Search Documents

By J. E. Huzarevich, R. M. Leibrock, R. G. Hiltz

The various factors considered in recommending the initiation of a gas injection project in the southern portion of the Cedar Lake Field are discussed. Performance history under gas injection operations is reviewed and these data are analyzed, utilizing both the material balance method and the fractional flow and frontal advance expressions. Results of the analysis of the performance data indicate that the injected gas has contacted and affected at least 60 per cent of the reservoir and a substantial increase in ultimate recovery can reasonably be expected. By holding the reservoir pressure appreciably above the bubble point, the well productive capacities have been maintained substantially above the level predicted for primary operations. The analysis of the Cedar Lake project suggests that in certain limestone reservoirs, at least, the probable success of gas injection cannot be predicted simply from ohservation of permeability distribution throughout the pay section, as indicated by core analysis data, on either one or a number of wells. Further, the performance of this particular project fails to indicate any basis for classifying carbonate reservoirs in general as being inherently unsuited to a dispersed type gas injection program, thus indicating that each reservoir should be considered on its own merits, regardless of the composition of the reservoir rock. INTRODUCTION Early in the life of the Cedar Lake Field, an extensive data gathering program was initiated to provide an accurate record of reservoir performance characteristics. From the study of these data it was apparent that there was a critical need for supplementing the natural reservoir energy in order to maintain well productivities and obtain the maximum ultimate oil recovery. Accordingly, detailed engineering studies were made of the various methods of secondary recovery which might be applicable. As a result of these investigations, the decision was made to initiate a gas injection program of sufficient intensity to maintain reservoir pressure at approximately 600 psia, or some 274 lb above the bubble point pressure of 326 psia. A full scale dispersed type gas injection program has been in operation on leases of the Stanolind Oil and Gas Co. in the southern portion of the field for nearly five years, and sufficient performance data are now available to evaluate the benefits which have been derived from this project. It is the primary purpose of this paper to analyze the performance data for the Cedar Lake gas injection project and to point out the significance of the ohserved behavior with respect to certain hypotheses which have been advanced in recent years concerning the probable success of gas injection projects in limestone reservoirs. This paper properly should be regarded more on the order of a progress report, inasmuch as some revision in interpretation will undoubtedly be required from time to time as additional performance data are obtained, although the satisfactory performance of the project to date leaves little doubt as to the ultimate success of gas injection in the Cedar Lake Field. As a result of the success of the project to date, a unit was formed in the southern part of the field, effective March 1, 1951, for the purpose of continuation of the gas injection program. Participants in this unit are the Mid-Continent Petroleum Co. and Stanolind Oil and Gas Co. GEOLOGY AND STRATIGRAPHY The Cedar Lake Field is located in the northern portion of the Midland Basin area as shown in Fig. 1. The southwest portion of the field lies within a playa, or dry salt lake, which covers an area of approximately eight square miles. As might be expected, it was this lake which furnished the inspiration for the name of the field. Except for its value as a salt water disposal pit, this lake has succeeded only in magnifying the difficulties in developing this portion of the field. Typical of this section of West Texas, the area in general is relatively flat and has a semi-arid climate. The localized structure which favored the accumulation of oil is an anticline with approximately 100 ft of closure. The major axis of the structure extends in a general southeast-northwest direction. Originally this structure was defined by seismograph data, which have been subsequently confirmed by development. In general, the geologic column is typical of that found throughout the basin. From the surface to depth of approximately 1,800 ft, surface sands and undifferentiated red beds. probably Triassic. are encountered. Below this point to the producing horizon, all formations are of the Permian age.

Jan 1, 1951

By M. Schmellenkamp

By comparing two longwall operations, one begun in 1956 and the other in 1960, the author is able to demonstrate the increases in production and performance made possible by longwall mining. These achievements have been brought about by continuous development of longwall mining equipment and associated roof supports. Because of this progress, longwall mining is able to provide, under proper conditions, high production per man-shift, remarkable cost savings, dependable roof control, safe working conditions and truly continuous production. It may seem odd that the title of this paper is not simply "Longwall Mining" but instead "Progress in Longwall Mining." However, the word "Progress" definitely has its place in longwall mining. If it had not been for progress in the development of longwall mining equipment and roof supports, the longwall mining method would not be able to compete in production and performance with modem coal mining machines. The longwall mining method was practiced at the beginning of the century and there were several successful operations in coal fields in Illinois. In those early days of longwall mining, the coal was undercut by hand 2 to 2.5 ft at the bottom of the seam and packwalls were built in the gob to support the roof. The roof eventually subsided and the weight of the subsiding roof was used to ride the face and break the undercut coal. Utilizing natural weight to soften the coal face is still practiced in modern longwall mining; however, the packwalling method has been replaced by the caving method and the roof is now supported by yielding steel roof supports and forepoling steel headers. The purpose of these yielding-type roof supports is to provide a safe working area for the crew along the entire longwall face, to permit continuous mechanical mining across the prop free face, and to provide a strong resistance for the roof by forming an even breaking line at the gob for the roof to cave. Roof supports and associated forepoling headers should be kept as close as possible to the face in order to prevent a caving between face and supports, especially under friable roof. This means that the coal should be extracted in small slices, allowing only a narrow roof area to be exposed and unsupported. The coal planer with its relatively high cutting velocity of 75 ft per min provides such an extraction of coal and has proved its high performance under difficult mining conditions. Since 1951, several longwall faces in southem West Virginia and Pennsylvania which have been equipped with the coal planer and friction-type manual roof supports have been successfully operated. Compared to today's longwall mining, these longwall faces required such a large crew, primarily to handle the roof supports, that the actual high production per shift was charged with too high a labor cost, thereby decreasing the tons per man. Yet, even then the longwall faces outperformed the conventional mining system under the same conditions. In order to demonstrate the progress that has been made in the development of longwall mining, a comparison will be made between a longwall face in Arkansas which was installed in 1956 and a modemized longwall face started in 1960 in southern West Virginia. LONGWALL MINING IN 1956 The 320-ft longwall face was developed in a 32-in. thick coal seam near Greenwood, Ark. The method of mining the 320-ft coal block was the advancing system in which three entries on either side of the face were driven ahead of the advancing longwall face. The face was equipped with a coal planer and a Panzer conveyor; timbering was done with wooden timbers and cribs. The roof supports were set without any pattern. The crew to operate the planer and to handle the roof supports (timbers and cribs) consisted of 15 men per shift. During a period of approximately eight monthsof single shift operating time, the average tonnage produced in this relatively low seam amounted to about 263 tons of clean coal per shift. To show the development in the coal plow from then until now, it should be pointed out that the standard plow was used in this operation. The plow was equipped with rigid bottom bits which could not be adjusted if the plow started to climb, thereby leaving bottom coal to be recovered by pick hammers end causing delays in production. The height of the plow

Jan 1, 1963

By T. M. Allen, W. H. White

THE Greenwood-Grand Forks area of southern central British Columbia, known as the Boundary District, has a long history of mining exploration and production. At the turn of the century this was the premier copper mining camp in the British Empire, its total production amounting to some 20 million tons. Most of this ore came from the great Granby mines at Phoenix, but the Motherlode mine at Deadwood camp, 6 miles to the west, and several mines in Summit camp, 5 miles north of Phoenix, made important contributions. The large deposits were exhausted in 1918 and the district since has seen only desultory exploration and salvage operations. The orebodies are mineralized skarn zones in limestone members of a thick series of Upper Paleozoic sedimentary and volcanic strata. Chalcopyrite is the primary ore-mineral. Copper carbonates and silicates occur sparingly in outcrops, but the oxidized zone generally is very shallow. Much of the surface is mantled by glacial drift which in most places ranges in thickness from 2 to 15 ft. In some of the hanging valleys, however, the glacial drift may be as much as 100 ft thick and may assume drumlin-like forms. In 1951 an ambitious program aimed at the discovery of new orebodies and important extensions of abandoned deposits was launched by Attwood Copper Mines, Ltd. In this district so thoroughly searched by an earlier generation of prospectors, any orebody which had remained undiscovered must have little or no surface indication. Consequently, in addition to the basic detailed geological work, the program of exploration included magnetometer and self-potential surveys. Geological bets and geophysical anomalies were tested further, prior to diamond drilling, by a study of copper distribution in tree twigs and/or in the soil. The soil sampling and analytical methods used and some of the results seem of sufficient importance to warrant this paper. The authors had done some plant sampling in this and other districts, using the dithizone neutral-color-end-point method (Warren and Delavault, 1948, 1949; White, 1950),1-3 but they were unfamiliar with its soil application. Finally, after much experimenting in the field, they adopted the methods described here. These methods are not entirely original or defensible on theoretical grounds, but under field conditions of rapid sampling and analysis the results are reliable enough to be of use. Fig. 1, which shows the results of duplicate analyses of duplicate soil samples taken at 50-ft intervals across an anomalous zone, indicates the relative dependability both of the sampling and analytical methods. Sampling and Analytical Equipment A 2-ft piece of 1-in. solid drill steel, one end sharpened to a broad, conical point. The steel is marked at 1 ft from the point. A 2-ft piece of ½-in. black iron pipe, one end filed to a bevelled cutting edge. The pipe is marked at 1 ft 3 in. from the cutting end. A 3-lb hammer. A plastic or rubberized sheet about 18 in. square. Moisture-proof assay pulp envelopes. A 10-mesh seive made from window screen with the paint burnt off. A small assay spatula. A pan balance sensitive to 10 mg. Two ignition trays about 4 in. square, made of sheet iron turned up along the edges. A Coleman two-burner gasoline stove. An asbestos board about 5x8 in., used as a hot plate on the gasoline stove. A circular aluminum rack to hold 8 test tubes while refluxing (design of Almond and Morris). Pyrex Glassware Large refluxing test tubes, 25x200 mm, marked at 40 ml volume. Breakers, 20 ml. Pipettes, 1, 5, and 10-ml capacity. Graduate, 50 ml. Shaking cylinders, 100 ml, glass stoppers. Burette, 25 or 50-ml capacity, with holder. Chemical Supplies 1 N sulphuric acid. Hydroxylamine hydrochloride, solid crystals. Fisher Alkacid test paper. Copper standard solution. Dithizone standard solution 60 mg per liter. Water reasonably free of metals. Soil Sampling Method: The problem of how to take a soil sample is extremely crucial. The method outlined below, adopted after a number of tests, has the advantages of uniform pattern, uniform depth, and uniform size of sample. The area to be tested was marked off by chain and compass lines 100 ft apart, normal to the strike of possible ore deposits. Numbered stakes were set at 50-ft intervals along these lines and a soil sample was taken at each stake in the following manner. The drill steel was driven into the ground normal to the slope of the surface to the marked depth of 1 ft, moved slightly from side to side, then carefully withdrawn. The iron pipe was inserted to the bottom of this hole, tapped down to the marked depth of 1 ft 3 in. and withdrawn; the 3-in. soil plug in the

Jan 1, 1955

By George Stern

THE purpose of this investigation has been to study one method for making ordinary carbon steel by the powder metallurgy technique. This method con- [ ] sists of pressing and subsequently sintering an intimate mixture of iron powder and graphite in a suitable atmosphere to produce a steel. Two types of iron powder have been studied, electrolytic and reduced. The sintering of mixtures of loose carbonyl iron and carbon black for several hours at 1000° to 1100°C. (1830° to 2010°F.), followed by forging of the resultant ingots to bars, has been studied by Offermann.1 Trail' has reported on the properties of hydrogen-reduced and electrolytic iron powders, both containing 0.5 per cent carbon. Methods for making steel bodies by powder metallurgy have also been sug- [ ] gested by Goetzel,3 who recommends the addition of steel powder of well-defined carbon content to pure iron powder, and Volterra,4 who suggests compaction and subsequent sintering of a mixture of steel powder, iron oxide and iron powder. Additional methods for making steel bodies by powder metallurgy have been reported in the literature by Koehring,5 Allen,6 Balke,7 Wulff,8 Boegehold,9 and others. 10,11,12 It is felt that the method of pressing iron powder and graphite, as described herein, lends itself best to production because of the lubricating action of the

Jan 1, 1946

By George S. Rice

A problem of possible subsidence of the surface from mining operations, which might have had disastrous results, arose in 1913 at the Brier Hill mine, of the Penn Iron Mining Co., near Norway, Mich., now managed by Pickands, Mather & Co. for the Bethlehem Steel Co. A double track and sidings of the Chicago & North Western Railroad passed over part of the mine, and if subsidence had reached the surface it might have affected the stability of the tracks. The chief purpose of this paper is to record the facts disclosed by investigations of underground movement from 1913 to 1919, when the tracks were moved, and subsequently at intervals, as engineering data of value from mining carried on below the tracks in the steeply pitching lenses. A secondary purpose of this paper is to describe a novel method for determining the rate of speed of upward breaking above the mine excavations. This method was found effective and might be used elsewhere under similar conditions. The mine workings under consideration were developed from the Brier Hill shaft, which was circular, concrete-lined, 14 ft. in diameter and about 900 ft. deep. They extended about 800 ft. westward from the shaft, and nearly parallel to a corresponding length of the railroad tracks. The highest part of these workings was at a depth of 400 ft. below the tracks (Figs. 1 to 12). The mining company had the right to remove the ore, the railroad assuming that the surface would be supported. Finally, without legal controversy, an amicable adjustment was reached as to what should be done to lessen or obviate the hazard of subsidence. Method oF Mining Before the problem became acute, the mining company, to decrease the possibility of subsidence, had been mining the part of the orebody that lay under the tracks by a room-and-pillar system, back-filling with

Jan 1, 1934

By T. O. King, Y. P. Gupta

The self-diffusion of sodium in two sodium silicate liquids was measured in the temperature range 850" to 1500°C by the capillary-reservoir technique. Radioactive Na 22 was used as the tracer. The total count and autoradiographic methods were used for determination of the total Na 22 depletion and diffusion profiles of the dqy-used specimens. The diffusion coefficients obtained by the autoradiographic technique are slightly smaller than those obtained by a total count method. Error analysis of the two methods suggests that more confidence be placed in the results of the total count method. The experimental results were analyzed in terms of the existing activated rate process theory. The activation energy for diffusion was shown to decrease markedly as the temperature increased. This was attributed to a variation in the heat of activation with temperature, probably related to a change in the distribution of anions associated wilh the cation. In terms of a model, suggested for diffusion in liquid silicates, differences in the aclivation energies for diffusion and electrical conduction may arise from the effect of the electric field applied in conduction measurements. It is generally accepted that liquid silicates consist of cations and an equilibrium distribution of complex anions determined by temperature and composition. Transport properties in molten silicates are of interest, not merely because of their relevance to the kinetics of pyrometallurgical reactions and glassmak-ing processes, but also because they are useful to development of the theory of such ionic liquids. Self-diffusion is one such transport process that may, if studied for liquid silicates of widely varying compositions, indicate structural changes through changes in the activation energy for diffusion. The self-diffusion of calcium, silicon,' sulfur: aluminum, 4 and oxygenS in lime-alumina-silica melts and of iron6 in molten iron silicates have been measured. Unfortunately, the errors in some of the reported activation energies for diffusion are too large to allow firm conclusions concerning structure and the mechanism of the diffusion process to be drawn. The research reported here was a study of the self-diffusion of sodium in liquid sodium silicates. The soda-silica system was chosen since: i) a reasonable composition range can be covered in the binary system at moderate temperatures; ii) suitable isotopes of sodium (radioactive Na 22 and NaZ4) can be obtained; iii) data on the electrical conductivity and viscosity of sodium silicate liquids are available. However, the range of composition actually used in diffusion experiments was limited, to 20 to 35 wt pct soda, by the relatively high viscosity of silica-rich compositions and by evaporation of soda from basic melts. EXPERIMENTAL PROCEDURE The capillary-reservoir technique was used, wherein a radioactive tracer, Na 22, incorporated in the capillary melt, was allowed to diffuse out of the platinum capillary tube into a large reservoir of silicate liquid containing a chemically identical melt, but without radioactive tracer. After a specific diffusion time, both the total depletion in the tracer concentration and concentration-distance profiles of the diffused samples were measured by procedures to be described later. The diffusion cell assembly was similar to that used by Koros and King.' The temperature of the diffusion cell was measured with a calibrated Pt, Pt-10 pct Rh thermocouple located at the center of the liquid reservoir. The same thermocouple was used to obtain the temperature profile in the reservoir. The temperature at the top of the reservoir was slightly higher (2°C) than that at the bottom, to minimize convection in the capillary tubes, which were placed, open end up, in the reservoir. Convection was not expected to be a problem since the length-to-diameter ratio of the tubes was about 12:1 and the maximum capillary diameter was 1 mm. The diffusion cell was heated in a molybdenum-wire resistance furnace, previously used by Koros and King, but somewhat modified. A Pt, Pt-10 pct Rh thermocouple enclosed in an alumina tube and located near the furnace winding was used in conjunction with a preamplifier and Micromax proportional controller for temperature control, within 4°C, at temperatures near 1500°C. Before starting a diffusion run, the furnace was heated to the desired temperature and an alumina guide assembly for the capillaries was slowly lowered to within 2 cm of the liquid reservoir. The capillaries were thus heated to about the temperature of the bath. The run was started by lowering the assembly till the open ends of the capillaries were about 1 cm below the surface of the liquid. The run was ended by raising the assembly to about 15 cm above the liquid bath. Later, the sample assembly was slowly withdrawn from the furnace. Six diffusion samples were usually run at the same time. Three runs made with the open ends of the capillaries down were discarded because in the majority of these samples air bubbles trapped at the open end were observed. Some glass adhered to the outside of the capillary on withdrawal. This was carefully removed and used to check that the Na 22 activity in the sink remained at a low level. Materials. Nonradioactive sodium silicates were prepared by melting, in a platinum crucible, weighed quantities of sodium carbonate and powdered silica. To prepare radioactive sodium silicates, Na2 obtained in HC1 solution, was first checked for radioactive impurities by obtaining a y-ray energy spectrum, then the chloride ions were removed by anion-ex-

Jan 1, 1968

By George H. K. Schenck

The investment analysis methods that are most generally accepted in the mineral industries in the mid-80's are presented along with their advantages and disadvantages. Also covered are current widely-used practices for introducing the uncertain nature of most of the important variables in an investment analysis, which is contrasted to the former dominance of deterministic analysis. Finally, the discussion turns to current practice for handling the two critical areas: cost of capital and inflation. The advice contained is reinforced with data from a survey of current practices in the petroleum industry.

Jan 1, 1985

By J. H. Scaff, J. E. Kunzler

The measurement of the electrical, thermal, and magnetic properties of metals at low temperatures, primarily in the range of liquid helium below 4.2°K, is a powerful tool for investigating many of the fundamental properties of the metallic state. Such measurements also have many practical applications, particularly as an analytical tool. One example of the practical utility of such measurements is illustrated by a short study we have made of the low-temperature resistance of copper used in preparing varistors. Copper-oxide varistors are prepared by the thermal oxidation of copper. This results in the

Jan 1, 1959

By E. Gregory, A. Coucoulas

Carbm dioxide, which exists metastably as a constantly subliming molecular solid in a normal room-temperature environment, has been shown to exhibit many microstructural features which are similar to those observed in metals and ceramics at temperatures approaching their melting points. An examinution has been made of some of the factors affecting a brittleness condition known as "smzdiness" which occurs in solid carbon dioxide. It has been shown to be highly dependent on manufacturing and storage conditions and is thought to be a marked intergranu-lay brittleness which results from a combination of excessive grain growth and a concentration of gas-filled pores at the grain boundaries. In the course of an investigation carried out to explain certain physical and mechanical properties of solid carbon dioxide, observations were made of the microstructure and fragmentation of samples after fabrication and storage under varying conditions. Many similarities between the structures of solid carbon dioxide observed under ambient conditions and those existing in metal and ceramic systems at temperatures approaching their melting points have been observed. There are, however, important differences between solid carbon dioxide and the common metallic and ionic solids which result primarily from the differences in the nature of the bonding forces. Despite these differences, the relative ease with which certain microscopic observations can be carried out, may make solid carbon dioxide a useful material model for the physical metallurgist and the ceramist. It could also prove a valuable material for educational purposes where it is required to illustrate grain phenomena which normally can only be seen with the aid of a high-temperature microscope, and after prolonged chemical or thermal etching.

Jan 1, 1963

By C. H. Ferguson

The fact that little if anything has appeared in the technical press or in the Transactions of the Institute on the subject of roll shells proper, used in various grinding appliances…

Jan 1, 1915

By Zden[e]k P. Bažant

Due to their heterogeneity, most rocks fracture with a zone of distributed cracking ahead of the fracture front. This makes linear elastic fracture mechanics inapplicable. The present study describes a mathematical model in which the progressive microcracking is taken into account by strain-softening stress-strain relation. In a simpler version of the model, the triaxial strain-softening stress- strain relation is obtained by direct adjustment of the elements of the compliance matrix. This formulation is rigorous only if the principal stress directions do not rotate during fracture formation within the fracture process zone. As a more sophisticated and generally applicable model, the so-called microplane model which is an analogue of the slip theory of plasticity is outlined. Comparison with fracture data for various rocks are given.

Jan 1, 1984

By Jr. E. H. Dix.

In selecting the subject, "Acceleration of the Rate of Corrosion by High Constant Stresses,'' for the 1940 Institute of Metals Division Lecture, I have been influenced by its highly theoretical and speculative nature as well as by the great practical importance of the correct interpretation and appraisal of the engineering significance of the phenomenon. I lay no claim to originality in talking on this topic, since it has been the subject of discussion for over a quarter of a century. However, as our technical thinking advances, old phenomena take on new and more significant aspects. In our studies at the Aluminum Research Laboratories, we have encountered many perplexing and seemingly contradictory results and have been fascinated by the problem of dovetailing all of the many pieces of information to make a complete picture. I hope that in the brief period of this lecture I may share with you some of the enjoyment we have had in attempting to meet this challenge to metallurgical science. The emphasis generally has been placed on the spontaneous failure by cracking of a metal under the combined action of high stress and corrosion, hence the present-day use of the terms "stress corrosion" or "stress corrosion cracking." The older term "season cracking," applied more specifically to copper-base alloys, includes, by inference, the element of time. For the purpose of the discussion today I will use "stress corrosion" to cover broadly the effect of stress in accelerating the rate of corrosion of metals. To stay within the limits of allotted time the disrussiorl will cover the effect of high static stresses rather than repeated or dynamic stresses, which would take us into the related field of corrosion-fatigue. The subject is particularly appropriate for an Institute of Metals Division Lecture because much the same phenomenon has been observed in almost all metal systems. Thus, in addition to the season cracking of brass may also be mentioned the "caustic embrittlement" of steel boiler

Jan 1, 1940

By Jr. E. H. Dix.

In selecting the subject, "Acceleration of the Rate of Corrosion by High Constant Stresses,'' for the 1940 Institute of Metals Division Lecture, I have been influenced by its highly theoretical and speculative nature as well as by the great practical importance of the correct interpretation and appraisal of the engineering significance of the phenomenon. I lay no claim to originality in talking on this topic, since it has been the subject of discussion for over a quarter of a century. However, as our technical thinking advances, old phenomena take on new and more significant aspects. In our studies at the Aluminum Research Laboratories, we have encountered many perplexing and seemingly contradictory results and have been fascinated by the problem of dovetailing all of the many pieces of information to make a complete picture. I hope that in the brief period of this lecture I may share with you some of the enjoyment we have had in attempting to meet this challenge to metallurgical science. The emphasis generally has been placed on the spontaneous failure by cracking of a metal under the combined action of high stress and corrosion, hence the present-day use of the terms "stress corrosion" or "stress corrosion cracking." The older term "season cracking," applied more specifically to copper-base alloys, includes, by inference, the element of time. For the purpose of the discussion today I will use "stress corrosion" to cover broadly the effect of stress in accelerating the rate of corrosion of metals. To stay within the limits of allotted time the disrussiorl will cover the effect of high static stresses rather than repeated or dynamic stresses, which would take us into the related field of corrosion-fatigue. The subject is particularly appropriate for an Institute of Metals Division Lecture because much the same phenomenon has been observed in almost all metal systems. Thus, in addition to the season cracking of brass may also be mentioned the "caustic embrittlement" of steel boiler

Jan 1, 1940

By Henry Tobelmann

THE location, mode of occurrence of ore, and preliminary tests leading to the development of the present leaching process and the building of the present plant on the property of the New Cornelia Copper Co. at Ajo, have been described in previous papers presented to the Institute and in the, discussions thereof.1 It is sufficient to say that these tests began early in July, 1912, and were continued to the close of January, 1916; that small tests at Douglas were followed by the construction of a 1-ton plant at the mine; and this was followed by the operation of a 40-ton plant for 14 mo. In all about 15,000 T. of ore were treated experiment-.

Jan 2, 1919

By Francis H. Crockard

During the past five years we have probably witnessed greater technological advances than in any similar period. Industry and science have steadily marched ahead. The makers of iron and steel products have watched with great interest the development of streamlined trains, faster and safer airplanes, the entirely new science of air-conditioning and the widespread use of stainless steels. Since 1930, we have witnessed the erection of the world's largest suspension bridge, the largest and fastest ocean liner and the spectacular Boulder Dam, while even greater things are planned in these particular fields. Other industries, too, have been moving ahead rapidly. This advance in a few years has been caused primarily by the fierce competition of the depression. Now, more than ever, is the emphasis placed upon quality and service. Makers of southern merchant pig iron have been no exception and have been confronted with increasingly strict chemical specifications and with much greater stress on physical characteristics than ever before. For example, sulfur in the iron must be held very low, competition demanding that it be in the 0.020's and low 0.030's; silicon content must be held within a very narrow range, and definite requirements of phosphorus and manganese are an essential part of the specifications. Physical characteristics are becoming of increasingly greater importance. The introduction of triple-skimmed, slow-cooled iron several years ago was the first step in this direction. Now there are a few customers who buy iron by chemical analysis and physical appearance, having found that the analysis alone is an insufficient guide to their requirements. In addition to questions of quality, the subject of cost has greatly altered the southern furnaceman's viewpoint on many things. Formerly we had low-grade but cheap raw materials, but recent developments, such as greatly increased labor rates, have raised the cost of the same

Jan 1, 1936

By Francis H. Crockard

During the past five years we have probably witnessed greater technological advances than in any similar period. Industry and science have steadily marched ahead. The makers of iron and steel products have watched with great interest the development of streamlined trains, faster and safer airplanes, the entirely new science of air-conditioning and the widespread use of stainless steels. Since 1930, we have witnessed the erection of the world's largest suspension bridge, the largest and fastest ocean liner and the spectacular Boulder Dam, while even greater things are planned in these particular fields. Other industries, too, have been moving ahead rapidly. This advance in a few years has been caused primarily by the fierce competition of the depression. Now, more than ever, is the emphasis placed upon quality and service. Makers of southern merchant pig iron have been no exception and have been confronted with increasingly strict chemical specifications and with much greater stress on physical characteristics than ever before. For example, sulfur in the iron must be held very low, competition demanding that it be in the 0.020's and low 0.030's; silicon content must be held within a very narrow range, and definite requirements of phosphorus and manganese are an essential part of the specifications. Physical characteristics are becoming of increasingly greater importance. The introduction of triple-skimmed, slow-cooled iron several years ago was the first step in this direction. Now there are a few customers who buy iron by chemical analysis and physical appearance, having found that the analysis alone is an insufficient guide to their requirements. In addition to questions of quality, the subject of cost has greatly altered the southern furnaceman's viewpoint on many things. Formerly we had low-grade but cheap raw materials, but recent developments, such as greatly increased labor rates, have raised the cost of the same

Jan 1, 1936

Robert H. Richards, Boston, Mass.: Mr. Goodale calls attention to the difficulty of obtaining clean tailings from the jigs which are fed by the spigots of the hydraulic separator. This difficulty is universally encountered. The Lake Superior copper mills practically overcome it by running the beds of those jigs loose, carrying into the hutch all of the available copper and some sand. These hutches are again jigged upon threesieve Collom jigs, where the treatment is very slow and gentle; and on the successive jigs lighter and lighter bedding is used. The last sieve is run thin enough to let some sand into the hutch. With these precautions most of the free copper is extracted, as well as a fair proportion of the included copper.

Jan 1, 1897

By Douglas Bunting

In the anthracite fields of Pennsylvania, mine fires occur with more or less regularity and their existence is an ever-present hazard in coal mining. In all probability 90 per cent. of the mine fires can be ascribed directly or indirectly to the ordinary miner's open lamp. Other causes may be smoking, electrical installations, gas explosions, gas feeders, and the communication of fire to the outcrops from ash dumps, culm banks, timber and brush fires. Fires in pump rooms, engine rooms, and barns have been largely eliminated as a result of the Act of Assembly, approved June 15, 1911, which provides that all inside buildings, including engine rooms, pump rooms, barns, etc., shall be constructed of incombustible materials. Smoking of pipes, cigars, and cigarettes should be prohibited in the mines and too much care cannot be exercised in preventing fires by enforcing all rules designed for that purpose. Mine fires that involve underground fighting are invariably dangerous, and all fires, irrespective of the method pursued in extinguishing them, involve property loss and expense. Each fire generally presents a more or less original problem, dependent on the particular conditions. Generally mine fires may be divided into two classes: Those occurring in inaccessible workings and those occurring in accessible workings. The methods pursued in extinguishing or controlling mine fires are as follows: (I) direct attack, (2) smothering by sealing, (3) flushing with silt or other solids, (4) flooding with water, (5) cutting off, (6) surrounding with incombustible materials, (7) digging out by stripping from the surface. Most fires arc extinguished in their incipiency by direct attack and failure to extinguish by this method is due to late discovery, lack of water, and facilities for fighting, or improper procedure in the initial attack. Should the method first pursued be unsuccessful, careful consideration should be given in determining next the method to be adopted; then the work should be carried on as rapidly as possible and under the supervision of the most competent persons. Materials and supplies should be furnished without delay and in sufficient quantities for the work to be accomplished.

Jan 1, 1922

By J. Nagy, D. W. Mitchell, E. M. Murphy

In 1957 research was initiated in the U.S. Bureau of Mines experimental coal mine near Pittsburgh, Pa., to study factors affecting foam generation and transport, to evaluate the effectiveness of high-expansion foam for controlling mine fires, and to develop techniques for applying the method under U.S. mining conditions. These investigations showed that high-expansion foam containing at least 0.2 oz of water per cu ft of foam is effective in controlling experimental underground fires burning coal, wood, and oil. Sometimes the fire was completely extinguished, but more often, it was brought under sufficient control to permit either a direct attack on the fire with a stream of water or loading of the hot material into cars. A progress report' prepared in July 1958 summarized the initial achievements of the USBM experiments. Since then other phases of the foam-plug method for attacking fires have been studied in the laboratory and in the mine. Previous studies by British engineers' of the foam-plug method for fighting mine fires indicated that high-expansion foam was effective in controlling experimental timber fires in an underground passageway. Their subsequent workx-1 pertained to the practical aspects of fighting large fires within a mining area with a foam-plug. CONTROLLING EXPERIMENTAL FIRES In the USBM tests foam was formed by spraying a dilute solution of a foaming agent on a metal or cotton net of 1/8 to 1/4-in. mesh. Air passing through the continuously wetted net forms bubbles of 1/2 to 11/2-in. diam and produces a honeycomb of foam that fills the passageway. Under the ventilating-air pressure, this light-weight plug moves forward through the passageways, around sharp corners, and over obstacles. as illustrated in Fig. 1. High-expansion foam was transported to a wood fire, an oil fire, and 13 coal fires. Figs. 3 and 4 show a typical coal fire before and after attack with foam. In 12 of the 15 experiments the fire was brought under control when the water content of foam was 0.2 oz or more per cu ft. A fire was considered controlled when the flames were quenched and observers could cross the area without wearing breathing apparatus or protective clothing. In the other three experiments, conducted when the water content was less than 0.2 oz per cu ft of foam, the flames were retarded but the fire was not controlled. Coal fires have been attacked successfully by foam introduced at points varying from 155 to 1010 ft from the fire. The time of burning in coal beds 10 in. thick ranged from 11/2 to 5 hrs or more. Most of the experimental fire beds were 15 ft in length. However, in one experiment a floor fire 25 ft long and 5 ft wide was constructed $5 upwind from another fire 15 ft in length; in another instance, the fire was 100 ft long and 5 ft wide. Foam was applied to the fires for periods ranging from 7 to 36 min. The time required for foam application depends on the extent of the fire, time of burning, water content of foam, foam velocity, and degree of fire control desired. In addition to the coal fires, foam was transported to a fire covering 45 sq ft, produced by 15 gal of oil burning in metal trays on the floor. The foam extinguished the oil fire in about 1 min. In one other test, the burning of 1100 lb of dry sawmill slabs stacked in open cribs 4 ft high and 16 ft long was brought under control by foam in 2 min. Composition of Gases in Return Air: In several of the experiments samples of the return air from fire zones were collected; composition of the atmosphere before, during, and after foam application was then determined. Because of condensation in the relatively cool sampling tube, the amount of water vapor was not determined. Analyses showed that concentration of carbon dioxide and combustible gases increased as the foam began passing over the fire. This resulted from the decrease in the volume of air when foam generation started and from the formation of gases when water reached the fire.* The quantity of gases generated would not be greater than that from an equivalent amount of water applied directly to the fire. The highest total concentration of combustibles (CO, CH1, and H2 mixture) obtained during the experiment was about 2 pct; this occurred 6 min after foam reached the fire. This atmosphere was nonex-plosive, but calculations show that if the air flow were reduced to about 5 fpm and if the rate of gas liberation from the fire remained constant, the mixture would be explosive. The use of foam on a fire in all probability would affect the normal ventilation of a mine. If the mine is gassy, this factor must be carefully considered before the foam is applied. APPLICATION OF THE FOAM-PLUG TECHNIQUE IN MINES Equipment and procedures for applying the foam-plug methods must be adapted to the prevailing conditions at a particular mine. Some factors to be considered in developing equipment are: size or extent of the mine, dimensions and number of entries, ventilation system, mining methods, haulage facilities, availability of water, amount of methane liberated, and existing fire-control apparatus. • In most experiments the initial air velocity of 200 fpm decreased to 50 to 100 fpm as the foam plug increased In length.

Jan 1, 1961

By J. G. Richardson, J. W. Graham

The purpose of this paper is to present the results of theoretical and experimental studies of water imbibition. The imbibition processes are involved in recovery of oil from stratified and fractured-matrix formations in natural water drives and water flooding. An understanding of the role of inhibition in implementing the recovery of oil from such formations is deemed essential to proper control of these reservoirs to achieve maximum recovery. The theoretical studies involved development of the differential equations which describe the spontaneous imbibition of water by an oil-saturated rock. The dependence of the rate of water intake by the rock on the permeability, interfacial tension, contact angles, fluid viscosities and fluid saturatiorls is discussed. A few experiments were performed using core samples to determine the effects of core length and presence of a free gas suturation. The role of water imbibition in recovery of oil from a fractured-matrix reservoir by water flooding was investigated by use of a laboratory model. This model was scaled to represent one element of a frac-tured-matrix formation. Water floods were made at various rates with several fracture widths. Interpretations were made of the behavior expected in a system containing many matrix blocks. The presence of a free gas sntu.ration was found to reduce the rate of water imbibition. In the reservoir prototype of the fractured-matrix model, water imbibition rather than direct displacement by water was the dominant mechanism in the recovery of oil at low rates. INTRODUCTION Imbibition may be defined as the spontaneous taking up of a liquid by a porous solid. The spontaneous process of imbibition occurs when the fuid-filled solid is immersed or brought in contact with another fluid which preferentially wets the solid. In the process of wetting and flowing into the solid, the imbibing fluid displaces the non-wetting resident fluid. Common examples of this phenomenon are dry bricks soaking up water and expelling air, a blotter soaking up ink and expelling air and reservoir rock soaking up water and expelling oil. As increasingly better lithological descriptions have been made of the characteristics of petroleum-bearing formations, it has become obvious that imbibition phenomena which were once considered laboratory curiosities are of practical importance. For instance, in reservoirs composed of water-wet sand strata of different permeability in intimate contact, the tendency of water to channel through the more permeable stratum is offset by the tendency for water to imbibe into the tight sand and expel oil into the coarse sand. Also, in fractured-matrix formations the tendency of water to channel through the fractures is offset by water-wet matrix blocks. As some imbibition of the water into the of the largest fields in the world are fractured-matrix reservoirs, it has become increasingly important to understand all the factors involved in the imbibition process. Examples of fractured-matrix reservoirs are the Spraberry field in West Texas which produces from a fractured sandstone', the giant Kirkuk field in Iran', the Dukhan field in Qatar, Persian Gulf2, and the Masjid-I-Sula-main and the Haft-Kel fields in Southwestern Iran, which produce from fissured limestone3. Research into recovery of oil from fractured-matrix formations was stimulated by the rapid decline of oil productivity of wells in the Spraberry formation. One result of this research was the water imbibition process developed by the Atlantic Refining Co.4 Another idea was that much of the Spraberry oil could be recovered by conventional water-flooding procedures5. Subsequently, pilot floods were conducted in this field to test the feasibility of these ideas. It was felt that an understanding of the role played by imbibition processes in displacement of oil from a fractured-matrix reservoir could not be obtained from field data alone because of the many complicating factors and uncertainties involved. Therefore, theoretical and laboratory studies were undertaken to provide this understanding. Study of the equations which describe the linear, countercurrent imbibition process provided an insight into the role of various factors in the process, such as the permeability of rock and inter-facial tension. In addition to the theoretical studies, imbibition experiments were conducted with core samples to determine the effect on the rate of imbibition of such variables as core length and free gas saturation. The principal experimental studies were conducted by water flooding a scaled model of an clement of a frac-tu red-matrix reservoir to evaluate