Search Documents

A thermochemical model is developed to study the two-stage smelting reduction process for ironmaking without post-combustion. Steady-state multi-material and heat balance equations are solved simultaneously to study the effect of metallisation, slag basicity, coal rank and heat loss on consumption rates of coal, ore, flux and oxygen and production rate of slag to produce hot metal of a given composition, tapped at a given temperature. The model is applied to the commercial data for a COREX-plant producing a wide range of hot metal compositions, tapped at different temperatures. The computed rates of coal, slag, flux, ore and oxygen were found to be close to the reported ones, but an exact match could not be obtained. It is found that a four per cent change in metallisation brings changes the coal rate by five per cent, flux rate by six per cent, slag rate by eight per cent and oxygen rate by 13 per cent, while a ten per cent change in basicity changes the coal rate by ten per cent, flux rate by 13 per cent and oxygen rate by 22 per cent. Further, it is found that an increase in metallisation decreases the coal rate and export gas. At a given per cent metallisation, the coal rate and the export gas are lowest for anthracite compared to all other types of coal.

Jan 1, 1999

By Konstantinos Modis

According to recently established theoretical analysis and under certain conditions, a critical sampling density can be determined for an earth-related space-distributed natural variable. Sampling above this critical limit adds little to the mapping results. The objective of this paper is the application of the above theory to the Sesklo clay quarry in Greece, where Heracles General Cement Company had conducted a sampling campaign to estimate its reserves. The structural analysis of Al2O3 values generated a variogram model, from which the critical sampling density was identified. This critical number was by far lower than the existing sampling density. Clay reserves were then estimated using geostatistics and inverse distance squares in different data schemes with variable densities. The results of the comparisons between the various models revealed that, when the sampling density was greater than its critical value, geostatistics and deterministic interpolation gave similar estimations, which is also in agreement to the theory. The optimal sampling grid finally proposed here, will result to significant cost savings in the next drilling program which is now in plan by the company.

Oct 1, 2009

The development of a noise attenuated compressed air driven fan is described. The fan, which employs the jet reaction principle, possesses blade extension pieces which penetrate into an acoustically treated annular chamber. The dominant noise source, namely the air jets, is thereby partially suppressed. In addition, the increased moment arm of the jets leads to an improved propulsion effect which contributes to the improved aerodynamic performance of the unit.A typical measure of the improvement of this type of auxiliary mine ventilation unit is a 4 per cent increase in efficiency and a 10 dB (A) drop in sound level for a fan duty of 0·5 kPa and 1600 litre/s. This degree ofattenuation corresponds to at least halving the loudness level, a subjective noise measure.

Jan 1, 1973

By Thomas Passlick

By means of further developed machines and techniques and with growing experiences in jet grouting, the challenge of this building method becomes more and more complex. To keep the concerning risks as low as possible, the requirements on the quality assurance continuously in­crease. The construction of a 37.0m deep seated slab for the Amsterdam metro station Vijzelgracht in marine clay represents such a complex task. This paper summarises the required measures of quality assurance. In particular a new hydraulic measuring device is introduced with which it was possible to detect the column diameter of 2.6m at a depth of 37.0m during the production process and with a very high accuracy.

Jan 1, 2006

By T. Bajpayee, J. Ellenberger

Microseismic monitoring and evaluation is one aspect of the National Institute for Occupational Safety and Health (NIOSH) research program. Roof falls are often preceded by a period of elevated microseismic activity, but not all periods of elevated activity result in a roof fall, nor do all roof falls occur after some amount of elevated activity. The objective of this study is to review periods of elevated microseismic activity and determine whether fracture activity rate can be used to anticipate the initiation of roof falls. The study was carried out at an underground limestone mine where major roof falls are associated with excessive horizontal stress. The progression of roof falls was detected by the microseismic signature produced by the rock falling from the mine roof onto the mine floor, which is termed a roof fall impact event. A total of nine elevated fracture activity periods that resulted in seven major roof falls were examined. It was observed that elevated fracture activity preceded the initial roof fall impact event in three out of four major roof falls. The initial impact event was not identified for the remaining three roof falls. Fracture event rates were analyzed and a roof fall alarm trigger of five fracture events in a ten minute time period was established for this test case. The fall alarm trigger was tested against six of the elevated activity periods. Four roof falls occurred in the six periods of elevated activity, and two would have triggered the alarm before the roof fall occurred, while two false alarms were generated. The results show that limited success would have been achieved by the microseismic system as a roof fall alarm trigger. However, the trigger would have been successful at warning of the onset of elevated activity, allowing mine employees to respond appropriately. The study highlighted some issues with implementing such a system in an operating mine, including the need for real time identification of fracture related microseismic signals among mining induced signals, and accurate location and identification of fracture clustering.

Jan 1, 2007

The seams of black coal occurring in Victoria are so disturbed by faulting, wash-outs, thinning, etc., that it is necessary, for the prevention of costly errors in development, that close boring be undertaken so that the correct positions of the shafts, tunnels, main and auxiliary roadways can be set out in order that the area can be economically worked. The State Coal Mine has two boring plants continuously at work, which have given good service for the last twenty-five years.The information supplied herein is merely our experience in boring at the State Coal Mine over an extended period. The type of plant in use is that known as the Victoria Drilling Plant, equipped with an 11 h.p. portable oil engine, using power kerosene as fuel. It was purchased in 1914, complete with mechanism for cable drilling, capable of boring to a depth of 1500 ft. with a guarantee of 1000 ft., with Calyx cutters, boring rods and all necessary equipment for the sum of £1473. The chief mechanical features of the plant are as follows:-The derrick is in the shape of a tripod (see Fig. 1), two of the legs being of steel channel built together to form a frame which, when lowered on to two sets of road wheels, forms a carriage for the transport of a portion of the boring equipment. The third leg is made of oregon in the form of a double bow, with bolts and distance pieces between the wooden sides. The top of this is hinged on to the steel frame, and the bottom is fitted into a cast iron block, having two small wheels to facilitate erection. A rope attached to the cast iron block and to the winch easily...

Jan 1, 1936

By Peter W. Kauffman

This Bureau of Mines publication is designed primarily to provide mine engineers and production-level mine managers with the following: 1. Information to assist them in making the decision to retreat mine and in selecting the best retreat mining technique for specific mining conditions. 2. Information on mine planning that will enable them to design mine layouts for safe and efficient retreat mining. 3. Information that will enable them to develop a section foreman's handbook. The manual has been organized to gradually increase in level of detail as the reader progresses from beginning to end. Individuals interested in an overview of retreat mining can confine themselves to the first few chapters. Those interested in mine planning, should read the middle chapters as well. Those interested in the development of a foreman's handbook should read the entire manual.

Jan 1, 1981

By Edwards A. B

A suite of specimens from the newly developed Black Star copper ore body at Mount Isa was made available for mineragraphic study by the Mount Isa Mines, Ltd. The specimens were selected as representative of the different phases of mineralisation found in the ore body, rather than with a view to furnishing a complete cross-section of it; and the examination has been carried out with a view to ascertaining (1) the nature, extent and association of the arsenic, antimony and possibly bismuth, minerals in the ore, (2) the mode of occurrence of silver in the ore, and (3) whether galena and sphalerite occur in minute forms well below the sIzes readily observed in hand specimens.Analyses of the January to June, 1944, mill head composites show that the proportions of the elements Ag, As, Sb and Bi in the ore are as follows:Ag 0.000013 = 0.35 oz./tonAs 0.024Sb 0:002Bi 0.0005The copper content of the mill heads ranges from 3.5% to 4.75%, the lead content from 0.03% to 0.08,% and the zinc content from 0.09% to 0.23%.MINERAL COMPOSITIONThe specimens range from massive sulphide ore, consisting of areas of chalcopyrite, pyrrhotite, and rarely sphalerite, from 1 to 3 cm. across, to fragments of extremely finely banded pyritic shale in which no minerals other than pyrite are visible. The gangue associated with the massive sulphides is chiefly dolomite, and sometimes white quartz. The pyritic shale fragments show evidence of shearing and faulting on a micro-scale, the fractures sometimes being filled with sulphides and vein minerals.The ore minerals found in the polished sections are pyrite, arsenopyrite, marcasite, sphalerite, chalcopyrite, valleriite, chalcostibite, galena, dyscrasite, jamesonite, magnetite, gold, graphite and rutile.Pyrite (FeS2)Pyrite occurs chiefly in two forms according to whether deposition took place along the bedding planes or along the intersecting faults and fractures. Deposition of pyrite along the bedding planes of dense, thinly banded shales ha,s produced a metasomatically altered shale in which the pyritic bands are from 0.02 to 0.03 mm. wide, and alternate with bands...

Jan 1, 1945

Basic parameters affecting the stability of foams have been studied. We used the thin film pressure balance (TFPB) technique of Scheludko and Exerowa (1959) to measure the surface forces in foam films stabilized with various frothers such as pentanol, octanol, MIBC, and PPG. The results were compared with the froth stabilities measured using the shake tests and the film elasticity calculated using the model developed by Wang and Yoon (2006). It was found that the froth stability is controlled by both film elasticity and surface forces (or disjoining pressure), the relative contributions from each changing with frother concentration and type.

Jan 1, 2006

When the first rush of miners took place on the Molyneux River, in the Dunstan Gorge, the gold was won by means of cradling the gravel, which was shovelled from the various beaches and crevices in the rock-bound sides of the river.The above method of winning the gold was only practicable when the beaches were not covered with water, hence the work was usually carried on during the winter months, the ordinary level of the river during spring and summer months being some ten or twelve feet above winter level. The melting of the spow in the Lakes water-shed being responsible for the high summer level of the river.As the available beaches were worked out, other methods of winning the gold were proposed and worked with more or less successful results the first advance being to work the bed of the river by means of a spoon dredge. The spoon was made with a round lip or ring of iron, having a steel cutting edge on one half of the circumference, at the opposite side a socket being forged to take a long spar or boom, which was securely fitted thereto. At intervals round the hoop, half-inch holes were bored to enable. a bullock-hide bag to be laced on to same. The spoon was worked from a pontoon which carried a crab winch, tackles and the necessary washing appliances to treat the washdirt lifted. In starting to dredge, a tackle was attached to near the upper end of the boom, and a line or chain was carried over a cat head from the crab winch...

Jan 1, 1901

By A. J. Potgieter, C. Hill, A. Humpel, D. S. Magudulela, V. Scholtz, A. Coetzee

Keywords: Pyrometallurgy, long steel products, coke, sinter, blast furnace, steel plant Located in Northern KwaZulu Natal, Mittal Steel South Africa Newcastle works produces roughly 1.8 million tons per annum, supplying long steel products, locally and overseas. The great extent of local raw material availability and low conversion cost ensures that Mittal Steel South Africa is among the lowest cost, high quality producers of steel. MSSA Newcastle works can be subdivided into two main sections: The iron making side, comprising the coke ovens, sinter plant and blast furnace, and the steel making side, comprising the basic oxygen furnace, ladle furnace, continuous casters, and the medium, rod, and bar mills.

Jan 1, 2006

By J. Daraisme

Société le Nickel (SLN) exploits the Dôme lateritic nickel orebody at its Tiébaghi operations in New Caledonia. The site geology has an obvious bearing on recovery and metallurgical performance, and the controls are extremely complex at all scales: lithology, oxidation-reduction conditions, mineralogy, and multivariate geochemistry. In that context, establishing an adapted recoverable resource estimation method that is efficient and transparent proves an interesting challenge. The method must address the key notions of: ? Support effect: the exploration data-set can only warrant the estimation of large panels 20×20×3 m3, which are much larger than the selective mining units (SMUs) of 5×5×3 m3 ? Information effect: the selection at production stage uses estimates based on information much denser than that available for mine planning. The problem is rendered more complex in this type of deposit by the fact that the additive variables used for any estimation process (metal accumulation and ore tonnage) are not the ones used to establish the selection at mining stage (i.e. the nickel grade of SMUs, which is the ratio of accumulation on tonnage). Eventually, the selection criteria involve not only Ni grades but also other constituents such as Al2O3, Fe2O3, MgO, and SiO2. The solution presented in this paper is the construction of a platform of SMU multivariate simulations in the saprolitic horizon, together with efficient post-processing aimed at producing the multivariate recoverable resource estimates. The efficiency constraints imposed by the number of blocks to be simulated (1.5 million) lead to resorting to direct block simulations. The underlying multivariate discrete Gaussian model (DGM), the validity of which is tested beforehand, is put to good use to mimic the selection process at the mining stage, by offering the ability to simulate in each block a composite value located at random within the block. Finally, the paper presents the application of a scenario reduction algorithm to pick a representative subset of a few simulations to help appraise the risk attached to the downstream phases (reserve optimization, mine sequencing) of the project. The implementation presented here is for the first generation of the Scenario Reduction plugin built in Isatis software, where measuring the distance between the initial set of scenarios and the reduced set is based on Ni quantities only. Research is under way to adapt the measure to the true multivariate nature of the problem.

Jan 1, 2014

"In mining operations, it is widely accepted that strategies to drive operational goals must revolve around improving plant availability, reliability and process efficiency. In this paper, an integrated solution framework for reducing process variability, increasing process efficiencies and maximizing plant availability and reliability is discussed within the context of a typical milling circuit. The framework exploits a real-time analysis “gap” evident in production operations that prevents timeous identification of equipment and process failures. This is achieved by leveraging predictive analytics for equipment health monitoring, control loop monitoring and advanced regulatory control solutions towards enhanced process performance, improved asset management and regulatory compliance. The framework provides for early and actionable warnings on equipment and process degradation using real-time operational data.INTRODUCTION The changing landscape of gold mining and processing presents many challenges that threaten sustainability of existing (marginal) operations as well as deter investment in new projects. As existing “shallow” ore resources become depleted, mining operations are increasingly treating low-grade ores with complex and randomly variable mineralogical characteristics. For example, in South Africa, historically one of the major gold producers, the average grade of ore treated has been decreasing from averages above 4.5 – 5 g/t to current grades averaging less than 3 g/t within a decade (Chamber of Mines, 2012). Moreover, lower tonnages are being treated as a result of the narrowing of the available resource base. Also, the regulatory framework has tightened over the years due to heightened concerns on the safety, health and environmental impacts of mining and related activities."

Jan 1, 2014

By Chris Fleming, John R. Goode, James Brown

"Data will be produced from two uranium feasibility studies that were conducted in 2008, both involving uranium recovery from leached slurry by resin-in-pulp (RIP) with strong base resins. Excellent metallurgical results were produced in RIP pilot plants in both studies, and the loaded resins were eluted with strong sulphuric acid and recycled to RIP in an integrated process. Resin losses by either abrasion or mechanical breakage were immeasurably low.Metallurgical results from these two campaigns will be presented, along with an economic analysis of RIP versus the alternative process of CCD or filtration and solvent extraction.INTRODUCTIONThe recovery of uranium directly from pulp with strong base resins in RIP contactors was practiced commercially in the USA in the 1960s, but the process never established itself as a viable alternative to solid/liquid separation and solvent extraction. This was due mainly to the necessity to do a sand-slime separation partially resulting from the unavailability of coarse resin beads, inadequacies in the design of the RIP contactors and screens to separate resin from pulp, as well as problems with the strength and durability of resins in agitated pulps.There have been significant advances in the last 30 years in each of these areas. All the commercial resin manufacturers are now producing very tough, durable, strong base resins, and are manufacturing them in a large bead size that is better suited to RIP applications. In addition, with the emergence and wide spread implementation of the carbon in pulp process in the gold industry in the 1980s, many innovative techniques for preparing leached slurries and separating carbon from pulp have become firmly established. These techniques have proven to be equally applicable to resin separation from pulps in RIP contactors."

Jan 1, 2010

By Qinghua Tian, Zhipeng Xu, Dong Li, Xueyi Guo, Liu Zhu

A possible process for extracting tellurium and antimony from a residue generated in alkaline sulfide leaching of telluriumbearing alkaline skimming slag was proposed. The central composite design was employed to define the optimal leaching conditions for tellurium and antimony extractions from the residue sample. Using a 23 factorial matrix, the best performance for tellurium and antimony extractions (96.36% and 99.64%) were obtained at 175 g L−1 Na2S concentration for 80 °C during 60 min. The notable degree for influencing tellurium and antimony extractions was leaching temperature, Na2S concentration, and leaching time. The analysis of variance results indicated that the regression model was significant and suitable to be used for the optimization of independent variables within the range. The model was validated under optimal operating conditions based on the experimental design results. Antimony and tellurium in the leach liquor were separated and recovered by H2O2 oxidation followed by Na2S-Na2SO3 reduction. 98.93% of antimony was precipitated selectively during H2O2 oxidation, while 95.06% of tellurium was precipitated during Na2S-Na2SO3 reduction. NaSb(OH)6 and elemental tellurium was obtained as the product.

In presenting this address I am conscious of the honour that has been paid me in my election to this important office, and I am very aware that I follow, in the position of President, many distinguished men who have led the Institute over the 70 years since its inauguration in Broken Hill in 1893.It is perhaps appropriate tonight that I intend to talk about a metal which recalls the birth-place of the Institute, and is also one with which I have had a direct association throughout the whole of my working career. This metal is Silver.Silver is associated traditionally in everyone's mind with money and silverware, and has always been prized for its natural beauty and elegance. It is today one of the few metals in which world consumption has outstripped production, and the events which have occurred to bring about this situation make an interesting story.In telling this story, I propose firstly to indicate our development as a silver producing country, give an historical review of the metal, trace its use as currency and the factors influencing its price, and then say something of the old and new uses of silver. Finally I shall give some comments on silver production in Australia today.Australia, with 6-5 per cent of the world's output of silver, ranks sixth among the producer countries and over the years has contributed 892.5 million ounces to the world's supply which, based upon production since the discovery ofAmerica, is estimated to have been 22,150 million ounces or nearly 680,000 tons.Although our production appears relatively small by...

Jan 1, 1963

"The link between ore texture and mineral liberation has previously been established at a microscopic scale. To construct ore texture models that can be used in mining applications requires this relationship to be retained at a significantly larger scale. This is initially dealt with by finding a basic set of microtextures that form the elements of the ore textures at the next larger mesoscopic scale, simulating these mesotextures at a fine scale, then changing the support of the mesotexture simulations to generate the expected mining block/stope mesotexture distributions. Thus, a mutually exclusive and exhaustive set of spatially locatable mesotextures can be used to fully characterize the metallurgical properties of in situ material.A method that generates expected distributions of mesotextures for any mining block size or shape is proposed, and includes: (1) characterizing the spatial correlation of the set of mesotextures with a single covariance function; (2) generating multiple simulations of mesotextures at a fine scale; and (3) using the simulations at a fine scale to generate the expected mining block/stope mesotexture distributions. A case study, using the George Fisher sediment-hosted base metal deposit in Queensland Queensland, Australia, is developed to demonstrate the proposed methodology as well as show the inadequacy of off-the-shelf approaches.Mining-scale texture models can be used to improve the in situ discrimination of ore from waste by exploiting the joint spatial variability of grades and textures to quantify the expected metal recovery of in situ material, then calculate local marginal cut-off grades. An artificial case study is presented to demonstrate the changes in ore/waste selection when considering ore texture models compared to constant metal recoveries."

Jan 1, 2005

By Rees J. Llewellyn

High chromium white irons can be formulated to provide required combinations of abrasion and erosion wear resistance, toughness and capability to withstand corrosion attack. As a consequence, they are used widely in casting form throughout the mining/mineral processing industry, particularly as components for slurry pumps and also as mill and crusher liners, laminated wear plates in chutes and hoppers and in valves, nozzles and cyclones. Traditional cast chromium molybdenum and high chromium white irons for wear applications are covered in ASTM A532 Classes 11 and 111 and are also available as comparable proprietary alloys. They rely on heat-treated, hypoeutectic microstructures containing a high volume fraction of very hard eutectic/secondary metal carbides and martensite to provide extremely high wear resistance. The ability to increase the carbide volume fraction and hence achieve higher wear resistance, has been limited because of severe casting difficulties encountered when carbon and chromium contents are raised and hypereutectic alloys with structures also containing coarse acicular primary metal carbides are produced. The limitation has been overcome and cast hypereutectic chromium white iron pump components have established themselves in a wide variety of mineral processing service applications. Comparisons will be made between the microstructures and wear test performance data for the various alloy types and details will be provided of the service performance improvements that have been achieved through the use of hypereutectic chromium white irons.

May 1, 2004

Terramin Australia LimitedÆs Angas Lead and Zinc Mine operates in the unique and picturesque environment of Adelaide Hills, 60 km South East of the Adelaide city centre itself. The mine was granted approval for construction by the South Australian Government in April 2007 and the Process Plant was constructed and commissioned in July 2008. This paper outlines the background to the plant design and the approval process given the close proximity to the local town of Strathalbyn, with a major focus on the commissioning learnings from the Concentrator startup for future reference and a review of the operational performance of the Concentrator throughout the first year of successful production versus design and expectations.

Jan 1, 2009

The coal-bearing regions of Colorado cover approximately 29,600 square miles, which is 28.4 percent of the state's total area. The most important coal-bearing regions are located in the north western and west-central parts of Colorado. Coal resources vary from lignite to anthracite. More than 70 percent are bituminous; 23 percent subbituminous; 5 percent lignite; and less than 1 percent anthracite. The state's coal reserves total about 17.2 billion tons, 3.5 percent of national reserves. Approximately 8.8 million acres of coal rights in the state are owned by the Federal Government; on about 72percent of this land, the Federal Government controls both the coal and the surface rights. It is estimated that approximately 4.2 billion tons of coal reserves are under federal ownership in Colorado. Permitted acreage of mines in Colorado ranges from 40 to 13,114 acres. Differences in elevation create many climatic zones in Colorado. Local annual precipitation can average less than eight inches in some areas in extreme western Colorado to more than 30 inches in certain mountainous areas. Generally, precipitation rates are low at most mine sites, making revegetation difficult. Colorado gained primacy when its regulatory program was conditionally approved December 15,1980. The Abandoned Mine Land Program was approved June 11, 1982.

Jan 1, 1992