Search Documents

By M. van Swaay, C. E. Birchenall

Palladium has a large capacity for the dissolution or occlusion of hydrogen; the gas also diffuses very rapidly through the metal. Palladium thimbles are widely used in the laboratory for purification of hydrogen by diffusion. The use of palladium filters could be extended to several large-scale applications if greater stability of the permeation process could be attained. In this paper a number of aspects contributing toward this goal are discussed, and new data on solubility and diffusivity are given. Palladium sheets of 0.005, 0.010, or 0.020 in. thickness were prepared by three procedures: casting and rolling, sintering palladium powder, and sintering palladium powder to which 0.1 pct thorium oxide had been added. Half-inch diam circular specimens were cut and clamped in a stainless steel holder provided with knife edges to seal the palladium sheet with soft copper gaskets. The seals were tested for leaks at l0-5 mm Hg. No difficulties from this source were encountered even after many temperature cycles in the system. The holder was silver-soldered to Kovar-glass seals and attached to the system through glass ball joints. Each joint was sealed with Apiezon wax and was adjacent to a cold trap. In several experiments the holders were fused directly into the system, eliminating the ball joints, to show that the wax did not affect the filter. Three filter holders were supported in holes in a stainless steel cylinder, which also acted as a temperature equalizing block inside the resistance wound furnace. The measuring thermocouple was inserted in one of the holders. A potentiometric controller with control thermocouple on the furnace heater winding maintained ± 0.2oC. Electrolytic hydrogen was purified and stored as shown in the flow diagram, Fig. 1. It could be admitted to either or both sides of the palladium specimens. Only a mechanical pump was used, for even high pumping speeds would not bring the pressure on the off-gas side of the filter below 10 to 50p Hg owing to the rapid hydrogen flow through the filters. A series of steady-state permeability studies allowed identification of several conditions of permeability loss. A constant fore pressure was maintained while the low-pressure face was pumped. After enough time had elapsed for a steady flow to be established the pump was cut off, and the rate of pressure increase in a thermostated bulb was measured to determine the flow rate. The time delay method of Daynes1,9 was adopted since it offered the possibility of determining solubilities and diffusivities. For each measurement both sides of the filter were evacuated for 15 min, which gave about 10-4mm Hg residual pressure. Hydrogen was admitted to one side or the other of the filter at a fixed pressure. The pressure on the off-gas side was observed as a function of time. A

Jan 1, 1961

Jan 1, 1969

By Samuel B. Christy

Jan 1, 1889

An Appreciation of Dr. Douglas by Dr. ALBERT R. LEDOUX The Bulletins of the American Institute of Mining Engineers and the program of the International Engineering Congress, held last September at San Francisco, called attention to an important feature in the pro¬ceedings of the Congress; viz., the public presentation to Dr. James Douglas of the John Fritz Medal, for notable achievements in mining, metallurgy, education. and industrial welfare. Dr. Douglas' health, unfortunately, did not permit of his taking the journey to California. While he had been willing that the bestowal of the medal should be a public ceremony, his natural modesty made him shrink somewhat from what he considered something of an ordeal, and he begged those who were to take part in it to use restraint in anything which they might have to say as to his work and attainments. It was, therefore, with some considerable satisfaction on his side that he learned that the medal would be given him without a public, ceremony in New York, or elsewhere. . On Dec. 5, 1915, the writer of this had the pleasure of handing him the medal, certificate, and official letters of transmittal, at his home at Spuyten Duyvil, where lie was surrounded by his children and grandchildren, with one or two of his most intimate friends. He begged the writer to return his thanks to the Committee of Award; and again to express the feeling that nothing in his career merited so great an honor. On this point all of the members of the Institute will share the writer's feeling that Dr. Douglas is too modest. James Douglas was born at Quebec, Canada, in November, 1837. His father Was a distinguished physician and surgeon, employing his skill in the field of philanthropy: He established the first retreat for the insane in the Dominion, to which lie. devoted himself up to the time of his departure from Canada, when it was taken over by the Government. The son spent 2 years in study at the University of Edinburgh, which lie entered in 1855. Returning to Canada, he graduated from Queens University, at Kingston, Ontario, with the degree of Bachelor of Arts, having also studied medicine, and later theology. After his graduation he traveled extensively with his father in Europe and in the Orient, visiting Egypt several time's. They returned with important archaelogical collections, which Dr. Douglas subsequently donated to the Metropolitan Museum of Art in this city. He then returned to Edinburgh, where he continued his course in medicine, surgery being perhaps his chief interest at that time. He was subsequently licensed to preach and his contemporaries bore testimony to his broad philanthropy and to the sympathy which dominated his every act. His taste was distinctly literary; he had carried off a prize at Edinburgh in English literature.

Jan 1, 1916

By R. F. Mehl

Jan 1, 1936

By Benjamin F. Tillson

The hammer drill rightly receives the credit for having made the one-man drill possible, and so many economies seem possible through the proper application of different types of hammer drills to various mining, quarrying, and excavating operations, that an indication of the 'economies effected by the New Jersey Zinc Co. at its Franklin mines may be of pertinent interest. When this company commenced its trials of hammer drills in 1907, these tools had not been developed to one-fourth the capacity and refinement which they have at present. At that time it was frequently stated that such a small tool, drilling holes of less diameter than the reciprocating rock drill, could not drill enough holes in a shift to permit the placing of sufficient explosive to break a tonnage of ore comparable with that produced by the "rock drills;" that the placing of small holes inclined upward, at angles steeper than 40' above the horizontal, could not be expected to produce results equal to the large flat, wet or dry, holes in the breasted back of an overhand stope, and would only shatter the ground so as to make the back unsafe. In spite of these adverse opinions, the hammer drills first showed their superiority over both heavy and light reciprocating drills in raising and in stoping, and then in drifting and quarry work. As a result, all of the reciprocating drills at the Franklin mines were scrapped three years ago, all of the mining work being accomplished with increased efficiency, as shown in detail in this article. With the advent of the hammer drill in this property, it was considered advisable to make comparative tests of all the tools accessible, and it has since been the policy to investigate the merits of any advance of the drilling art in order to get the maximum amount of work from the tools. The necessity of devising some means of standardizing drill tests, and of measuring the consumption of compressed air as well as the drilling speed, was early realized. The common test was to fill a measured air receiver with compressed air at a certain gauge pressure, run the drill until the pressure had dropped to too low a figure, then compute from the time, drop in pressure, and

Jan 1, 1915

By O. P. Chisholm

Dross emerges from the blast furnace either with the lead through a lead well or by tapping from a forehearth or settler, but until a dozen years or so ago few dross reverberatories were used in western lead smelters because it was the usual procedure to circulate the dross from the drossing lead kettles back to the blast furnace. It was quite customary for lead smelters to produce matte in their blast furnaces, as this was the form in which copper could be collected, concentrated if necessary, and shipped to the copper smelters for further treatment. The main prerequisites for good matte formation arc., of course, a more or less definite amount of copper on the charge and sufficient sulphur. Such troublesome impurities as arsenic and antimony were ignored, in so far as possible, although they contaminated the bullion and thereby increased refinery costs. At the same time stocks of blastfurnace speiss containing gold, silver, lead and copper in addition to iron, arsenic and antimony, were being accumulated for want of a market to absorb them. As the dross was being fed back to the furnaces as rapidly as it was being produced, arsenic and antimony tended to build up until the arsenic could effect a combination with copper and iron and an alliance with lead, and the antimony a combination with copper and an alliancc with lead. Sulphur, being the most active agent in taking up the copper, left little of that element for the arsenic and antimony, so that on the whole a somewhat unsatisfactory metallurgy resulted. During this same period, certain lead plants were beginning to encounter trouble with zinc due to the replacement of crude ores of lot zinc content by concentrates containing high percentages of lead and zinc in sulphide form, the blast-furnace slags resulting from the smelting of such concentrates being characterized by a decidedly increased zinc content. It was soon realized that zinc plus sulphur was "poison" to a lead blast furnace and steps were taken to reduce the sulphur content,. At this stage some plants found that any substantial matte fall was out.

Jan 1, 1937

The General Committee met in the Treasury Building at Washington on Oct. 6 and 7. At the first meeting, Cornelius P. Kelley was appointed chairman, and Paul Armitage, secretary. Sub-committees were ap-pointed on Invested Capital, Mine Valuation, and Depletion and De-preciation. On Oct. 7, the reports of these committees were submitted to the General Committee and were referred to the Executive Committee. A motion was carried that the Executive Committee he constituted a permanent committee to continue the work of the Committee, with full power to acid to and increase its membership, that. as thus increased, it should constitute a permanent organization to act- and cooperate with the Treasury Department in matters of mining taxation under the Federal Income and Excess Profits Tax Laws. Thereafter the Executive Com-mittee met and formed a permanent committee as follows: Cornelius F. Kelley, chairman, 42 Broadway, New York City. J. L. Darnell, office of the Commissioner of Internal Revenue, Wash-ington, D. C. J. Parke Channing, 61 Broadway, New York City. Walter Douglas, 99 John St., New York City. R. V. Norris, 542 Second National Bank Bldg., Wilkes-Barre, Pa. J. E. Spurr, Engineering and Mining Journal, 10th Ave., and 36th St., New York City. W. G. Swart, 808 Selwood Bldg., Duluth, Minn. J. P. Finley, 45 Cedar St., New York City. W. A. Williams, Bartlesville, Okla. F. S. Peabody, Peabody Coal Co., McCormick Bldg., Chicago, Ill. Matthew C. Fleming, 71 Broadway, New York City. H. B. Fernald, 54 Wall St., New York City. William G. Mather, Cleveland, Ohio. Walter Fitch, Eureka, Utah. Arthur Thacher, 900 Security Bldg., St. Louis, Mo. John P. Gray, Coeur d'Alene, Idaho. Paul Armitage, secretary, 233 Broadway, New York City.

Jan 12, 1919

By J. Richard Kyle

Lead-zinc ore bodies in the upper part of the Pine Point carbonate barrier complex are localized in paled-solution structures that developed as the result of post-middle Givetian subaerial exposure. Detritus-filled dolines host prismatic ore bodies, and macropores and stratabound permeable zones contain tabular ore bodies. Sulfides are concentrated in these transgressive paleosolution structures that acted as natural bypasses between aquifers and loci for mixing of fluids of different character. Complex ore textures indicate rapid early sulfide precipitation followed by slower sulfide growth. Evidence for both sulfide-carbonate equilibrium and disequilibrium conditions suggest fluctuations in ore fluid composition, perhaps related to periodic supply of reduced sulfur. District and ore body metal distribution pattern may reflect the nature and movement of mineralizing fluids.

Jan 1, 1981

By J. C. Febles

HISTORY. THE use of iron for the precipitation of copper was known at least as early as the fifteenth century. Both Paracelsus and Basil Valentine refer to it in their writings, as early as 1500 A. D. It was used in Peru, for this purpose prior to 1637, and at Rio Tinto, Spain, as early as the sixteenth century. The statement has been made repeatedly that in the early history of the mining industry at Butte, the practicability of this method of recovering copper from solution was overlooked, and that enormous quantities of copper-bearing water were allowed to go to waste, the copper in which might easily have been recovered at small cost; and that this oversight on the part of the mine operators was due to ignorance of this method of recovering copper. As a matter of fact, very little copper-bearing mineral was encountered in the mines of Butte until a depth of 400 or 500 ft. bad been reached, and in many cases much greater depths were necessary to reach the copper-bearing zone. The water encountered in the upper levels (although in most cases quite highly mineralized) contained little or no copper, and it was only after considerable areas of copper-bearing ore had been uncovered and developed that copper sulphate began to. appear in the mine water in any considerable quantity. In fact, the first water that was observed to contain copper carried it in such small amounts as to be of little or no importance. It was only after years of underground work had opened extensive areas of stopes, drifts, and other underground workings, these being subsequently filled with waste, nearly all of which contained small copper values, which became oxidized by exposure to the air and were acted upon by the slowly percolating mineral water, that the recovery of copper from mine water became commercially important.

Jan 7, 1913

Following closely Marcona Corp.'s announcement of its new Marconaflo process for transporting mineral slurries by ship (see pp. 96-97, Sept. 1969 [ ]), Midland-Ross Corp. (M-R) now heralds its metallized iron pellet process which supplements Oregon Steel Mills1 (Oregon Steel) new Portland, Ore., plant. Harry J. Bolwell, president of M-R describes the company's M-R Pellet as "the most exciting advance in steelmaking in a decade, one which will profoundly affect the industry." In fact, other knowledgeable industry spokesmen believe that with these developments the mini-steel plant era is now here and that this technical development along with the Marconaflo process will revolutionize iron ore shipments and steelmaking. The M-R president predicts that electric furnaces can account for 20% of the annual U.S. steel production by 1975, compared with 14% at the present time because of these developments.

Jan 12, 1969

By A. U. Seybolt, J. L. Walter

The effects of the addition of 0.5 pct ThO2 (by volume) on the grain structure and texture of heavily rolled tungsten sheet were studied. Powder metallurgy ingots were rolled to sheet, 0.001 in. thick, and samples were annealed at temperatures from 1200" to 2500°C. The heating rate to the anneal temperature was varied from 3°C per min to 6500°C per min. The orientations of the largest grains were determined by X-ray diffraction. The disposition and loss of the ThO2 particles were determined by electron transmission microscopy and the activation energy for remozlal of the thorium was measured by mass spec-troscopy. Heating rates below about 800 C per min produced large, highly elongated grains. Higher heating rates produced much smaller, less elongated grains. The grain structure and texture of the slowly heated samples were identical to the structures and textures of heavily rolled tungsten foil conventionally doped with aluminum, silicon, and potassium but the recrystallization temperature was about 200°C lower. There was stringer-like dispersion of larger ThO2, particles superimposed on a uniform dispersion of fine particles. The particles increased in size and decreased in number with time at temperature. The loss of particles was accompanied by formation of grain boundary voids and surface pits. The activation energy for removal of the ThO2 was about 40 kcal per mole. THE addition of small amounts of aluminum, silicon, and potassium to tungsten has a profound effect on the grain structure of heavily rolled sheet1 or drawn wire."4 Thus, "doped" tungsten sheet, rolled to 0.001 in. and recrystallized, develops a structure consisting of large, highly elongated grains of a specific preferred orientation.' It has been shown that the elongated grain structure was caused by a dispersion of particles, identified as mullite (Al6si2O13),1,4 in strings parallel to the rolling direction in sheet or to the wire axis. Identical results were obtained for iron which was doped with glass and rolled to 99 pct reduction of thickness and recrystallized.5 Again, the glass particles were disposed in strings parallel to the rolling direction. The strings retarded boundary migration in the lateral direction but grain growth was able to proceed relatively unhindered along the direction parallel to the strings.1,5 In both the doped tungsten and the glass-doped iron, the particles were highly plastic during the high-temperature deformation. Since mullite melts at about 1800°C and the glass employed melts at about 810ºC, the particles were probably molten during the recrystallization anneals (above 1800°C for the doped tungsten and 850°C for the glass-doped iron). There are indications in the literature that particles not plastic at hot-working temperatures (up to about 1550°C for tungsten) may also impart elongated grain structures by primary recrystallization of worked alloys. Examples are dispersions of tantalum carbide in chromium,6 and ThO2 in nickel where elongation ratios of recrystallization grains of up to 20:l were obtained.7 Strings of ThO2 particles in W-ThO2 wire have been seen by Rieck.8 In view of the available evidence, it was of interest to extend the previous studies of doped tungsten and glass-doped iron to include W-ThO2 sheet materials. Of specific interest was the grain structure, preferred orientation, recrystallization temperature, and disposition of the thoria particles. EXPERIMENTAL PROCEDURE A) Material Preparation. About 380 g of blue tungsten oxide (approximate composition WO3) was wet with a sufficient amount of aqueous solution of Th(N03)4 to provide 0.5 vol pct ThO2. The wet mixture was stirred to distribute the doping material uniformly throughout the powder. Stirring was continued while the mixture was heated until it was completely dry. The dried, doped mixture was then reduced to tungsten powder by heating at 850°C for 2 hr in a stream of dry hydrogen. The doped tungsten powder was hydropressed in a rubber sack at pressures of 50,000 psi to produce an ingot approximately 2 cm diam by about 5 cm long. Next, the pressed cylinder was heated in hydrogen for 2 hr at 1350°C to render it strong enough for machining. The cylinder was machined to a square cross section of 1.6 by 1.6 cm with rounded corners. Finally, the bar was heated for 2 hr at 2150°C in hydrogen to provide a sufficiently dense mate rial to withstand the hot-rolling operation. Prior to rolling, the ingot was reduced in thickness by about 20 pct by forging at 1550°C. This served to increase the density of the material and to widen it slightly for better rolling characteristics. The forged ingot was then rolled at 1550°C to a reduction of 45 pct of thickness, following which the rolling temperature was reduced to 1300°C and the slab rolled, with several reheats, to 0.050 in. Further reduction was accomplished at 800°C in tungsten sheet packs to a total reduction of about 99.85 pct. B) Annealing Treatment and Observation of Structure. Small samples of the rolled foil were annealed in one of two ways. Some of the samples were suspended in a covered tungsten can and annealed at temperatures from 1200" to 2200°C for various times in vacuum of l0-7 to 10-6 mm Hg. The can was heated by induction and temperatures were determined by optical pyrometry

Jan 1, 1970

By Carl R. Christiansen, James J. Scott

Advance mine planning, coupled with good mining practice, can be employed to develop underground space in stone mines for future industrial usage. To assure the developer the maximum return on his investment, initial planning should consider all aspects of the commercial operation, including surface layout, mining, and underground industrialization. The modular concept of mining to compartmentalize the space offers several advantages over conventional methods. Some expenditures can be considered as mining costs with a reduction of profit from stone production while lowering the capital requirements for conversion for usable space.

Jan 1, 1977

By Edwin B. Johnson

The success of self-fluxed sinter in enhancing the operation of the blast furnace during the past few years has reasonably led to the assumption that the use of self-fluxed pellets might result in even greater furnace efficiencies. A great share of development work in agglomeration has been directed towards techniques related to the production of self-fluxed pellets, but no appreciable tonnage of self-fluxed pellets had been produced on a commercial scale until this past year when The Cleveland-Cliffs Iron Co. produced 35,000 tons of such pellets by the grate kiln system at the Republic mine during the period May 21-June 5, 1962.

Jan 3, 1963

Domestic: Middle West-,11.. B. Newcombe Eastern District-J. French Robinson1 Kansas-Henry A. Ley 2 Oklahoma-Henry A. Ley 3 Texas, except Gulf Coast and Panhandle-M. G. Cheney 5 Texas Panhandle-W. E. Hubbard and H. E. Crum 6 Gulf Coast-L. P. Teas 7 South Arkansas, North Louisiana and Mississippi-H. K. Shearer 8 Foreign Mexico-V. R. Garfias and C. 0. Isakson 9 Canada-Line M. Farish 10 Venezuela-C. W. Hamilton 10 Colombia-J. T. Duce 12 Peru-O. B. Hopkins 12 Trindad-Williaim J. Millard 13 Dutch East Indies-Fred B. Ely 13 Rumania-I. I. Gardescu . .. . 14 India-Eric J. Bradshaw 14

Jan 1, 1931

By R. Hadfield

Last year this institute was good enough to accept some remarks by the writer regarding sound steel, entitle Plant for Hadfield Method of Producing Sound Steel Ingots…

Jan 1, 1915

By V. E. Christensen

AT most smelting plants, forced draft, induced by high stacks or fans, is used to carry the gases away from the furnaces, roasters, or sintering plants. Gases moving under forced draft carry varying amounts of solids in the form of dust and fume. Where the weight of the solids is material, and the metal content high, it is usually profitable to treat the gases to recover these solids. Baghouses, Cottrell treaters, and settling chambers are the common forms of plants used to recover solids from gases. To check on the efficiency of these plants it is necessary to know the volume of gas leaving the plant and the amount of solids carried by the gas. As the volume of gas is equal to the product of the velocity of that gas and the cross-sectional area of the flue, the determination of the volume includes the measurement of the area of the cross section and the determination of the velocity. The velocity is generally measured by means of the Pitot tube and Ellison differential pressure gage, although low velocities are best determined by means of an anemometer. The dust concentration is determined by passing a measured volume of sample through a filter and weighing the dust caught. From this the dust concentration per unit of volume may be calculated. It is necessary to assume that the gas is homogeneous or that each cubic foot of the gas contains the same weight of dust as every other cubic foot. Having the volume of gas passing through a flue per unit of time, and the dust concentration of the gas per unit of volume, the amount of solids may easily be calculated.

Jan 1, 1935

By A. B. Parsons

AT the outset, the authors of this paper desire to file a disclaimer and an, explanation. They have no inside information from occult sources; neither of them feigns clairvoyant powers in the slightest degree. It is true that they have indicated on be graphs an approximate trend for the consumption of seven important mineral commodities up to the year 1954. At best this is a risky business; the figures do not pretend to be any- thing more than reasoned conjectures that are predicated on an attempt to evaluate some of the more obvious of the many factors that are likely to have a bearing on the future.

Jan 1, 1937

By E. H. Tenney

A discussion of the probable future use of coal for power development involves the study of several basic factors, such as future demand for power, the quantity and availability of fuels in direct competition with coal, the price of coal, and a closely related factor—the efficiency and cost of fuel utilization. Predictions based on purely statistical analyses of past coal consumption have definite limitations. For example, statistics showing the relation between coal utilization and total energy consumption from all sources between the years 1890 to 1930 indicate that during that period the energy consumption per person in the United States increased five times, while the coal consumption per person increased only twice1, and there has been an actual decrease in per capita coal consumption since 1920. Figures such as these, compiled by authentic agencies, emphasize the need for caution in attempting estimates as to the future use of coal, and, incidentally, would seem to offer little basis for optimism in the coal industry. They also suggest the value of analyzing broadly the part played in the past by the related factors of power consumption, competitive fuels, coal prices and the efficiency of utilization. Proper weight must also be given in such a study to the present status and limitations of power-plant developments, arid to the question of what the coal industry itself can do to further its own interests arid influence the consumption of its product.

Jan 1, 1936

By D. A. J. Swinkels

The problem of determining oxygen levels in liquid steel to aid in deoxidation control has received general attention for a number of years. Work in this direction started at the B.H.P. Central Research Laboratories early in 1967 with an evaluation of sampling techniques followed by vacuum fusion analysis to determine the oxygen content of the samples (1). It was found that these techniques had a number of drawbacks if they were to be used for deoxidation control. The method of analysis was rather too slow to allow effective control and measured total oxygen level rather than dissolved oxygen. Furthermore, the results were found to be very variable due to slag entrainment in the samples. Attention therefore turned to the galvanic cell method using a solid oxygen ion conductive electrolyte such as cubic stabilised zirconia. The ionic conductivity properties of electrolytes such as (ZrO2) 85 (CaO).15 had been studied by a number of investigators and had already been applied to the measurement of oxygen activity in gases, in lower melting metals such as copper, lead, tin, silver, alkali metals and indeed the first studies in steel had been made (2,3). Since then the results of a number of studies in the development of an expendable oxygen probe for steel have been reported (4-9).

Jan 1, 1972