Search Documents

By G. H. Khoe

Neutralisation of acid uranium mill tailings with lime or other alkaline materials is usually practised to reduce the dissolved concentration of heavy metals and radio nuclides. Computer modelling of this process was carried out using the geochemical equilibrium code MINTEQA2. Computed dissolved metal and sulfate concentrations were compared with laboratory-based experimental data. It was found necessary to include the modelling of adsorption of trace metals (such as uranium and lead) by the precipitated ferric hydroxide in order to obtain acceptable concentrations in the neutralised liquors. There were limitations of the modelling exercise due to important aspects which were not addressed or properly accounted for such as chemical reaction kinetics and the effect of high ionic strength. These are discussed in the paper.

Jan 1, 1991

By Qinghai Pang

"With the increasing proportion of bituminous coal in blend coal, the safety of blend coal during pulverization and transportation is gradually being paid more and more attention. Therefore, the explosivity of bituminous pulverized coal (PC) with different volatile content from 25 to 38% was studied by measuring the combustion flame length after its injection into a glass pipe with the heat source installed in the center. The results indicated that high volatile content bituminous PC is apt to have higher explosivity. By blending different bituminous PC with 10% anthracite, the explosivity of bituminous PC showed a positive correlation with the proportion –OH radical. However, different bituminous PC seemed to have the same explosivity when the addition of anthracite increased to 20%. With the further increasing proportion of anthracite to 30%, the explosivity of bituminous PC with high –OH proportion became negligible while a weak explosivity of high –CH3 proportion bituminous PC still remained.IntroductionWith the increasing iron ore prices and decreasing steel prices, it has become critical for iron and steel enterprises to control the cost in ironmaking and steelmaking process. Blast furnaces (BF) are the main consumer in ironmaking process, which occupies 70% fuel consumption of total steelmaking process [1]. In this circumstance, any means necessary is taken by BF operators to lower the cost of iron in production. Coke and iron ore are the main expense in this process, who takes up a very high proportion in total cost. Pulverized coal injection (PCI) is the most efficient way to reduce coke ratio, which replace coke with relatively cheaper PC.At present, most of BF is injected with blend coal in the consideration of decent combustion property and quantity of heat. Simultaneously, bituminite and anthracite blending is an effective method to obtain blend coals with required composition and performance, such as volatile and ash content, etc. Nevertheless, a very huge gap was found between the price of bituminous coal and anthracite in some regions of China, in which the price of bituminite can be just 70% of the price of anthracite. Thus, iron enterprises in these regions attempt to possibly amplify the proportion of bituminite in blend coal. Increasing proportion of bituminite results in higher volatile content in blend coal, by which the safety of blend coal during pulverization or transportation was deteriorated.Relatively, coals with higher volatile content usually possess stronger explosivity, which means that volatile and explosivity may related to some extent. However, the relationship between volatile and explosivity is not of certainty for some PC with high volatile content around 40% was found to be inexplosive in comparison to the coals with lower volatile content. With the increasing proportion of bituminous coal in blend coal, investigations on the factors of PC explosivity have become more and more important. Therefore, bituminous coals with different volatile content were selected. The explosivity of blend coal and its relationship between volatile content and functionality was investigated in this research."

Jan 1, 2014

By J. Rastas

The recovery of lead, silver and gold from existing and potential zinc process residues using a sulfidization-flotation method was investigated on a laboratory scale. The following residues were tested: neutral leach residue, high acid leach residue, and hematite residues. The sulfidization of lead and silver is carried out at low pH by the addition of a stoichiometric amount of sulfide at a controlled rate. To increase the particle size of the sulfides, seeding with synthetic lead and silver sulfides -is employed. The flotation is carried out at pH 2-4 using low pH-collectors such as dithiophosphates and dithiophosphinates. Special attention must be paid to the role of oxygen in the conditioning stage. The effect of different parameters on both the sulfidization and the flotation has been evaluated. Recoveries of 85-90, 90-95 and about 80 % were obtained for lead, silver and gold, respectively. Typically, concentrates containing 50-60 % lead, 3-5 kg/t silver and 10-15 git gold were produced.

Jan 1, 1990

By Jinxing Ji

Several fundamental aspects related to the nickel electrowinning from chloride electrolytes have been addressed in this paper. The thermodynamic study includes the activity coefficient of the hydrogen ion and the speciation diagram of NiCI2 solutions. The activity coefficient of the hydrogen ion (YH+) was calculated and estimated experimentally using a combination glass pH electrode. It was found that YH+ was greater than one in concentrated NiCl2 solutions and increased significantly with increasing NiCl2 concentration. The speciation diagram for NiCl2 solutions was plotted with YH+ and the effect of the ionic strength on the equilibrium constants being taken into account. It was discovered that the predominant nickel species in the acidic region were Ni2+ and NiCI+ in 0.937 M NiCl2 solution at 25°C. Electrodeposition tests demonstrated that higher Nit' concentration in the electrolyte improved the current efficiency of nickel electrodeposition (CENi). The additions of H3BO3, and NH4Cl increased very little the current efficiency of nickel electrodeposition at pH 1.5 and temperature 60°C. However, the addition of sulfate decreased the current efficiency of nickel electrodeposition. Nickel electrodeposition was also found to be a steady-state process since the amount of acid added to the electrolyte at a constant pH increased linearly with time during galvanostatic electrodeposition. The cathode surface pH during nickel electrodeposition was measured using a flat-bottom combination glass pH electrode and a 500-mesh gold gauze as cathode. The cathode surface pH was found always to be higher than the pH in the bulk electrolyte, and if the current density was sufficiently large, it would eventually reach a level causing precipitation of insoluble Ni(OH)2(s) on the cathode surface. Rotating disc electrode studies revealed that the rate of nickel electrodeposition was first order with respect to the activity of nickel ion and zero order with respect to the activities of chloride and hydrogen ions. The rate of hydrogen evolution was found to be first order with respect to the activity of hydrogen ion and to be zero order with respect to the activities of nickel and chloride ions. These findings indicate that nickel deposition and hydrogen evolution proceed independently.

Jan 1, 1995

By Nagy El-Kaddah, T. T. Natarajan

This paper describes a novel approach for modeling three-dimensional electromagnetically driven flow in inductively stirred systems, and its application to modeling electromagnetic and flow phenomena in sub-mold rotary stirring of billets. It is based on a new T-\jf potential formulation of electromagnetic field, which does not require the calculation of the field in free space. A finite element algorithm has been developed for solving the electromagnetic field and Navier-Stokes equations in the fluid flow domain. The computed results have shown that the electromagnetic force field generates a strong rotational flow within the vertical section covered by the stirrer, and a relatively strong secondary flow beyond the stirrer. It has also been shown that the rotational and secondary flows were driven primarily by the vorticity of the force field at the billet corners. The induced flow in the molten pool was found to be turbulent and the effective mixing region in the molten pool was about three times the length of the stirrer. The mathematical approach presented in this paper provides the theoretical framework for quantifying these effects for any given stirrer configuration and operating parameters.

Jan 1, 1999

By Yurniko Nakamura

Hydriding properties and crystal structure of a Ti-V- Mn solid solution alloy have been studied by P-C isotherm measurements and neutron and X-ray powder diffraction. The absorption P-C isotherm at 298K shows two plateau regions at 0.01MPa and 1MPa. The X-ray diffraction data have demonstrated that three phases with a BCC, a pseudo-cubic FCC and an FCC structure form subsequently with increase of the hydrogen content. Crystal structure of the latter two phases has been determined by Rietveld refinement of the neutron diffraction data. The FCC phase is the di-hydride of CaF2 type with hydrogen occupation in the T sites. The pseudo-cubic FCC phase is the mono-hydride of NaCl-type with hydrogen occupation in the 0 sites, which has not been reported so far. The lattice constants of the mono-hydride (Ti1.0V1.1Mn0.9)H_2.7 are a'=0.407 nm for two axes and c'=0.390 nm for the third axis. The a'axis is shorter by 4% than the c'axis. This pseudo-cubic FCC lattice is formed by contraction of 5% of the a axis and expansion of about 30% of the c axis from the original BCC lattice.

Jan 1, 2002

By Joel A. Huffinan

"This presentation is being given to better inform the audience of the dependability of precious metal analysis by fire assay. A brief explanation, however, of standard fire assay exploration procedures will be given. An overview of other types of analyses by fire assay will be discussed as well, and the operation of a modern day assay laboratory.IntroductionThe use of lead oxide for the fire assay process dates back to the finds in Troy II and the Cappadocian Tablets about 3,000 B.C. Some advances have been made in the basic procedures due to instrumentation and electronics, but the fusion and cupellation procedures used in fire assay remain much the same as during this period.In 1600 AD. Agricola was the first to take a scientific approach to fire assay recording methods and procedures used (Hillerbrand and Allen, 1905) [1]. Since this period, much of the recognized research into the analysis of ores and metals was carried out in the late 1800's and early 1900's prior to World War II, and again after the deregulation of precious metals. The renewed interest in precious metals mining and metallurgy are due much to advances in precious metals heap leaching in late 1970's."

Jan 1, 1999

By Benoit DeBecker

Laboratory-scale experiments have shown that chromium metal could be recovered from chromate wastes by modifying slightly the chromium electrowinning flow-sheet. After reduction by sulhr dioxide and precipitation of chromic hydroxide, the solid residue is dissolved in the chrome alum solution and the metallic impurities are removed by cementation on manganese. The presence of dissolved manganese in the electrolyte does not affect the cathodic deposition of chromium and it eliminates the anodic production of Cr(V1).

Jan 1, 1994

By Satu Strömberg

Four different nickel concentrates were oxidized in a laboratory scale laminar flow furnace in simulated flash smelting conditions. The major nickel- and iron-bearing minerals in the con- centrates were pentlandite, violarite, gersdorffite, and pyrite and pyrrhotite, respectively. Thermal decomposition, ignition and oxidation behavior of nickel and iron sulfides were examined by using optical and scanning electron microscopy. General reactivity of the concentrates was monitored with sulfur removal which was most effective in violarite-based concentrate. Pentlandite-concentrates needed higher experimental temperatures for complete desulfurization and gersdorffite-based concentrate contained 5 - 10 % of the original sulfur even in the most oxidizing conditions studied (1 100°C, 50 vol-% 02). The reactivity of the iron minerals was found to depend on the other minerals present in the concentrate. In this paper, the observed re- action products and mineralogical changes are presented and preliminary conclusions of possible reaction mechanisms of nickel-bearing minerals are discussed.

Jan 1, 1997

By Oleg Ostrovski

Industrial pyrometallurgical processes in ferrous metallurgy are based on carbothermal reduction of metal oxides. Carbothermal reduction of stable oxides requires high temperatures. Lowtemperature reduction can be implemented by using methane-containing gas with high carbon activity, or by carbothermal reduction under reduced CO partial pressure. Under standard conditions, methane is thermodynamically unstable above 550 °C and decomposes to solid carbon and hydrogen. At appropriate CH4/H2 ratio and temperature, carbon activity in the methane-containing gas phase can be well above unity relative to graphite, which provides favorable thermodynamic conditions for reduction. To maintain these conditions, the rate of reduction/carburisation should be higher than the rate of solid carbon deposition. The paper discusses reduction of pure manganese and chromium oxides at relatively low temperatures, and constraints in reduction of manganese and chromium ores. Reduction of metal oxides by carbon in hydrogen as an alternative use of natural gas is also discussed.

Jan 1, 2014

By Musa Karakus

Ceramic build-ups are synthetic mineral deposits formed in critical locations in or near the throats of inductor units in channel induction furnaces, the preferred melting and holding furnaces used in iron foundries. The build-ups are undesirable because they slow down melt circulation, increase power consumption and cost. and decrease the quality of the metal. This study involved the determination of the mineralogy of build-up samples and the quantitative measurement of phase abundance in those build-ups by cathodoluminescence microscopy. These undesirable deposits usually are hard and dense and contain variable amounts of entrained metallic iron. The non-metallic phases dominantly consist of oxides and silicates of several refractory elements, AI, Mg. Ca, Si, and Fe. Minor amounts of the sulfides of Ca. Mg, Fe and REE elements, especially Ce and La. and the oxides and silicates of Ce and La elements are locally present in the build-ups. The build-up samples were found to be ideally suited for study by cathodoluminescence, which has provided an easy means for rapid re-cognition of the phases present in the build-ups. The phase compositions were determined by electron microprobe analysis. The phases identified and their characteristic cathodoluminescence shown in the ceramic build-up samples were: spinel (bright green, blue-green, and red). forsterite (red and purple), periclase (dark reddish-brown, blue. and orange), corundum (red, blue, orange, and white), anorthite (yellow, yellow-green, blue, and blue-purple), hibonite or calcium hexaluminate (dark green), mullite (dull red-brown), gehlenite (deep blue), silica(dark brown, pink, purple, red. and blue), monticellite (light violet blue and light pale yellow-orange), silicon carbide (orange), oldhamite (bright yellow and orange). Ce-La silicate phases (purple), and glass (orange, dull red, and purple). Non-luminescent phases were: hercynite, Fe-oxides, Ce-La-oxides, Fe-sulfides, and metallic iron.

Jan 1, 1989

The viscosity of high magnesium content FeO-Fe3O4-SiO2-CaO-MgO slags at nickel flash smelting conditions was investigated using a commercial rotational viscometer. The studied parameters were compositions of slag and temperature. The viscosity of these slags was measured as a function of CaO, MgO, SiO2, FeO. Fe3O4 and Fe/SiO2 in temperature range from 1473K to 1723K. These slags contained 5.81 to 10.59 pct MgO, 0 to 10.37 pct CaO, 28.21 to 36.21 pct SiO2, 39.40 to 55.42 pct Fe and 1.1 to 1.5 Fe/SiO2.

Jan 1, 1999

By M. J. Adam

The U.S. Bureau of Mines has investigated the partitioning of complex minerals to simpler phases using sulfidation reactions for selective extraction of mineral values. This report describes research in which thermal processing of the complex Ti-bearing mineral ilmenite (FeTi03) resulted in partitioning of the valuable Ti metal to the simpler compound rutile (TiO2). Samples of ilmenite were blended with elemental S for thermal treatment at various temperatures under controlled atmospheres in an effort to dissociate the Fe from the ilmenite complex. Product characterization revealed that the Fe was partitioned 'from the ilmenite, forming a rim of pyrrhotite/pyrite (FeS/FeS2) on a rut il e core. The products were agate milled and then subjected to cursory magnetic and flotation techniques in an attempt to physically separate the partitioned phases. Partitioning results and phase concentration data are reported relative to thermal treatment variables and physical separation techniques.

Jan 1, 1991

By David T. Hobbs

Large quantities of highly alkaline, radioactive, liquid wastes are stored in underground tanks throughout the Department of Energy complex. These wastes will be pretreated to separate radionuclides and the remaining decontaminated liquid wastes incorporated into solid waste forms for permanent disposal. Significant savings in disposal costs could result by recovering .the sodium as sodium hydroxide for reuse or disposal as nonradioactive waste. Recent testing demonstrated an electrochemical separation process for the recovery of sodium hydroxide from alkaline waste solutions; The separation process uses ion-selective membranes to separate sodium from the bulk of the waste constituents under an applied electrical field. The sodium is recovered as a 10-15 wt % solution of sodium hydroxide. Results of bench-sc3Ie and pilot-scale tests with simulated and radioactive waste solutions are presented.

Jan 1, 1999

By Shi Guan-Yong, Niu Li-Ping, Dou Zhi-He

"In the preset work, the viscosity model (named modified KTH model) proposed by Sichen Du and S. Seetharaman et al and extended by Shu Qi-feng was applied to the ESR slag systems. A correlation to predict the viscosities of CaF 2-(CaO)-Al203 slags using interaction coefficients of different cations in the presence of oz-and viscosity interaction coefficients between oz-and F in the presence of different cations has been developed. The interaction coefficient between oz- and F- in the presence of Al3+ was determined from the experimental data as shown in known literatures. The good agreement between the calculated viscosities and the experimental data in the CaF2-(CaO)-Al203 systems has indicated that this approach can be successfully employed to predict the viscosities of ESR slags.IntroductionReliable viscosities data of high-temperature slag melts are important for the modeling and design of high temperature metallurgical processes. Although a number of experimental measurements have been carried out, the available viscosities data is still scarce compared to the needs of today's technology, especially in the case of complex melts. In process simulations, the needs of viscosity descriptions for complex systems which could enable the extrapolation of the data as functions of temperature and composition is strongly felt today."

Jan 1, 2013

By Osamu Takai, Yoshiki Sato, Nobuhiro Tajima, Hiroyuki Sugimura

"Amorphous carbon thin films doped with nitrogen ( a-C:N) have been synthesized by means of shielded arc ion plating (SAIP). Their electron field emission properties, that is, threshold field strengths for electron emission and maximum emission current densities, were evaluated and compared with those of pure amorphous carbon (a-C) films prepared by the same SAIP apparatus. Among all of the fabricated a-C:N films, the a-C:N films with a N concentration of 23 %, which prepared using Nz arc plasm at a pressure of 1 Pa with applying a sample bias voltage of -100 V, showed the lowest threshold filed of 13.4 V/µm and the highest emission current density of 1.87 µAfcm2 at a field of20 V/µm. These field emission properties of the a-C:N film were much better than those of the a-C films. The best results obtained on the a-C film in this study were the lowest threshold filed of 15.5 V/µm and the highest emission current density of 0.052 µA/cm2 at a field of 20 V /µm. Nitrogen doping to aC was found to be effective for lowering threshold voltage for field emission and for increasing emission current density. The electron field emission characteristics of the a-C:N films depended not only on N concentration but also on chemical bonding state of nitrogen in the a-C:N films. The presence of the ~-C3N4-like phase, which contributes to improve wear resistance of a-C:N as well, distinguished by the NlsXPS peak at 400.5 eV is proved to be crucial in order to enhance field emission properties of a-C:N.IntroductionThere has been much interest in electron field emission from a cold cathode due to its potential applications in vacuum microelectronic devices including field emission displays which are expected as flat panel displays in next generation [l]. It is well known that efficient emission can be rather readily realized using tip-like shape cathodes, e.g., microfabricated three-dimensional electrodes [2], carbon nanotubes [3-5], etc. However, electron emission from planar surfaces is of particular importance since such a type of cathode is· simply fabricated and assembled into microelectronic circuits. Currently, amorphous carbon thin films doped with nitrogen (a-C:N) prepared by plasma processes have attracted attention because their threshold voltages of field emission are relatively low [6]. Among various methods for preparing a-C:N films, the process using arc plasma is of special interest since, in arc plasma, nitrogen is highly activated and new types of carbon nitride phase are expected to be synthesized. However, field emission properties of a-C:N prepared by arc plasma have been studied in less detail compared with that prepared by the other methods such as sputtering."

Jan 1, 2000

By Zhucheng Huang, Ronghai ZHONG, Tao Jiang, Jun ZOU

The method of reduction roasting and magnetic separation of low-grade, micro- fine disseminated refractory iron ore following granulation with coal produced unexpected success. Pellets of iron ore with diameter between 3 and 8mm were granulated with coal, bentonite and water. The raw pellets and reduction products were analyzed by scanning electron microscopy and x-ray diffraction. Results show uniformly distributed coal powders inside the pellets improved the kinetics of the reduction process and accelerated the reduction rate. Reduction time was higher at temperatures below 890℃, which resulted in the formation of substantial amounts of fayalite. When temperature was increased, micro- fine hematite was then quickly reduced to iron metal and the amount of fayalite decreased sharply. When pellets were reduced at 950℃ for 25min, reduction products with 56.73% metallization rate were obtained. After grinding and magnetic separation, a concentrate with 72.18% Fetot was obtained.

Jan 1, 2015

By N. B. Gray, I. F. Taylor

"Gas injection to promote chemical reactions or mixing is a feature of many metallurgical processes. Often the aim of gas injection is to bring about a chemical reaction between the gas and liquid but most of the past physical and mathematical modelling work has ignored the influence of such reactions. In the work reported here, cold model studies have been conducted in which gas reacts with the liquid into which it was injected. The rate of liquid mixing has been measured as an indication of the mechanical energy transfer. It has been found that gas generated chemically within the liquid is significantly less effective at promoting mixing than the equivalent volume of inert gas. The relative ineffectiveness of chemically produced gas is thought to be due to smaller bubble sizes in comparison to the inert gas case. Small bubbles characteristic of chemically generated gas move with low slip velocities relative to the liquid and lead to different turbulence generation mechanisms.IntroductionIn processes such as steelmaking, copper conversion, bath smelting and ladle steel finishing gas is injected into liquid metal where it reacts chemically or simply serves as a source of agitation. An understanding of fluid flow phenomena in such situations is an essential pre-requisite to the calculation of process intensity and the optimisation of vessel productivity. Traditional physical cold modelling approaches to prediction of liquid flow in such situations are now often augmented by the techniques of computational fluid dynamics. Even with the availability of numerical modelling techniques cold physical models continue to have an important role for validation because it is generally difficult to obtain quantitative data from high temperature processes.Almost all previous cold modelling work has been based on the injection of an inert gas into water or some other non-reactive liquid. Such models do not include the significant increase in gas volume inherent in some processes. For example the oxidation of carbon in steelmaking leads to a twofold increase in molar gas flux through the reaction:"

Jan 1, 1996

By Oscar Perales Perez, Atsuo Kasuya, Kazuyuki Tohji, Yoshiaki Umetsu

"The removal of iron and various heavy-metal ions by their incorporation into stable ferrite-type precipitates at 25°C is a promising alternative to clean up large volumes of polluted aqueous effluents. Our research work investigated the conditions to produce magnetite and various M-bearing ferrites (where M: Zn, Cu, Co, Ni, Cd, etc.) directly from aqueous solutions at 25°C by simultaneous control of the oxidizing conditions and pH. The formation of the solids was followed by monit9ring the oxidation-reduction potential (ORP) and rate of proton release during the aerial oxidation of the suspensions at constant pH (contact stage). Only mildly oxidizing conditions, represented by ORP values between -110 mV and -150 mV and a moderate oxidation rate of Fe(II) species were conducive to well-crystallized ferrites at ambient temperature.' It was also found that increasing the Fe/M mole ratio in starting· solutions enhanced the stability ·of the M-bearing ferrites at ambient temperature. When the formation of the ferrite was incomplete, aging of the sludges in their mother liquors at 25°C promoted the crystallinity of the precipitates. The mentioned conditions ·favored the suitable progress of the ferrite-forming reaction involving the oxidation of Fe(II) entities, subsequent hydrolysis of produced Fe(III) species and dehydration of the intermediate:· Furthermore,· the ferrite formation at· low temperature permits the elimination of iron and co-existing heavy metal ions to sufficiently low concentration.In tum, the characterization of the precipitates evidenced their magnetic nature (room-temperature saturation magnetization above 60 emu/g) as well as the effective incorporation of target metal ions into the ferrite structure."

Jan 1, 2000

By E. M. Weenink

A proposed alternative to the conventional zinc extraction processes is the flash reduction of zinc calcines. As part of an overall study of this process, the kinetics of single zinc oxide pellets were investigated. Pellets, compacted from Outokumpu zinc calcine (60.9% zinc, 9.6% iron), were suspended in a flow of CO/CO, mixtures and reduced at temperatures between 1000 and 1200°C and atmospheric pressure. The pellet weight loss with time was recorded and analyzed. It was found that the reduction of calcine pellets (0.9 cm height and 1.36 cm diameter) was controlled by chemical reaction. This paper includes an analysis of the experimental results of two previous investigations of ZnO reduction.

Jan 1, 1992