Search Documents

By W. C. Goldberg, E. M. Frizzell

Monitoring slope displacement in open-pit mines can help predict collapses and prevent serious damage, injuries, and fatalities. Early detection of movement may indicate the need to modify slope geometry, initiate dewatering if the slope is wet, or consider artificial support measures such as cable bolting. Slope monitoring at the Berkeley pit was carried out with varying degrees of intensity and continuity for about 15 years. Some of the old mine records are still intact and accessible. Slope monitoring data can therefore be collected and published for the benefit of other mine operators. Because prediction of slope failures is empirical in nature, publication of several well documented case studies will be a valuable contribution to the industry. Background - Berkeley pit Open-pit mining of copper from the Berkeley pit, located on the east side of Butte, MT, began in 1955 and ceased in 1982. During that time, about 1 Gt (1.2 billion st) of material were removed to form a pit about 1.8 km wide by 2.1 km long (6000 ft by 7000 ft) at the rim, and 550 m (1800 ft) deep as measured from the high hill on the northwest side. From the south side, the pit only measures 365 m (1200 ft) deep. The Berkeley pit was first owned and operated by Anaconda Minerals Co., and subsequently by Arco. Following its closure in April 1982, the mine began to fill with water. Washington Construction purchased the property in 1986, and Montana Resources Inc. began mining to the east of the Berkeley pit in July 1986. Numerous instances of slope failure were recorded during the course of mining and several intensive geotechnical investigations were conducted in an effort to optimize the mine design. One of the last and most comprehensive studies was initiated in 1977. For purposes of geotechnical analysis, the mine was divided into nine design sectors on the basis of geologic conditions, geographic orientation, and economic importance (Fig. 1). Only two of these sectors - the concentrator and the southeast corner - are considered here. Material properties were obtained from several studies of samples collected from the mine and adjacent areas. The slope was monitored using standard surveying techniques to record the amount of movement in an area. The

Jan 1, 1989

By E. R. Spencer

National Institute for Occupational Safety and Health (NIOSH) researchers conducted an investigation to quantify sound levels and to determine the amount of sound reduction provided by engineering noise controls installed in a talc processing plant. Baseline sound level and sound intensity measurements were performed at the plant and the measurement locations were recorded for comparison to post-control measurements. Follow-up measurements were then made at the same locations after the initial noise controls were installed. The plant subsequently decided to implement additional noise controls and the researchers returned to conduct measurements for a final analysis of all noise controls. The most significant results showed a sound level reduction in the main mill area from a range of 93-104 dB(A) down to 90-94 dB(A), and a total sound power level reduction of 21 dB(A) for air classifying mill 3.

Jan 1, 2008

In this paper, uniaxial compression tests were conducted on intact rocks and broken rocks that were reinforced by grouting, and the effects of grouting on the strength of broken rocks were analyzed. The results show that after grouting reinforcement, the bearing capacity of broken rocks with different lithologies increased, and their uniaxial compressive strength recovered by approximately 6%–16%. The results indicated that the stronger the rock, the smaller the strength recovery of the consolidated body formed after grouting. At the same time, using borehole camera observation and deep overburden strata separations, the fracture development characteristics of surrounding rocks of the gob-side retained entry were analyzed and divided into different regions. On this basis, a guided grouting method was proposed; that is, shallow hole grouting was first used in the plastic zone of the broken surrounding rocks to form the isolation layer, and then deep grouting holes were arranged in the elastic-plastic zone of the transition zone to guide the slurry flow to the shallow unfilled zone. Therefore, the broken surrounding rocks were reinforced into an integrated body and selfbearing capacity improved.

Jul 28, 2020

By S. Hamilton

Borates are essential to life, and to many products that are essential to an acceptable standard of living. They occur naturally in seawater at an average concentration of five milligrams of boron per liter. Fresh water lakes, rivers, streams and ground water generally have concentrations of about one milligram boron per liter. Borates are also present in soil at concentrations ranging from 0.1 to three milligrams of boron per kilogram. Because most of that boron is locked into insoluble minerals, clay or organic matter, boron deficiency is more widespread than boron enrichment. Borates evaporate into the atmosphere from seawater, rain, snow and hot springs. In rain and snow, natural boron concentrations range from 0.002 and 0.1 milligrams boron per liter. All told, boron moves through the atmosphere at a rate of 5 Mt to 7 Mt/a (5.5 million to 7.7 million stpy).

Jan 1, 2005

By R. J. Snoby, M. A. Short, A. Jungmann

In processing coal, the low concentrate value requires high capacity production and sharp classification/separation techniques to reduce specific production costs. The allflux separator meets these criteria with a unique two-stage design. Through a combination of rising current and fluidized bed technologies, the allflux has extended the state of the art by expanding the particle size range that can be efficiently processed. Using concepts that have proven successful in processing concrete sands, small-scale industrial testing with coal feed stocks looks very promising. Attractive applications for the allflux are projected in fine coal recovery from old settling ponds or as a retrofit in existing fines circuits.

Jan 1, 2001

By B. P. Spigarelli

To meet the growing need for CO2 capture and storage technology, Michigan Technological University is researching CO2 capture and storage using carbonate solutions. The objective of the present study was to increase the absorption rate of CO2 into the carbonate solution without reducing the absorption capacity of the solution. This approach used a polypropylene glycol methyl ether (PPGME) as a surfactant to chemically alter the gas bubble size. Experiments were conducted to study the absorption rate of CO2 at varying surfactant concentrations of 0, 0.12, 0.24, 0.36, and 0.48 g/L. Results showed that as the concentration of surfactant increased in solution, the absorption rate also increased. The CO2 absorption rate increased from 3.45 mmol/min CO2 at 0g/L PPGME to 3.92 mmol/min CO2 at 0.48 g/L PPGME. This amounted to a 14% increase in the CO2 absorption rate with no decrease in absorption capacity of the solution.

Feb 27, 2013

By Z. Yu

Low-rank/oxidized coals respond poorly to oil agglomeration. Emulsification of kerosene in the presence of surfactants dramatically reduces the size of the kerosene droplets. While this dramatically reduces the amount of oil that is required for efficient agglomeration (down to 0.25-0.5%), more importantly, the surfactants entirely change the electrokinetic properties of the oil droplets and thus the interaction between oil droplets and coal particles. Consequently, kerosene cationic emulsions can efficiently agglomerate oxidized coal particles. The agglomerates obtained in such a process can still be recovered by screening. Surfactants can affect fine coal filtration very profoundly when used to emulsify the oil which is utilized to agglomerate coal prior to its filtration. This sequence is much more logical than the use of flocculants - highly hydrophilic polymers - as filtration additives to aid dewatering of flotation concentrates. Although such polymers flocculate coal particles, they also render coal surfaces hydrophilic and make reduction of the cake moisture content difficult.

Jan 1, 2000

By Janet A. Flinn, David G. Fileccia

Machine guidance and control systems have become more pervasive in the mining industry in recent years but not always from mining-experienced providers. Dozers, motor graders, scrapers, excavators, shovels, draglines, drills and haul trucks are just a few examples of the types of heavy machinery now equipped with global positioning system (GPS)-aided guidance systems. While equipment manufacturers are offering their own software, many only supply solutions for the machines they produce. The proliferation of GPS equipment manufacturers entering the machine guidance and control arena has resulted in a multitude of makes and models of GPS receivers. Some of these companies also produce their own guidance software. But they usually just specialize in a narrow range of heavy machinery. So customers are forced to use multiple systems and face new challenges in implementation, training, reporting and inter-system communication.

Jan 1, 2006

Newcrest Mining is one of the leading independent gold producers in Australia thanks in large part to its Cadia Valley operations. It is the largest gold and copper producer in New South Wales and one of the largest in Australia. This year Newcrest will expand its operations with a A$545-million expansion in the area. The Cadia Valley is approximately 250 km (155 miles) west of Sydney. The province presently includes the Cadia Hill opencut mine and the Ridgeway underground mine. With a significant mineralized system to the east of Cadia Hill and a mineral resource below Ridgeway, Cadia Valley has the potential to underpin Newcrest?s production for up to 30 years. In 2007, total gold production for the company in-creased to more than 50 t (1.6 million oz) and cash flow increased by 47 percent, according to the company?s annual report. The history of mining in the area dates back to 1851, but Newcrest?s history is young. In 1990, Newcrest commenced activities in the Cadia Valley. In 1992, Cadia Hill was discovered, with the discovery of Cadia East (1995) and Ridgeway (1996) following close behind. In 1998, the Cadia Hill openpit mine was commissioned. In 2002, the Ridgeway underground mine was commissioned and in 2007 the company?s board of directors approved an A$545 million development of the Ridgeway Deeps. The Ridgeway underground mine is located adjacent to Cadia Hill. The Ridgeway orebody has no surface expression but lies approximately 500 m (1,640 ft) below the surface and resembles an inverted teardrop. It measures approximately 450 m (1,476 ft) by 250 m (820 ft) and extends in excess of 850 m (2,788 ft) in depth. Ridgeway is a sublevel caving operation. Crushed ore from underground is delivered by conveyor to a surface stockpile, adjacent to the Ridgeway concentrator. Using similar processes to the adjacent Cadia Hill concentrator, gold and copper are recovered in a conventional flotation circuit to produce a copper concentrate containing elevated gold levels. Ridgeway concentrate is combined with the Cadia Hill concentrate before it is pumped to the filtration plant in

Jan 1, 2008

By F. Bruey

The Factorial Model Experimenters are often interested in systems that are multi-factorial. A multi-factorial system is one whose output is believed or known to be dependent on the particular settings of several inputs, or factors. We can think of these factors as defining a space, with each point in this space corresponding to a particular set of factor settings. Experimenting can be thought of as exploring this space - finding out how the response of the system changes as factor settings are changed. There are several challenges in this exploration, among which are deciding what region to explore, designing an experiment that explores it most effectively, and describing the results of the exploration. This paper deals principally with the last of these; it shows how the factorial model can be used to describe how the response of the system changes as factor settings are changed. A strength of the factorial model is that it treats the factors as causes of change in the system's response and focuses on relations among these causes. In particular, the factorial model focuses on whether causes act independently on the system (in a sense to be explained below), or whether they interact. This is important because the experimenter generally seeks to control the system, and because control based on causes that act independently of other causes is relatively simple, whereas control based on causes that interact is more challenging. Also, mapping the space - finding out how the response of the system changes as factor settings are changed - will require less work if, during the exploration, it can be determined which of the causes act independently. For the sake of example, let us assume that the space we are exploring is three-dimensional, and that we have already defined, for each of the three factors, the range of interest. Let us consider all the ways in which the response of the system might depend on the settings of these three factors. In the simplest case, the response in this region does not depend on any of the factors. The response is constant throughout the space, at say, 80 units.

Jan 1, 2007

By P. Christmann

"In June or July 2005, the European Commission will present its Thematic Strategy on the Sustainable Use of Natural Resources proposal to the Council and European Parliament, one of the seven Thematic Strategies to be developed and implemented under the 6th European Environment Action Programme in support of the European Union’s Sustainable Development Strategy defined by the European Union’s Head of State at the Göteborg European Council, in June 2001. The time scale for this Thematic Strategy is 25 years (2005-2030). This paper discusses some of the key issues related to the EU minerals and metals industry that needs to be addressed by the Strategy. These are: - the need for access to mineral reserves in the EU and abroad; - the need to strenghten the capacity of developing countries to sustainably promote and regulate the use of their mineral potential; - the need for an EU mineral resources intelligence capacity. There are additional important needs, which are not discussed in this paper, such as: - the need to foster further innovation in mining, ore beneficiation and metallurgical technologies; - the need to integrate and simplify the exisitng complex regulatory framework applicable to the EU mining industry and to effectively implement existing legislation."

Jan 1, 2005

By N. A. Karl, D. R. Wilburn

"This summary of international mineral exploration activities for the year 2016 draws upon information from industry sources, published literature, SNL Metals & Mining (SNL), an offering of S&P Global Market Intelligence (New York, NY), and specialists in the U.S. Geological Survey (USGS) National Minerals Information Center. Three types of information are reported and analyzed in this annual review of international exploration: 1) budgetary statistics expressed in U.S. dollars provided by SNL; 2) regional and site-specific exploration activities that took place in 2016 as compiled by the USGS and 3) regional events and legislation that affected exploration activities including economic, social and political conditions, which were derived from published sources and discussions with USGS and industry specialists. Commodity and regional compilations are presented in this summary. Because multiple sources were used to develop commodity and regional compilations, statistics may vary depending on the source and type of data that are being reported. The SNL data summarize budget estimates for worldwide exploration activities in 2016 for 30 nonfuel mineral commodities and metal alloys, based on company surveys. Surveys focused on precious metals (gold, platinumgroup platinumgroup metals (PGMs) and silver), base metals, (cobalt, copper, lead, molybdenum, nickel, tin and zinc), bulk commodities (bauxite, chromite, iron ore, manganese, phosphate and potash) and other commodities (aluminum, antimony, diamond, graphite, heavy-mineral sands, lithium, niobium, rare-earth elements (REEs), scandium, tantalum, tungsten, uranium, vanadium and yttrium). Information on uranium exploration activities was included in SNL’s survey for the first time in 2007. Data on lithium, niobium, phosphate, potash, REE and tungsten were compiled for the first time in 2010, and scandium, vanadium and yttrium were added in 2014 because of their increased topical significance. Since 1999, companies with exploration budgets of $100,000 and greater were included in the SNL surveys. SNL budget estimates exclude coal, and oil and gas. The 2016 SNL mining company survey compilation was reported by SNL to include an estimated 95 percent of the world’s nonfuel mineral exploration budgets. The 5 percent that was not covered was accounted for by companies that chose not to participate in the SNL survey, private companies that do not publish their budget data and government-funded exploration activities."

Jan 5, 2017

As opposed to a prescriptive-based design, a performance-based fire-protection system design allows the system planner the flexibility in choosing specific method, materials and design tools to achieve a preset goal. A different approach in fire protection and a powerful addition to existing method, the system has been around for many years, and has gone through numerous improvements. Despite its popularity in the building industry, it has not been introduced to the mining industry yet. As mines get deeper, increases in size and complication, mine fire safety system will also become increasingly challenging, a new and proven system should be able to great potential to eradicate many of the problems that are either unsolvable or cost-prohibitive with the traditional method. With increasing globalization and international exchange with other major mining countries a common language/practice also make the performance-based design method a desirable feature in mine fire safety system. This paper will first define a performance-based system, step-by-step design methods, likely impacts on fire-protection practices and possible challenges in implementing the system in US underground mines.

Jan 1, 2011

By J. A. Organiscak

Water spray applications are one of the principal means of controlling airborne respirable dust in coal mines. Since many coals are hydrophobic and not easily wetted by water, wetting agents can be added to the spray water in an effort to improve coal wetting and assist with dust capture. In order to study wetting agent effects on coal dust capture, laboratory experiments were conducted with three wetting agents used by the coal industry on -325 mesh sized Pocahontas No. 3 coal dust. Significant differences in coal dust sinktimes were observed among the three wetting agents at water mixture concentrations of 0.05%, 0.1%, and 0.2%. The best wetting agent as identified by the coal dust sink test was only tested at the lowest 0.05% water mixture concentration and was found to have a negligible effect on spray airborne dust capture. Water spray airborne dust capture results for all three wetting agents tested at a 0.2% water mixture concentration showed that all three wetting agents exhibit similar but small improvements in dust capture efficiency as compared with water. These results indicate that the coal dust sink test may not be a good predictor for the capture of airborne dust. Additional research is needed to examine if the coal dust sink test is a better predictor of wetting agent dust suppression effects during cutting, loading, conveying, and dumping of coal products by comparison to airborne dust capture from sprays.

Feb 27, 2013

By S. Addie

In the early 1990’s the British Columbia (Canada) mineral industry frequently discussed the need to participate in, and compromise with, public environmental interests in order to ascertain long-term stability. However, as the decade progressed the mineral industry withdrew from almost all meaningful public participation. As government protected areas policy in the past year has illuminated, there is a continued need for long-term land access stability. This paper historically analyses the public engagement policies of the British Columbian mineral industry while it participated in long-term consensus-based multi-stakeholder land-use planning processes. From this analysis the paper recommends that the mineral industry reengage the public and institute a new working relationship with environmental advocacy groups so as to ensure British Columbia becomes the most sustainable mineral producing jurisdiction in the world.

Jan 1, 2011

By M. Karmis, C. Haycocks

The evolution of longwall mining is briefly traced from its inception in England in the 1620's. In the beginning this method recovered 90% of coal with roof closure controlled by packs and walls. Mechanization began with kerf cutting, crude face conveyors, and improved face support. Full face mining was accompanied by the introduction of self- advancing hydraulic supports. U. S. longwalls evolved a retreating system to recover blocks of coal outlined by room and pillar panels. Computer control combined with the most modern technology have greatly increased productivity. Past trends are used to predict future technological directions.

Feb 24, 1997

By W. Dziurzynski

The present article sets forward the results of field tests that made it possible to validate the mathematical model used in the VENTGRAPH ventilation engineer programmes. The case considered relates to the introduction of a new heading to the ventilation network of the mine. The utilisation of computer programmes in practice is justified by the necessity of ensuring expected performance and secure conditions in the network of mine headings, where - for example - plans are being made to utilise the transport dip-heading, taking into consideration fire and methane hazards. In the article we have presented the methodology of preparation of a database for computer programmes of the VENTGRAPH system, obtained on the basis of ventilation measurements. The next step consists in the execution of a design of the modified network and prediction, this on the basis of heading geometries, of parameters characterising the flow of air for the designed headings. Due to the fact that the heading was in the final stage of driving, following its introduction to normal operation and the stabilisation of flow values it was possible to retake ventilation measurements, which validated the results obtained through computer simulations. In order to execute measurements of the volume flow in the dip-heading, we employed a new wireless multipoint measurement system to determine the velocity field of air in the mine heading; the results are characterised by a high accuracy of measurement. As a part of fire prevention and incident management planning, a series of underground fire case studies for the a validated network flow model has been made. Results of simulations show the capabilities of the FIRE module of the mentioned software, including assessment of stability of flow directions and hints on counter and preventive measures for particular locations of fire.

Jan 1, 2009

By Albert Adu-Acheampong

Fairmount Mineral's Maiden Rock underground sand mine historically delivered air to ventilate diesel-powered equipment at its working faces through high-resistance, 381-mm- (15-in.-) diameter PVC distribution lines. In support of plans for expanded production, three new, low-resistance ventilation design alternatives were analyzed. The study determined that adequate ventilation for expanded production was possible with various commercially available, high-volume/ low-pressure fans combined with a systematic layout of control structures. The recommended redesign was implemented in 2001, resulting in a significant increase in flow volumes and a noticeable improvement in the mine environment.

Jan 1, 2008

Soil erosion is strongly related to soil hydraulic properties. Understanding how surface coal mining impacts those properties is important in developing effective management practices to control erosion during reclamation. Soils from undisturbed areas, roughly graded mine spoil, replaced topsoil before seeding, and revegetated areas at the Rosebud Mine in Eastern Montana were evaluated to determine impacts on soil hydraulic properties. Field and laboratory studies were conducted to determine soil hydraulic properties, including particle-size distribution, organic matter content, and saturated hydraulic conductivity. WEPP simulations and risk analyses were performed on the soil hydraulic property data to determine the impacts of changes on soil erosion. The hydraulic properties of the soils in each representative area have significant differences due to the mining and reclamation practices at the mine. WEPP simulations show that the potential for soil erosion increases due to mining activities disturbing the soil. WEPP simulations also indicate that the potential for erosion may return to pre-mining levels over time with effective revegetation practices.

Feb 27, 2013

By G. Van Weert

Mining project feasibility is projected from a geological model and a mining plan. Ore grade is assumed to be continuous, based on drill hole assays as much as 80 m apart. Eighty meter is 80,000,000 micron. Base metal concentrators may be said to work at 80 micron, for flotation at least. In short, metallurgical and financial performance in green field metal mining is forecast on rejecting waste after comminuting the ore down by roughly a volume factor of 1,000,000,000,000,000,000 (1018) from the feasibility/banking study parameters. This is the gap between mine and mill, between present sulphide mining practices and mineral dressing capabilities, and ultimately between lenders/shareholders expectations and mine/mill performance. By inserting a new upgrading technology in this gap, new opportunities for reserve enhancement and cost reduction are created, and risk could be reduced. Blast holes for extracting the outlined ore might be 8 m apart. Most ore bodies do not abruptly change composition at 8 m intervals; nor are they homogeneous in grade at the 8 cm (3?) rock size, optimum size for sorting. Mining in 8 m blocks will inevitably cause dilution of the mill feed and ore losses in the waste rock. This is well recognized in the mining industry. Much work is going on applying the vast data storage and manipulation capability of computers to mine scheduling. One only has to consult the SME Annual Meeting presentations. At the 2007 Meeting, Clark and Dagdelen described the challenges faced by Newmont at its operations and the application of sophisticated software tools and methods in its search of solutions to mining optimization. Block models can often contain in excess of one million blocks. Additional complexity exists when multiple grades are modeled for each block. The authors identify the main optimization problem as the system?s ability to cater to large scale problems in an acceptable timeframe; in other words, still larger computers are needed. At the same Meeting, Menabde et al (2007) presented a new pit development planning tool called Blasor, developed by BHP Billiton Technology, and its co-developed Blasor IPD (In Pit Dumping), (Zuckerberg et al (2007)). For purposes of this paper, Blasor/IPD incorporates options on processing capacity constraints and blending targets, eliminating arbitrary up-front decisions about cutoff grades for each block of material in the extraction sequence.

Jan 1, 2008