Search Documents

THE flotation plant at Mount Lyell was erected, primarily, for the treatment of ore from the Lyell Comstock mine. These workings are situated over a mile in a direct line north of the North Mount Lyell mine, and are connected with the Reduction Work at Queenstown by a 2-ft. gauge steel tramway via the Queen River valley a distance of 7 miles. The property was purchased from the Mount Lyell Comstock Copper Co. After the disastrous fire in the North Mount Lyell mine in October, 1912, steps were immediately taken to make Lyell Comstock ore available for treatment, in order to relieve distress caused by any prolonged stoppage of work, and subsequently 13,032 tons of ore, averaging 3.38 %copper, 0.28 oz. silver, and 0.034 oz. gold; were smelted. When operations were resumed at the North Mount Lyell mine, it was evident that there was no economic advantage in smelting Lyell Comstock ore as compared with the higher value North Mount Lyell ore, which was also a better flux for the Mount Lyell pyrites, and that the future of the Lyell Comstock ore depended upon cheap mining and successful concentration of the ore. Therefore, extensive trenching and diamond-drilling was carried out, and a sufficiently large quantity of ore proved available for cheap extraction by open-cut methods. At the same time bulk tests by flotation were carried out at the Minerals Separation testing plant in Melbourne on different classes of ore from the Mount Lyell Comstock mine proper, followed by laboratory tests at Queenstown on all classes of ore available. All these tests demonstrated that the ore was amenable to the process, provided that it was ground finely enough. Plant erection was delayed by the general dislocation of business at the outbreak of war, but finally it became...

Jan 1, 1920

By Walter I. Paniagua

Drilled shafts and precast concrete piles were installed for the foundation of several structures in a reconfiguration project of a refinery in Minatitlan, Veracruz, in the Gulf of Mexico. The soils are alluvial deposits of flat land from the Coatzacoalcos River, which are embedded with layers of sand, soft clay, and peat. As part of a QC/QA program, load tests, both static and dynamic, axial and lateral, were performed. In this paper results of 32 axial tests are presented, in which typical load-displacement curves were measured at the top of the foundation elements; from the interpretation of these plots, data were recorded for ultimate side shear and in some cases for end bearing capacities, which are compared with the theoretical results of the final stage of the foundation design. The comparison shows that under allowable loads, side shear determines the bearing capacity of piles, even when the tip is embedded in a hard layer. Underestimation of the side shear is evident; therefore design criteria, as well as the methods used for obtaining soil parameters, should be reviewed.

Jan 1, 2007

Longwall minim; is a highly mechanized, high productivity mining method that is finding increasing applications in coal. Although the method would be highly advantageous in certain hard rock mining applications it cannot be applied in hard rock because no suitable cutterhead exists for such materials. The wedge longwall cutterhead is a, roller cutter device that is wedge-shaped, with cutters arranged to eliminate the very large normal force ordinarily required to cause such cutters to penetrate hard rock. However, the wedge geometry cannot be extended to a point: special nose cutters are needed to open a narrow slot for the wedge. This report describes the design, fabrication, and successful field testing of these critical nose cutters.

Jan 1, 1974

By A. W. Khair

This paper deals with the design characteristics of cutting tools and the operating parameters these tools are usually subjected to. Eight types of cutting tools/bits with different geometrical shapes and sizes were tested in a linear cutting apparatus, utilizing concrete blocks. The objectives of these experiments were to study the performance of each type of bit, make qualitative assessment of each bit geometry and size and establish cutting parameters for efficient utilization of the tools. During the experiment required forces Fx, Fy, and Fz, cutting, penetrating and lateral forces respectively and audible and sub-audible noises were measured. In these experiments, the depth of cut was kept constant to 1.5 inch while the bit spacing was varied 1.5,2.25 and 3.0 inch (3.75,5.6 and 7.5cm respectively). The results of these experiments indicated that by optimum ratio of depth of cut to bit spacing, the cutting face will be cleaned with the least ridge/land remains between the bit groves, resulting in least specific energy consumption, more large and less fine product particles and substantial reduction of audible noise. The results of these experiments also showed that proper bit design not only decreased cutting energy consumption but also reduced audible noise.

Jan 1, 2001

By R. W. Smith

Many industries such as the cement industry handle large quantities of limestone and clay slurries. However, at present very little is known about the flow properties, such as friction loss due to flow of slurries in pipelines. This lack of knowledge has made it often very difficult to calculate the total dynamic head of a proposed slurry handling system, and therefore has often made the selection of correct size slurry handling equipment difficult. Because of lack of knowledge about slurry flow a study of slurry flow theory has been made at the Portland Cement Association's Research and Development Laboratory with the idea of developing a method whereby friction losses due to slurry flow may be predicted for any size pipeline. The flow equations developed have been checked by pilot plant size equipment. DERIVATION OF FLOW EQUATIONS It has been known for some time that limestone and clay slurries handled in cement plants do not flow in the same manner as a Newtonian fluid such as water. When a Newtonian fluid flows the shear stress at any flow velocity is proportional to the rate of shear. This phenomenon can be illustrated by a line (Figure 1). The viscosity of the fluid is the slope of the curve. Thus, the flow properties of the material may be characterized by a single materials constant: viscosity. When a non-Newtonian fluid with the type of characteristics exhibited by limestone and clay slurr-ries flow, a similar curve can be constructed (Figure 2). This graph is a shear diagram of a Bingham plastic non-Newtonian fluid. It should be noted that with the Bingham(1) plastic type of flow viscosity, the slope of the curve, is still an important materials constant. In addition, however, there is another materials constant, namely the yield stress of the material. One way to visualize this constant is to consider it as the amount of energy that must be put into a Bingham plastic material to start it flowing.

Jan 1, 1961

By H. R. Hanley

The characteristics of alloyed anodes and their influence on the products of electrolysis and power consumption have been noted previosly ously in the literature.' This paper presents data in continuation of the subject given in an earlier paper by the authors.2 As noted in the authors1 previous paper, the objectives of this work are the reduction in the cell voltage and the purity of the cathode product resulting from the use of alloyed lead anodes. The fundamental facts developed in the previous paper were: (I) that the presence of a small amount of calcium lowers the anode potential approximately 50 per cent. below that of pure lead; and (2) that thallium when present to the extent of 4 per cent. rendered the anode practically stable, thereby lowering the contamination of the cathode by lead to a very insignificant amount. The specific features determined in this recent work are as follows: 1. The lowest limit of calcium in the lead which will still give maximum lowering of the anode potential. 2. The characteristics of the thallium-calcium-lead anode. 3. The characteristics of the silver-calcium-lead anode. 4. The characteristics of the thallium-silver-calciurn-lead anode. It was determined that 0.1 per cent. calcium in the anode was sufficient to lower the anode potential approximately 50 per cent. Table 1 shows the characteristics of alloyed anodes tested. The anode composed of 0.1 per cent. calcium, 4 per cent. thallium, and 95.9 per cent. * Professor of Metsllurgy, Missouri School of Mines. t Professor of Metallurgy and Ore Dressing, Hea.d of Department, Missouri School of Mines. Assistant Professor of Metallurgy, Missouri School of Mines. 1 Among others, see C. G. Fink and Li Chi Pan: Insoluble .Anodes for the Electrol-ysis of Brine [Trans. Amer. Electrochem. Soc., (1926) 49, 83-1341 and other papers by these authors. U. CJ. Taintori, 8. G. Taylor arid H. P. Ehrlinger: Lead Alloys for Anodes in Electrolytic Production of Zinc of High Purity. Truns. A. I. M. E. (1929) 192-200. 2 H. R. Hanley, C. Y. Clayton, D. F. Walsh: Investigation of Anodes for Production of Electrolytic Zinc. Trans. A. I. M. E. (1930) 275

Jan 1, 1931

By Germán Rodolfo Ocampo Castillo

El presente texto señala la incrementación de la productividad de la mina Xstrata Tintaya -Antapaccay a través del contrato de personal adicional, donde se reemplace a los operadores titulares durante la hora de refrigerio y asi mantener una operación contínua en la mina. Como consecuencia de ello, se incrementará la cantidad del mineral descubierto en la mina y por ende, el costo unitario de las libras de cobre adicional por operación contínua se reduce.

Sep 12, 2011

By Jean R. Garcia, Paulo J. R. Albuquerque, Renato P. Cunha, Osvaldo Freitas Neto

"Abstract Results obtained from in-situ load tests carried out on drilled displacement piles sunk in a porous, lateritic and unsaturated soil deposit, are analyzed in this paper. Three slow-maintained load tests were performed on deep instrumented piles with a diameter of 0.37 m and around 12 m long. The soil deposit consists of a superficial, silty clay “porous” layer 6 m thick, with an average standard penetration blow count (NSPT) of 4 and cone tip resistance and sleeve friction (qc and fs) of 1.5 MPa and 48 kPa, respectively. Under this layer there is a residual stratum 10 m thick, geotechnically consisting of a “porous” clayey silt with an average NSPT of 7 and qc and fs of 2.4 MPa and 202 kPa, respectively. The water table was reached at a depth of 17 m below ground level. The results of the field load tests yielded a maximum pile load (average for the tests) of 1428 kN, which is twice as high as corresponding experimental values from standard bored piles with similar geometric conditions. Exhumation of one of the tested piles was carried out after the test, in order to check integrity and shaft conditions. Numerical finite element analyses, using the commercially available French Code LCPC Cesar®, were performed in order to back-analyze the geotechnical soil parameters for a post execution pile condition. The results permitted a better understanding of the improvement of the subsoil given the intrinsic execution characteristics of this particular pile. It was also possible to note that drilled displacement piles have great potential to become an economically viable solution in tropical soils, given the enhanced behavior of such piles when compared to alternative (cheaper) techniques. In fact, it has several advantages which should make it a key foundation type in the Brazilian market in the future.IntroductionMost buildings in tropical soils use, as the main type of foundation, deep bored or auger type piles. These types of foundations can be performed in various ways, for example with or without soil extraction, with or without bentonite mud and so on. Two main processes maybe formulated: the first execution process is typified by bored pile types, continuous flight auger piles etc., which do not cause excessive soil displacement during excavation. With respect to the second process, one could mention, amongst others, driven piles (precast concrete or steel), Franki piles and drilled displacement piles, which do displace the soil during excavation by pushing the soil laterally around the hole in order to allow either the penetration of the pile or the excavator auger."

Jan 1, 2014

By Chulgi Suk, Hoon Park, Hyonsoo Kim, Hakman Kim, Sangho Cho

Dust emission from blast demolition and other construction activities can be a nuisance; it is widely recognized that fine particles less than 10 µm in equivalent diameter (called PM10) may cause health problems. Mist spray systems, such as rain guns, sprinklers, water/surfactant sprays (or foams) etc., are some of the most effective dust suppression methods. A large amount of research has showed that when water droplets are produced in an equal amount to that of dust particles, the airborne dust is suppressed by the agglomeration of dust and mist particles. A method for generating micro-sized mist from water, achieved by the detonation of explosives in the water tube, was suggested and is called the ‘detonationdriven water bag burst system’. There are many experimentally observed limitations of the explosioninduced water break-up process. The water bag explosion tests were simulated using the AUTODYN software, in order to investigate the aerosolization mechanisms of the detonation-driven water and water break-up process into micron-sized droplets. As a result of the numerical analyses, the diffusion direction of water when detonating in the central interior part of water tube was radioactive and significantly stronger than when detonating in the bottom exterior part; this is due to the compressive flow of the volume change inside of the water tube, which resulted from the blasting wave inside of the tube, as well as the reflected pressure on the ground. Blast tests of full-scaled reinforced concrete columns were conducted to verify the effectiveness of the suggested detonation-driven water bag burst system. The water breakdown and dispersion that occurred while blasting the reinforced concrete columns were observed using a high-speed camera, and dust generation was monitored using four density detectors. The suggested detonation-driven water bag burst system showed that the average dust density decreased by up to 7 mg/m3.

Jan 1, 2016

By I. W. Farmer

High horizontal stresses and high horizontal to vertical in-situ principal stress ratios in the plane of underground drifts and entries can damage weakly laminated roof rocks quite severely. Such stresses are difficult to measure accurately, as illustrated by case histories of in-situ stress measurement at Wistow and Lea Hall mines, in the UK. Their direction and relative magnitude can, however, be estimated from the absolute velocity vectors of continental plates. With the preliminary results from the World Stress Map project now available it is possible to indicate mining areas where regional horizontal stresses are low, such as Europe, and high, such as Australia and Asia

Jun 19, 1905

By A R. Heath, I Arbuthnot

Feed slurries are typically flocculated in a thickenerÆs feedwell to increase the settling rate, underflow density and overflow clarity. High molecular weight polymeric flocculants are normally used, but present a number of challenges in terms of make up, dilution, delivery and mixing with the feed slurry.Various aspects of the flocculant dilution and delivery system have been studied with a combination of flow visualisation and computational fluid dynamics (CFD). An open topped flocculant dilution/mixing box has been developed to replace a conventional flocculant manifold, with improvements to the mixing, fault diagnosis and ease of determining the flow split to the various dosing points. The addition points to the feedwell have also been studied, both in terms of where the flocculant is added, and how. While conventional multi-hole spargers are effective in dispersing flocculant, they are prone to blocking and have been replaced by open-ended pipes. The required dispersion is provided by an efficient mixing element placed in the dilution port. Adding the flocculant into the feedwell dilution stream prior to mixing with the slurry also provides super-dilution of the flocculant that can further improve the flocculation process and reduce flocculant consumption.CITATION:Heath, A R and Arbuthnot, I, 2013. Advances in thickener flocculant delivery, in Proceedings MetPlant 2013 , pp 86-92 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

By David Hake, David Salisbury

The Drainage Services Department (DSD) of the Hong Kong SAR Government commissioned the design and construction of the West Kowloon Drainage Improvement, Stage 2, Phase 2, Kai Tak Transfer Scheme (KTTS) project in 2000 to relieve potential flooding in Mong Kok caused by the insufficient capacity of the existing storm water drainage system. The KTTS involves construction of a 1.5km,4.4m drainage tunnel and a 450m long box culvert, running from Waterloo Road near Hereford Road to the existing Kai Tak Nullah in San Po Kong. This paper describes the design and construction of; the bored tunnel through both hard rock and soft ground using a slurry Tunnel Boring Machine (TBM), six associated access shafts, a connection structure at Waterloo Road and the box culvert connecting the bored tunnel to the outfall at Kai Tak nullah. Details will be provided on the contractor’s alternative designs adopted during the contract including the use of fibre reinforced shotcrete as one-pass temporary and permanent support for three of the shafts and modifications to the Engineer’s design for the box culvert structure.

Jan 1, 2005

By M. Mikolás, L. Pomothy, K. Špakovská, M. Vanek

"Enterprises are faced with increasing economic competition and managers are obliged to look for methods that will ensure a competitive edge in their companies’ markets. These methods include managerial concepts that employ common sense and are low cost. One of these approaches is the KAIZEN methodology, of Japanese origin; kaizen means continuous improvement (CI) when translated. A mining company, despite some of its idiosyncrasies, is just an enterprise where the application of KAIZEN can be advantageous. The company investigated, OKD, is the only domestic producer of hard coal in the Czech Republic and operates four mines that produce 11 Mt of coal annually. The OKD management team opted for KAIZEN as their principal method of continuous quality improvement. This paper suggests ideas for development and application of processes that provide for continuing improvement of production and management. The authors have taken the OKD Company to be their benchmark in the field of mining activities. The paper also focuses on possible difficulties accompanying the introduction of CI sustainable methods. Three years of application of CI methods has increased the income of the company by almost US$38.1 million, which provides a strong argument for continued application."

Jan 1, 2015

By Michael Alber

Coal mining by the longwall method typically causes seismic events. This paper describes the research on mining induced seismicity around two specific longwalls at 1100m depth under several old longwalls. A local network featuring 21 geophones has been installed, underground core drilling and an extensive rock testing program were executed. A rock mechanical model featuring a multi-layer strata was created for use with numerical analyses. Seismic events were localized and three different event types are described. Focal analyses yielded distinct modes of failure. Those types are explained by different failure mechanisms, namely fault activation, remnant pillar punching and beam failure. The use of rock mass classification, rock mass strength criteria and in situ stresses together with 2D and 3D numerical analyses allows evaluating the findings from seismology approaches. Conclusions are drawn that the orientation of longwall with respect to the major horizontal stress orientation plays an important role in mine induced seismicity.

Jan 1, 2008

By L A. Maslov

We have considered the following characteristics of the crust and upper mantle of the Pacific Belt: seismic wave velocity anomalies, mechanical stress and shear deformation rate fields, heat flow and the pattern of metallogenic provinces of the Belt. It has been noted that there exist certain .regularities in distribution of the above mentioned geophysical characteristics and metallogenic zones within the Belt, displayed by prevalence of the lithophile elements in the Asia-Australian part of the Belt, and of the chalcophile ones within the American part.

Jan 1, 1995

By D Craw, K A. Hunter

Deposits of the metalloids arsenic and antimony occur in quartz veins of mesothermal hydrothermalsystems in the South Island as arsenopyrite (AsFeS) and stibnite (Sb2S3). Arsenopyrite and stibnite occur in natural exposures in gold-mining areas, and additional arsenopyrite and stibnite have been exposed to the atmosphere by mining activity. At present the drinking water limits for dissolved As and Sb are 10 ppb and 3 ppb respectively. Sampling and analysis techniques are critical to determination of metalloid concentrations at these low levels. Endeavour Inlet in the Marlborough Sounds is an historic mining area (late 19th Century) with elevated As and Sb in waters emanating from mineralised rocks. Waters running out of abandoned adits have concentrations of As and/or Sb up to ppm levels. Natural waters have high Sb and low As, and the As levels increase markedly where anthropogenic activity has exposed rock. Changes in Sb/As ratio could potentially be used to quantify the anthropogenic component of metalloid mobility on mine sites on the 100-year time scale.

Jan 1, 2002

By R. J. Visintainer, W. L. Whitlock

"Difficulties with the sizing and operation of centrifugal froth pumps are common and the underlying fluid dynamics are complex. Design and selection often relies on previous experience, offering unreliable guidance for novel applications or unexpected problems. The current paper describes a program of extensive laboratory testing on froth handling centrifugal pumps, covering a range of flows, heads, speeds, viscosity, air content and froth stability. Variations in impeller vane design and the effectiveness of an airlock venting apparatus were also examined. The program resulted in a better understanding of centrifugal froth pump dynamics and insight for the troubleshooting of field applications.INTRODUCTION The Challenge of Pumping Froth In pumping mineral processing froth, the handling of large quantities of air within the fluid is often unavoidable. Efforts to reduce the amount of air present at the pump suction, while always recommended for improving pump performance, may have limitations. Some strategies may also carry an economic penalty, such as unwanted process dilution (e.g. due to water spray or injection), or increased capital cost of equipment due to oversized pumps, sumps and/or piping. Froth pumping losses fall into several categories, as described below and represented graphically in Figure 1. • Density effects: Entrained air reduces the pressure created by the centrifugal pump in direct proportion to the reduction in bulk density. This is not a true “loss”, since the head produced by the pump (in meters of froth), may remain unaffected. However, the reduction in pressure often leads to a corresponding increase in pump speed required to drive the system, which itself leads to increased NPSH required by the pump (NPSHR). Furthermore, by adding a gas phase, the overall volumetric flowrate is increased, assuming a fixed quantity of de-aerated liquid being handled. This leads to increased suction velocity which further reduces the NPSH margin by simultaneously increasing pump NPSHR and decreasing system NPSH available at the pump suction (NPSHA). • Viscosity effects: Increased viscosity introduces an additional factor in some froth pumping applications, such as oil sands bitumen froth. Losses result from increased shear stress within the fluid flow, which increase with flowrate. Viscosity also facilitates the formation of airlock by reducing turbulence and allowing individual bubbles to coalesce more easily within the flow stream. Finally, it increases pump NPSHR by increasing local pressure drop in the vicinity of the vane inlet edges. • Airlock effects: Also known as air binding, it occurs when air or gas coalesces within the pump suction or impeller passages and begins to collect there, held by buoyancy forces within the rotating flow field. In essence, the liquid “floats upwards” towards the pump suction against the outward directed centrifugal forces. The airlock acts as a blockage, with corresponding reductions in flow, head and efficiency. NPSHR also increases, due to increased velocity and distorted streamlines in the flow circumventing the blockage."

Jan 1, 2012

By J. M. Uys, T. B. King

WalSH, Chipman, King, and rant' have measured the water content (as hydrogen) of actual steel-making slags. An average water content of 290 ppm was found for basic open-hearth tapping slags and 114 ppm for acid open-hearth slags. Upon equilibration of these slags at 1550°C with a 25 pct H20-75 pct Nz atmosphere, the water content increased to about 410 and 300 ppm for the basic and acid slags, respectively. Walsh et al. concluded that an acid slag was thus relatively far removed from equilibrium, and that basic slags showed a closer approach to equilibrium, with the water vapor in the furnace atmosphere. Herasymenko2 contended that these conclusions were unjustified, as the oxygen pressure used in the equilibration experiments, ;bout 5 x X atm, was quite different from that found in the furnace. Consequently, during the experiments the slag composition would have changed due to oxidation of ferrous iron. As an extension of Walsh's work and to attempt to clarify this matter, the solubility of water in a basic open-hearth slag was measured as a function of oxygen pressure. Similar measurements were also made on synthetic silicates in the "Fe0"-Fe203-SiO, system. The experimental technique has been described previously by Walsh et a1.l and Uys and King.3 Samples of the basic open-hearth finishing slag, contained in 10-cc platinum crucibles, were equilibrated at 1550°C with atmospheres of different oxygen pressure but constant water-vapor pressure, Ph~o = 0.192 atm. Calculations, as well as measurements, indicate that this figure approximates the water pressure of the combustion gases in a steam-atomized, oil-fired open hearth. Oxygen pressures in the open hearth can vary from 10"2 atm in the combustion gases to between l0-' and 10" atm in the steel bath. The former figure depends on the combustion practice and the latter on the carbon content and temperature of the bath. The oxygen pressure of the slag should lie somewhere between these extremes and is expected to be closer to that of the steel bath than that of the combustion gases. Oxygen pressures were therefore varied between 10" and 6 x l0 atm. At the lowest pressure the slag "puffed up" when quenched (indicating possible loss of water) so experiments were not conducted at lower oxygen pressures. The results are shown in Fig. 1, which includes the water content of the slag "as sampled". The results show that the water content of the slag increased appreciably on equilibration with water vapor at 0.192 atm pressure and that the water solubility apparently decreases with increased oxygen pressure. The solubilities found are comparable to those of the Li20-Ca0-Si02 system.3 Work with synthetic slags in the "Fe0"-Fe203-SiOz system was performed at 1500" C, with Ph20 = 0.192 atrn and for oxygen pressures varying between 10"2 and 10-lo atm. Samples for chemical analysis were prepared as described by Larson.4 The results are shown in Fig. 2. Some low-silica melts tested at low oxygen pressures "puffed up" when quenched and analyzed less than 100 ppm water; these results are not included in Fig. 2. The melts containing 40 mol pct silica also showed a tendency to "puff up" during the quench, when they were tested at the lowest oxygen pressure. These results indicate that, at constant silica content, the solubility of water decreases somewhat with increased oxygen pressure. The effect is, however, small considering the wide range of oxygen pressures studied. Also, at constant oxygen pressure (above about lom5 atm) the solubility increases

Jan 1, 1963

By Kirk A. Mcintosh

Augered, cast-in-place (ACIP) piles have been utilized in the United States for a wide range of projects since the 1950's. Due to the cast-in-place nature of the installation method (and lack of a driving criteria); however, ACIP piles have not been readily accepted by some practicing geotechnical and structural engineers. Since ACIP piles were initially developed, the installation equipment and techniques have been improved and refined and the number of experienced contractors has significantly increased. Over the past 10 to 15 years, the pile type has experienced significant growth in the United States (particularly in Florida) because engineers have become more knowledgeable and comfortable with its use. The Miami area, in particular, has experienced considerable growth in the utilization of ACIP piles primarily due to their usage on the $1 billion Miami Metrorail System project in the early 1980s. The economic advantages over other deep foundation types, coupled with some unique installation advantages, have shown that ACIP piles can be a viable foundation alternative on many projects. Even though ACIP piles have gained respect in the private sector, the pile type has generally not been readily accepted by government transportation agencies. The reluctance to readily accept this foundation type stems primarily from the quality assurance aspect of cast-in-place pile construction. Additionally, there has not been much research activity on this foundation type, technical papers, formal associations (other than the DFI), or a concerted effort to standardize the industry. This paper serves to discuss the state of practice for ACIP pile installation in the state of Florida.

Jan 1, 1997

By T. A. Klinefelter

KYANITE and the related minerals sillimanite, andalusite, dumortierite, and topaz are natural aluminum silicates that can be used in production of mullite (3A1203?2Si02), a superduty refractory material. Kyanite and sillimanite are the dominant ones because of their greater abundance. The only other kyanite-group mineral presently used for mullite production is andalusite. Mullite is not an absolutely essential material as other refractories can be used in the same heat range. However, it is a highly satisfactory one. It is the only compound of silica and alumina that is stable at high temperatures. It has low thermal expansion and is very resistant to corrosive melts and to thermal shock. For these reasons mullite refractories have a much longer life than standard fire-clay refractories under the same conditions. Worldwide, excluding U.S.S.R., the refractories industry consumes about 150-000 short tons annually of kyanite group minerals and synthetic mullite.

Jan 1, 1961