Search Documents

By M. Newton

Optimization and sensitivity analysis of mineable economic volumes have been standard practise for open pits for many years now, and more recently software has become available to apply techniques for delineating mineable reserves for underground mines. In general these techniques have been applied to a single resource model to quantify mineable tonnes and grade for underground mining. However by using multiple conditionally simulated models both the risk associated with the mining parameters and the risk associated with variations in grade, tonnes and profit can be quantified. Using suitable software the mine planner can then easily and quickly define and compare alternative designs to assess and improve the robustness of and the confidence in the final design.

Jan 1, 2007

By K. Marutiram, T. Umadevi, R. Sah, K. Abhishek

Low-grade iron ore received from the West Singhbhum area of Jharkhand state in India was used to develop a beneficiation flow sheet to remove alumina (Al2O3) and silica (SiO2 ) from the ore to get iron (Fe)-rich product for steel plants. Mineral characterization showed that the main mineral constituents present in the head sample are goethite, limonite, hematite, quartz, clay and gibbsite. The head sample contained about 49.2 percent Fe, 8.79 percent alumina and 12.01 percent silica. The received iron ore sample is amenable to upgradation through beneficiation to get pellet grade concentrate. The beneficiation process was established, involving crushing, screening, jigging, spiral separation, size reduction, desliming and magnetic separation. The process showed significant enrichment in Fe values to 63.5 percent Fe in concentrate, from 49.2 percent Fe. From the developed flow sheet, it is possible to obtain pellet grade fines with 63.5 percent Fe, 2.92 percent SiO2 and 2.61 percent Al2O3 with 50.6 percent weight recovery. The overall tailing loss is 49.4 percent with 34.3 percent Fe, 21.28 percent SiO2 and 14.64 percent Al2O3

A clay binding agent has been investigated to enhance flotation recovery of bitumen from Canadian high fines oil sand in the Clark Hot Water Extraction (CHWE) process. Selective adsorption on fine particles and subsequent agglomeration are critical for the success of clay binder enhanced oil sand flotation. A number of flotation tests have been performed at different reagent dosages under different operating conditions such as pulp pH to evaluate the reagent performance. Dissipative Quartz Crystal Microbalance (QCM-D) analyses of clay binder adsorption on quartz were carried out to better understand process mechanisms. It has been found that use of clay binder in flotation resulted in an absolute bitumen recovery increase of 18%, 25%, and 11% for the high-, medium-, and low-grade oil sand samples, respectively. The QCM-D analyses have revealed that the clay binder was strongly adsorbed on the SiO2 surface.

Jan 1, 2012

Steady increases in longwall production have required operators to apply greater quantities of ventilating air in an effort to control and dilute respirable dust. Significant increases in shearer speeds necessitate that longwall supports also be advanced at a faster rate. Both of these factors may contribute to overall respirable dust levels on the longwall face because as supports are lowered and advanced, broken material falling from the top of the canopy is entrained directly into the air stream. To address this issue, the Pittsburgh Research Laboratory collected respirable dust samples from four longwall faces to characterize shield-generated dust. This paper investigates the influence of air velocity and shield advance rates on respirable dust levels. Also discussed are engineering controls currently used to reduce shield dust and alternative controls being investigated by the National Institute for Occupational Safety and Health (NIOSH).

Jan 4, 2010

By D. W. Olson

The estimated value of natural gemstones produced from U.S. deposits during 2004 was $12.9 million. This was a 3-percent increase from that of 2003. U.S. gemstone production included agates, amber, beryl, coral, garnet, jade, jasper, opal, pearl, quartz, sapphire, shell, topaz, tourmaline, turquoise and other gem materials. More than 60 varieties of gemstones have been produced commercially from U.S. mines. But commercial mining of gemstones has never been extensively undertaken in the United States. Most of the deposits have been relatively small compared with other mining operations. In the United States, much of the current gemstone mining is conducted by collectors, gem clubs and hobbyists rather than business organizations.

Jan 1, 2005

By J. P. H. Steele, M. U. Ozbay

As mining operations progress toward tele-mining and autonomous procedures, the need for machine performance monitoring increases. Presently, through a combination of vision, sound, and other subjective observations, an operator attempts to optimize the mechanical excavator’s operation. As the operator is moved away from the face in the case of tele-mining or completely removed for autonomous operation, the qualitative sensory input is lost. This lost information must be replaced with quantifiable sensory input. Chip formation detection may be a suitable replacement sensory input. Chip formation can be predicted with high confidence (>80%) through the analysis of the load waveform associated with the bit/rock interface.

Jan 1, 2002

By W. D. Mayercheck, A. G. Mayton, J. R. Bartels

Abstract-Since 1982, the US Bureau of Mines has inves¬tigated improvements in protection for operators of thin seam shuttle cars. Due to working height restrictions in thin seam mines (<_1.22 m or 48 in.). Federal mine regulations require that canopy protection on shuttle cars he provided only in mines >_1.07 m (42 in.). However, court obtained variances are granted to mines <_1.22 m (48 in). This paper presents ongoing research to design and evaluate a uniquely positioned, ergonomic compartment for a shuttle car that provides the operator with full canopy protection in working heights of 1.02 m (40 in.).

Jan 1, 1989

By G. Kordosky, A. Feather, M. Virnig, P. Crane

Introduction The post World War II nuclear arms race and interest in nuclear power generation resulted in a significant demand for uranium in the 1950’s. This led to the development of uranium solvent extraction technology and uranium became the first metal to be recovered on a large scale by solvent extraction (SX) (1), interestingly more than 100 years after the extraction of uranium from an acid nitrate solution using diethyl ether was first reported by Peligot.(2) For a variety of reasons discussed elsewhere (3,4) there have been upheavals in the supply demand picture and price for uranium since the 1960’s. (Figure 1) The low price of uranium from the mid 1980’s until 2004 resulted in a depression of new resource exploration and mine development along with uranium mine / mill closures and decommissioning. People with skills in uranium processing could not find suitable employment and many experienced engineers and metallurgists took jobs elsewhere or retired. This resulted in a significant brain drain with respect to uranium processing technology.

Jan 1, 2007

By Stephen Davies

Mining at Hudson Bay Mining & Smelting&apos;s Snow Lake Division is now in the mature stage of the mines&apos; lives. These base metal copper-zinc mines have been operating for more than 30 years. Stopes had small pillars called "crown pillars" left between them. These pillars range up to 100 m (330 ft) long by 40 m (130 ft) wide and 15 m (50 ft) thick. Hudson Bay have been successful in removing these pillars by using cable slings, electric scoops, longhole mining and diesel load-haul-dump equipment. The different shapes and sizes of these pillars has required that many innovative techniques be tried in order to find acceptable economic mining methods. An overview of the different methods will be outlined. Background Hudson Bay Mining & Smelting&apos;s Snow Lake Division is located in Manitoba some 800 km (500 miles) north of Winnipeg and 200 km (125 miles) by road from the Hudson Bay smelter complex located in Flin Flon, Manitoba (Fig. I). There are currently three producing underground mines and one open pit operating at the Snow Lake Division, producing copper and zinc concentrates. Pillar recovery is intensive and vital to continued production of these mature mines. The crown pillars are producing more than 50% of the current mine production. This figure will increase in the future. The two mines at which crown pillar recovery is taking place and that will be discussed are the 400 t/d (440 stpd) Rod Mine and the 1000 t/d (1100 stpd) Stall Lake Mine, both five-day-a-week producers. Crown pillar mining has been applied for some time at these mines. However, it was only recently that the crown pillars became vital to production. This has necessitated a number of innovative techniques to recover them.

Jan 1, 1992

By Douglas E. Pollock

Recent NIOSH published information has shown an increase of rapidly progressive coal workers? pneumoconiosis (CWP) in the southern Appalachian coal region (SAR) of the U.S., despite the fact that compliance data indicates that most coal miners have been exposed to coal mine dust concentrations below the statutory limit of 2 mg/m³. While the exact cause of these elevated CWP levels in the SAR has not been established, several factors may be contributing to the increase in occupational lung disease among coal miners. The mining of high rank coal is known to lead to higher CWP rates, and this type of coal is mined in a portion of this region. Also, a high percentage of the mines in the region are on reduced dust standards because of the high silica content of the airborne dust resulting in miners possibly being exposed to excessive amounts of respirable silica dust. Exposure to excessive amounts of respirable silica dust can lead to silicosis, a disabling and potentially fatal lung disease. NIOSH?s Respiratory Hazards Control Branch has been investigating the possible causes that would account for the observed higher trends in disease progression through literature review, data analysis and in-mine surveying. The investigation to date has revealed that underground mines are faced with cutting large amounts of rock in order to maintain haulage clearances. Cutting rock not only increases the potential for silica exposure, it increases the requirement for machine maintenance, which was a concern observed during dust surveys conducted by NIOSH. Over half of the mines operating in the SAR are on reduced standards due to high silica content. Adequate face ventilation of the continuous miner and roof bolter and limited down-wind operations from the miner are also issues of concern and items that require the constant attention of miners operating in these conditions.

Jan 2, 2010

By M. Prud’Homme

Potash is an important natural mineral used largely as a fertilizer in the production of food and fiber. About 93 percent of all potash consumed globally is used in agriculture as fertilizer. The balance is used to manufacture potassium chemicals. Most potash is extracted by conventional underground mining methods. Solution mining is used when underground deposits are irregular and very deep. The other main production method involves the evaporation of brines in shallow salt lakes, followed by the harvesting of potassium minerals.

Jan 1, 2005

By Michael F. Roach, Joseph K. Cavey, Gary E. Taylor

A rigorous horizontal drilling and chemical grouting program was specified beneath the Hollywood Freeway (U.S. Route 101) section of Los Angeles Metrorail Contract C-311.Twin 6.67-m (22-ft.) diameter starter tunnels were to be conventionally mined through amixed alluvial and bedrock face consisting of silty sand, gravel, and weathered sandstone and siltstone of the Topanga Group. The contact between the alluvium and bedrock dipped toward the Crossover Excavation where the horizontal drilling and grouting operations were performed. The intent of this grouting program was to stabilize the mixed face to minimize ground loss and surface settlement, and to reduce groundwater inflow into the tunnel headings. Given the highly variable mixed face conditions, horizontal drilling up to 86 m (284 ft.) resulted in upward trending trajectories which likely followed the bedrock contact. Chemical grouting was performed in a primary, secondary and tertiary, three dimensional sequence. Evaluation of the primary and secondary grouting parameters indicated where tertiary grouting was required. Grouting pressures induced a small rock failure at the tunnel heading as well as increased stresses on the tiebacks of the excavation.

Jan 1, 1997

By R. Bokotko, J. D. Miller, J. Hupka

Laboratory results from an initial study on the removal of SO2 from gas mixtures are reported using air-sparged hydrocyclone (ASH) technology. Tap water and alkaline solutions were used for absorption and the influence of gas flow rate, water flow rate and length of the ASH unit were investigated. Complete removal of SO2 was possible with very favorable kinetics. The efficiency of sulfur dioxide absorption from air using the ASH is compared with the efficiency of conventional technology.

Jan 1, 2002

By R. D. Sharpe

Gypsum wallboard manufacturers in the United States shipped 3.18 billion m2 (34.2 billion sq ft) of wall-board products during 2004 versus 2.93 billion m2 (31.5billion sq ft) in 2003. Following a historic high production of gypsum wallboard products in 1999, production decreased in 2000. But it has steadily increased during2001 through 2004. Wallboard production in the United States increased about 8.6 percent in 2004 from 2003. Following several years of a “building boom” of new wallboard plants and the expansion of the manufacturing capacity of several existing plants, 2004 was a relatively quiet year. However, several new plants and capacity expansions were announced or are in progress during 2004.

Jan 1, 2005

By William W. Edgerton, Calvin Locke

INTRODUCTION King County, Washington operates a regions wastewater treatment system that provides treatment to 18 cities and 16 sewer districts in the greater Seattle metropolitan area. The system serves 1.4 million people and currently includes two regional treatment plants. In 1999, a long-range planning study identified the need for a third regional treatment plant, now known as Brightwater. Prior to this project, the county has almost exclusively used the traditional design-bid-build delivery process for its capital projects. However, with the adoption of the RWSP, the county began to study the potential application of innovative project delivery methods. This paper looks at the project delivery methods used for the Brightwater project, based on the specific needs of this large, complex, and multi-faceted project. THE KING COUNTY WASTEWATER TREATMENT SYSTEM In 1958, voters approved the formation of a regional agency called the Municipality of Metropolitan Seattle, or Metro, to build and operate a regional wastewater collection and treatment system. Prior to the formation of Metro, there were no regional wastewater treatment facilities and pollution of Lake Washington and Puget Sound from untreated sewage was a concern for many residents. In 1994, King County merged with Metro. The county’s 1,087 square kilometer (420 square miles) wastewater service area covers most of urban King County and extends into portions of two neighboring counties. The system includes two regional treatment plants, a local plant, 61 pump and regulator stations, and 571 kilometers (355 miles) of conveyance pipeline which convey wastewater from local districts to the treatment plants. As with other areas, the greater Seattle/King County region has seen rapid population growth. The RWSP estimates that the current system would soon reach capacity, and called for the construction of a new third regional treatment plant, called Brightwater, to be operational by 2010.

Jan 1, 2005

By T. Klemetti

Moisture deterioration of clay-rich roof rocks causes high numbers of roof falls in coal mines in humid summer months. Rocks with high moisture content are generally weaker and can further deteriorate when subjected to wetting and drying cycles. As a result, it is important to evaluate the moisture-sensitivity of roof rock prior to mining. The National Institute for Occupational Safety and Health (NIOSH) has evaluated three moisture-sensitivity index tests on roof rocks from 23 U.S. coal mines. The three tests were the University of Kentucky Weatherability test (Weatherability test), the Consol Energy Water Sensitivity test (Water Sensitivity test), and the NIOSH Immersion test (Immersion test). Of these three tests, the Weatherability and Water Sensitivity tests are more reliable in classifying the moisture-sensitivity of roof rocks. Disclaimer: The findings and conclusions in this report have not been formally disseminated by the National Institute for Occupational Safety and Health and should not be construed to represent any agency determination or policy.

Jan 1, 2009

By R. Dillinger

In the environmentally conscious social atmosphere today, reclamation in surface mines has become a main issue to the public and the regulatory committees. In response to this increased attention, many regulatory committees have begun to enact more stringent regulations on surface mining operations. Operations across all spectrums of the industry have seen changes. Recently and most visibly the mountain top removal mines have seen several new regulations focusing on environmental protection. Specifically regulatory committees have emphasized a focus on the methods of reclamation and recovery of layers suitable for vegetation. These layers are the most visible once the operation has concluded. Also, these layers have the most human interaction (farming, hunting, and house development). Often times the new regulations enacted are shifting from a performance base to a standards base. The key differentiator being a performance base dictates the final result while a standards base dictates the method to achieve the result. The very nature of many regulations (especially those that are standards based) not only challenges the physical limitations of the equipment used today, they come with a financial impact. For the purpose of this paper, the model will be a surface coal operation, utilizing draglines as primary overburden movers. The coal seam is ten feet thick, the overburden ninety five feet thick, the pits are 150 feet wide, and the dragline is a Bucyrus Erie 1570.

Jan 1, 2011

By R. D. Hagni, P. A. Shivdasan

Cathodoluminescence microscopy (CLM) is uniquely applicable to the study of carbonatite-related fluorspar ore deposits. The mineralogy of the carbonatites, sodic and potassic fenites, marbles, quartzites, and fluorite ores are readily determined and characterized. Calcite, dolomite, apatite, fluorite were deposited dominantly under high temperature conditions and they exhibit strong cathodoluminescence (CL). Three types of carbonatites have been recognized at the Okorusu, Namibia carbonatite complex and fluorspar mines by field mapping and laboratory CLM. The main carbonatite intrusion is fine grained and consists mainly of calcite. A later phase of pegmatitic carbonatite consists of calcite, magnetite, Fe-rich pyroxene, apatite, and pyrochlore. Pyroxene carbonatites were recognized mainly through their study by CLM.

Jan 1, 2001

By S. Chander, S. W. Musselman

The molecular structure of hydrophobic and hydrophilic groups in nonionic surfactants has been related to the wetting and dispersion of selected pigments. The nonionic surfactants included in this study are acetylenic diol based surfactants and ethoxylated alkyl phenols. The Langmuir model could be used to fit adsorption data. Further analysis of the data showed that the free energy of adsorption was a function of adsorption density of the surfactants at the interface. The change in free energy with adsorption density could be interpreted by considering a change in the orientation of the adsorbed molecules. Acetylenic diol based surfatants were found to have an area per molecule of 2-3 times that of similarly ethoxylated alkyl phenols. The wetting and dispersion properties of lamp black, a model hydrophobic surface, by these surfactants were investigated by contact angle measurements and particle size analysis. Acetylenic diol based surfactants with ethylene oxide contents between3.5 and 10 moles per molecule and alkyl phenol based surfactants with approximately 9 moles of ethylene oxide per molecule were found to provide superior wetting abilities. Longer ethylene oxide chains were required for superior dispersion capabilities within each family of surfactants. Complete wetting and dispersion was found to occur above the critical micelle concentration of the surfactants.

Jan 1, 2000

By Constance F. Acton

Based on laboratory structure analyses, a pilot plant investigation was undertaken to evaluate a Michigan conglomerate native copper ore. Comminution or sized feed was accomplished using wet, closed circuit autogenous grinding with and without crushing of the recirculating load. Coarse metallics were concentrated in two stages of jigging with fine metallic copper being recovered in a three-stage xanthate flotation circuit. With a feed averaging 2.09 % Cu, copper recovery ranged from 86-93 % Cu with an average grade of 55.5 % Ca. An evaluation of the processing flowsheet is made in terms of pertinent independent, dependent, and external variables and design factors. Rate equations are developed to describe the grinding and flotation circuits separately as well as the entire circuit as a whole. Performance equations for the overall operation and for the unit operation of autogenous grinding alone are developed in terms of suitable capacity, efficiency and energy consumption terms. Thus, the effects of feed rate, recirculating load and flowsheet design can be rationally evaluated. Energy consumption for various conditions in the pilot plant is compared to the laboratory value. Additionally, size and scale up factors are discussed. Recommendations are made for further studies to be undertaken to further quantify the ore characteristics and the nature of the autogenous grinding operation. However, the feasibilty of beneficiation of this type of native copper ore by means of an autogenous grinding/jigging/flotation circuit is clearly established.

Jan 1, 1977