical producing section has a net oil sand thickness of 170 ft. Scattered throughout the section are a few randomly-positioned shale lenses which increase in thickness and areal extent downdip. The reservoir rock and fluid properties vary with depth. The permeability and produced oil gravity are 1600 md and 28" API at the top, compared to 300 md and 18° API at the water-oil contact. The productivity of updip wells is, therefore, much higher than the reservoir average. The reservoir oil was originally saturated at the crest, grading to a slight degree of undersaturation at the water-oil contact. There was no original gas cap; and material balance and the field performance indicate no water influx. Except for the northern B-6-x.6 block, the fluid and rock properties have already been published.' Average LL-370 reservoir properties are shown in Table 1. RESERVOIR PERFORMANCE UNDER NATURAL DEPLETION Fig. 1 shows production performance from 1939 to date. Early development was gradual, with 30 wells pro-

Jan 1, 1965

By Albert F. J. Bordeaux

The following general survey of the character and present condition of the silver-mines of Mexico, though not offered as a detailed treatise, has been prepared with care, is believed to be generally up-to-date, and is offered as a summary which may be found useful by mining engineers. For several centuries Mexico has ranked first anlong the silver-producing countries. It is now second as a copper-producer, and seventh as a gold-producer, with a fast-increasing output every year. The total amount of capital invested in its mining- and smelting-works exceeds $250,000,000, while the value of the yearly metallic production is $160,000,000. There are more than 20,000 recorded mining properties. The silver-mines of Mexico represent deposits of three principal classes: (1) veins and stock-works in eruptive rocks; (2) fissure-veins crossing the crystalline schists, granite, diorite, etc.; and (3) veins and replacement-deposits in limestone. The true fissure-veins in some districts contain (in value) vol. xxr1x.—22

Jan 1, 1909

By Ronald E. Versaw

Environmental legislation, both existing and proposed, requires that mills, tailings dams, evaporation ponds, and related processing facilities be located, constructed, and operated within stringent guidelines. An early step in planning a new processing facility is performing a site selection study in which topographic, hydrologic, geotechnical, and environmental parameters are evaluated for several alternate sites. Once a site is selected, then an environmental report, including a description of the proposed action, alternatives, baseline surveys, and discussions of potential environmental impacts, mitigation measures and monitoring programs is required. The federal legislation, siting studies, and environmental studies (along with the implications of these as they affect design) are discussed. In addition, costs for performing these studies and implementing control of effluents are discussed.

Jan 1, 1978

By George Mansfield

INTEREST in the reserves of phosphate rock in the United States and their proper conservation has recently been aroused by hearings held in different parts of the country by the "Joint Committee to investigate the adequacy and use of phosphate resources of the United States." This committee was appointed within a few days after a Presidential message to Congress on the same subject, dated May 20, 1938, and began to function almost immediately. Hearings were held in Washington, D. C., Pocatello, Ida., Wilson Dam, Ala., Knoxville, Tenn., and Lake-land, Fla. The resulting testimony, when published, comprised a volume of 1182 pages.1 At the earlier hearings held in Washington and Idaho the seeming disparity between the great reserves of the West and the smaller reserves in the East led to some suggestions as to the desirability of curtailing or even prohibiting the exportation of phosphate rock so that eastern pro-ducers, becoming alarmed, cooperated in making available for the use of the committee information hitherto closely guarded. This informa-tion has provided an opportunity for new studies by official agencies, for a restatement of the reserves of Florida and Tennessee, and for some modification of figures for the Western States. The writer, representing the Federal Geological Survey, was given free access to the Florida material and has prepared for publication a report,2 some features of which are summarized in this paper. The Tennessee material was studied by Dr. G. I. Whitlatch,3 of the Tennessee Division of Geology. Prof. J. Stewart Williams,4 of the Utah State Agricultural College at Logan, has published a recent study of the phosphate resources of Utah and the writer has given some further study to reserves of western phosphate from the viewpoint of including material of lower grade than that hitherto considered.

Jan 1, 1940

By R. B. Campbell

One of the three power plants that will be in the Curecanti Unit of the Bureau of Reclamation's Colorado River Storage Project is the power plant at Morrow Point Dam. Presently under construction, the Morrow Point Power Plant is between Gunnison and Montrose on the Gunnison River in west-central Colorado. (Fig. 1). Morrow Point Dam will be a thin, double-curvature, concrete-arch dam, 465 ft high and will impound 120,000 acre-ft of water. Two 60,000-kw hydroelectric generators will be housed in an underground power plant in the left abutment just down- stream from the dam. The power-plant chamber will be an unlined opening 205.5 ft long, 57 ft wide and 65 to 134 ft high. The arch-type roof with a rise-to-span ratio of 1 to 4 will be supported with rock bolts and chain link fence. A description and discussion of the design considerations for the power-plant opening and rock bolt design are given by William H. Wolf, Gilbert L. Brown, and Ernest D. Morgan in "Morrow Point Under- ground Powerplant," ASCE Power Division Specialty Conference, Denver Colorado, August 18-20, 1965. The Morrow Point site is in a moderately active region of mild earth- quakes, as evidenced by recent earthquakes in 1960 and 1962. Therefore, the Bureau of Reclamation undertook an investigation of the effects on the underground power-plant chamber when subjected to an earthquake. The art of earthquake engineering has been directed primarily at developing methods of analyzing the nature of ground surface motions and designing surface structures to resist damage from vibrations impressed on the structure by the ground motions. The mechanism of straining an underground cavity by an earthquake

Jan 1, 1968

By Daniel N. Beshers, Ralph H. Condit

An expression for the diffusion coefficient of inlerstitial atoms in the bcc lattice is derived which takes account of jumps between tetrahedral and octahedral interstices. The results are applied to the case of carbon diffusion in iron to find values for jump frequencies of the types, octahedral-tetrahedral, tetra-hedral-tetrahedral, and tetrahedral-octahedral. ThERE has been renewed discussion1-5 concerning the mechanism of diffusion of interstitial atoms in the bcc lattice. This lattice has both octahedral and tetrahedral interstices, and it has been pointed out that the interstitial atoms may make jumps of the octahedral-octahedral type, hereafter called o-o, octahedral-tetrahedral, o-t, and tetrahedral-tetrahedral, t-t. Doubt has been cast on the applicability of snoek's8 model for internal friction to some interstitial migrations in bcc lattices wherein he proposed 0-0 jumps as the principal mechanism of migration. Also, the anomalous excess diffusion of carbon in iron at high temperatures4 has been ascribed to t-t jumps,2,3 even though the sites normally occupied are octahedral. In this paper an expression is derived for the diffusion coefficient, taking account of the three types of jump mentioned. The relationship of the coefficient to the corresponding internal friction relaxation time is found for the limiting case corresponding to Snoek's model. These results are applied to the case of carbon in iron. In Fig. 1, the structure is shown with the locations of the interstices. Each o site has four t site neighbors coplanar with it, and each t site lies halfway between two o sites. There are four t site first neighbors of a t site lying at the vertices of a tetrahedron. Let the average fraction of atoms occupying o sites and t sites be No and Nt, respectively. Since there are six o and twelve t interstices per unit cell having a lattice parameter, a, the concentration of interstitial atoms will It will be assumed that three types of jumps may be distinguished, t — t, t — o, o — t,for which the jump

Jan 1, 1968

By John Buch

NEARLY 25 years ago operating officials in the northern anthracite field were confronted with the problem of profitably mining virgin beds of thin coal (those 48 in. and under) or destroying them by mining under-lying thick beds. To solve this problem costly hand-mining methods were replaced by cheaper mechanical methods, which eliminated the need for the lifting of bottom or the brushing of top in excessive quantities, which was essential if proper height for hand loading' was to be provided. During this period long-face mining was an outstanding development. In its favor in comparison with any other method were the ease with which undercutting machines could be used, a differential in powder cost of about fifteen cents per ton in favor of this method over mining from a solid chamber or pillar face, and a greater production per day from a single working place, resulting in lower capital expenditures for a given total production, closer supervision and lower transportation cost. The long faces were drilled by jackhammer and undercut by machines. The coal from the cut was loaded into mine cars placed on the gangway road by means of a double-drum mechanical scraper engine and a mechan-ical V-type scoop. A tugger hoist was used to spot empty cars at the loading point from a supply placed at the operation by an electric mine locomotive. During loading the roof was supported by vertical wooden props paralleling the face. After the loading was completed the scraper engine and the ropes that had been used to propel the scoop in the loading of coal transferred the props to and along the face. A row of unfilled cogs was then built parallel to the new face and about 6 ft. from it. These cogs were usually made 6 by 3 ft., the longer dimension paralleling the face; they were placed on an average at 12-ft. centers. These wooden cogs were left in place and were buried later by falling roof. Attempts to remove them were never successful. When a new long face was started, the cog spacing would be increased to about 20-ft. centers. As successive cuts were made, weight would begin on the cogs, and they

Jan 1, 1939

By W. J. Rude

LARGEST of the known commercial deposits of pebble phosphate are those found in Polk County, Florida. The phosphate bed, commonly known as the matrix, will consistently average 6 to 9 ft. in depth, and is found under 3 to 60 ft. of over-burden. The phosphate pebbles, white and black in color, varying greatly in grade, are found imbedded in a matrix of sand and clay; and range in size from the fines to pebbles 1 1/2 in. in diameter, although the average coarse size is approximately 1/2 in. in diam¬eter. On some of the washers all material under 14 mesh is lost. High-grade phosphate (75 per cent plus of bone phosphate of lime, CasP2Oa) is generally soft, the pebbles breaking up during the mining operation and in pumping; low-grade phosphate, 67 to 69 B.P.L., is black in color with hard pebbles with no loss encountered in pumping.

Jan 1, 1941

By K. A. Gschneidner, O. D. McMasters, T. J. O’Keefe

X-ray diffraction, differential thermal, ad rnetallo-graphic methods were used to establish the Dy-Pb Phase diagram. Lead additions lower the 1377°C transformation temperature of dysprosium to 1360°C leading to an inverted peritectic reaction. The 327°C melting point of lead is lowered by dysprosium additions to about 326°C yielding a eutectic reaction. A second eutectic reaction occurs at 13.3 at. pct Pb and 1200°C. The dysprosium-richest intermetallic compound DysPb3 melts congruently at 1695°C and crystallizes in the hexagonal Mn5Si3 (D8,) type structure. The peritectic decomposition temperatures for the remaining compounds are Dy5Pb, at 1555C, DyPb2 at 955C, and DyPb3 at 880°C. A fifth compound near the DyPb stoichiometry exists over a 310°C temperature range decomposing at 1130°C by means of an inverted peritectic reaction and melting incongruently at 1440°C. The crystal structures of the compounds are discussed. A systematic study of the rare earth-lead alloy systems is underway in an effort to supply information concerning the alloying behavior of the rare earth metals. The Dy-Pb phase diagram is the fourth system to be investigated in this study. The Yb-Pb,1 Y-Pb,2 and Eu-Pb 3 diagrams have been published recently. Utilization of the rare earth series of metals as a research tool in this manner should yield a better understanding of alloy formation. EXPERIMENTAL PROCEDURE Materials. The lead used in this investigation was obtained from Cominco Products, Inc., and was specified to be 99.99 pct pure. The dysprosium was prepared in this Laboratory by the calcium reduction of the fluoride followed by distillation of the dysprosium. The major impurities in the dysprosium in ppm are: A1 (<40), Ca (400), Er (<50), Gd (<200), Ho (<200), Mg (<50), Si (30), Ta (400), Tb (<100), Y (<50), 0 (651, H (15), N (not detected), F (430), C (35). Alloy Preparation. Most of the alloys were prepared by melting weighed amounts of dysprosium and lead in sealed tantalum crucibles. The tantalum crucibles were sealed by are-welding in a He-Ar atmosphere welding chamber. Thus the alloys are in contact with He-Ar at about 1 atm pressure. Homogenization was achieved by holding them in the liquid state for about 1 hr, cooling, inverting the crucibles, remelting, and repeating the process at least twice. Since these alloys were prepared in sealed tantalum crucibles, chemical analysis for final composition was thought to be unnecessary. No detectable reaction of these alloys with the tantalum crucible was observed by metallographic examination. Metallographic evidence was also used to confirm the homogeneity of some of the alloys prepared in this manner. The compositions of a few alloys, which were prepared by nonconsum-able are-melting, were corrected for the small weight losses involved by assuming that the weight loss is due to vaporization of lead. The specimens obtained from the alloy samples were prepared under a dry-argon atmosphere because they were rapidly attacked by air and moisture. Thermal Analysis. Differential thermal analysis methods were used to determine the liquidus curves and reaction horizontals of the system. Both Pt vs Pt + 13 pct Rh and W + 5 pct Re vs W + 26 pct Re thermocouples were used to measure the temperature. An X- Y recorder was used to record the specimen temperature and differential electromotive force between the specimen and molybdenum standard. The arrest temperatures were measured potentiometri-cally. The accuracy limits (* values) associated with the reaction temperatures obtained by this method were estimated on the basis of both the reproducibility of the particular temperature value and the accuracy of the thermocouple at a given temperature. Liquidus temperatures were obtained from cooling arrest data while both heating and cooling arrest data were used to establish the horizontals of the diagram. Heat treatments during the thermal analyses of the alloys between 40 and 70 at. pct Pb were necessary in order to approach equilibrium conditions. The samples were held at temperatures between the various peritectic horizontals for l to 2 hr before the thermal analyses were continued. The entire range of compositions was investigated at the expense of a minimum amount of materials by adding appropriate amounts of lead to master alloys. More than sixty alloys were analyzed by this differential thermal method and for each alloy the results given herein are taken from two or three heating and cooling cycles. X-Ray and Metallographic Methods. Slice specimens for metallography and powder specimens for X-ray diffraction were prepared from rod-shaped samples which had been melted in sealed 0.62 5-cm-diam tantalum crucibles. The specimens were heat-treated in sealed tantalum crucibles which were protected by sealing them in argon-filled quartz ampules. Quenching was accomplished by breaking the ampules in ice water after heat treatment. X-ray powder specimens were sealed in 0.3-mm-diam glass capillaries under a dry-argon atmosphere. Copper, iron, and chromium radiation were used to obtain the powder patterns for these alloys. More than 150 powder patterns were obtained for specimens of various compositions and heat treatments. Included in these were several patterns for specimens which had purposely been oxidized. Patterns from specimens which had been accidentally exposed

Jan 1, 1969

By M. Hoch

Equations are derived from statistical considerations to represent the activities of each component of an interstitial solution, and of a compound with a wide homogeneity range as a function of composition and temperature, based on the interaction energies between the various components, Eij. The equations are checked on the binary systems Fe-C, Ta-H, and Y-H, the ternary systems Ti-O-H, liquid Fe-C-0, and the compounds TiO, MnO, COO, and YH,. In all cases the present model represents the experimental data well. THE aim of this paper is to derive from statistical considerations the thermodynamic behavior of non-substitutional solid solutions. "Nonsubstitutional solid solution" means either an interstitial solid solution (carbon in iron, oxygen and hydrogen in hexagonal and bcc titanium, and so forth) or deviation from stoichiornetry in compounds (introduction of vacancies—removal of atoms in one or both lattice sites of compounds FeO, MnO, TiO, NbO, YH2). wagnerl and Fowler and Guggenheim considered the theory of compounds with small deviation from stoichiometry; Anderson includes larger deviations from stoichiometry, the defect being present in one component only, as vacancy and interstitial. Rees considers only vacancies in one of the components and introduces various kinds of sites for the component where the defect occurs; the various sites interact with different energies, thus giving isotherms with two or more plateaus. Both Rees and Anderson are mainly occupied in determining the limits of two-phase regions, and the defect interaction energy is determined from the critical point. Darken and Gurry5 gave a brief treatment of carbon solution in iron; Speiser and spretnak calculated the configurational entropy for binary interstitial solid solutions by assuming that each interstitial atom in the solution excludes a certain number of neighboring interstitial sites from occupancy. Use will be made of this concept later. Hoch et al treated transition metal oxides of the NaCl-type structure, and also oxygen solution in titanium.&apos; The main aim was to determine the behavior of the activity of one of the components as a function of the composition in the single-phase region. In the present paper, the various interaction energies are discussed in detail and the similarity between interstitial solid solutions and deviation from stoichiometry in ionic compounds is shown. Both types of systems have in common that at least on one kind of lattice site only one kind of atom occurs; this gives a fixed frame to the system, permitting a much easier statistical treatment than for the substitu-tional solid solutions. (The theory is also applied to ternary systems.) The difference between an interstitial solution and deviation from stoichiometry can be explained as follows. In an interstitial solution in the pure or standard state the host atom or host structure is present alone and all the interstitial sites which are going to be filled when the interstitial atom is introduced are empty. The interstitial solution is now created by introducing atoms into this empty lattice. In the deviation from stoichiometry, both kinds of lattice sites are already occupied in a special fashion (all lattice sites occupied, or the same fraction of lattice sites empty, or one kind completely filled, the other only two-thirds). Deviation from stoichiometry removes atoms from lattice sites, adds them, or removes atoms from one kind of lattice site and introduces them on the other lattice site. Though both cases (interstitial solution and deviation from stoichiometry) lead almost to the same equations, they are treated separately. The treatment given below corresponds to the "regular solution"10 treatment of substitutional solid solutions. Speiser and spretnak&apos;s6 treatment is similar to the athermal solution in the substitutional use. a) INTERSTITIAL SOLID SOLUTIONS Theory. It will be assumed that there are N lat-tice sites occupied by the host atom (denoted by 1). Corresponding to those N lattice sites there are N octahedral and EN tetrahedral interstitial sites. If only one kind of interstitial atom is added, this in-

Jan 1, 1964

By L. H. JEFFRIES

In the mining operations of The Canyon Corp., Deadwood. S. D., the use of mucking machines has been of definite advantage. The type used is that which depends upon the traction of the motor-driven wheels to crowd the dipper into the muck pile, while the car in which the muck is received is coupled to the mucker and moves forward or back with it. This general arrangement is entirely satisfactory on a substantially level track. The ores which occur in this district are a replacement of dolomite and the beds are now tilted to an inclination of about 7-1/20. In our operations it is necessary to drive inclines down-hill on this slope, which makes a difficult hand-mucking job even if water were not present. With these facts in mind, an attempt was made to use the mucking machine for driving down the in- cline, but as expected, the traction was insufficient to handle the machine and the necessary car. The means used to correct this condition will perhaps impress most readers as too complicated and cumbersome to effect any economy, but the idea may be of service to some who have a similar condition. After considering several s

Jan 1, 1940

The nickel suppliers are hard at work across the entire spectrum of the industry-from exploration and mining on the one hand to the development of new applications of this unique metal on the other. The reason-a surging demand for nickel by the free world. Evidence of interest and activity in nickel abounds. Companies such as Anaconda, American Metal Climax, Kaiser Aluminum & Chemical, Patino, Newmont-firms that have not been in the nickel industry before-are now involved in various exploration and development ventures around the world. International Nickel, Falconbridge, Le Nickel and Sherritt Gordon-the big names in the industry -have committed vast sums of money and talent in a variety of new developments designed to ensure their status as leading producers of this commodity. As a result, the world is now seeing a rapid build- up in nickel capacity, and in this issue of [ ], the editors have prepared a summary of these fast- moving major developments.

Jan 10, 1968

By W. Randolph Van Lewis

In determilling the relative rate and in fi~lding the point where different inlpurities containecl in copper-matte are eliminated during the process of a converter-blow, the follo~ving results were obtainecl : A converter was selected which was starting on its sccolld charge. The first charge after lining had finished its copper " hot," and conseqaently no copper was adhering to the sides of the lining. All the copper and granulated slag from the previous charpc mcrc dumped, thus removing ally possibility of " salting " the matte to be tested. The coliverter worked fast and well during the entire test. Periods of ten minutes were selected. The converter mas brought from the stack to secure each sanlple of matte to be

Jan 1, 1904

By R. W. Raymond

The death of Privy Councilor Bruno Kerl, on March 25, 1905, terminated a distinguished and useful career. Bruno Kerl was born March 24, 1824, at St. Andreasberg in the Harz, and entered in 1840 the mining school of Claus-thal, where he studied for three years, working at the same time in the mines and stamp-mills. After an additional year of practice in the silver-reduction and iron-works of the Upper Harz, he passed his examination as a metallurgical graduate, and studied for a gear at Göttingen under Wöhler in chemistry, Hausmann in mineralogy, and eminent teachers in other branches. In 1846 he was employed at the Oker works, but very soon left this post, to become a tutor in chemistry, metallurgy, etc., at Clausthal, where he continued to labor until 1867. During this period the Clausthal school became a completely equipped Mining Academy, and Kerl was made in 1862 a full professor. Meanwhile, in addition to the work of instruction, he discharged, simultaneously or successively, the duties of many responsible official positions in the Royal Hanoverian administra-

Jan 1, 1906

Frank Firmstone was born Aug. 29, 1846, at Glendon Iron Works, near Easton, Pa., the residence of his father, William Firmstone, one of the pioneers of the anthracite-iron business. After preliminary school education at Easton, Pa., he attended the Saunders Military Academy in Philadelphia and subsequently entered the Polytechnic College of Pennsylvania, where he was graduated as Mining Engineer in 1865, at the age of nineteen. In 1865 and 1866, he was employed in railroad surveying. In January, 1867, he became draftsman and in 1869, assistant manager of the Glendon Iron Works, of which his father was manager until his death in 1875, when the son practically succeeded to that position, becoming formally in January, 1877, and remaining until February, 1887, the manager of the works and business agent of the Glendon Iron Company. In February, 1889, he became President of the Cranberry Iron and Coal Company, and held that position until November, 1897. He was a director of the Longdale Iron Company, Longdale, Va., from its organizationin 1870 until its dissolution in 1911. With the termination of this official responsibility, Mr. Firmstone retired from active business, although he continued to maintain an intelligent interest, and to play a helpful part, in the scientific progress of the iron industry, in which he had been a leader.

Jan 1, 1920

Jan 1, 1899

New York, March 18, 1913. MR. CHARLES F. RA ND, President, New YORK, MARCH American Institute of Mining Engineers. Dear Sir: In connection with the official notice of Dr. Raymond&apos;s unanimous election by the Directors as Secretary Emeritus, we wish to place upon record certain statements concerning his services to the Institute which we think have not been published., and may not be generally known to the majority of our fellow-members. When the Institute was formed in 1871, Dr. Raymond acted as Secretary of the Founders&apos; Meeting, and became the first Vice-President of the Institute, and, by request of the aged and beloved David Thomas, who was the first President of the Institute, Dr. Raymond discharged all the duties of the office of President, to which he was later formally elected in 1872, and which lip held for three years. During that time, he visited Europe, and through his acquaintance and reputation abroad, established those international relations of the Institute which proved so important in later years. He also enlisted the support of the mining engineers and metallurgists of the Pacific Slope, who would not otherwise have been disposed to join a society originating in the East. And for twelve years he attended; at his own expense, nearly every meeting of the Institute, wherever held, giving to it without remuneration his best service, and sacrificing for it many professional and private interests.

Jan 4, 1913