Search Documents

By Lane White

Refractory gold ores are those from which a significant percentage of the gold cannot be recovered by conventional cyanidation. Historically, roasting has been the primary method for rendering such ores amenable to gold extraction; however, roasting creates environmental problems that are not acceptable in many locations. During the 1980s, consistently strong gold prices drew increasing attention to refractory gold ores, and new processing schemes were commercialized, most prominently aqueous pressure oxidation and more recently bacterial oxidation. Since 1985, pressure oxidation has been incorporated into four plants processing refractory gold ores. A fifth plant is scheduled for start-up in early 1990, and three additional plants are scheduled for production before late 1992. A technical session on treatment of refractory ores was included in the program of `World Gold '89, a Gold Forum on Technology and Practices' held by SME and the AusIMM in Reno, NV, Nov. 5-8, 1989. This article summarizes material from five of the papers presented during the refractory gold session and published in the proceedings of `World Gold '89,' edited by Roshan Bhappu and Rod Harden. The complete proceedings are available from SME Publications Sales, P.O. Box 625002, Littleton, CO 80162-5002 $53.50 for members, $38.50 for student members, and $73.50 list price.

Jan 1, 1990

By M. A. Meyer

Underground mining accidents in the USA in recent times have prompted the Mine Safety and Health Administration (MSHA) to review emergency and tracking systems for underground mines. Several communication and tracking systems are available on the market and various systems have been installed in mines around the world. In addition, MSHA?s standard on Diesel Particulate Matter (DPM) requires mines to comply with the final PEL of 160µg/m3 by May 20, 2008. Barrick Goldstrike Mines Inc., Underground Division, has been in operation since 1995 and an extensive control and monitoring network, and a leaky feeder voice network is in place. Enhancements to the communication and control system are currently being implemented to include a PED emergency notification system, wireless LAN with tracking of personnel and equipment in the mine, and a ventilation control system that will use the tracking information and ventilation data to automate much of the mine ventilation system. Expected benefits from such a system would be enhanced communication with miners, emergency notification, location of miners and equipment, energy savings, improved ventilation control, and improved atmospheric conditions in the mine including reduction of diesel particulate matter (DPM).

Jan 1, 2009

By H. Verakis, M. J. Sapko

The Pittsburgh Research Laboratory (PRL)1 of the National Institute for Occupational Safety and Health (NIOSH) in collaboration with the Mine Safety and Health Administration (MSHA) Technical Support Center has devised a prototype hand-held instrument which can provide a direct assessment of the potential explosibility of a coal and rock dust mixture. Current Federal regulations require that rock dust be applied in all underground areas of a coal mine to mitigate the propagation of a coal dust explosion. To determine compliance with the Federal regulation, mine inspectors collect dust samples from sections of underground coal mines for an MSHA laboratory analysis of incombustible content. However, the laboratory analysis may not be completed for more than a week or two, during which time the mine area from which samples are taken may be inadequately protected. The operation of the Coal Dust Explosibility Meter (CDEM) is based on the difference in optical reflectance between light rock dust and dark coal dust. For a given coal volatility, the optical reflectance of such mixtures is relatively constant at the limit of explosibility, independent of the coal dust particle size. The CDEM is not intended to replace the current MSHA laboratory analysis of coal mine dust samples for incombustible content, but to serve as a supplemental device for enhancing mine safety through improved rock dusting practices.

Jan 1, 2006

By Jayant Khambekar

In a typical mining operation, run-of-mine (ROM) ore is crushed and screened to achieve a desired particle size distribution and then fed to processing equipment for further refining. For an operation to be profit-able, the ore handling system from the mine face to final product loadout must be reliable. However, the handling system components do not always perform as expected and production problems related to material flow occur. These problems include flow stoppages, limited live storage capacities, uncontrollable flow, segregation, spillage and dust emissions. These result in lost production, excessive maintenance, safety and environmental issues, and even structural failures, in some cases. Flow patterns Flow problems and their solutions can be best understood by first learning how bulk solids flow. As bulk solids discharge by gravity from a storage system, primarily two types of flow patterns can develop: funnel flow and mass flow. Figure 1 shows a schematic of these two flow patterns. In funnel flow, only a portion of the material is in motion during discharge, which flows toward the outlet through a channel that forms within the stagnant material. Funnel flow occurs when a hopper is not sufficiently steep and smooth to ensure flow along the walls or when the outlet is not fully effective. In mass flow, all of the material is in motion whenever any is discharged ? there is no stagnant material. Mass flow occurs when the hopper is sufficiently steep and smooth to ensure flow along the hopper walls. Shallow valleys are not permitted and the outlet must be fully effective. A third type of flow pattern, called expanded flow, can develop when a mass flow hopper (or hoppers) is placed beneath a funnel flow hopper or bin. The mass flow hopper is designed to activate a sufficiently large flow channel in the funnel flow hopper to avoid flow problems due to a rathole. The flow pattern in which a bulk solid discharges from a storage system strongly influences the flow problems that may occur in that facility.

Jan 1, 2009

By D. X. Tang, G. Wilson, S. S. Peng

Design and implementation of a roof bolting plan requires reliable geotechnical information of strata, such as rock strength, and locations of interfaces and voids/fractures. The drilling parameters obtained during normal roof bolt installation cycle provide a fast and economic way to gather information on the geological structure within the bolted horizon. The purpose of this research project is to develop a method for identifying the geological features in the mine roof strata based on drilling parameters of roof bolter. The criterion for void/fracture prediction has been developed and proven valid. This paper focuses on the estimation of the strength of roof strata by using drilling parameters. Based on the results of a series of underground and laboratory tests, feed pressure is found to be the most sensitive parameter when the strength of roof strata changes. Moreover, it was also found that both penetration rate and rotation rate have obvious impact on the magnitude of feed pressure. Based on these findings, the criterion for the estimation of roof strata strength has been developed using the relationship among feed pressure, penetration rate and rotation rate and implemented in MRGIS.

Jan 1, 2006

South Africa?s primary electricity supplier, Eskom, provides incentives to reduce power demand during critical times by granting capital through a Demand Side Management programme. DSM encourages the end user to review and optimize energy consuming systems and use capital, provided by Eskom, to purchase or modify the equipment required to achieve a load-shift. As part of the DSM agreement the mine ultimately acquires the capital equipment and benefits from reduced power costs, but in return is required to sustain the load-shift tactic for up to five years. The paper focuses on one DSM tactic, main fan energy management. In this case, reduced air flows during selected peak and off peak periods, results in a substantial reduction in peak power demand. DSM incentives provided capital for automated main fan control as well as improved control of the mine ventilation systems. To examine the work in detail Gold Fields Ltd Driefontein gold mine near Johannesburg was chosen as a case study.

Jan 1, 2009

By A. M. Elmahdy

An amphoteric collector was tested for dolomite removal from phosphate ore. The effects of some operating parameters and their significance on the flotation of dolomite were studied using statistically designed experiments. The parameters studied were impeller speed, pH and collector dosage. Analysis of the results showed that pH is the most significant parameter. Moreover, a concentrate containing 0.53% MgO and ~31.1% P2O5 with a recovery of ~ 90% can be achieved at optimum values of studied parameters, i.e., a pH of 12, an impeller speed of 1,000 rpm and a collector dosage of 2.5 kg/t.

Jan 1, 2007

By Harry R. Price, Bharat Doshi, Awni Qaqish, Abdul-Ghani Mekkaoui, Thaddeus Znoy, Ramesh Shukla

In 1992, a detailed inspection of the Southfield Sewer revealed a reach of approximately 0.8 kilometers in length, located directly below the freeway lanes, which was severely distressed. Failure of this section of the sewer would result in the closing of the busiest roadway in the state as well as the potential backup of sewage into homes and spilling into nearby surface waters. As such, repair of the distressed section required development of a procedure that would not jeopardize the conveyance of flow through the existing sewer nor impede travel on the overlying freeway. Based on these constraints, the DWSD and NTH team developed a repair concept that entailed the mining of a new, 3.05-meter (10-foot) diameter bypass away from the traffic lanes. The new bypass section was connected to the existing sewer, up stream and down stream of the distressed area, using a “top down” construction approach, that required only minimal freeway closures during weekend periods. This paper, prepared jointly by the Owner, Consultant and Contractor will describe existing conditions, design considerations and construction methods.

Jan 1, 2001

By R. J. Robbins

The mechanization of hard rock underground mines offers a large potential for reducing cost, improving efficiency, and increasing profitability. However, in spite of serious efforts by quite a number of equipment developers and mining company initiatives, the industry has achieved little real progress. The task is difficult and the blasting alternative to mechanical excavation is an effective and well-developed method, which continues to improve in spite of its inherent limitations. A large number of machines have been built and tried. Only a few developments have succeeded to make a major impact on underground hard rock mining. It is certain that hard rock mines would be laid out and designed quite differently if the mining engineers knew they had available continuous mechanical excavation machines. In the absence of the machines, mines will be designed for excavation by traditional methods. It is not easy to utilize mechanical excavation in a mine which is designed to operate with normal drill and blast excavation. This is certainly an impediment to machine development. But what if an ore body cannot be mined conventionally, simply because the mining company cannot get permits to satisfy the ever increasing strict EIS requirements of the general public and governmental agencies? This may provide the incentive necessary to develop the equipment that will be needed by a new mining method that will have almost no impact on the environment.

Jan 1, 2001

Syncrude Canada produces a large part of Canada’s crude oil supply. The company processes about 225,000 bbl/day. The oil produced is used for jet and automobile fuel, home heating oil, plastics and other consumer synthetics. Crude oil is produced through a process of mining, extracting and upgrading bitumen. A rich supply of bitumen is contained in the Athabasca oil sands deposit in northern Alberta. Tailings from the bitumen processing are sent to a settling basin.

Jan 1, 2000

By P. R. Dugan

Sulfur removal from high sulfur coal has several objectives including: a) reduction of the atmospheric load that contributes to the problem of acid precipitation; b) reduction of ash, which contributes to decreased energy transfer in boilers, as well as ash disposal; and c) alleviation of the social and economic dislocations reluted to uneven geographical distribution of sulfur in coal reserves. Cost in relation to the value of refined coal will govern the development of an emerging coal refining industry. Estimation of the premium paid by power companies for coal with a low sulfur content is a good estimate of the value that will be added as the result of refining. Estimates of premiums paid in 1984 are $28.65/t ($26 per st) for reduction of total sulfur from 3’% to 1% S and greater than $28.65/t ($26 per st) for removal below 1% sulfur.

Jan 8, 1987

By D. Craig Camp

conditions. The soils included 65 m of rock not exceeding an unconfined compressive strength (UCS) of 200 kgf/cm2, 130 meters of soft clay, silt, and sand not exceeding 30standard penetration test SPT blows per 300 mm, and 220 m of rock ranging between an UCS of 400-600 kgf/cm2. The river crossing, utilizing 1778 mm OD x 19 mm wall x600 mm steel casing pipe without intermediate jacking stations, was part of a seven kilometer liquefied natural gas (LNG) transmission line in South Korea. This 440-m, 1,442-ft, river crossing was microtunneled through three different ground conditions and completed in just over three months. The crossing was achieved with an average of 25 m of ground cover and 15 m of water cover. The Kwang Yang River Crossing was part of a 7 km liquefied natural gas pipeline project for POSCO, a Korean steel producer. The microtunneling machine was custom built for this project. The microtunneling machine selected for this project was tooled with 7 button bits and 2 roller bits. None of the cutter bits were replaced during the drive. Inside the machine, before the spoils laden slurry was pump back to the surface, it would pass through an independent cone crusher. The crusher is placed in the slurry flow to make sure that none of the spoils are so large as to stop the return flow of the slurry. An additional requirement was for the inclusion of a compressed air lock. The air lock was required in the event that the cutter tools required replacement. The cutters were back loaded so that the workers would have access to change the cutters in the event of cutter failure or wear out. No intermediate jacking stations were installed for the drive. The soils included 65 meters of rock not exceeding an unconfined compressive strength (UCS) of 200 kgf/cm2 with production averaging between 7 and 20 mm/minute. The second zone contained 130 meters of soft clay, silt, and sand not exceeding 30 standard penetration test (SPT) blows per 300 mm with production averaging between 80 and 180 mm/minute. The third zone contained 220 m of rock ranging between an UCS of 400-600 kgf/cm2 with production averaging between 7 and20 mm/minute. The steel casing pipe was 1778 mm OD x 19 mm wall x 6000 mm long. The project profile, see Figure 1, shows the soil conditions. The hand written numbers locate just above the pipeline are the production dates. The circled numbers are the 10 pipe joint increments. The project required 74 pieces of pipe to span the440 m drive. Figure 2 and Figure 3 are the jacking information. Figure 3 is a continuation of the information from Figure 2. The top section of the graph is the jacking force. The jacking

Jan 1, 2001

By Dermot Winters

The Surface Mining Control and Reclamation Act (SMCRA, or the Act) was enacted on August 3, 1977. The Act was written, in part, to put an end to uneven environmental standards and to establish minimum national standards. Certainly, one of the motivating factors for passage of the Act was the success of the Federal Coal Mining Health and Safety Act of 1969 in reducing deaths and injuries in the coal industry nationwide. Section 516 (b) (1) of the Act requires *that subsidence be prevented from causing material damage to the extent technologically and economically feasible except in those instances where the mining technology requires planned subsidence in a predictable and controlled manner. Section 516 (c) of the Act authorizes the regulatory authority to suspend underground mining if there is imminent danger to inhabitants of urbanized areas, cities, towns, and communities. On December 13, 1977, the interim program, which applies a portion of the performance standards of the Act, was promulgated. Then on September 18, 1978, the proposed permanent program was published for public comment. Finally, on March 13, 1979, the final permanent program was promulgated and the States were given a period of time to submit their programs for approval.

Jan 1, 1986

By S. Möllerherm

"The evaluation of data and information provided by the existing traditional indicators in sustainability assessments is most important. Therefore the Institute of Mining Engineering I from the RWTH Aachen University developed indicators and an assessment system for the mineral raw materials industry on operation, company and sector level on behalf of the Federal Ministry of Economics and Labour (Bundesministerium für Wirtschaft und Arbeit, BMWA) and the Federal Institute for Geosciences and Natural Resources (Bundesanstalt für Geowissenschaften und Rohstoffe, BGR). In the course of the development of indicators for the raw materials industry quality indicators on different levels of the sustainability assessment procedure have been identified and developed. The following paper describes some of the results focussing on the development and integration of quality indicators into sustainability assessment systems."

Jan 1, 2005

By Michael Stanwood

Project feasibility no longer involves just technical and economic viability-today's feasibility study must include environmental, regulatory, and political considerations as well. While the US now appears at least somewhat committed to developing synthetic fuels, including oil shale, it is the environmental issues, rules, regulations, and guidelines that will play the major role in determining the timing, magnitude, and overall scope of synfuel development in the coming years. The key environmental obstacle affecting oil shale development is uncertainty. Although oil shale may be the most environmentally studied "new" technology in the world, little is known with much degree of certainty about potential environmental consequences of one full-scale commercial facility, or the effects of a massive development effort in a relatively pristine and sparsely populated area. Other primary environmental uncertainties include: • Environmental compliance costs and their effects on investment decisions; • The reliability and acceptability of anticipated pollution control technologies; and • The confusing, time-consuming environmental regulatory framework, which requires more than 100 permits, clearances, and reviews before development occurs. This discussion will focus on the latter uncertainty, and will describe he current status of potential constraints to oil shale industry development in five areas: water availability; water quality degradation; air quality degradation; reclamation and spent shale disposal; and community impacts.

Jan 1, 1981

By Bradford F. Townsend, Colin R. Speers

INTRODUCTION This is the first in a series of papers addressing practical tunnel lining design. The format for this and future papers is to present a particular topic and support the presentation of the guidelines by the practical application of a case history. The primary intent is to provide guidelines for the geotechnical and structural design of tunnels where the tunnel size and/or ground conditions dictates that systematic support of the excavation is required following each increment of excavation. This method of tunneling is commonly referred to as Sequential Excavation and Support(SES) and is also commonly termed the New Austrian Tunneling Method (NATM) The authors developed the design guidelines from experience gained over the past two decades during the design and construction of several major railway, highway and water-transfer tunnel projects in Africa and Asia. During this time it has been possible to compare the performance of the as-constructed structures to the predicted performance as given by the design process. Excavation was typically carried out in widely varying ground conditions (weak-bedded rock, jointed hard rock, and soil-like poorly cemented rock with groundwater). It is therefore intended that the design guidelines could be applied, in general terms at least, to any tunnel excavated in any ground mass condition with any ground material type (hard rock, soft rock, bedded rock, soft ground, and soil) with or without ground water. This first paper is an introductory paper that defines the scope and a brief outline of the design issues that may be presented in detail in later papers. What is design? It may be thought of as any rational/verifiable/justifiable process whereby a concept is transformed into information that can be used to bring the concept to reality. In the case of a civil structure, design may be defined as that process, which is documented and can be audited, that determines information such as the shape (form) of the structure, the dimensions (size) of the structure, the thickness and strength of structural members that comprise the structure, etc. This information can be used to compute the time, money and resources required for

Jan 1, 2005

By R. Karl Zipf

Highwall mining is an important surface coal mining method, and it may account for approximately 4% of total U.S. coal production. Highwall stability is the major ground control related safety concern. Ground control plans for highwall mining should specify hole width, web pillar width, barrier pillar width and number of holes between barriers. This paper offers simple design charts for these parameters aimed at providing “ball park” checks. Web pillars containing pre-existing auger holes are analyzed and a design chart for estimating their minimum width is also presented. Finally, close proximity multiple seam highwall mining, which may have caused several serious highwall failures, is analyzed. Web and barrier pillar recommendations for this special situation are presented.

Jan 1, 2005

By N. A. Abdel-Khalek

The amenability of carbonate separation from a sedimentary phosphate ore using a bioflotation process was studied. Two types of bacteria were chosen for this study. The experiments were performed using oleic acid as collector. The flotation experiments were carried out using statistical designs for optimizing the main operating parameters. A concentrate containing 0.78% MgO and 30.15% P2O5 with a recovery of 92.31% was obtained from a feed containing about 2.45% MgO and 27% P2O5. These specifications could not be obtained using conventional flotation experiments under similar conditions in the absence of bacteria. Measurements of zeta potential, adsorption of bacteria and collector, as well as froth power, were performed to explain the role of microorganisms in the surface modification of both dolomite and phosphate and in their interaction with the collector.

Jan 1, 2009

By Thomas P. Kwiatkowski, Joginder S. Bhore, Christopher D. Orlandi, Jose Velez

Three case histories of successful TBM tunneling for New York City Water Tunnel No. 3 are presented. The tunnels, costing about one billion dollars total, are the 5-milelong, 18'-11" OD Brooklyn Tunnel; the 5-mile long, 23'-2" OD Queens Tunnel, and the9-mile long, 12'-4" OD Manhattan Tunnel. The three tunnels are the first major tunnels constructed in New York City rock utilizing the TBM method of construction. This paper describes and compares the three tunnel projects in terms of geology, construction methods, TBM’s, rock and groundwater behavior, rates of advance and other performance data, and challenges and solutions encountered during the projects.

Jan 1, 2007

The largest investment in mining equipment in Caterpillar?s history ? The F series mechanical and electrical drive trucks ? is rapidly advancing. Caterpillar showcased the 793F and 797F mechanical drive trucks and the 795F ac electric drive truck at MinExpo in 2008 and have continued testing since then. The 793F and the 797F have accumulated more than 75,000 hours of field testing and have proven their performance capabilities and their durability. The new Cat C175 engine that powers them has racked up 130,000 hours of field testing in mining trucks and more than 120,000 hours in power systems. Because of the success of these field-follow programs, the 793F is targeted to go into full production within a few months and the 797F late this year. Caterpillar engineers have been testing two 795F ac prototypes at the Tucson Proving Grounds in Arizona. The development program has provided input for the construction of a new 795F ac in Decatur, IL. The new truck recently shipped to a copper mine in North America where it will serve as the first field-follow 795F ac as it works at the mine. The 313-t- (345-st-) capacity 795F ac will enter a new size class for Caterpillar, and, as a result, the primary focus of the Caterpillar ac electric program has been on the 795F ac. The commercial launch date will be defined as the field-follow program progresses. ?It?s fitting that soon after producing the 50,000th Cat off-highway truck, we are now shipping our first ultra-class ac electric drive truck to a mine,? said Chris Curfman, president of Caterpillar Global Mining. ?Our new trucks further solidify our position as the one manufacturer to provide unparalleled options and unmatched customer support.?

Jan 1, 2009