Search Documents

By Ryan C. Stephan, Christopher Mark

"Some of the weakest roof in United States coal mines is found in the Illinois Basin. Historically, the Illinois Basin has also suffered from high rates of unplanned roof falls and rock fall injuries. During the past decade, however, roof fall and rock fall injury rates have fallen dramatically, and are now lower than the national average. Several technologies are responsible for the improvement. Roof screen was rarely used ten years ago, but a number of mines now use it on a regular basis to prevent rock falls and rock fall injuries. Other roof skin control fixtures and work practices have contributed as well.The reduction in roof falls is also directly attributed to enhanced intrinsic roof support. Stiffer primary bolting patterns have reduced the magnitude of roof spalling and roof sag. They have also helped create a more intact beam that is able to be suspended from longer cable bolts. Cable bolt design methodology has also contributed to this reduction in roof falls. Some early cable bolt applications were unsuccessful because they employed as few as two cable bolts per intersection. This paper describes a methodology for estimating rock loads for support design.ROOF FALL TRENDS IN THE ILLINOIS BASINAlthough the Illinois Basin has a long history of poor roof conditions and high rates of unplanned roof falls and rock fall injuries, recent data indicates a change in the trend. Roof fall rates are determined by dividing the total number of non-injury roof falls by the total number of hours worked underground. The data is considered for 200,000-man hours. While the Illinois Basin was once a coalfield experiencing roof falls at nearly twice the national average, it is now at or below the national rate. Figure 1 indicates the trend over the past 20 years. In 2008, the Illinois Basin mines experienced 5.06 roof falls every 200,000-man-hours, compared to only 0.75 in 2018.There has also been a significant reduction in the rate of rock fall injuries in the Illinois Basin coal mines, as shown in Figure 2. In 2008 there were 1.48 rock fall injuries every 200,000-man-hours, compared to only 0.43 in 2018.ILLINOIS BASIN COAL ROOF GEOLOGYThe roof rock in the Illinois Basin has been studied in the past to understand the primary causes of roof failures (Molinda et al., 2008; Thompson, 2010; Molinda and Mark, 2010). Rusnak and Mark (2000) evaluated 10,000 laboratory strength tests from 800 rock units and concluded that for shale, siltstone, and sandstone, the strength of the Illinois Basin variety was less than half that of the same rock types in Central Appalachia (Figure 3). A study of Coal Mine Roof Rating (CMRR) measurements in more than 200 US coal mines also found that weak roof was predominant in the Illinois Basin (Mark and Molinda, 2005)."

Jan 1, 2019

By A. Thatcher, C. Day, C. Meyer

The purpose of this paper is to provide general information about the bioaccessibility of metals and specific information about the use of bioaccessibility in risk assessments (human health risk assessments [HHRA] or ecological risk assessments [ERA]) and a list of sites where regulatory agencies have approved the use of bioaccessibility data in risk assessment. The memorandum also cites current U.S. Environmental Protection Agency (USEPA) guidance as well as state specific guidance where applicable. BRIEF HISTORY OF METAL BIOACCESSIBILITY TESTING AND METHODS The bioaccessible fraction of a constituent is that fraction that dissolves or desorbs from its matrix (e.g., soil) in the gastrointestinal tract and is available for absorption (USEPA 2007a; ITRC 2011; ITRC 2017). This is different from the bioavailable fraction, which is the percentage of the amount of an element that an organism is exposed to that is absorbed by that organism during a given time under defined conditions (USEPA 2007a). The bioaccessibility factor is the percentage of a metal that is potentially available for absorption and, therefore, is a conservative estimate of the bioavailable fraction since all that is available for absorption may not ultimately be absorbed into the organism’s system. Currently, there are two main techniques for estimating bioavailability of metals within a medium: in vivo animal studies (time-consuming and often cost-prohibitive), and in vitro tests that simulate human, or animal digestion in a laboratory setting. In vitro and in vivo test methods and protocols have been extensively evaluated by numerous researchers (Ruby et al. 1996; Rodriguez and Basta 1999; Sips et al. 1998; Sips et al. 2001; Molly et al 1993; Oomen et al 2002; Kelley et al. 2002; Oomen et al. 2003; Furman et al. 2006; Drexler and Brattin 2007; Basta et al. 2007; Wragg et al. 2009; Wragg et al. 2011; Chaney et al. 2011; Bradham et al. 2015; Bradham et al. 2018). The most recent scientific literature demonstrates that protocols used to estimate the bioavailability of metals to mammals also predict bioavailability of metals to birds as well (Beyer et al., 2016).

Jan 1, 2019

By T. Bajpayee, J. Ellenberger

Microseismic monitoring and evaluation is one aspect of the National Institute for Occupational Safety and Health (NIOSH) research program. Roof falls are often preceded by a period of elevated microseismic activity, but not all periods of elevated activity result in a roof fall, nor do all roof falls occur after some amount of elevated activity. The objective of this study is to review periods of elevated microseismic activity and determine whether fracture activity rate can be used to anticipate the initiation of roof falls. The study was carried out at an underground limestone mine where major roof falls are associated with excessive horizontal stress. The progression of roof falls was detected by the microseismic signature produced by the rock falling from the mine roof onto the mine floor, which is termed a roof fall impact event. A total of nine elevated fracture activity periods that resulted in seven major roof falls were examined. It was observed that elevated fracture activity preceded the initial roof fall impact event in three out of four major roof falls. The initial impact event was not identified for the remaining three roof falls. Fracture event rates were analyzed and a roof fall alarm trigger of five fracture events in a ten minute time period was established for this test case. The fall alarm trigger was tested against six of the elevated activity periods. Four roof falls occurred in the six periods of elevated activity, and two would have triggered the alarm before the roof fall occurred, while two false alarms were generated. The results show that limited success would have been achieved by the microseismic system as a roof fall alarm trigger. However, the trigger would have been successful at warning of the onset of elevated activity, allowing mine employees to respond appropriately. The study highlighted some issues with implementing such a system in an operating mine, including the need for real time identification of fracture related microseismic signals among mining induced signals, and accurate location and identification of fracture clustering.

Jan 1, 2007

Basic parameters affecting the stability of foams have been studied. We used the thin film pressure balance (TFPB) technique of Scheludko and Exerowa (1959) to measure the surface forces in foam films stabilized with various frothers such as pentanol, octanol, MIBC, and PPG. The results were compared with the froth stabilities measured using the shake tests and the film elasticity calculated using the model developed by Wang and Yoon (2006). It was found that the froth stability is controlled by both film elasticity and surface forces (or disjoining pressure), the relative contributions from each changing with frother concentration and type.

Jan 1, 2006

By Qinghua Tian, Zhipeng Xu, Dong Li, Xueyi Guo, Liu Zhu

A possible process for extracting tellurium and antimony from a residue generated in alkaline sulfide leaching of telluriumbearing alkaline skimming slag was proposed. The central composite design was employed to define the optimal leaching conditions for tellurium and antimony extractions from the residue sample. Using a 23 factorial matrix, the best performance for tellurium and antimony extractions (96.36% and 99.64%) were obtained at 175 g L−1 Na2S concentration for 80 °C during 60 min. The notable degree for influencing tellurium and antimony extractions was leaching temperature, Na2S concentration, and leaching time. The analysis of variance results indicated that the regression model was significant and suitable to be used for the optimization of independent variables within the range. The model was validated under optimal operating conditions based on the experimental design results. Antimony and tellurium in the leach liquor were separated and recovered by H2O2 oxidation followed by Na2S-Na2SO3 reduction. 98.93% of antimony was precipitated selectively during H2O2 oxidation, while 95.06% of tellurium was precipitated during Na2S-Na2SO3 reduction. NaSb(OH)6 and elemental tellurium was obtained as the product.

By J. I. Schoenherr, G. Schubert, F. Demczenko

The currently known and used plastics and rubber recycling or sorting processes cannot be applied efficiently and economically due to large amounts of fine bulky materials (<3 mm). These wastes are mostly given to specialized landfill sites. Starting out from classical and traditional beneficiation processes a new research project was initiated to work on certain new ways to efficiently separate plastic material mixes. First basic results show that the use of new and improved thermal beneficiation methods is a great implementation in the field of plastics separation. The results can be further increased by a suitable combination with other methods as well. This leads to high-quality and almost pure separated plastics and rubber products, easy to sell on recycling product markets.

Jan 1, 2002

By Ching-Liu Wu, John Hawley, Andrew H. Liu, James Chai

The Hatch Mott MacDonald/Bechtel Joint Venture team is designer and construction manager for the 5.25-mile Tunnel Segment of the overall 16-mile Silicon ValleyRapid Transit Project, which extends the existing Bay Area Rapid Transit (BART) system southward from Fremont to San Jose. The Tunnel Segment includes twin boredtunnels, mined cross passages, and three deep station excavations situated in highlyvariable ground, high ground water table, and a dense urban setting with high-risebuildings adjacent to the largest excavation. This paper will discuss design challengesthat have arisen with the excavations and the proposed solutions.

Jan 1, 2007

Where space is limited, as it is throughout most of the northeastern United States, new construction either takes place high above street level, or below it. In Lower Manhattan, NY both kinds of expansion can be found in abundance. That is good news for the nearly 200 attendees at the George A. Fox Conference, presented by the Underground Construction Association (UCA) of SME at the Graduate Center, City University of New York, on Jan. 30. Among the many projects taking place in Lower Manhattan?s massive trans-formation process, are expansions to the city?s vast underground network of subways and other tunnels. ?New Yorkers either live on the ground or below it,? said keynote speaker Charles J. Maikish while explaining how an attempt to build above street level walkways never caught on in the city. Maikish is the executive director of the Lower Manhattan Construction Command Center. His job is to oversee the $22 billion project that will transform the island by 2010. From the construction of Freedom Tower at the site of the fallen World Trade Center buildings, to the expansion of the Second Avenue Subway, the extension of the East Side Access, No. 7 line, the new trans-Hudson line and numerous waterway tunnel expansions, including City Water Tunnel No. 3, the task Maikish is charged with is a huge one. He is primarily responsible for coordinating the scheduling and staging of the overall rebuilding plan, along with the day-to-day coordination of construction work down-town. He places particular focus on mitigating impacts on the environment and mobility, maintaining and improving access and alleviating congestion of any kind related to construction. At the time of the Fox Conference, there were 59 projects under way in Manhattan. All of those projects need things like concrete and steel delivered to sites in very tight working environments. And some need the equipment in even tighter spaces. ?This is not just about the recovery of Lower Manhat-tan (from the 2001 terrorist attacks) but this is a plan to restore it and to maintain its integrity,? said Maikish. ?I think that is the appropriate response to the terrorist attacks.? When Freedom Tower is completed, it will stand 541 m (1,776 ft) about the skyline. That will be a strong statement to the world about America?s strength. But it is the work that takes place much lower that was of interest to the conference attendees. On this respect, Maikish said Manhattan?s efforts below ground aim to provide relief to the city?s street level congestion and to make sure Manhattan ? already essential to the economy of the United States and the world ? stays current by upgrading the existing telecommunications and technological network while also allowing room for growth in that area.

Jan 1, 2007

By Steve Kral

Borates are minerals that contain boron. Trace amounts exist in rocks, soil, water and people. Boron-containing ores are rare and U.S. Borax, a subsidiary of Rio Tinto Borax, controls one of the world’s two world-class borate deposits. Through its global systems of mines, refineries, ports, sales offices and distribution centers, the company supplies nearly 45 percent of the world’s demand for borates. Borax has been mining borates in California for more than a century. This year the company celebrated 131 years of continuous business in the Golden State and 76 years at its operations in Boron, the site of California’s largest openpit mine. It also has mines and refineries in Argentina, refineries and ship-ping facilities in Europe and technical staff in the United States, North and South America, Europe and Asia Pacific. So, with the 130±years of borate mining and processing experience behind it as well as its global marketing and distribution centers, there is very little that Borax does not know about borates.

Jan 1, 2003

By D. Potter

In 1990, Freeport Exploration began regional reconnaissance exploration programs in Irian Jaya, the easternmost province of the republic of Indonesia (Fig. 1). Irian Jaya occupies the western half of the island of New Guinea. Freeport was awarded an initial contract of work that totaled 2.6 million hm2 (6.4 million acres). The company was subsequently awarded additional concessions that added 1 million hm2 (2.5 million acres). The concessions require work commitments and periodic relinquishments. Due to these relinquishments, Freeport’s current land position totals 1.9 million hm2 (4.7 million acres). Freeport began the exploration program to locate additional Grasberg deposits, the largest deposit in the Ertsberg district. But the company recognized that other types of deposits could be present in the largely unexplored area of Irian Jaya.

Jan 1, 1999

By Christopher J. Bise

INTRODUCTION The transportation of men, supplies, and mined material from an underground operation is the connecting link between the mine plant and the surface plant. Unless the mine is accessed by a drift or adit, some form of hoisting system is necessary for slopes or shafts. This chapter will deal with the selection of wire ropes and hoists, two of the most important consider¬ations when designing a hoisting system for an under¬ground mine. WIRE ROPES General A wire rope is designed to transmit forces longitudi¬nally along its axis. Wire rope is used in a variety of mining applications because of its flexibility, high ten¬sile strength, and dependability. Shaft hoisting ropes and principal slope haulage ropes are usually custom-¬built; however, proper rope selection for slushers, car spotters, etc. should not be overlooked. Wire ropes for shafts and slopes, since they represent the life line for the mines, should be of the very highest quality improved plow steel. This quality is necessary to deal with the conditions of loading, winding, vibration, abrasion, and corrosion. Tables I and 2 display the specifications for the typical wire ropes used for mine haulage applications. The 6 x 19-class haulage rope is used for most hoisting where abrasion is not critical. On the other hand, where abrasion is critical, such as a slope application, 6 X 7-class haulage ropes are preferred. For other mining applications, manufactur¬ers&apos; handbooks should be consulted. Selection The selection of a wire rope for a mining situation consists of simply applying appropriate safety factors to a calculated maximum rope pull and comparing the result to the listed breaking strength of the rope under consideration. Table 3 can be used for determin¬ing the minimum factors of safety for wire ropes. To determine the maximum rope pull, the following quantities must be known: the rope weight in pounds (x), the conveyance weight in pounds (y), and the weight in pounds of the load in the conveyance (z). These values are used to calculate the load due to gravity, the load due to conveyance friction, and the load due to rope friction. When these loads are added together, as shown in Eq. 1, the maximum (static) rope pull (RPS) can be derived:

Jan 1, 1986

By Ray Hutton, Darrell Liebno, Taro Nonaka

Background Population growth and increasingly stringent regulatory controls on water quality across North America have resulted in municipal governments investing heavily in infrastructure to control what are known as Combined Sewer Overflows (CSOs).These are events which occur when combined sewers exceed their conveyance capacity during periods of heavy rainfall or snowmelt. The city of Atlanta, Georgia is one such municipality; with a population of over450,000 within city limits and a sewer system servicing 1.2 million including adjacent jurisdictions, the City of Atlanta has a Combined Sewer System (CSS) encompassing approximately 15% of its total 3,540 km (2,200 miles) of sewers. Atlanta’s CSO discharges to local watercourses began to draw fire from environmental groups in the1980s. As a result, in the early 1990s, the City constructed a series of CSO control facilities which provided screening and chlorination at seven CSO discharge points across the CSS watershed. Unfortunately, these facilities were not capable of handling all of the overflows generated due to heavy storm events; frequently, untreated water was bypassed around the treatment facilities. The federal Environmental Protection Agency (EPA) deemed that water quality standards were being violated by these discharges, and a suit was brought against the City to force a higher standard of compliance. As a result, the City entered into a federal Consent Decree which would bring CSOs into compliance with federal standards by 2007. A critical component of this plan was the design and construction of the West Area CSO Tunnels and Pumping Station. In February 2003 the City’s Department of Watershed Management retained the services of Jordan Jones & Goulding/Hatch Mott MacDonald/Delon Hampton Associates (JDH Joint Venture) to design and provide construction management ser-vices for the project, which was designed to capture combined sewage from three of the City’s existing CSO facilities on the northern end of the CSS watershed. The design consisted of two connected tunnels which would convey the wastewater originating from the North Avenue, Clear Creek, and Tanyard Creek CSO facilities to a submersible wet well pumping station located at the R.M. Clayton Water Reclamation Center (WRC). Since the majority of the effluent stream consisted of storm water, the City elected to design and construct a separate treatment plant. This plant was designed under a separate contract, and is currently under construction.

Jan 1, 2007

By J. Swanepoel, J. H. van Laar, J. C. Vosloo, W. A. Pelser

Deep-level underground mining costs in South Africa are continuously rising due to the increased depth at which gold is being mined, resulting in a rise in virgin rock temperature and an increase in cooling requirements. Therefore, mines must evaluate various ventilation and cooling optimisation projects required to be implemented throughout their life of mine (LOM). This study develops a method to identify and prioritise large capital expenditure (CAPEX) underground environmental improvement projects, to improve thermal comfort underground. The solution presents a ‘multi-criteria decision-making’ (MCDM) process, incorporating the ‘analytic hierarchy process’ (AHP) and the ‘technique for order performance by similarity to ideal solution’ (TOPSIS) into the method to provide for scientific decision-making. These projects are evaluated based on four criteria, namely project risk, the impact on the underground thermal comfort, cost, and implementation time. This study’s solution uses ventilation simulations to determine the impact of the projects on the underground environment. The identification and evaluation of an environmental improvement project to best suit the current economic climate, while improving underground conditions and decreasing the safety risk is an essential aspect of the solution developed in this study. The method was implemented on a mechanised deep-level underground mine and showed that surface refrigeration is the most suitable alternative, which was implemented at the case study mine as validation of the developed solution. The study proves that the MCDM method is an adequate solution to incorporate subjective criteria into the decision-making process, resulting in a scientific and structured approach to making significant and complex decisions.

Feb 17, 2023

By D. Kwietnewski

With all of the unknowns associated with tunnel construction, how does a contractor choose a roadheader? This paper presents a review of several models of roadheaders being used in today?s tunnel projects. The features of different models of roadheaders are presented and compared. Roadheader size and cutter power generally determine which roadheader is best for a particular job. We will also present a model for matching features of the roadheader to the anticipated ground conditions such that the most efficient machine is selected for the project.

Jan 1, 2011

By J. D. Morgan

The US economy continued to grow steadily in 1988, reaching an annual rate of $5 trillion in the last quarter (US trillion = 1012). The value of domestically processed mineral-based materi¬als rose 20% to $300 billion (US billion 109). The value of metals produced from US ores rose 40% to more than $10 billion, industrial minerals rose 6%&apos; to $20 billion, and recycled scrap more than doubled to $10 billion. Increasing economic activity stimulated metal prices. Yearly lows and highs were 95 cents and $1.68 for copper, 52 cents, and $1.30 for aluminum, 34 cents and 42 cents for lead, and 43 cents and 75 cents for zinc. A number of mining and metal companies experienced significantly increased profitability. Consumer demand strongly affects mining because the US economy is relatively saturated with long-lived products. Consumer, mortgage, and Federal debt continued to rise. About 246 million US citizens already possess 170 million licensed motor vehicles and 100 million dwelling units. New car production remained at the 1987 level of 7.1 million units. Truck and bus production, however, rose 7% to 4.1 million units. New housing starts fell 7% to 1.5 million units. Imports supplied a significant proportion of total US consumption of several important mineral materials. By year-end, imports of crude and refined petroleum exceeded domestic crude oil production. Such imports cost $42 billion. Imports of nonfuel mineral-based materials were valued at $44 billion and exports at $35 billion. The US and Canada-the world&apos;s two largest trading partners-consummated a historic free trade agreement. In February, President Reagan transferred responsibility for stockpiling strategic and critical materials to the Secretary of Defense. And, in July, the GSA group that bought, stored, rotated, and sold stockpiled materials was transferred to the Defense Department&apos;s Defense Logistics Agency. Concern about apartheid in South Africa continued, resulting in increasing attention to chromium, manganese, platinum-group metals, cobalt, vanadium, and gold. The Defense Production Act, authorizing priorities and allocations, supply expansions, voluntary agreements, and the National Defense Executive Reserve, was amended to include provisions for averting harm to national security from foreign takeovers. The DPAct, in effect through September 1989, is now up for further extension. Under the Act, the US Bureau of Mines maintains the Emergency Minerals Administration. During the year, consultations were held with Canada to strengthen the North American Defense Industrial Base. Coal production, 60% from open pits, rose 5% to 870 Mt (960 million st). Nearly four-fifths was burned to generate 57% of US electricity. Exports included 56 Mt (62 million st) of metallur- gical coal and 29 Mt (32 million st) of steam coal, with a total value of $4 billion. Domestic petroleum produc¬tion fell 2% to 574 hm3 (3.6 billion bbl). Uranium mining, including recovery from phosphates, was unchanged at 5.9 kt (6500 st). Nonfuel minerals Major metals Raw steel production-a major con¬sumer of many minerals-rose 14% to 92 Mt (102 million st). Domestic iron ore production rose 25% to 59 Mt (65 million st), about 96% pelletized. Net imports rose 37% to 16 Mt (18 million st). Raw steelmaking capacity of 102 Mt (112 million st) was unchanged. Voluntary Restraint Agreements with 21 steel exporting nations limited im¬port penetration to about 20% of the domestic market. Domestic producers of bulk ferroal¬loys of chromium, manganese, and sili¬con operated at about 75% of capacity. The US mined no manganese or chro-

Jan 1, 1989

The use of coal as a fuel causes air, pollution in; a number of different forms, and in nearly all stages of its, handling, preparation, storage, use and-disposal of its residue. First let us consider the handling of coal. As shipped, particularly to large utilities, it is run-of-mine bituminous made up of large chunks as well as pulverized particles. Because it &apos;is in an open car or barge, it is subject to the action o winds and the small particles may be blown around adding to the-particulate load in the atmosphere. Mien un¬loaded from the barge or car, there is again an opportunity for the wind to blow the fine particles around. All of us I am sure have seen a barge at the dock of a utility plant being unloaded by a clamshell bucket. This, after grabbing its load from the barge, lifts it some 60 or 70 feet and, then drops it on a conveyor, which carries the coal to a storage area.

Jan 1, 1964

By G. S. S. Raman, M. S. Klima

Coal refuse slurries stored in tailings impoundments can potentially lead to environmental concerns such as effluent seepage, property devaluation, and in extreme cases, dam failures. Pressure filtration offers an opportunity to reduce the impoundment requirements by providing significantly drier solids. A full-factorial design was used to study the effects of temperature and pH on dewatering a refuse slurry obtained from a coal preparation facility in Pennsylvania, USA. The experimental results indicated a strong effect of temperature on cake moisture as the cake moisture after about 2800 s was 22% at 43 °C and only 36% at 10 °C for tests conducted at pH 3. ANOVA results confirmed the statistical significance of pH, temperature, and their interaction effect. Also, the results showed no significant differences between the tests conducted near neutral and alkaline pH values at low and ambient temperatures. On the other hand, Tukey's test indicated higher reductions in cake moisture at higher temperatures for lower pH values. This study affirms the need to monitor and control the pressure filtration process as throughput could significantly vary with changes in temperature and slurry conditions.

Jun 17, 2019

By S. S. Peng, C. T. Holland

Mountain Top Removal (MTR) mining started in West Virginia nearly thirty years ago. This surface mining method can extract multiple coal seams as thin as a few inches thick with total recovery and minimum rock dilution in very steep mountainous terrain. It is highly efficient even if coal seams are in close proximity and small in aerial extent. Consequently, MTR has been widely used in the Central Appalachian Coalfield (mainly Kentucky, Tennessee, Virginia and West Virginia) for the past thirty years with great success. In that respect, there has been no demand for research and little scientific research has been performed to investigate its impacts on the surroundings in the history of MTR mining. However, in the past two years the debate over the MTR mining has grown quickly and in times become very intensely. This paper describes chronologically the issues raised by various parties, legal actions, its impacts on mining permit application and research projects developed to address the issues.

Jan 1, 2000

By Claude Deveau, Stephen R. Young

Introduction Tanco History Tanco is sometimes known as the Bernic Lake Mine. It is located about 180 km east-northeast of Winnipeg close to the Manitoba-Ontario boundary. Tanco operates an underground mine employing ramp access, room and pillar mining and shaft hoisting for the production of tantalum, lithium and cesium minerals. Tantalum recovery employs conventional gravity and centrifugal concentration methods along with a flotation process which recovers ultra-fine tantalum. All tantalum concentrates are shipped to Cabot Supermetals, Boyertown, Pa., for the production of tantalum chemicals and metals. Tanco also produces lithium products from spodumene ore. The lithium concentrates from Tanco are shipped worldwide for use in ceramics, specialty glass and mold powders. Cesium processing involves the dry grinding of pollucite as feed stock to the on-site chemical plant dedicated to the production of cesium formate, a high density drilling fluid. Tantalum milling operations commenced in 1969. In the early years of the operation, feed grades were three to four times as high as they are today. Coarse-grained tantalum mineralization with complete tantalum liberation at sizes of 300 µm allowed for easy recovery with conventional equipment such as spirals and shaking tables. Over the years, the process and feed material to the plant have drastically changed. Due to drastically reduced liberation sizes, efforts have been made to try to recover as much of the liberated particles as possible in order to maintain acceptable recoveries.

Jan 1, 2005

By William Crowe Kellogg

By now the term AFMAG has been fairly well introduced to the mining industry. Several papers have been presented and published concerning AFMAG (references 1 and 2). However, the term AFMAG remains rather new to the industry, and the exact place which AFMAG occupies in the minerals exploration field is still somewhat uncertain in the minds of many who may have use for this new and interesting method of electromagnetic exploration for conductive minerals. It is the purpose of this paper to again review the basic theory of the AFMAG system, to describe and - illustrate the equipment and data presentation as used in aerial surveying, and to provide some idea of the cost and nature of airborne AFMAG surveys. This paper is primarily of a general descriptive nature and presents AFMAG theory in a schematic rather than mathematical form; emphasis is placed on the equipment, the present method of data presentation and survey operations, since it is believed that such, information will now generally best serve to inform the mining industry of the characteristics of the AFMAG system.

Jan 1, 1960