Search Documents

By B. J. Shaw, R. Kossowsky, W. C. Johnston

High purity (99,95) Ni-51 wt pct cr eutectic alloy was unidirectionalty solidified at rates of 0.1 to 8 in. per hr. The resulting material was characterized by large grains, approximately 0.5 mm in cross section and extending through almost the entire length of the specimen, parallel to the growth axis. The eutectic structure of specimens the growth at -1/3 The per hr consisted of a continuous nickel-rich phase and chrome -rich lamellae approximately 2 thick, spaced about apart. Specimens were tested in compression at temperatures ranging from —196 to 850"C over which range the 0.2 pet yield strength dp -creased from 160,000 p si to 35,000psi, respectively. Swaging to 40 pet reduction in area, followed by a 30-min anneal at 1000c to remove residual cold work, increased the 0.2 pet yield to 260,000 psi at -196°C, dropping to 35,000 psi at 850°C. The increase in strength was attributed to a residual cell structure. The strength of the alloy could be rationalized by the simple rule of mixtures if one assumed that additional strength is derived front a size effect characterized by is petch equation IN recent years there has been increasing interest in dispersion and second phase strengthening in materials needed for high-temperature applications. inm role of structure on the mechanical The of such alloys has been well established of such some extent accounted for theoretically. and to of how the strengthening mechanisms due to fibers and lamellae operate has been reduced to its fibers form by the fabrication of composites of strong rods unidirectionally aligned in a From work on tungsten-fiber-reinforced copper, for example, it was established that the "Rule of Mixtures" could explain the strengthening.12 " some what more sophisticated technique for introducing strong fibers into copper matrix was used by Hertzberg strong Kraft3 who unidirectionally solidified the copper-chromium eutectic. The use of unidirectionally fied eutectics has advantages in that there are no matrix-fiber wetting problems and fine fibers are automatically aligned and uniformly fiber However, one Is restricted to a specific volume fraction of the second phase. Nevertheless, even though the volume fraction is fixed, the rod or lamella thickness, , can be varied by controlling the freezing interface velocity. Alternatively, the grown material may be worked down by swaging or rolling. Embury and Fisher, " using this approach, drew down pear lite in iron and studied the mechanical properties iron and that the yield strength, oy, was properties.proportional They that d was the wire diameter. It could be inferred that was also proportional to but the work hardening had to be taken into consideration at the same time. By varying the growth rate of the cadmium-zinc lamellar eutectic, Shaw'1 showed that was proportional to without the introduction of work hardening and suggested that the lamellar interface itself contributed to the strengthening of the composite. In this investigation we have evaluated the mechanical properties of the unidirectionally solidified fec-bec eutectic Ni-Cr. This eutectic was selected because it presented the possibility was selected beca temperature, and high corrosion resistant alloy, and also represented a hard-soft phase combination with two completely different slip systems. Specimens were tested in compression and tension up to 850°C and a detailed study of the micro structure as a function of plastic strain and temperature was carried out by light and electron microscopy. It was shown that the composite strength tested in compression can be accounted for by the simple rule of mixtures if one allows for an additional term representing the effect of Intereprese EXPERIMENTAL PROCEDURE 1) Unidirectional Solidification. Fig. 1 is a schematic drawing of the apparatus used to produce 0.2 in. diam by 12 in. long alloy ingots. The crucible tube is alumina, containing the charge which has been is swaged, or machined to 0.195 in. diam. The lower end of the tube is immersed to 0 .195in in.d iam. The upper end is supported by a 10 mil nichrome wire which lowers the crucible mil nic hr the] wire at a prescribed rate. Surrounding the furnace is a graphite susceptor into which a control thermocouple is inserted. The furnace is insulated with fiberfrax and enclosed in a quartz tube. There is a sliding seal at the bottom around the crucible and one on the top so that an atmosphere may be used for the sample and suscep tor. The power for the furnace is supplied from a 10-kw, 450 kc generator. The skin depth (the skin depth at which the field falls to l/e of its value at the outer surface) for graphite (p = 10 (j-ohm-cm) is 0.1 in. at this fre-

Jan 1, 1970

By S. R. Gilbert, B. W. Burdett, L. B. Hales

A brief review of grinding control systems is given with a review of the most popularly reported control loops. The trend toward more sophisticated control systems in terms of control strategies and control equipment is discussed, and the reasons for the popularity of distributed control equipment are outlined. The evolution of the interface between the operator and the process and its importance in plant control is described. Finally, the authors' view is given as to the future of grinding control.

Jan 1, 1984

By Richard P. Rothwell

The anthracite coals of Pennsylvania are all mined from large veins. A seam less than four feet. in thickness is generally considered as unworkable, those from which most of the coal now comes being from 8 'to 30 feet thick. The system of mining employed is, almost without exception, that known as " chamber and pillar work;" that is, the coal is taken out of chambers of from 18 to 30 feet in width, and pillars of from 12 to 20 feet are left between these to support the roof. In general, the entire thickness of the seam, even

By John S. Johnson

THE purpose of this article is to describe several types of borehole lining in common use, and especially to offer a relatively new means of reducing the expense of maintaining boreholes where they are subjected to corrosive action of water flowing either inside or outside of their casing. In the Anthracite region of Pennsylvania, boreholes are used for many purposes, the principal ones being: openings between the surface and underground workings through which are passed steam, water and compressed-air lines, ropeways from surface hoists to underground rope haulages, conduits for electric power and signal lines, water-discharge lines from underground pumping stations, and inlets to mine workings for flushing material. LININGS FOR BOREHOLES The inadequacy of steel pipe for use in boreholes has long been recognized. Various substitute materials have been tried, including screw-joint cast-iron pipe (Fig. I). Cast-iron pipe, while very effective as a discharge line for acid water (mine water) being pumped to the surface, is not so effective when serving as a conduit for silt and crushed rock being flushed underground for filling mine voids. Terra cotta pipe (Fig. 2) has been used in boreholes, and lasts a long time if the glazed inner surface of the pipe remains intact. Its installation in a borehole is very difficult and is recommended only where it is certain that there will be no subsidence of the surrounding territory. Accessibility in order properly to join each section of the pipe is essential to a satisfactory job. In large water holes, where it is possible to lower a man into the hole for sealing the joints of the pipe, glazed terra cotta pipe has been used successfully for delivering mine water from pumps in the mines. For large holes used for flushing refuse into mine workings where the surface wash is shallow, standard paving brick have been used to form a tube through the wash to the bedrock. These brick are laid radially, backed by common brick and cobbles laid in cement. It is obvious that the shaft through the wash must be large enough to permit a man to work in it. The flushing material is carried through bare rock from the juncture at bedrock to the openings underground. This plan has been used, particularly where a cast-iron surface line is laid upon the surface to carry the flushing material from the breaker to the hole, and down the hole continuously, with no opening to the air at the top of the hole, thereby eliminating the necessity of an attendant at this point (Fig. 3). Another similar type of borehole lining is constructed of hexagonal pieces of vitrified brick (Fig. 4). This type requires a steel drive pipe through the surface wash large enough to provide a finished tube of the desired size surrounded by a brick wall about 4 in. thick. The special bricks are laid in cement, six to a circle, around a lubricated pipe used as a form, and lowered in sections inside the large drive pipe; the bottom section is seated in a socket drilled in the solid rock, having the same inside

Jan 1, 1941

By W. T. Cardwell, R. L. Parsons

This paper discusses the practical problem of estimating a single equivalent permeability for an oil reservoir, or a portion thereof, whose actual permeability varies in an irregular manner. Limiting averages for general types of permeability variation are developed, and illustrated by examples involving important, specific types of variation. Introduction The theory of the flow of fluids through porous media1"4 is becoming increasingly important in predictions of oil-reservoir behavior. In practical applications, however, reservoirs are seldom found to which simple theory strictly applies. Actual reservoirs have complicated shapes and nonuniform permeabilities and porosities. This paper discusses the problem of estimating a single equivalent permeability for an oil reservoir, or a segment of an oil reservoir, whose actual permeability varies in an irregular manner. The equivalent permeability of a reservoir segment is defined as the permeability of a homogeneous segment of the same dimensions that would pass the same flux under the same pressure drop- It is the permeability value that can be used in simple theoretical formulas to calculate the reservoir behavior. To the authors' knowledge, previous theoretical calculationst on systems of nonuniform permeability have been carried out only by Muskat'"; and he has not dealt with irregular variations, except in writing down the general differential equation for the pressure in variably permeable systems.lb In practical work, many calculations necessarily have been made to estimate equivalent permeabilities from the permeabiiity profiles obtained by core analyses. Regarding such calculations, Johnston and Sherborne6 say: Simple arithmetic and weighted averages have been tried on many wells and it has been found that, where frequent sampling has occurred, the arithmetic average is as satis- factory as a weighted average. It is possible that the application of statistical methods to the analysis of permeability data as recently presented by Law8 may prove fruitful. L,, has made a valuable contribution in showing how statistical analyses may aid in picturing the characteristics of a reservoir from those of a necessarily limited number of core samples. It is believed however that the particular problem of the estimation of equivalent permeabilities can be most directly approached from a fluid dynamical viewpoint as given in the present paper. An example is presented of the use of the conclusions herein in conjunction with Law's method. Theory In order to approach the problem of heterogeneity simply, it is interesting to consider a square block composed of four smaller, homogeneous, square blocks of porous medium, two of which have a

Jan 1, 1945

By E. S. Greiner

STUDY of the plasticity of germanium or other semiconductor crystals affords unusual opportunities to extend our knowledge of deformation mechanisms. Crystals are available having extraordinary perfection and very high purity. They deform by slip on the systems {111} <110>,1-3 as do crystals of the simple face-centered-cubic structure. Dislocations generated in them during slip are easily revealed in the form of etch pits on either (111) or (100) surfaces.4,5 This fact alone makes possible more detailed studies of mechanisms than is usually the case with metals but, even further, the effect of deformation on their electrical conductivity is very large compared with metals. This comes about not only because the mobility of the charge carriers is reduced, as in deformed metals, but also because the number of these carriers is greatly altered. This latter effect seems closely related to the formation of both line and point imperfections during deformation and thus provides a needed tool for the study of the kinds and distributions of these imperfections. Other investigators have deformed germanium at elevated temperatures by bending,1, 6-8 compres-sion,6, 0,10 tension,2,3,6,11,12 torsion,23 and indentation." Wang and Alexander" have also reported successful indentation at room temperature. Dislocation etch pits consequent to deformation have been observed and studied.7,8,10,18,14,20 The experiments to be de- scribed here include principally the compression and the subsequent annealing of germanium with concomitant studies of etch pits, microstructures, and electrical properties. Both single crystals and heavily twinned specimens were used. Some indentation studies are included. Experimental Methods Plastic compression was effected in the apparatus shown schematically in Fig. 1. It consists of two tantalum platens contained in a helium atmosphere and so arranged that pressure can be applied by a hydraulic press. The specimen between the platens is heated by the surrounding furnace. The specimen is usually a small crystal cube about 0.30 in. on an edge. A control specimen is always inserted so, that it is subject to the same thermal cycle as the one being deformed. This serves to detect any impurity contamination that might accompany the thermal treatment. For high temperature work, where such impurity contamination often occurs, the specimens were first plated with gold whenever subsequent electrical properties were to be determined. This method" is effective in preventing significant contamination of germanium up to temperatures at least as high as 750°C, as evidenced by the constancy of the electrical conductivities of control specimens subjected to the same heat treatments. The total range of temperature used for deformation was from 375°C, the lowest at which significant flow was observed, up to 900°C. Microscopic examination was made after mechanical and chemical polishing and etching. Dislocation pits were revealed with CP-4 etchant by the tech-

Jan 1, 1958

By Edward B. Durham

The refinery at the San Francisco Mint takes the bullion purchased by the receiving department, and carrying Illore than 200 parts of precious metals in 1,000, or, in mint parlance, over 200 fine, and separates and refines the various metals contained therein, using electrolytic processes exclusively. Bullion containing silver is treated in cells charged with a nitric electrolyte. These cells produce fine silver and leave a residue rich in gold. The residue from the silver-cells, together with crude gold-bullion, is treated in cells having a chloride electrolyte. These produce fine gold and leave a residue containing silver chloride. The latter is reduced to the metallic state with zinc and is then treated in the silver-cells. The various waste solutions and the wash-waters, after being freed from the bulk of their precious metals, still contain copper and other metals. These are removed by scrap-iron, and are then treated in the copper-cells, having a sulphate electrolyte. These cells produce pure copper, and collect a residue containing lead, some gold and silver, and all the metals of the platinum gronp that were in the bullion. This residue is relatively small, and is melted into bars and stored until suEcient accumulates to warrant treating it for platinum, etc. The refinery occupies three large and three small rooms. The large ones are, a melting-room, 30 by 34 ft.; a cell-room, 39 by 46 ft.; and a wash-room, 30 by 33 ft. The small rooms are used as foreman&apos;s osce, laboratory, and , re- spectively. The methods here described are those in use in December, 1909, when notes for the present paper were taken.

Jan 1, 1912

By James Herbert Bartlett

The MANUFACTURE of Iron in the PROVINCE of Quebec. The St. Maurice Forges.—The deposits of iron-ore in the St. Maurice district, in the rear of Three Rivers, were probably known to the Indians and .Jesuits, but it is not till 1667 that any discovery is reported. The affairs of the colony were then in the control of the " West India Company," who amongst other monopolies had a right to all mines and minerals." Specimens of the iron-ore were examined in Quebec. in 1668 by the Sieur la Potardière, who reported unfavorably on them. In 1671, Louis de Buade, Comte de Frontenac, was appointed governor of La Nouvelle France ; and in the original manuscripts relating to his administration some allusion is occasionally found to the St. Maurice iron mines.? In a letter to the Imperial Government, dated 2d November, 1672, he says: "The iron mine of which I have already spoken is of great consequence. I have visited it myself, in order that I may be enabled to give a more accurate account of its nature. I am gratified to learn that another mine has been discovered in Champlain, which is much richer than the Cap de la Madelaine mine, and the ore is in greater

Jan 1, 1886

By Charles W. Tandy, Wm. I. Weisman

Sodium sulfate is an important industrial chemical, being one of perhaps a dozen or so chemical commodities that are produced and consumed in the United States in quantities exceeding one million short tons per year. In recent years over half of the country&apos;s production of sodium sulfate has come from natural sources, whereas 20 years ago only 25% was derived from these sources. Production of natural sodium sulfate from various types of deposits is the main source of this chemical in Canada and Mexico, and probably in Argentina, Chile, and the USSR. [Table 1] illustrates the growth in production of natural sodium sulfate in the United States. Mineralogy and Physical Properties Sodium sulfate is widespread in occurrence and is a common constituent of many mineral waters, as well as seawater. Many of the saline or alkali lakes throughout the world contain varying amounts of sodium sulfate. In its natural form it is found as the hydrous salt, mirabilite, commonly called Glauber&apos;s salt, and as thenardite, the anhydrous variety. The largest quantities occur in the form of mirabilite. Sodium sulfate is found in varying degrees of purity, from theoretically pure efflorescent crystals of mirabilite to combinations and admixtures of other salts and impurities. It is a common constituent of some brines, and it is from this source that much is extracted commercially. Sodium sulfate is also found combined with other compounds, such as the mineral glauberite, the double salt of anhydrous sodium and calcium sulfate, and blödite, the double salt of sodium sulfate and magnesium sulfate. While these and other minerals containing sodium sulfate are not economically important, they are of interest because of their frequent occurrence. The reader is referred to other publications (Cole, 1926; Dana, 1932; Grabau, 1920) for descriptions of these minerals. Only the two economically important minerals, mirabilite and thenardite, will be described herein. Mirabilite, Na2SO4 • 10H2O, contains 55.9% water of crystallization. It is noted for its efflorescence or spontaneous loss of water. On

Jan 1, 1975

By B. M. Larsen, L. S. Darken

SOME years ago we collated all laboratory data then available to us on the distribution at equilibrium of manganese and of sulphur between metal and simple slags, and used the results in setting up an equation, which proved to be in accord with determinations of the distribution ratio of manganese and of sulphur between liquid steel and open-hearth slag, over a wide range of operating conditions. We now present an outline of our calculations and inferences on these two closely related questions, which are of especial importance because of the advisability of conserving manganese wherever possible. In general, our results show that in the open-hearth furnace equilibrium between metal and slag, with respect to both manganese and sulphur, is substantially attained during the finishing period of the heat, or in about a half hour to an hour after any additions were made. This implies that the end result will be identical whether manganese is added as alloy or metal to the liquid steel or as oxide to the slag. The proportion of total manganese retained by the steel is favored: (I) by use of the minimum amount of lime, consistent with other operating limitations, required to give a lime-silica ratio of about 2.4, which usually corresponds to a minimum practical slag volume; (2) by a high concentration in the slag of MnO relative to FeO; (3) by high operating temperature. Absorption of sulphur by the slag from the liquid metal is favored: (I) by large slag volume; (2 by a high concentration of active (or "free") lime and of manganese oxide dis) solved in the slag; (3) by low concentration of silica, iron oxide, and phosphate dissolved in the slag. DISTRIBUTION OF MANGANESE BETWEEN SLAG AND METAL AT EQUILIBRIUM On the basis that the distribution of manganese between liquid steel and slag is controlled by the reaction [FeO + Mn = MnO + Fe [A]slag metal slag metal] the distribution at equilibrium, at a given temperature, is expressed by the equilibrium constant for this reaction, which is defined as [K" aMoO aFeI1 dFec) aMn] where a is the activity of the molecular species denoted by the subscript. The activity of each of the several components, although it is not known precisely, is approximately equal to the concentration of each component expressed as its mol fraction; that is, as the ratio of the number of mols of the given component to the total number of mols of all the molecular species present in the metal or slag, as the case may be. Moreover, since the activity, or concentration, of iron in the liquid metal is in fact substantially constant, the term [afe] may be combined with K" to give a new constant K&apos;. Making these changes,

Jan 1, 1942

By R. E. H. Pomeroy

Early in 1917, it became evident, owing to existing and pending market conditions, that a substitute for crude petroleum must be found for firing the smelter furnaces. After a review of the plants then existing, it was deemed advisable to depart from their practice and to adopt the following described system of distributing pulverized coal to the furnaces. The principal advantages of the proposed system, which influenced this decision, were: (I) Equal safety; no pulverized coal is stored at the furnaces; (2) greater ease of operation, furnace fires being controlled by regulating valves in burner branches, as in gas firing; (3) better organization; all machinery, including pulverized coal feed, is under one roof, and the organization is separate from the furnace department; (4) greater cleanliness; all machinery is under vacuum; (5) greater flexibility of application, the coal and air mixture can be piped where needcd. The design of the plant is the result of the combined efforts of the local engineering staff and of the machinery manufacturers. Many new features were embodied in this design to insure greater safety, cleanliness, and efficiency of handling. After 14 months of continuous operation, the plant has proved entirely satisfactory. The building is of structural steel, covered with corrugated steel, with many windows and is painted light gray inside and out. The building floor is of concrete with ample drains to the sewer, and the building is equipped with fire and service water piping. Fig. 1 shows the east side of the building and the incline conveyor from the raw-coal bins. The plant is operated entirely by electric power. All alternating current is 550 volts, 3-phase, 60 cycles. The pulverized-coal feeding niotors and control mechanism are operated by 220-volt direct current supplied by motor-generator sets in the building. Autamatic push-

Jan 1, 1921

By F. C. Stanford

The work of an engineer is to direct natural forces so that the: bring about the results that he wishes to secure. Heretofore he ha concerned himself chiefly with physical forces and inanimate objects until he has secured a truly marvelous degree of control over them The great problem of the present age is to secure a like degree of know1 edge and control of the human factor. Progress has already been made along this line, but it is only a beginning. Wilhelm Ostwald says tha scientific knowledge enables a man to be a true prophet; but it must be remembered that a good many people do not seem to be able to main tain a high average in prophecy. In short, &apos;the average of knowledge is not equal to the average needs of the present time, but continually fails to keep pace with it. It has been aptly said that the really essentia need of the period is for more brains; if we only had sufficient knowledg and sagacity we could not only solve all difficulties, but prevent then from arising. This generalization holds good for an industrial organization. Th most vital need of the management is for more brains. The logica course for an engineer in charge of an industrial organization is, therefore to direct whatever forces may be at his command toward the development training, and guiding of all the brains in his organization. This is easie said than done, for it involves the carrying on toward two objective: the maximum of productive work, and the development of the individual who perform it. This is essentially like the rebuilding and enlarging of plant, keeping it in full operation the while. On the other hand, if th aim is merely for maximum production from an organization, withou offering opportunity for development, the final outcome will necessari be like that of a plant that is driven at full capacity without stoppin for repairs or improvements; it eventually becomes so run down th either a complete rebuilding is necessary or else it has to be abandone

Jan 1, 1918

By H. I. Aaronson, H. A. Domian

The self-diffusivity of Ag10 has been measured as a function of temperature and composition in AgMg. a CsCl-type intermetallic compound with a substitutional defect structure on both sides of the stoichiometric (50 at. pct Mg) composition. These measurements show that In D increases linearly, and both In Do and Q decrease linearly with deviation from stoichiometry. The slopes of these lines are significantly steeper in magnesium-rich alloys. Equations for the variation of Q with composition have been derived by application of the theory of random walk processes on the assumption that diffusion in compounds of this type takes place by the six-jump cycle mechanism of Huntington, Elcock, and McCombie. The favorable agreement obtained with experiment furnishes fresh support for the correctness of this assumption. A principal result of this treatment is that. although the concentration of vacancies is considerably higher in the silver sublattice than in the magnesium sublattice, the acfivation energies for movement of the magnesium sublattice vacancies are so much lower that these vacancies are responsible for effectively all diffusion of silver in this compound. A tendency for vacancies of both types to be kinetically bound to wrong atoms is also noted. THIS study was undertaken to examine the influence of substitutional defects upon self-diffusion in an intermetallic compound, AgMg, with a CsCl-type crystal structure. The CsCl structure is exception- ally simple. At the equiatomic or stoichiometric composition in a binary alloy, it consists of two interpenetrating simple cubic sublattices, each of which is exclusively populated by the atoms of one species. When atomic size and other factors are favorable, deviations from stoichiometry can be entirely accommodated by the substitution of atoms of the species present in excess of 50 at. pct on the sublattice of the other species on a one-for-one basis. Under this condition, the only vacancies present are those formed by thermal activation. The excess atoms thus incorporated into the sublattice of the minority species may be considered as substitutional defects in this sublattice. Several X-ray studies have shown that the defect structure of AgMg is entirely of the substitutional type on both sides of the stoichiometric composition.1"3 The thermodynamic investigation of Kachi indicates that, aside from a low level of thermal disorder and these constitutional defects, order is maintained to the solidus temperature. This compound is therefore a particularly useful vehicle for a study of the influence of substitutional defects upon diffusion kinetics. Other advantages of AgMg for this purpose include: the broad composition region, as much as approximately 10 at. pct on either side of the stoichiometric (50 at. pct Mg), in which the compound is stable; the comparatively low temperature range of the solidus (820°C and below),5 making diffusion anneals near this range experimentally convenient; the reasonably good machinability of the compound, permitting utilization of the standard sectioning method of radiotracer analysis; and the availability of a good tracer, A for one of the constituent species. While this investigation was in progress, Hagel and westbrooks reported data on the self-diffusion

Jan 1, 1964

By Francis F. Lucas

A microscope objective of given numerical aperture, when used with light of given wave length, has some fixed limit of resolution. This may be expressed as potential resolving ability—the ability to resolve is inherent in the lens but whether this limit is achieved in practice is quite another matter. Nearly 50 years ago Abbe evolved theoretical considerations which indicated that the ability of a lens to resolve detail is directly proportional to twice the numerical aperture of the objective and inversely proportional to the wave length of the light used. It is true, unquestionably, that as the numerical aperture of the objective is increased the potential resolving ability of the lens is increased and likewise when the wave length of the light used is decreased, the degree of resolution is increased. Whether Abbe&apos;s formula expresses the exact relationship is not a matter of great concern. It suffices to know that to improve resolution, other things being equal, two avenues of approach are available. Either the numerical aperture of the objective may be increased or the wave length of the light decreased. With the apochromatic system it is possible to employ successfully wave lengths from 400 to 500 uu and still secure reasonably short exposures. The present limit for numerical aperture is 1.40 N. A. although objectives of 1.60 N. A. are now an experimental possibility for metallurgical work. Thus certain well defined limits are set for those who work within the range of the visible spectrum. In order to take advantage of the increase in resolving power which accompanies a decrease in the wave length of light employed, Dr. A. Kohler and Dr. M. Von Rohr of the Zeiss Scientific Staff developed the "monochromats." These are quartz objectives corrected for the single wave length 275 uu which lies in the ultra-violet region of the spectrum. They also developed a series of quartz oculars and a complete photo-micrographic equipment with which to use the quartz optics. Quartz must be used for the optical parts because glass absorbs ultra-violet light almost completely. Thus there was made available about 20 years

Jan 1, 1926

By L. E. Mannion

Sodium carbonate (soda ash) is one of two principal commercial alkalis. Its principal competitor is sodium hydroxide. The use of sodium carbonate is recorded in ancient Egypt, where naturally occurring brines and solid salts provided impure soda for early glassmaking. Until the 19th century, soda ash (as well as potash) was recovered mainly by leaching wood or other plant ashes. In 18th-century Europe, for example, leaching seaweed ash with hot water produced a brown laundry lye. One of the better grades of this material was a Spanish product, barilla, which analyzed 24 to 30% Na2CO3 (Hou, 1942). The modern chemical industry was born in 1691 with the LeBlanc process for making sodium carbonate from salt, sulfuric acid, and lime. English industry used this process extensively in the 17th and 18th centuries. The next major advance was in 1863, when Ernst Solvay devised the ammonia-soda, or Solvay process. The first of many Solvay plants was built in 1874. These supplanted the LeBlanc method and dominated worldwide soda ash production until 1974, when mined sodium carbonate became predominant. Although considerably less important until recently, natural sodium carbonate deposits historically have supported small soda ash operations throughout the world. Shortages during World War II stimulated production of "natural" soda ash from such deposits, particularly at Searles Lake, CA and Lake Magadi, Kenya. More spectacularly, increased production from the vast trona deposits in Wyoming has virtually supplanted the Solvay process in the US. Principal producers of natural soda ash as well as the character of the source deposits are listed in Table 1. [ ]

Jan 1, 1983

By Fred W. Gordon

Apart from the character of pig-iron to be manufactured, other than that it shall be well reduced and open-grained, the selection of the materials should be such as to produce it at the lowest cost. As a rule, the sources of fuels and limestones are not so extensively varied as those of the ores. Many Eastern furnaces are now using Lake Superior ores, and but recently a part of the supply came from foreign ports. It is, however, of the highest importance that the character of fuels and limestones, as well as ores, should be carefully considered in determining their value and making judicious selection among those available. The formulas here offered are based upon the assumption that the heat-requirements for a given mixture are measured by a constant required by the oxide of iron, added to that required for a unit of slag, multiplied by the weight of that slag per unit of iron. The heat-requirements for oxide of iron per unit of pig-iron made are assumed to be 2854 centigrade units. This is taken from the careful analysis of Sir Lowthian Bell, and, so far as the writer is able to determine, is very nearly correct. Dividing this by the quantity of heat that may be evolved and utilized within the furnace per unit of carbon, determines the quantity of carbon required per unit of pigiron ; and if to this be added the quantity of carbon absorbed by the pig-iron, the total requirements in carbon are determined, on the assumption that pure oxide of iron is reduced with pure carbon by the ordinary process of the blast-furnace. Calculating the quantity of slag that would be made from a given mixture of ores, smelted with a given impure fuel and fluxed with a given impure limestone, multiplying this weight of slag by the heat-requirements of its unit (taken at 1050 C. H. U.), and dividing the product by the heat-units evolved and utilized within the furnace per unit of carbon, will determine the quantity of carbon required per unit of pig-iron for the slag.

Jan 1, 1893

By C. Scala, F. Bernstein

General expressions are derived relating the streaming potential to the electrochemical potential of a permeable junction separating two electrolytic solutions. By the methods of irreversible thermodynamics, these potentials are related to the flux of mobile species arising from differences in pressure and chemical composition. The flux is conveniently expressed as a transference number, the equivalents of a mobile species transferred through the junction per faraday of electricity. At constant pressure, the flux equation gives the electrochemical potential across the permeable junction. The streaming potential across the junction is obtained by imposing the condition of constant chemical composition. The familiar expression for the borehole SP is shown to be a particular solution of the general flux equation. The derived exprersions were verified in experiments with seven shale samples. Both the theory and experimental data provide additional proof of the presence and magniturle of the streaming potential in shales. INTRODUCTION In the interpretation of electric logs, there has been much concern over the correction to be made to the recorded SP for an electrokinetic or streaming potential originating from the difference in pressure between the mud column and the formation. It was long recognized by M. R. J. Wyllie that such an electrokinetic potential source mas in the mud cake opposite permeable sands.&apos; More recently, M. Gondouin and C. Scala2 showed an additional but opposing electrokinetic source of potential to be in shale beds. Their work was supported by the very extensive and excellent work of Hill and Anderson.3 n the present contribution, the general relationships between the electrochemical potential and the corresponding streaming or electrokinetic potential are examined and clarified. A notable advance towards understanding the relation between the various sources of electrical potential in a borehole has been the application of the now common methods of irreversible thermodynamics to describe the passage of ions and water through charged electrolyte junctions such as in shales.&apos; The advantages of these methods are twofold. Unlike classical thermodynamics, they can be applied to non-equilibrium sys- tems, i.e., systems in which flow takes place, provided the flow processes have reached a steady state. They also permit conventional thermodynamic properties to be related to the steady-state dynamic properties. These methods arc used here specifically to derive expressions relating the potential behavior of shales in terms of ion and water transport. Experimental verification of the expression for the shale streaming potential is given which in turn offers theoretical support to the existence of a streaming potential in shales.&apos; Importantly, the relative contribution of transport parameters to the SP is clarified. The theoretical treatment is essentially that of Lori-mer, Boterenbrood and Hermans3 ut has been extended to derive the general expression for the SP.

By R. J. Piros, Brusenback, D. A. Dahlstrom

DEWATERING fine coal has been a serious problem to many operators who desired to wet-wash finer sizes and maintain high recovery. Centrifugal driers have become popular for this purpose for sizes between 3/8 in. and 14 mesh. Below 14 mesh the perforated screen centrifuges lose a large per- cent in the effluent solid bowl types that do retain -14 mesh coal, produce excessive degradation, tend to retain the highest ash fraction in any size fraction, and are subject to abrasion, which results in higher maintenance. In 1949 Truax-Traer Coal Co. planned a cyclone installation at their Ceredo preparation plant to recover coal down to 150 mesh with approximately a 14-mesh top size. Since available centrifugal equipment was not considered satisfactory, an investigation of rotary vacuum filters was begun in cooperation with the Peterson Filters and Engineering Co. to determine the suitability of the Peterson Top Feed Reservoir (TFR) filter. This investigation, which is described below, has resulted in a highly satisfactory installation of two 6x10-in. Peterson TFR filters that have been in operation over a year. After some preliminary laboratory batch vacuum filter tests, a pilot plant double-drum Peterson TFR filter was installed at Ceredo to prove the feasibility of vacuum filtration and determine optimum conditions. The full scale units were then installed on the basis of the pilot plant results. This was followed by an extensive research program on vacuum filtration in the laboratory at Northwestern University to investigate basic design and operating variables and their influence on final moisture con- tent of the filter cake. A method of scale-up from laboratory batch tests to the full-size unit was also proposed and proved. Because of the importance of dewatering fine coal today, it was felt that the results of the three steps should be made available for the use of others facing this problem. The work at Northwestern is given in a theoretical section following the discussion of the pilot plant and full- scale operation. Fig. 1 is a flow diagram of the cyclone and filter installation. The feed is drawn from below the

Jan 1, 1952

By T. Egleston

ALTHOUGH the success of metallurgical operations depends so largely on the possibility of finding proper refractory materials, which enter so prominently into the cost of their operations, it can hardly be said that our knowledge of them is in a very satisfactory condition, or even that we know very much about them, beyond a few facts which have been gathered through their use. Experience, as a general thing, is an excellent master, but the requirements of * This article was written at the suggestion of the Committee of the Institute on Refractory Materials, with a view of calling attention to the anomalies and difficulties of the subject. It was hoped that its discussion would eventually lead to the appointment of a Commission, by the great metallurgical interests of the United States, to investigate the whole subject, since it is believed that a better and cheaper artificial product can be made than any now in use, and that many other important incidental results would be accomplished by such an investigation.

Jan 1, 1876

By Juanito C. Fernandez

INTRODUCTION The Philippines is endowed with mineral resources, much of which still remains unexploited. The country&apos;s known reserves, at least for the major mineral commodities, have increased every decade since the first major discoveries more than 80 years ago. Mining, therefore, naturally evolved as one of the pioneer industries and has ever since been a major factor in economic development. The Philippines has entered a new era in mineral resources development and management. One significant feature of this era is the degree to which the government is involved with the industry. In recent years, the state has increasingly encouraged the private sector to carry out detailed exploration aided by governmental contributions through extensive geological and geophysical surveys, fundamental researches and even indirect financial assistance in some specific areas. Significant changes in mineral resources development policies were brought about with the promulgation of Presidential Decree 463 or the Mineral Resources Development Decree of 1974. The Decree provides for a more rational system of administration and disposition of mineral lands to promote mineral resource exploration and exploitation. Various forms of incentives are provided. Foreign entities are allowed to participate in development through service contracts with leaseholders or with the government in the case of reserved areas. The thrust in mineral resources development has been focused on the base metals which as envisioned would provide the foundation for sound economic development. In recent years, however, major strides have been made to promote the exploitation of the non-traditionally produced commodities especially the non-metals. Development likewise point to the growing determination of the government and the private sector to expand benefits from mining. This is evident in efforts to promote downstream processing operations and to encourage investments in exploration, exploitation and mineral processing ventures. The integrated mineral resources development plan, therefore, proposes the vertical integration of mining extraction activities with the processing requirements of the metal-based manufacturing industries. While mining activities shall continue to be carved out by the private sector, the government shall influence the industry&apos;s direction by establishing legitimate goals to maximize benefits through an integrated approach giving due consideration to environmental protection and resource needs of future generations. STATUS OF MINERAL RESOURCES DEVELOPMENT Extent of Exploration Application of modem exploration tools and concepts complemented by intense infusion of foreign technology and rapid development of indigenous expertise have enabled the government jointly with the private sector to geologically explore vast grounds and to expand the country&apos;s known mineral resources. Approximately 93% of the country&apos;s total land area of 30 million hectares have been geologically mapped on at least 1:250,000 scale. Of the 93% total coverage, roughly 37.54% or 11.07 million hectares have been done on scales of 1:10,000 to 1:50,000 as shown in Figure I. Only 3.07% of the total coverage have been surveyed in detail. Land gravity surveys have been undertaken on over 45% of the total, while some 77,300 line km. of aeromagnetic surveys have been flown over 110,000 sq. km. of land area. Processing of data is almost complete. Total magnetic intensity and IGRF-corrected maps are available. Geological interpretation utilizing Landsat MSS imagery and low altitude aerial photography augmented by ground truthing have been undertaken in several large areas with very encouraging results. Beach and offshore mineral surveys were initiated in 1977 and have covered substantial areas in northwest and southeast Luzon and northeastern Mindanao. Highly promising areas for detrital magnetite, chromite, gold and some heavy minerals including ilmenite and titanium have been identified. In the petroleum sector, two offshore oilfields are currently producing from Miocene limestone reefs in Northwestern Palawan. Another field from the same area will be on stream in mid-1982.

Jan 1, 1982