Search Documents

By Joshua Micah Hoffman, Jhon Silva-Castro, Kylie Larson-Robl

A coal mine impoundment failure has the potential to be environmentally devastating and life-threatening. It is well documented that after seismic events slope failures in impoundments can occur. It has been concluded that often the main driven factor of the failure is the increase in excess pore pressure due to ground vibration. A small amount of research has been done regarding the stability of coal mine impoundments under natural seismic events; however no research has been done considering vibrations from mine blasts. If it is taken into account that current environmental restrictions oblige to increase the capacity of coal mine impoundments, thus increasing the hazard of such structures, it is necessary to evaluate the effects of near-by mine blasting on the stability of the coal mine impoundments in order to mitigate and control the potential of slope failures. To study the behavior of excess pore pressure under blasting conditions, scaled simulations of production blasting events were set up inside of a controlled sand tank. The research was divided in two stages. The first one was done, using dry conditions, while in the second part, the same set of tests were performed under saturated conditions. This document shows the partial results for stage one (dry conditions). For the tests, explosive charges were set off within the sand tank at various distances to simulate different blasting distances. Information was collected from geophones, accelerometers, microphones and high speed video camera for dry and saturated scenarios and additionally from piezometers under saturated conditions to assess the behavior of the material under blasting conditions.

Jan 1, 2015

By Anthony S. Spearing

The vast majority of the estimated 100 million rock anchors installed in mines in the USA per year use resin cartridges (Tadolini and Mazzoni, 2006). About 4.5 million per annum of these are bolts with a mechanical shell that if properly installed become effective active supports on installation. In addition, cable anchors (mostly passive) are installed with typically 4 ft of effective resin anchorage length sometimes with mechanical shells, which further makes the installation more difficult. This is because the cable (even with a stiffener tube) is not very rigid. When installing bolts with mechanical shells and cable bolts in the holes, the back-pressure can be so high that the installation is unsuccessful often creating a ?spinner? (an un-tensioned bolt) at best or buckling the bolt thus requiring another bolt/cable to be installed, or leaving a poorly functioning unit. The installation problems can create a significant potential safety hazard and waste time and money. Using a purpose designed test rig that physically inserts different rock anchors into pipes with resin and measure the back-pressure developed with time during the insertion/ installation. The test installation procedure is designed to mirror that used underground by rockbolt operators in coal mines. In addition a computer model has been calibrated that can predict the approximate back pressure of new anchor and resin combinations acting as a screen before physical testing. This research has lead to an understanding and quantification of the insertion back-pressures and this already resulted in improved prototype designs that could lead to more reliable mechanical shell and resin bolt installations.

Jan 1, 2009

Development of Underground Gold Processing Plants Underground gold processing plants have potential advantages over traditional surface installations related to a smaller environmental footprint, reduced capital and mining costs, improved security and increased value of the product delivered to surface. The concept of processing gold ores on the surface is the traditional paradigm. A process of pre-concentration of ore underground is likely to result in a major shift in operating costs. In particular, run of mine ore or a large proportion of it will not need to be transported to the surface. As a result, environmental and financial benefits are likely. Underground plants are likely to be pre-concentration systems where the process product is a high-grade concentrate and tailings for stope backfill. Units will be either static or modular. Concentration methods will be gravity and/or flotation or leach based. This paper discusses the development underground gold plants from early concept, through to the world's first operational unit, a newly commissioned unit and the technical basis of a fully modular system.

Sep 13, 2010

By Pfeifer H. C, Nicacio P. A D

Sinter has been used as part of the metallic charge in large-scale blast furnaces for many years with the well-known benefits in terms of productivity and fuel consumption. However, because of the high investment in a conventional sinter plant, small blast furnaces and the associated integrated mini steel plants have not taken the advantages of using sinter. Recently KTS Korf Tecnologia Siderurgica, a division of Mannesmann Demag Ltda in Brazil, has developed a mini sinter plant for which the investment is compatible with small blast furnaces. Consequently, it is of great interest to evaluate the economical impact of using sinter in such small-scale integrated steel plants. In order to compare two alternatives, ie 100 per cent ore and 70 per cent sinter in the blast furnace burden, mass and heat balances for the entire operation from sinter plant through the blast furnace and EOF-based melting shop, were performed to evaluate the final production cost of the liquid steel. It was found that, depending on the sinter feed price, substantial savings can be obtained with the use of sinter.

Jan 1, 1999

By Jacques Ouellet, Ferri Hassani

"Within the mining industry paste backfill technology has evolved over the last two decades. This technology aims at producing safe and cost effective backfill of high strength. When used as cemented backfill underground the usual practice in the mining operations was to consider the backfill as a component under the production engineer responsibility. With its growing use in various site conditions some problems were encountered. Over time the mechanical characteristics of paste backfill could deteriorate. Investigations on these problems brought an increased understanding of paste backfill chemistry. Effectively, paste backfill is produced with tailings slurry having sometimes very complex chemistry and mineralogy. The bonding agents can be sensitive to the chemistry of these slurries. Today, a new understanding of the complex chemical reactions involved in cementing paste backfill is derived from concrete research literature. Cemented paste backfill is a manufactured product and as thus all steps involved in its making must be looked at. Both the processing engineers and mining engineers need to be involved. The proposed paper will go over the various developments and new understanding gained over the years on paste backfill chemistry. The authors had the opportunity to work with various Canadian mines that implemented paste backfill in their operations. Chemical alterations case study will serve to illustrate the importance of a good understanding of cement and paste chemistry. The authors will then conclude on research orientations needed to bring a more efficient use of paste backfill technology. The crucial role of the processing engineers in the paste backfill manufacturing will be discussed.INTRODUCTIONPaste backfill is usually prepared from a mixture of solids and water containing at least 15% particles smaller than 20 microns with the addition of binders for mechanical strength. Historically, tailings had been classified to extract the fines and only the coarse part was placed underground as sand slurry. Paste fill was researched in the last three decades to enable mining operations to use all the tailings, including fines, in backfill. The outcome of the early studies showed that paste fill provides high strength but due to preparation complexities and transportation problems is expensive. A greater understanding of the transportation mechanisms and advances in dewatering technology in recent years has resulted in more practical use of paste backfill."

Jan 1, 2002

By S. T. Camagu, J. Dutta Majumdar, S. L. Pityana

Laser surface alloying was used to develop copper and molybdenum aluminides by injecting premixed copper and molybdenum powder particles into a laser-generated melt pool on an aluminium substrate. Different laser processing parameters were used to produce the composite thin layers on the substrate material. The microstructure and phase constituents of the composite layer were studied by means of scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), and X-ray diffraction (XRD) techniques. Experimental results show that the matrix structure of the metal matrix composite layer consists of ?-CuAl2and MoAl5. Surface hardness was increased by a factor of 3.

Jan 1, 2015

Suggestions have been made at various times that there may be a recurrence of lodes similar to those at Kalgoorlie in the country to the south of the Golden Mile, but, so far as is known, there has been no geological evidence to support these suggestions apart from the possible extension of the younger quartz-dolerite greenstone in this direction.Geological mapping carried out by the writer in the Coolgardie district in 1946, provided some additional geological evidence to support this claim, and the ideas then held have since been expanded and are now considered to be sufficiently advanced to present them as concrete suggestions. As will be seen from the following pages, the critical area for lode prospecting is Hannan's Lake, where the basement rocks may include younger quartz dolerite greenstone, which, although perhaps distributed over a smaller area than at Kalgoorlie, could, on structural grounds, have a similar fracture system and similar ore deposition.There is little need to stress the importance discoveries in this area would have in prolonging the life of the field, and stimulating the post-war gold mining revival.Previous Work: Only the publications having a direct bearing on the preparation of this paper are given in the list of selected references, but the writer is very conscious of the fact that much other geological work has been carried out in the Kalgoorlie district since its discovery, by the W.A. Department of Mines, by mining companies, and others, all of which has contributed to the present knowledge of the field, and acknowledgment of the value of this work is given herewith. In presenting the suggestions in this paper a broad structural control of ore deposition is assumed, but this has already been established in other parts of the goldfields of Western Australia, including adjacent areas. In the early nineteen thirties, the Western Mining Corporation commenced work on the basis that there was a close relationship between geological structure and auriferous ore deposition, and a similar approach was first made by the Geological Survey of Western Australia in the South Yilgarn in 1935. These ideas were further developed during later surveys, particularly in the North Yilgarn and the Mount Margaret Goldfield.During the Coolgardie Survey in 1946, broad structural mapping was done in greater detail than before, and the structural ideas were implemented and further developed, leading to some success.Other work to which particular acknowledgment is given is that of Stiltwell, Gustafson and Miller, Forman, Prider and Finucane, at Kalgoorlie, and that of Honman in the Kalgoorlie-Coolgardie district, references to which are given at the end of this paper.Valuable constructive criticism of this paper has been given by Professor E. de C. Clarke and Dr. R. T. Prider, of the University of Western Australia.

Jan 1, 1950

By Yi Luo, Jian Yang, Hua Jiang

Surface subsidence induced by underground coal mining activities, especially longwall mining operations, can cause various problems to interstate highways ranging from structural integrity, drivability to safety. Accurate subsidence prediction, correct influence assessments, and effective mitigation measures are the keys to ensure the safety of highway traffic. The surface subsidence prediction program, called comprehensive and integrated subsidence prediction model (CISPM), was developed based on the principle of influence function method and has been validated with a large number of subsidence measurements. In this paper, the techniques to use the predicted final surface movements and deformations for assessing their influence on the integrity and functionality of highway structures (e.g., road surface pavements, concrete slabs, transverse joints, etc.), vehicle dynamics, comfort level, and drivability are presented. A number of mitigation measures to protect the highway structures and to ensure traffic safety are proposed along with an application case.

By Yi Luo, Jian Yang, Hua Jiang

Surface subsidence induced by underground coal mining activities, especially longwall mining operations, can cause various problems to interstate highways ranging from structural integrity, drivability to safety. Accurate subsidence prediction, correct influence assessments, and effective mitigation measures are the keys to ensure the safety of highway traffic. The surface subsidence prediction program, called comprehensive and integrated subsidence prediction model (CISPM), was developed based on the principle of influence function method and has been validated with a large number of subsidence measurements. In this paper, the techniques to use the predicted final surface movements and deformations for assessing their influence on the integrity and functionality of highway structures (e.g., road surface pavements, concrete slabs, transverse joints, etc.), vehicle dynamics, comfort level, and drivability are presented. A number of mitigation measures to protect the highway structures and to ensure traffic safety are proposed along with an application case.

By M. Mankosa, G. Taylor, G. Luttrell, J. Yasalonis

Several industrial-scale HydroFloat separators have recently been installed at Mosaic’s South Fort Meade beneficiation plant for the purpose of improving phosphate recovery and throughput capacity. This technology was implemented after numerous laboratory, bench-scale, and on-site, pilot-scale test campaigns. The results from this detailed test work provided sufficient justification for the complete retrofit of the existing coarse and ultra-coarse flotation cells. Data indicate that the metallurgical results obtained with the full-scale separators are consistent with that obtained during both the bench- and pilot-scale evaluations. The apparent benefits, theory of operation, and commissioning of the equipment are also discussed.

Jan 1, 2007

By T. Bajpayee, L. Prosser, A. Iannacchione

Reducing the number of roof fall injuries is a goal of the NIOSH mine safety research program. Central to this effort is the development of assessment techniques that will help to identify the nature of the risks associated with working under potentially hazardous roof conditions. This paper discusses a method to determine the roof fall risk using a qualitative risk analysis technique. The ability to determine roof fall risk has been a long-standing goal of safety professionals and can provide the kind of information, needed by on-site personnel responsible for worker safety, to mitigate roof fall injuries.

Jan 1, 2007

At Copper Refineries Pty. Ltd., Townsville, two reverberatory furnaces of 420 tonnes capacity are used to melt 210000 tonnes/year of copper for subsequent anode casting. When the refinery commenced production in1959, these furnaces were of 300 tonnes capacity. The original furnaces featured a silica brick hearth, magnesite and chrome magnesite side 'walls, and a sprung silica brick roof, but were unsatisfactory because of thelow refractory life and high costs. With continuous expansion in production and the incentive to increase furnace life and capacity the design of these furnaces has changed greatly since that time.The present furnaces feature all basic brick, a flat suspended basic brick roof, very extensive use of watercooled copper sections, and are of substantially increased (420 tonnes) capacity. Particular attention has been concentrated on high wear areas such as the taphole, side walls, and charging door jambs. Each furnace in its 24 h cycle, is charged, the copper melted, impurities skimmed off, metal "poled" prior to casting, and cast.The service condition during each of these operations is important in considering furnace refractory life.The improvements in operating practices and furnace 'construction which enabled the capacity of the furnaces to be increased are discussed. The life between major repairs to side walls has increased from 90 charges to300 charges.The scope for future improvement is considered and areas for development are suggested.

Jan 1, 1977

By Christopher Mark

The first International Conference on Ground Control in Mining opened with the topic of pillar design. Two classic papers were presented, one by Bieniwski and the other by Wilson. Unfortunately, the two methods were so radically different from each other that it was nearly impossible to reconcile them. Adding to the confusion were the many other pillar strength formulas (such as the Salamon-Munro, the Holland-Gaddy, and the Obert-Duvall, just to name a few) that were also available. Little wonder that discussions of pillar design in those days often ended with anguished cries of ?but which formula is the right one?? The past 25 years have seen substantial progress in the science of coal pillar design. Indeed, one testament to the improvement is the relative scarcity of papers on the topic at recent Conferences. Two factors have been largely responsible for the progress that has been made. The first has been the collection of large data bases of actual case histories of pillar performance in a variety of settings, from shallow room-and-pillar mines through deep cover longwalls. These have made possible the development of empirical design procedures that are closely linked to real world experience. The second important factor is the development of sophisticated computer models that can accurately simulate pillar behavior and roof/pillar/floor interactions. Together, these two lines of research have led to a new understanding of pillar mechanics that identifies three modes of pillar failure: ? Sudden, massive collapse, accompanied by airblast, for slender pillars (width/height<4) ? Squeezing, or slow, non-violent failure, for most room and pillar applications (4<w/h<10) ? Entry failure or bumps for deep cover and longwall applications (w/h>10) It is particularly satisfying that the insights gained from numerical models broadly support those obtained from the empirical studies. While far less controversial than in the past, pillar design problems continue to arise. One recent example is pillar design for highwall mining. NIOSH has just released a software package, called ARMPS-HWM, which employs a number of modern pillar design concepts. Since highwall mining web pillars are long and slender, the greatest danger is that of a sudden collapse. ARMPS-HWM suggests two possible prevention strategies, one which concentrates on the SF of the webs, and the other which creates a ?pressure arch? using properly sized barrier pillars. The paper will close with a discussion of some current needs in coal pillar design, including: ? Updating older empirical methods, such as ALPS, where changes in technology (new types of roof support, more demanding ventilation requirements, faster retreat rates) may have made some of the original case histories obsolete. ? Methods for determining site-specific coal strengths, focusing on bedding plane strength and other factors that may effect confinement, as input for both empirical and numerical design. ? Improved methods for evaluating coal pillar performance for environmental issues, such as surface subsidence and hydrologic impacts, which consider such factors as depth, w/h ratio, water immersion/drainage, and time dependent seam strength.

Jan 1, 2006

By Randolph R. Dreher, Michael L. Schreder

"In recent years, FFE Minerals has designed, installed and commissioned several large grinding mill circuits. This paper discusses the issues related to the erection and commissioning of large grinding mill circuits. The three circuits discussed are Collahuasi in Chile, Minera Los Pelambres in Chile, and Century Zinc in Australia. These circuits include large SAG and ball mills with both gear and gearless drive arrangements, as well as, both trunnion and shell supported mills. Aspects of these features are discussed with respect to their impact on installation and commissioning. While the normal challenges of mill erection and start-up were experienced, there were also a few unexpected challenges encountered partly due to the large scale of the equipment. An overview of the equipment and design ratings of these circuits is also provided.COLLAHUASIOverviewThe Collahuasi mills were started-up in November of 1998. The site is located in the Andes Mountains at an elevation of 4300 meters. The grinding circuit includes two lines featuring one SAG mill and one ball mill for each line. The circuit features a recycle conveyor around the SAG mills with provision for adding a pebble crusher in the future. The design tonnage of the grinding plant is 60,000 MTPD with an ore BWI of 10.5 kWh/MT.The SAG mills are 32’ x 15’ (1 3’ EGL) with 10,800 HP drives. The drive arrangements are dual pinion through pneumatic clutches. The mills are driven by low speed synchronous motors with CCV variable speed drives. The SAG mills are trunnion supported and use hydrostatic lubrication. Feed to the SAG mills is via a rock-box type feed chute on a cart. The mills discharge on to trommel screens with a bucket wheel to remove the oversize.The ball mills are 22’ x 36.5’ (36’ EGL) with 12,500 HP drives. The drive arrangements are dual pinion through pneumatic clutches. The fixed speed mills are driven by low speed synchronous motors with GE Quadramatic load sharing drives. The ball mills are shell-supported and feature multi-pad bearings with hydrodynamic lubrication. The mills are fed via a rubber lined sump box with feed spout on a cart. The ball mills also discharge on to trommel screens. Twenty-six inch (26”) diameter hydrocyclones are in closed circuit with the ball mills."

Jan 1, 2001

In New York City, on the walls of the library of the United Engineering Societies are these words:&quot;Engineering-the art of organising and directing men and of controlling the forces and materials of nature for the benefit of the human race,&quot; but who, reading the schedules of even our best engineering schools, would infer that engineering is an art or that it should always havejn mind the benefit of the human race? While it must be remembered that our engineering schools exemplify the British cult of the amateur, that cult which lets men who have never attended a lecture on &quot;Education&quot; or perhaps nevereven read a book on it, become enginering teachers by profession (and so educators by inference), the root of the matter is to be found in the fact that our educational aims, and consequently our educational practice, seem suited much better to the position engineering held in the community in 1900 than to the position it holds to-day. This civilization of ours has developed, !;loth for good and for ill, into one based largely on engineering achievement; technical progress is so continuous and so rapid that thevalue of descriptive knowledge of current practice is ever lessening; enough must be imparted to make the young graduate immediately employable, and this amount is sufficient for illustrating the principles on which practice is based and on which its advance depends, but the young graduate&apos;s technical progress depends much less on his having acquired additional knowledge than on his ability to acquire knowledge, so, paradoxically, the more useful knowledge there is availabJe the less of it the student should be taught.Less conspicuous but fully as important is the enlargement of the field of work of engineering graduates, especially its extension to the initiating of policies and to the broader problems of administration. At present the road to such positions lies normally through a considerable period of professional work, but it is by no means unlikely that the field will soon include much that requires little professional expel&apos;ience. At all events it is safe to say that the changed. and changing position of engineering in the communitydemands the attention of the engineering schools and that profitable discussion of engineering education demands some understanding of the real nature of education and of the part which engineering plays in the life of the community.THE NATURE OF EDUCATIONUnfortunately &quot;to educate&quot; supplies an example of how words degenerate in meaning; most people regard it as the equivalent of &quot;to instruct&quot;; a small number feel they have gone to. the root of the matter when they say...

Jan 1, 1941

By B. K. Shibler, J. V. Batty, G. M. Potter, H. D. Snedden

"INTRODUCTION As a part of the investigations of strategic mineral deposits in the United States under the Strategic Minerals Act. Engineers of the Bureau of Mines examined and sampled numerous deposits pf fluoride ores in the Western States. Sample from those deposits that warranted further investigation were submitted to the Ore Dressing Section of the Salt Lake Station for metallurgical testing. This paper gives data summarizing the results obtained from laboratory studios of fluorite ores submitted from 12 deposits in Arizona, California, Idaho, Montana, Nevada and Wyomong. Only four of the Ores were found to be amenable to beneficiation for the production of acid-grade fluorspar concentrates with good recoveries. However, all of the samples were amenable to the production of concentrates meeting chemical specifications for metallurgical-grade spar.For the sake of clarity and convenience in presenting data, this report has been divided into six parts, each pertaining to metallurgical studies of fluorspar ores of a single State."

Nov 1, 1947

By Troy Holm, Matthew L. Fuller, Frederick H. Earnest

Virtual Reality Animation Of The Proposed El Dorado Mine In El Salvador Assists Regulators In Reviewing An EIA

Jan 1, 2005

Gary R. Steele is vice president, corporate marketing with Energy Fuels Resources. As such, he knows the global uranium market. The following are some of his thoughts on uranium?s place in the global energy picture. ME: What are Energy Fuels Resources? thoughts on the global nuclear power industry? Steele: The global nuclear power industry is a major contributor to the electrical needs of the world. Though generation by nuclear reactors has primarily attracted attention through the reactor accidents at Three Mile Island and Chernobyl, nuclear power continues to quietly and safely provide power to a growing and power-hungry world population. As of March 2008, 30 countries were operating 439 nuclear power reactors. Nuclear power plants provided about 15 percent of the world?s electricity production in 2007. France leads the world in nuclear utilization, with 77 percent of its power coming from nuclear plants. And Lithuania, Slovakia and Belgium each derive more than 50 percent of their power needs from nuclear plants. For much of the developed world, nuclear generation has already been contributing significantly to the supply of electricity. Additionally, 34 new nuclear plants are under construction in 14 countries. Leading the rush to build new nuclear generating plants are China, Russia and India. Each of these countries is building six new nuclear power plants. These 18 plants, totaling almost 12,000 MW of generation capacity, will require about 7.25 kt (16 million lbs) of U3O8 for their initial fuel load and will consume about 2.45 kt/a (5.4 million lbs/year) for the rest of their operating lives. The rest of the world, outside of the United States, has used nuclear power as a viable and economic generation alternative since the commercialization of utility nuclear reactors. And current activity supports the strong future of the nuclear alternative internationally.

Jan 1, 2008

By A. G. Merma

In this work, the electrocoagulation technique was studied in order to treat chemically stabilized concentrated oil-water emulsions. This study was mainly focused on the effects of operating parameters such as initial pH, current density, reaction time, electrode distance and inlet concentration on the separation of oil as measured by the chemical oxygen demand -1(COD) method. The synthetic emulsion was prepared from Shell - Talpa 30 oil (3g.L-1) and sodium dodecyl sulfate (1.0 g.L), having a Zeta potential around -70 mv at pH 8.7. The process was carried out in an electrocoagulation cell with a set of four parallel monopolar electrodes. This set consisted of two aluminum plate anodes and two 316L stainless steel plate cathodes. Kinetic curves showed that the electrocoagulation process exhibits three phases: (1) an initial phase, where the COD did not decrease because the solution had not reached the minimum amount of dissolved aluminum required to cause the break-up of the emulsion, (2) a reactive phase during which COD decreased due to possible agglomeration of the precipitates and (3) a steady-state phase where the COD did not change. The results showed that the period to reach the reactive phase decreased as the current density increased and the pH values decreased.

Jan 1, 2009

By Dan Witkowsky

Beginning on June 11, 2007, as many as 36, kindergarten-to-grade-12 (K-12) teachers will participate in a program designed to educate them all about the mining industry. The 39th Annual A Total Concept of the Mining Industry – All About Mining, will be conducted by the Colorado Mining Association Education Foundation, Inc. (CMAEF) and the Office of Special Programs and Continuing Education (SPACE) at the Colorado School of Mines. This flagship program includes four intensive weeks at the Colorado School of Mines. During that time, more than 75 volunteer lecturers will “educate the educators” about mining and its importance to the United States and the world. During the learning process associated with obtaining a basic understanding of mining and all its aspects, the teachers will be hosted by hundreds of other industry professionals at 10 Colorado mining operations. Also visited will be a government earthquake center, a museum of mining and industry, an earth mechanics laboratory, a metallurgical research center, a metallurgical concentrator, an electric power plant and a steel mill. Questions before, during and after visits will be answered by another select group of volunteers who will travel with the teachers to the various sites.

Jan 1, 2007