Search Documents

By Josef Maierl

For the production of advanced high strength steel grades (AHSS) like API X80/X100, dual-phase, martensitic and complex-phase grades a number of hot strip mills need to extend their limits in terms of power and flexibility. Especially for cooling and coiling of these new materials, Primetals Technologies developed the “Power Cooling” and “Power Coiling” technologies. Power Cooling combines the advantages of conventional laminar cooling or “low pressure cooling” with the newly developed “high pressure cooling” with highest cooling rates for flexible operation. The Power Coiler which is needed to coil those high strength grades especially at thicker gauges ensures reliable strip-coiling for a most economical production. To enhance the reliable production of high-strength steel grades for a wide range of strip dimensions, the automation system with its advanced models is an integral part to the mechanical design. In this context the paper presents examples for the installation of power cooling and power coiling in new and modernized HSM.

Aug 16, 2017

By Leandro Rigo Ramos, Marcelo Lucas Pereira Machado, Lumena Gloria de Souza Nunes, Mariana Valinhos Barcelos

The aim of this work was to study the influence of temperature on the grain refining process from severe plastic deformations through the simulation of Accumulative Roll Bonding (ARB) by torsion tests. The assays were performed to simulate the ARB at three different temperatures of 550 ° C, 625 ° C and 700 ° C with 5 torsion cycles with equivalent strain of 0.8 per cycle at a rate of 0.1−1 , totalizing an accumulated deformation of 4.0. Grain refining was obtained with an average size of 2μm, 5μm and 6μm for the temperatures of 550 ° C, 625 ° C and 700 ° C respectively. There was a rise in Vickers hardness by 68%, from 119HV in the annealed sample to 175HV in the deformed sample at 550 ° C. In the deformations at 625 ° C and 700 ° C the value of 130HV E and 150HV respectively was obtained. Based on the obtained results, it can be stated that the severe plastic deformations in microliged steel, carried out at temperatures lower than the end of the austenite-ferrite transformation, produce refined grains of the order of 2μm and, consequently, increase the mechanical strength of the material.

Oct 1, 2019

By John Anthony Vasquez

During the last years Riva Acciaio Verona has taken the decision to invest in the route of a fully automated meltshop. The aim is to reduce at the minimum the operator's intervention from the bucket preparation till the ladle transfer to the continuous casting bay. The foundation for achieving the goal is the introduction of innovative technological solutions (fully automated cranes for bucket charge in the EAF, robots for sampling, etc. The paper underlines how the different solutions are based on the best practices to improve operator's safety and describes the different steps of the project, the different solutions adopted and the results in terms of production, energy savings, cost reduction and improved safety. Details are presented for: scrap yard management and bucket preparation, EAFs centralized controls and related robots for auxiliary operations (sampling, EBT cleaning, scraper for slag door automation, complete mass & energy balance based on process control), LFs centralized controls and process integration.

Aug 16, 2017

By Georg Keintzel

The origin and elimination of 3rd octave mill chatter is a frequently investigated topic since tandem cold mills are in operation. So far only chatter monitoring systems have been successfully deployed, but this implies speed reductions and therefore a significant loss in mill output. Primetals Technologies has developed a new system using active injection of damping in order to eliminate 3rd octave mill chatter. The new hydraulics-based ChatterBlock® Control has now been proven successfully in mill operation. 3rd octave mill chatter, typically occurring in a frequency range between 90 and 150Hz, is a self-excited vibration phenomena typically occurring in the rear stands of tandem cold mills. It can produce significant gauge variations and even cause strip breaks. 3rd octave mill chatter is characterized by a quickly diverging vertical vibration of the rolls for specific rolling conditions (material, mill speed, forces, gauge etc.). Its occurrence requires immediate speed reduction of the mill in order to avoid strip breakage and/or strip quality degradation. This phenomenon thus severely limits mill productivity. The first step to proof the industrial feasibility of the new system was its installation on stand no. 4 of a 5-stand tandem mill. The development process and first results of the industrial implementation will be presented in this paper.

Aug 16, 2017

By Paulo Masiero

Sintered titanium carbide has been extensively used since the early 1980s for demanding wear-resistant applications and, in particular, in environments characterized by high temperature and oxidation. Thanks to its physical characteristics, especially its low density, titanium carbide (TiC) has been successfully applied in the manufacture of cassette guide rollers for hot steel rolling. However, the peculiar characteristics of the sintered Ti carbides make it difficult their redressing and hence this has always represented the limit for a more extensive application. Very often iron based alloys are preferred even if, in general, they are less cost effective just because they are easier to be redressed by turning. The availability of a simple, compact, fully automatic and reasonably priced CNC machine; specialized in the grinding of guide rollers and able to operate accurately and efficiently -both in contour and in plunge- can definitively solve TiC’s redressing problems and render its use even more widespread and attractive.

Oct 30, 2017

By Enif Gutiérrez Guerrero

Inclusion deposition is still a standing problem in the continuous casting of steel since the deposition of alumina inclusions inside the SEN affects the productivity and the product quality. The present work studies the factors involved in the inclusion deposition at the nozzle and the effects of inertial, gravitational, buoyant, pressure gradient, and Saffman forces on the inclusion trajectories. The results show that the inclusions reaching the nozzle, only 30% get deposited along its walls mainly at the Upper Tundish Nozzle (UTN). This area of higher deposition is identified close to a low static pressure and a high turbulent kinetic energy dissipation zones where the effects of the gravitational and buoyant forces do not promote a significant inclusion radial movement since these are aligned with the direction of the flow stream lines. In contrast, in this zone, the Saffman force shows an important effect on the deposited inclusions, slowing down the inclusions in the vertical axis and increasing their radial movement.

Aug 17, 2017

By Márcia Maria da Silva Monteiro Pereira

Tundish is the last reactor where significant metallurgical operations can still be done. Calcium aluminate slags are able to positively contribute to metallurgy considering oxide separation, protection against reoxidation and preclusion of resulphurisation. However, these are poor insulators. When using low melting point slags it is necessary to use another covering material. The deviation from saturation can be used as a measure of absorption capacity. By utilizing computerized construction of ternary and quaternary diagrams it is possible to compare different slags and to find proper slag compositions with reasonable capacity to dissolve inclusions. Objective of the present technical contribution is to evaluate tundish slag capacity to absorb inclusions, considering a particular tundish industrial slag and the changes in its chemical composition during continuous casting of steel. It was observed that slag composition changed during the continuous casting process; this variation is possibly related to interaction between the CaO-Al2O3 liquid slag and the rice hull ash layer which is used above it. Computational thermodynamics was used to determine activity of alumina dissolved in liquid slag; it was observed that the variation in slag composition did not change slag capacity to absorb inclusions, since precipitation of Al2O3 solid phases is not predicted.

Aug 17, 2017

By David Fernando de Carvalho

Este estudo de caso foi solicitado por uma grande mineradora brasileira à Chemtech Engenharia, com o objetivo de avaliar um projeto de um Transportador de Correia de Longa Distância na fase conceitual, onde se buscava a otimização do consumo energético, mínimo investimento financeiro inicial e redução dos custos operacionais. O resultado deste estudo de caso foi usado como diretriz no projeto básico do equipamento, além de ser usado como referência para outros projetos similares.

Sep 25, 2017

By Ângelo José de Santana Tavares Cavalcanti

Este trabalho apresenta o desempenho após a implantação do processo de produção enxuta na operação unitária de filtragem do processo de pelotização das usinas Itabasco e Hispanobrás, com o propósito de aumentar a produtividade, reduzir custos, reduzir paradas de usina e perdas de produção, otimizando as rotinas operacionais e a utilização da mão de obra, bem como a melhoria do ambiente de trabalho. Esse processo é pioneiro em regime de produção contínua.

Aug 1, 2018

By Janete Terezinha Ferreira da Silva Lecheta

A CSN Paraná, sempre trabalhando com a cultura de melhoria contínua, passou recentemente por uma reestruturação na gestão das informações estratégicas, mantendo o que já existia de eficiente e aplicando melhorias e novidades que trouxeram ganhos de produtividade, suporte na tomada de decisão e outros ganhos intangíveis. O breve estudo tem como objetivo apresentar o trabalho que foi feito na CSN Paraná, os conceitos utilizados e metodologias aplicadas para que esse trabalho fosse possível.

Aug 16, 2017

By Thierno FALL

This paper describes the study of the work-roll during the hot rolling process thanks to a 3D model built with the Finite Element Method (FEM). In terms of computational cost, that method needs high resources compared to 1D model which are mostly used. However, the 3D model is built to have a better understanding of the work-roll thermal and mechanical behavior during the hot rolling process. The thermal model shows that the highest temperature reached during rolling are within the range of 500°C and 600°C. The thermal field input used to simulate the mechanical behavior of the work-roll shows a biaxial thermal stress state, in the circumferential and axial planes. However, a peak of radial stress is observed in the backup zone. It did not generate plastic strain but could influence the fatigue behavior of the work-roll.

Oct 1, 2019

By Helênio Resende Silva Júnior

PT. Krakatau-POSCO coke making plant, located in Cilegon, Indonesia, is the results of the know-how and experience of Paul Wurth (PW) in coke making field. The plant has a capacity of 1,321,000 t/y of gross coke achieved by two coke oven batteries with 42 top charging Paul Wurth “Jumbo” ovens each. PW “Jumbo” oven with a useful volume of 78,92 m3 allows decreasing drastically the number of pushing/charging operation per day with a consequent reduction of the diffuse emissions. Gas treatment plant with a capacity of 88000 Nm3/h has been designed in collaboration with DMT GmbH & Co. KG, adopting the latest technologies with specific design know-how. PT. POSCO-Krakatau plant has been successfully commissioned and started-up in October 2013. The present paper will highlight the main technology features applied in PT. Krakatau-POSCO project for both coke oven and gas treatment plants.

Aug 17, 2017

By Andrea Pezza

The steel market is experiencing a difficult conjuncture: on the one hand steel producers minimize their investments while optimizing their over- production, on the other hand suppliers reduce their internal human resources and capacity in order to overcome the instability of the new era. A return to the steel production levels of the past is not expected in the short term. Research, development and plant concept optimization is one recipe to drive the future of the steel business. This article describes a new concept for a VOD plant developed as a result of thorough investigation and assessment of all possible solutions. A joint and tight cooperation with the final customer was necessary to reaching important results. This article consists of the contributions from the plant suppliers in terms of their experience and feedback, as well as the final user’s. The final customer, voestalpine Giesserei Linz GmbH, and the plant supplier, Primetals Technologies, are both worldwide players and highly focused on reaching best quality and innovation.

Oct 30, 2017

By Kurt Herzog

State-of-the-art automation information technology and connectivity enables the digitalization of steel production that goes far beyond conventional automation of industrial production. Initiatives have been started around the globe to foster digitalization like IIoT (Industrial Internet of Things) in the US, Industrie 4.0 in Germany or China 2025. Primetals Technologies is actively driving the digitalization shaping the future of steel production. Intelligent combination of sensor technology combined with digital models as well as quality and production planning and control systems leads to new dimensions in product quality and production cost reduction. New diagnostic ways allow intuitive fault tracing or processing to support faster maintenance. Digital assistants support both operation and maintenance using context-oriented or self-learned information.

Oct 30, 2017

By Luca Tommasi

Danieli complemented its wide range of production plants for the iron and steel industry with a further step upstream into iron ore pelletizing and beneficiation. Danieli has engineered and constructed a state of the art and fully automated pilot plant facility – pot grate and sinter box – at Altos Hornos de Mexico S.A. (AHMSA) Pelletizing Plant, Monclova, Mexico. Installation and commissioning were completed in October 2009. Key features of the pot grate include the avoidance of the need for operator intervention during the test, automatic system preheat, absence of dead time, heat recuperation system with an air/air heat exchanger, oxygen control in preheating and firing with zirconia oxygen analyzer, possibility to test deep beds up to 625 mm. A series of projects have been accomplished by AHMSA availing of the pot grate facility with the aim to enhance pellet plant productivity and to reduce operating costs. The results obtained by use of Danieli pot grate combined with the experience and skill of plant operators has shown significant technical and economical benefits thus fully justifying the initial investment made by AHMSA and confirming the importance of having an in-house testing facility in order to optimize industrial plant operations.

Aug 16, 2017

By Chad Byron Donovan

There is a strong need in North America and other major steel producing markets where major capital investment in new equipment has been minimal over the past several years to make improvements to existing casting machines. In many cases, very cost effective improvements can be made to existing equipment in order to maximize the efficiency and production of an older designed continuous caster, a classic caster. SMS Group and its predecessor companies have been maintaining continuous casting molds for over forty years. This experience has allowed SMS Group to intimately understand the advantages and disadvantages of each design. The most vital component of the continuous caster is the mold copper design, as it has the most influence over the ability to cast a quality product. Updating to a modern copper design is less complicated than most steel producers think and the benefits are significant. Premium mold coatings such as UniGuard® and NanoGuard® allow casters to guard against exposed copper and wear while producing quality products for record campaign lengths.

Aug 16, 2017

By Morgana Cristina Arnold

O Pó de aciaria elétrica (PAE) é um resíduo siderúrgico, produzido pela volatilização de metais pesados durante a fusão da sucata no forno elétrico a arco. Os metais volatilizados, entre eles Zn, Pb, Cd, Ni e Cr, são oxidados e subsequentemente solidificados na forma de um pó fino com partículas de dimensão inferior a 10 micrômetros. Este resíduo é classificado como Classe I – perigoso, segundo a norma NBR 10.004/2004, devido às concentrações de chumbo e cádmio acima do limite estabelecido no ensaio de lixiviação. Neste sentido, uma das alternativas para um possível uso deste resíduo seria a tecnologia de Solidificação/Estabilização (S/S) para a imobilização dos metais tóxicos. O PAE atrasa as reações de hidratação do cimento Portland, o que inviabiliza este cimento na tecnologia de S/S. Portanto, este trabalho tem como objetivo avaliar o efeito do PAE nas características mecânicas e ambientais de argamassas à base de cinzas volantes (CV) e cinzas de casca de arroz (CCA) álcali-ativadas. Foram preparadas argamassas com traço de 1:3 (CV+CCA: areia, 4 granulometrias) e adicionados teores de PAE de 0, 10, 15 e 20% em relação à massa de CV+CCA. Ensaios de resistência à compressão foram realizados nas idades de 7 e 28 dias. Para avaliar a periculosidade do material, análises de lixiviação foram realizadas na idade de 7 dias. Os maiores resultados de resistência à compressão, entre as argamassas contendo o resíduo, foram encontrados para o teor de 20% de PAE.

Aug 16, 2017

By João Lucas Ribeiro e Fernandes, Geraldo Lúcio de Faria, Altair Lúcio de Souza

A ovalização de bobinas é um problema recorrente no processo de fabricação de tiras de aços médio carbono por laminação a quente. Mesmo com o sucesso da etapa de laminação, a ovalização posterior de bobinas pode ocorrer, gerando transtornos à operação e aumento de custos de fabricação. Alguns autores apontam que o fenômeno de ovalização de bobinas pode ocorrer devido a aspectos metalúrgicos, mecânicos e geométricos. Estudos disponíveis na literatura técnica já exploraram as possíveis causas mecânicas e geométricas. Entretanto, existem poucos dados disponíveis que abordem o aspecto metalúrgico, ou seja, o efeito da decomposição tardia da austenita durante, ou mesmo após a etapa de bobinamento. Nesse contexto, este trabalho se propôs a avaliar, por meio da aplicação da técnica de dilatometria, a possível influência das transformações de fases tardias como uma das causas de ovalização em bobinas de um aço do tipo SAE 1050. Ciclos térmicos que simulam, com boa aproximação, algumas possíveis condições de resfriamento acelerado e bobinamento da tira foram aplicados em corpos de prova padronizados em um dilatômetro de têmpera. Diferentes combinações de velocidade de resfriamento e temperaturas de bobinamento foram avaliadas, sendo possível sugerir que uma diminuição na velocidade de resfriamento da tira após a laminação e um pequeno abaixamento na temperatura de bobinamento, em relação aos valores atualmente utilizados na indústria, pode diminuir significativamente a influência da componente metalúrgica na ocorrência da ovalização nesse tipo de aço.

Oct 18, 2019

By Leandro de Almeida

As curvas limite de conformação (CLC) são utilizadas há mais de 50 anos. Propostas inicialmente para o desenvolvimento de produtos provenientes da indústria automobilística, em função das necessidades apresentadas pela indústria de estampagem elas são aplicadas atualmente de maneira geral na produção de inúmeros tipos de peças, oferecendo previsões de possíveis falhas e/ou defeitos durante as etapas do processo de estampagem. As CLC´s permitem prever o afinamento excessivo, enrugamento, estiramento e é claro, a fratura da peça. A raiz da curva limite de conformação (CLC0) é considerada como a mínima deformação obtida pela curva, ou seja, a obtenção de deformações superiores pode levar a peça a falha. As ligas de latão compostas por cobre e zinco, são utilizadas em inúmeras aplicações que necessitam de excelente estampabilidade, como o repuxo profundo, objetivado na fabricação de projéteis. Desta forma, torna-se interessante o entendimento da CLC ou CLC0 para liga de latão em estudo. A obtenção da CLC0 através de ensaios de tração uniaxial no plano da chapa pode ser realizada de acordo com corpos de prova de formatos específicos, como os propostos por Björklund e Nilsson (2014), IRSID (1975) e Wagoner (1980 e 1981). Concluiu-se que o corpo de prova proposto pelo IRSID (1975) é o que melhor se apresentou na determinação das deformações e1 x e2 e com rompimentos dos corpos de prova na região central.

Oct 30, 2017

By Janaina Goncalves Maria Da Silva Machado, Francisco Carlos Gomes da Silva Junior, Stephany Aparecida Santos da Mata, Walney Silva Araújo, Matheus Souza Rodrigues

O aço inoxidável duplex (AID) ASTM 890 de grau 3A tem grande utilização na indústria de tubulações de petróleo no Brasil e no mundo. O estudo da variação do tempo necessário para solubilizar um material é importante, pois, diminuindo esse tempo, pode ser reduzido gastos com forno. O objetivo desse trabalho é comparar diferentes resultados para três tempos distintos de solubilização do aço inoxidável duplex fundido ASTM 890 de grau 3A. A literatura indica que a solubilização desse aço deve ocorrer na temperatura de 1120°C, no período de 4 horas. Entretanto, não existem trabalhos que mostrem a influência da diminuição do tempo do tratamento térmico na resistência á corrosão desse material. A fim de analisar isso, foram feitos trés tratamentos térmicos a 1120°C, em tempos 30 minutos, 2 horas e 4 horas. O grau 3A tem como característica, por exemplo, não conter cobre em sua composição, ter 1%p Mn e ter também 25%p Cr. Para tal estudo foi feito uma análise microestrutural em microscópio ótico para observar diferenças nas fases do material. Em seguida, foi usado ensaios eletroquímicos de monitoramento de potencial de circuito aberto, espectroscopia de impedância e polarização pontenciodinâmica anódica, utilizando um eletrólito de NaCl 1M, para ver o desempenho contra a corrosão nessa liga. Também foi feita uma avaliação mecânica do aço sendo exposto a testes de microdureza. Por fim, foi obtido, com esses resultados, pouca mudança significativa no comportamento do material após diferentes tempos.

Mar 1, 2019