Search Documents

By Lori A. Simpson

Mission Bay is a 300-acre reclaimed site in San Francisco, California, that is currently being redeveloped. Plans include new neighborhoods, parks, a new University of California, San Francisco, research and development campus, a biotechnology campus, and commercial office buildings. New infrastructure is being constructed throughout the site, consisting of utilities, pump stations, and roadways. Previously, Mission Bay was a part of the San Francisco Bay. Reclamation of the shallow bay coincided with the booming development in San Francisco in the 1880s and continued through 1920. Subsurface conditions are extremely variable throughout the site. The stratigraphy generally consists of 5 to 45 feet of fill, up to 140 feet of weak, compressible clay (?Bay Mud?), dense sand, stiff clay, and bedrock of the Franciscan Complex that has been encountered 5 to 210 feet below the ground surface (bgs). Geotechnical issues related to these subsurface conditions include liquefaction, lateral spreading, settlement, and adequate foundation support. This paper presents case studies of the geotechnical aspects of design and construction of several buildings in Mission Bay, highlighting the similarities and variability in the subsurface conditions and the different conclusions and solutions developed for each project. The case studies will include: 1) a building supported on steel H-piles where the depth to bearing varies from about 70 feet bgs in one half of the site to 165 feet bgs in the other half; 2) a building supported on precast, prestressed, concrete piles bearing in a thick, very dense sand layer; 3) a building with over 100 feet of Bay Mud supported on 120- to 180-foot-long PCPS concrete piles driven to bedrock adjacent to buildings supported on steel H-piles driven to bedrock; and 4) sites where auger pressure grouted displacement piles (APGD) and Tubex piles were installed. Case studies will include results of pile driving analyzer (PDA) testing and static pile loads tests, where performed.

Jan 1, 2006

By R. J. Latino

Because of the lack of a universally accepted definition or standard for RCA, we are left to our own conventions in the marketplace as to what is most ?effective? or a ?Best Practice? for our own facilities or organization. This lack of uniformity in the application of RCA produces an equal lack of uniformity in the measureable outcomes of RCA on the bottom-line from site to site and industry to industry. What is the definition of success for an RCA? Is it regulatory compliance? Is it some quantifiable measure of bottom-line performance? Is compliance and bottom-line performance the same thing? Can we measure the ROI we receive by doing compliant RCA? These questions must be adequately addressed if any definition of RCA is to be effective on the bottom-line. Like our various Corporate Vision and Mission Statements, what would be our Vision and Mission for RCA? When pondering the answer to this question, we should consider: ? What Key Performance Indicators will the Success of RCA be Linked to? This provides a direct correlation to the corporate dashboard and therefore garners support for the RCA effort when implemented at the sharp end. Not until we know what KPI?s will effectively measure our maintenance and reliability objectives can we begin to establish which opportunities will afford the greatest returns1. ? What Bottom-Line Metrics will be Tracked to Measure the Effectiveness of Our RCA Effort? Will it be increased production, profitability, regulatory compliance, etc.? Will it be decreased injuries/fatalities, claims, customer complaints, risks, etc.? We should be specific about these metrics and their correlation to the metrics on our corporate dashboard. ? What Will Trigger an RCA Investigation? Normally companies will establish quantifiable thresholds to be surpassed before an RCA will be conducted. Examples may be an OSHA recordable injury, a failure event in which production losses exceed $250,000, an equipment failure in excess of $50,000 or a regulatory violation. This is the norm. However, we should realize this is using our RCA skills totally on a reactive basis. High Reliability Organizations (HRO) strive for proaction and they also use RCA proactively. Why can?t we use RCA to analyze why unacceptable risks from an FMEA are so high? It is perfectly applicable yet rarely implemented in this fashion.

Feb 27, 2013

By James Ransford Dankwah

This work investigates the effect of waste plastics addition on the reduction of iron oxide by sawdust. Composite pellets of iron oxide containing sawdust (SD), high density polyethylene (HDPE) and blends of SD/HDPE were fired under argon in a horizontal tube furnace at temperatures between 1300 and 1500 °C. Reduced samples were weighed after 10 minutes of reduction and the extent of reduction was calculated from the measured oxygen contents of the compact. The results showed improved extent of reduction when SD was blended with HDPE. The highest extent of reduction was achieved at SD:HDPE ratio of 2:3.

Jan 1, 2014

By W. A. Wright

The use and abuse of social media restate common employee relations issues. Business solutions to these issues require advanced preparation. Employers should establish and enforce social media policies to guide their reactions to employees? social media posts that reflect on the employer and its business.

Jan 1, 2011

By Beavis FC, Box JC

The important chemical and fluid flow phenomena in heap, dump and in situ leaching are summarised. Published, quantitative models of these processes are critically reviewed, and their potential applications outlined. Comparison between the independent predictions of one of the models and column leach test data reported by others confirms the potential. Some recent developments by the authors in the fields of fluid flow through unbroken ore and modelling of the more complex chemical systems are briefly Described.

Jan 1, 1981

Amongst the unavoidable studies of the mining engineer who desires to reach the maximum efficiency, is the subject of patents. With the fundamental principles of the patent laws of this and other leading countries he should of course befamiliar, but still more should he keep abreast of that practical knowledge which will enable him to act or advise wisely when the patenting of a new invention, or the sale, purchasing, or adoption of a new patented machine or process becomes amatter for consideration. As every engineer worthy of the name is an inventor and more particularly every mining engineer he has a direct interest in watching the progress of legislation and administration concerning patent monopolies.His worldly prospects may indeed, to a considerable extent, depend upon the defeat of bad patent laws and the removal of incompetent officials, or the appointment of better ones. Better patent administration is always in Australia a valid requirement, and until engineers generally take up and press the demand, bad administration is likely to continue. Even though every engineer is not a patentee, nevertheless his interests in patents must always be direct and powerful, and ignorance or apathy in regard thereto must inevitably injure either his own interests or those of his employer. When we consider the tens of thousands of mines scattered through Australia alone, on everyone of which there is expensivepatented machinery, and when we consider the thousands of...

Jan 1, 1901

By Paikowsky, Samuel G.

"Due to the way drilled deep foundations are being constructed, their structural integrity and geotechnical capacity are highly variable. Drop weight systems are increasingly being used to dynamically test the capacity and integrity of drilled deep foundations. Conventional pile driving hammers are often either inadequate or not economical to test these foundations and drop weight systems have therefore been developed to allow for dynamic testing.The advantages of the tests include high mobility, short testing time, low cost relative to static load tests (allowing multiple tests at a single site), and integrity/construction quality evaluation concurrent with capacity determination. The dynamic testing method for drilled deep foundations encounter several difficulties including: the need for a pre-testing analysis for matching pile, soil and testing system, adequate mass and drop height to reflect the mobilized capacity without structural damage, test interpretations for irregularly shaped and/or non-uniform piles, need for reliable dynamic measurements depending on the impact and the distance between the impact and the measuring point, and limited knowledge about the accuracy of the predictions.The principles of the tests are presented using simplified models and demonstrated via a case history. Drop weight systems are reviewed. Dynamic measurement principles are explained and the construction and testing quality effects are outlined and demonstrated via numerical modeling and case histories. A comparison of dynamic and static tests is presented via a database, case histories and finally a short review of relevant codes is provided.1 IntroductionTraditional static axial load test is performed by a slow application of a force produced against independent reaction, imitating structural loading. It is the most reliable method to determine the pile’s performance as commonly required under typical service conditions. The major limitations of this testing are: (i) high cost associated with set-up, test duration, interpretation and construction delays, and (ii) inability to obtain information about the pile-soil interaction along the pile without additional testing means (e.g. tell tales, strain gauges, etc.). These limitations are acute when high capacity foundations are involved."

Jan 1, 2015

By Jacob Chacko

The east span of the San Francisco-Oakland Bay Bridge (SFOBB), which is one of the most heavily traveled bridges in the world, will be replaced due to seismic safety concerns. The majority of the new bridge will be founded on large-diameter (1.8 to 2.5 meters), approximately 60- to 100-meter-long pile foundations The large-diameter steel pipe piles and soil conditions are similar to those used/encountered in many offshore structures. Thus, the design methods used are based on site-specific modifications to the procedures recommended by the American Petroleum Institute rather than the conventional procedures that have been formulated and used for the design of much smaller piles. Pile foundations will experience their maximum loads during the design earthquake. For the Safety Evaluation Earthquake, tension loads of up to approximately 80 to 90 meganewtons (MN) and compression loads of up to approximately 120 to 140 MN were calculated. Due to the economic importance of the SFOBB and the consequences of catastrophic failure in both economic and human terms, the design and analysis of the pile foundations supporting the bridge consider a number of aspects of pile-soil behavior that are normally ignored. Those aspects include: 1) the effects of consolidation and setup, 2) the behavior under dynamic loading, 3) the losses of resistance under cyclic loading, and 4) the load-settlement behavior of the piles under severe cyclic loading conditions. Since the treatment of complex aspects of pile foundation behavior is not codified in any guiding documents, several project-specific methods were developed for design and analysis of the foundation piles.

Jan 1, 2002

By A. Koski

A pond rehabilitation and environmental education project were proposed by Cleveland-Cliffs Michigan Operations (CCMO) and approved by the Michigan Department of Environmental Quality (MDEQ) and the United States Environmental Protection Agency (USEPA) as partial fulfillment of conditions for a stream mitigation permit. The goals of the project were the rehabilitation of a pond on a tributary of a local trout stream, enhancement of public access and appreciation, and the initiation of a site-based environmental educational curriculum. Cleveland-Cliffs undertook a suite of actions to rehabilitate a pond created by a previous mining operation in 1912 and make accessible to local schools the aquatic and riparian ecosystems. Cleveland-Cliffs partnered with the local governmental unit and two local school districts. The rehabilitated pond and riparian zone provide an accessible natural area that local residents can use for such activities as hiking, biking, walking, fishing and nature study. Vegetative enhancement includes the planting of native shrubs, wildflowers and showy herbaceous plants in the pond, on the riparian fringe and the surrounding area. An interpretive trail was developed around the pond with signs created by a local master watercolor artist. Local schools built and installed picnic tables, benches and a kiosk. Cleveland-Cliffs created pond lesson plans tied to the Michigan Curriculum Framework, developed inexpensive teaching kits and hosted a workshop for teachers from nine local schools. Classes regularly utilize the pond during the school year conducting environmental studies. Nesting boxes, wildflower gardens, bat houses, frog deformity surveys and water quality studies are a few of the activities that classes have conducted at the pond.

Jan 1, 2007

By E. I. Gedgagov, A. V. Tarasov, V. M. Paretsky, A. D. Besser

"Hydrometallurgical technology and equipment have been developed in the Gintsvetmet Institute (Moscow, Russia) for processing of rhenium-containing alloys waste to produce commercial- grade metal products with recovery of all valuable components. The technology is based on waste treatment with hydrofluoric acid with subsequent decomposition with nitric acid at pH = 1 to 1.5 to ensure maximum degree of rhenium conversion to the liquid phase of pulp. Some experimental lots of ammonium rhenate and ammonium molybdate were produced at a pilot plant. The following main techno-economic performance values have been achieved when processing grinding residues (balance-based tests were conducted with a lot of SP-2 alloy waste) to produce ammonium rhenate of high purity, as well as tantalum-niobium, nickel-cobalt and tungsten-molybdenum concentrates: rhenium recovery of 92.3% into a commercial product from grinding waste; production cost of 170-210 US Dollars per 1 kg of rhenium in commercial-grade ammonium perrhenate taking into account its recovery; tantalum and niobium recovery of 75- 77% into bulk concentrate; nickel and cobalt recovery of 88-89% into a mixed concentrate; tungsten and molybdenum recovery of 88% to 91% into concentrate. Introduction During the recent years the use of rhenium has been increasing at a fast pace worldwide [1]. The growing prices for this refractory metal are an essential factor encouraging collection and processing of rhenium-containing wastes. Double-component waste, such as molybdenum- rhenium or tungsten-rhenium alloys can be readily decomposed and the process of rhenium recovery does not cause, therefore, any difficulties. The main separation of metals takes place at the stage of waste digestion with acid, because molybdenum and especially tungsten remain in precipitate in the form of hydrated oxides and rhenium reports in the liquid phase, from which it can be easily extracted by solid ion-exchange or solvent extraction techniques. However, most of rhenium is contained in super-alloy waste [2]. Such waste has different contents of valuable components, such as tantalum, niobium, molybdenum, tungsten, cobalt, nickel, chromium and other metals. The basis of all such super-alloy waste is nickel. Refractory metals in the super- alloy composition are in the form of metallized target-oriented eutectics, and due to this reason hydrometallurgical decomposition of such alloys is a difficult technological task."

Jan 1, 2008

By Geoffrey Hughes

The Narragansett Bay Commission (NBC) is a regional sewer authority that serves ten communities in the Providence, Rhode Island metropolitan area. From 1992 to 1999, the NBC developed a comprehensive facilities plan to abate Combined Sewer Overflow (CSO) pollution in the Upper Narragansett Bay. The plan underwent many major evolutions during this period, most notably the addition of a stakeholder?s process by which NBC demonstrated a site-specific plan to control the pollutants and meet water quality standards. The favored solution consisted of deep tunnel storage with treatment at existing wastewater facilities that had been recently upgraded. In 1999, a final plan was accepted which included two tunnels, five CSO interceptors, twelve sewer separation projects, a wetland facility, and a wastewater treatment facility upgrade. The program is to be constructed over 20 years in three sequential phases (Figure 1). Phase I of the program includes a 4,963 m (16,284 ft) long, 7.9 m (26 ft) diameter, 70.1 m (230 ft) deep storage tunnel; seven drop shafts with connecting adits; ancillary facilities; and a pump station. Construction of Phase I began in 2001 and is expected to be operational by October 2008. This paper focuses on design and construction of the Fields Point Tunnel Pump Station (FPTPS)located at the south end of the main spine tunnel. A189 Ml/day (50 MGD) pump station is required to lift CSO flows from the tunnel to the Fields Point Wastewater Treatment Facility (FPWWTF). The pumps are to be housed in a 35.6 m × 18.6 m ×20.7 m (117 ft × 61 ft × 68 ft), 91.4 m (300 ft) deep cavern excavated in a complex meta-sedimentary rock of the Rhode Island Formation, and connected to the surface by 9.7 m (32 ft) and 3.4 m (11 ft) diameter shafts. Factors which influenced selection of the size, configuration and location of facilities included the preferred arrangement of pumps, critical aspects of site geology, and estimated cost. Technical and value engineering reviews also affected the final design. Following Notice to Proceed (NTP), concerns were raised by the contractor regarding constructability and design. Additional geotechnical investigation and independent engineering review were employed to validate the design assumptions. The cavern was successfully excavated and sup-ported in rock, completed on schedule and within budget in 2005. In 1992 the NBC retained Louis Berger Group (LBG) as Program Manager (PM) for the CSO Abatement Program. LBG thereafter formed a design team including: Jacobs Engineering Group(JEG) as the designer for underground structures and near surface collection facilities; Black and Veatch(B&V) to design the pumping system and associated facilities; Haley and Aldrich (H&A) to oversee the geotechnical program; and Malcolm Pirnie to design the system-wide instrumentation and control system. Construction management, resident engineering, and inspection services were provided by the joint venture Gilbane/Jacobs Associates (G/J).

Jan 1, 2008

By Milton Fies

Introduction The first experiment in underground gasification of coal in the United States was conducted at Gorgas, Walker county, Alabama, under a co-operative arrangement between the U.S. Bureau of Mines and the Alabama Power Company, at the suggestion of the Power Company. The test was conducted on property of the Alabama Power Company, that owns some 19,000 acres of coal-bearing lands on which there is developed a highly mechanized mine producing some 2,500 cons of good quality steam coal per day. At the same locality ?there is a 200,000 kilowatt steam plant one of the largest in the southern portion of the United States. The Alabama Power Company owes much of its beginning in 1912 to British vision and courage. The original plans for building hydroelectric plants in Alabama, and for the construction of necessary transmission lines, were submitted to Sperling & Company, bankers of London, who agreed to underwrite certain bond issues, the proceeds of which would be used in launching the new Company on its programme. The set-up by which these funds from England were received was through an intermediary Canadian company, which the English investors desired. The Canadian company - Alabama Traction, Light and Power Company, Ltd. became owner of the securities of the Alabama Power Company and marketed its own securities through the banking house of Sperling & Company. Without assistance at this time the Alabama Power Company could not have gone ahead with its programme of expansion and the bringing together of the properties necessary for laying the foundation for a strong Company, fortified with ample power resources essential for future requirements and for dependable service to the public.

Jan 1, 1948

By Silas C. Nichols

"Abstract Piling and deep foundations are a staple for transportation projects in the United States (US). Driven or bored piles have been used for everything from support of bridge foundations and retaining structures to support of culverts and embankments on soft ground. Deep foundations have been popular in the US transportation market to better handle large axial and lateral loads, extreme event loading, and to better control structure movement. However, there are challenges in the maintenance of design and construction codes in transportation for consistent and reliable structure foundation elements. A significant amount of effort continues in the US to maintain national codes and specifications at a level consistent with the state of practice, and identify and conduct research for providing safe and cost effective highway structures.IntroductionThe transportation sector in the United States has a hierarchy of design and construction codes that are used for the specification of piling and deep foundations. Any highway or bridge project on the National Highway System (NHS) must be designed and constructed in accordance with a national set of standards approved by the State Highway Departments, and that are acceptable to the Federal Highway Administration (FHWA). However, in any jurisdiction, exceptions are permitted with approval. Therefore, design may be governed by the national standard specification, a state standard specification and design manuals, special provisions, or guideline specifications. Any of these standards, or a combination, may be used depending on the needs of the owner agency.The FHWA and the American Association of Highway and Transportation Officials (AASHTO) have worked together in the development and maintenance of geotechnical design and construction guidance and codes that support the surface transportation community. General geotechnical engineering practice in the United States lacks a singular, national design and construction code that addresses all aspects of geotechnical engineering. As a result, the AASHTO specifications provide the most complete geotechnical specifications focusing on structure foundations, retaining walls, and buried structures for surface transportation applications. This includes piling and deep foundation types commonly used for support of bridges and transportation structures.The FHWA National Geotechnical Team has published several technical guidance documents that include guideline specifications for the design and construction of driven and bored deep foundations. Reference documents published by FHWA summarize the state of practice and provide recommended design and construction guidance. These reference documents have long served as a basis for provisions included in the AASHTO specifications. Maintenance of the design code and specification, and related guidance documents for consistent use on US transportation projects requires a collaborative effort between industry, FHWA, and the member state highway departments that make up AASHTO."

Jan 1, 2014

By R. Ressel

Keywords: ferrovanadium, thermodynamics, phosphorus Recyclable material is rapidly gaining in importance as a source of raw materials in industrialized countries. This is also the case in the production of ferrovanadium, where, increasingly, materials such as discarded capacitors, spent catalysts, slag, dust and sludge are used. As the V-content in the raw material varies greatly, the demands on process technology are very high. The share of perturbing elements depends very much on the source of the raw materials, which, in turn, makes a corresponding optimization of the various refining steps necessary. The raw materials are mostly available as oxides, which means that carbon, silicon or aluminium are used as reducing agents. Thermodynamic calculations were used to show especially the behavior of vanadium and phosphorus at different process conditions.

Jan 1, 2005

Ledcap Pty Ltd has developed two software tools for assisting in the determination of life-of-mine (LOM) trucking requirements. The first tool generates haul paths and the second calculates truck travel time over these paths. The two step approach allows the paths to be viewed and if required edited, to better represent the actual site haul routes.The first tool automatically creates haul paths between the mine bench and the dump. To do this the user supplies a master haul route and a scheduled block model. The master haul path and the block model are interacted to create multiple haul routes, one for each pit/dump bench pair in each scheduling period. Each path carries with it a record of the scheduling period it represents and the dry tonnage hauled over the path in that period.The second tool calculates truck travel time over the path. Data from the manufacturer's rimpull and retarder curves are used to calculate accelerations and speed over each segment of the haul path. As the paths are derived from digitised representations of mine haul routes the path f les often have over a hundred segments. This detailed representation of the haul route allows the software to automatically adjust speed for different radius corners and accurately simulates the changing accelerations over the gradient changes that occur in real life mine ramps. Rolling resistance can be specified at a global level, at a segment level and at a period level. This allows rolling resistance to be changed seasonally as well as spatially.Life-of-mine trucking studies attempt to calculate an accurate answer from extremely variable inputs. This paper will detail the features of the two software tools and how the tools provided in the software can assist the mine planner to have greater confidence in their life-of-mine trucking requirements and the subsequent production capacity inputs to their scheduling calculations.

Dec 6, 2010

By D. J. Steynfaard

Sishen Iron Ore Mine is situated 280 km north-west of Kimberley in the Northern Cape Province of South Africa. The mine produces and sells high quality iron ore of various specifications to various national and international clients. The saleable product is derived from the blending and beneficiation of different types and qualities of hematite iron ore. This paper documents the new developments which were implemented (or are in the process of being implemented) on the mine in the long-term planning, medium-term planning, grade control and material tracking in the beneficiation plant with special attention being paid to the quality of the final, saleable product. The process starts with the long-term planning where the pit shell and pit optimization is determined by Whittle 4X. New developments include the introduction of a linear programming based scheduling system to enhance the long-term schedule generated by Whittle 4X. The LP route was decided on in order to take into account all the constraining factors of the final product that could not be configured in Whittle. To complement this the XPAC Auto Scheduler scheduling package was introduced to do the medium-term mine scheduling. This 18-month rolling plan includes cost parameters to enable the planner to extract a detailed operational budget from the scheduling while ensuring that production standards are maintained and grade constraints are met. The existing grade control system was enhanced with GPS capabilities and a computer system to do material tracking. The high precision GPS system introduced on the shovels allows for the accurate control of the loading procedures at the mining face. Because of the complicated geology and grade composition of blasting blocks it is imperative to accurately differentiate between different materials in the same blasting block and being able to excavate that with the loading equipment. The GPS system on the trucks allows for accurate location monitoring of dumping in order to keep track of specific material types. The state-of-the-art material tracking system developed for Sishen will enable the grade control officer to keep track and record various parameters of the material from its in situ position in the blasting blocks, through the crusher and onto different stockpiles, in various stages of the beneficiation process and onto the blending beds, into the dispatching trains and eventually into the ships for international distribution. These developments elevate the Sishen planning and grade control systems to a new level of service excellence from which management can obtain accurate and timely information on product status. It also enables Sishen to maximize resource utilization while still complying with the tough market constraints.

Jan 1, 2003

By Lee Sieng Kai

This paper presents the result of the analysis of strain-dependent concrete modulus from full-scale static axial compression load tests conducted on more than 200 instrumented cast-in-place barrettes and bored piles over the past 12 years, covering commonly adopted grades of concrete for heavy foundation construction in Malaysia and Singapore. The concrete modulus values, Ec, analysed were directly back-calculated from the material of the instrumented test piles by means of placing a layer of vibrating wire strain gauges near the pile head region. The best fit curve for back-calculated concrete secant modulus versus measured axial strain follows non-linear behaviour for both categories of test pile samples analysed. The result of the analysis seems to suggest that using average constant modulus value would generally lead to a significant error in load distribution computation, particularly at high stresses region.

Jan 1, 2006

By Mahiyar Nasarwanji, Jonathan K. Hrica, Jonisha P. Pollard, Lydia M. Kocher, Brianna M. Eiter

Within the metal/nonmetal mining sector, fall-related incidents account for a large proportion of fatal and non-fatal injuries. However, the events and contributing factors leading up to these incidents have not been fully investigated. To help provide a clearer picture of these factors, an analysis of imminent danger orders issued by the Mine Safety and Health Administration (MSHA) between 2010 and 2017 at both surface and underground metal/nonmetal mine sites revealed that most orders are associated with fall risks. Of these cases, 84% involved the workers not using fall protection, fall protection not being provided, or the improper use of fall protection. Fall risks for workers most frequently occurred when standing on mobile equipment, performing maintenance and repairs on plant equipment, or working near highwalls. In most cases, a single, basic, corrective action (e.g., using fall protection) would have allowed workers to perform the task safely. Overall, these findings suggest that a systematic approach is needed to identify, eliminate, and prevent imminent danger situations. Furthermore, to protect mineworkers from falls from height, frequently performed tasks requiring fall protection should be redesigned to eliminate the reliance on personal fall protection.

By Jerry Pyatt

Lead has been used by mankind since before the Egyptian pyramids were built. Its durability provides for a continuum of innovation. As the largest integrated lead producer in the Western Hemisphere, The Doe Run Co. is committed to locating, mining, processing and sup-plying lead in ways that are responsible and sustainable. It takes ingenuity and resolve to successfully operate in the heavy industry field today. Doe Run is committed to applying responsibility through sustainability, lean manufacturing, safety, environmental stewardship, education and workforce development, and com-munity support.

Jan 1, 2008

The Calypso geothermal field, mapped by the R V Sonne (cruise SO-135) in 1998, includes four main sites, the Northern Vent Area (centred on 37¦ 36.7'S, 177¦ 06.2'E, area 1.5 km2), Central Vent Area (37¦ 39.4'S, 177¦ 05.2'E, 1 km2), Southern Vent Area (37¦ 41.7'S, 177¦ 06.0'E, 1 km2) and Mercury Vent Area (37¦ 41.3'S, 177¦ 07.3 'E, 0.5 km2). Hydrothermal activity at the vent sites is controlled by minor, sub-parallel NE-trending normal faults. Gas bubble trails (C02) and shimmering hot water vent from fractures and joints between large blocks of silicified volcaniclastics and in depressions in the sediments at the base of these outcrops. Measured maximum vent temperatures are between 180¦C and 201¦C. Venting fluids are at, or just below, boiling for water depths of 200 m. Rock samples recovered by dredge from the sites include massive anhydrite, clay-altered pumiceous ash, silicified volcaniclastic sediments and volcaniclastic breccias cemented by sulphur. Clay-altered samples, dominated by randomly interstratified illite-smectite and accessory chlorite, indicate formation environments of 70¦C to 90 ¦C. Native sulphur is abundant throughout the samples. Fine-grained (<1 mm) disseminated pyrite and vein pyrite occurs in the clay-altered pumiceous volcaniclastics and argillites. In the Southern and Mercury Vent Areas, fine-grained orpiment, realgar and cinnabar have deposited in the sandy matrix of volcaniclastic breccias. Amongst the cinnabar, small (<2 mm) beads of native Hg formed on the surface of several rocks following their recovery. These samples also contained abundant light hydrocarbons, which coat the rocks with an oily sheen.

Jan 1, 1999