Search Documents

By D. F. Malan, D. Ile

This study explores the use of backfill in hard rock bord-and-pillar mines to increase the pillar strength and extraction ratio at depth. The use of backfill will also minimize the requirement for tailings storage on surface and the risk of environmental damage. A literature survey indicated that backfill is extensively used in coal mines, but rarely in hard rock bord-and-pillar mines. To simulate the effect of backfill confinement on pillar strength, an extension of the limit equilibrium model is proposed. Numerical modelling of an actual platinum mine layout is used to illustrate the beneficial effect of backfill on pillar stability at greater depths. The magnitude of confinement exerted by the backfill on the pillar sidewalls is unknown, however, and this needs to be quantified using experimental backfill mining sections equipped with suitable instrumentation.

May 3, 2023

By N. Coulson, P. F. Stewart

The Mine Health and Safety Act No. 29 of 1996, as amended, embeds an occupational health and safety management system that facilitates communication between representatives of the state, capital, and labour. In underground mines, two communication loops between these role players serve to separate the production chain of command from the political tripartite relations. Worker-elected health and safety representatives are involved in both communication loops, but are severely constrained in escalating their occupational health and safety concerns to the legalpolitical level. This has a direct bearing on the exercise of the Right to Refuse Dangerous Work (RRDW). As previously reported, health and safety representatives were found to primarily consult their production supervisors in preference to their trade-union representatives. This follow-up article presents production supervisor perspectives on the RRDW. The study demonstrates how, for mineworkers, the two distinct communication subsystems constrain, rather than facilitate, implementation of the RRDW.

Apr 14, 2024

By Z. Xingrong, L. Jiongtian, Z. Yangge, C. Yijun, L. Liang, H. Yangjia, H. Long

In this present research, a polymer poly (acrylamide-allyl thiourea) (PAM-ATU) with an average molecular weight 1.66 × 104 g/mol was used as a depressant in the flotation separation of molybdenite from chalcopyrite and galena. The micro-flotation experimental results showed that PAM-ATU exhibited a strong influence on the flotation performances of chalcopyrite and galena, but had little effect on that of molybdenite within a pH range of 9.0~11.0 at a dosage of lower than 6.0 mg/L. The flotation results of bulk flotation tests illustrated that PAM-ATU showed a stronger depression power than sodium thioglycollate (TGA) and sodium sulfide. The comparison results demonstrated that PAM-ATU and TGA had an advantage in reducing galena and chalcopyrite impurities in the molybdenum concentrate, respectively. With the combination of PAM-ATU and TGA, a good flotation separation result was achieved through one roughing operation where the recovery of molybdenum in the froth product was over 75.0%, while the recovery of copper and lead were less than 22.0% and 15.0%, individually. It was also found that a molybdenum concentrate with Mo grade of 46.32%, Cu grade of 0.16%, Pb grade of 0.06%, was obtained by a closed circuit flotation flowsheet of one roughing-three scavenging-five cleaning with a Mo recovery of 77.67%. Keywords: PAM-ATU, molybdenite, depressant, chalcopyrite, galena

Jan 1, 2020

By J. D. Steenkamp, J. Muller

"Excavation of an industrial-scale submerged arc furnace, utilized in the production of silicomanganese, identified two high-wear areas in the refractory lining: the tap-hole, built with cold rammed carbon paste and SiC bricks, and the hearth, built with cold rammed carbon paste. To obtain insight into the potential causes of wear, thermodynamic calculations were conducted on eight sets of data, obtained for seven furnaces on three plants based in South Africa. FACTsage software and associated databases – FACTPS, FToxid, and FSstel – as well as the Mn-Fe-Si-C database of Tang and Olsen (2006), were applied. Theoretical indications are that chemical reaction between carbon refractory and slag, as well as dissolution of carbon and SiC refractory in metal, contributed to tap-hole refractory wear; and dissolution of carbon in metal contributed to hearth refractory wear. IntroductionDuring the excavation of a 48 MVA submerged arc furnace (SAF) used for silicomanganese (SiMn) production, it was found that the taphole and hearth were high refractory wear areas (Steenkamp, 2014). In both these highwear areas, carbon-based cold ramming paste formed the hot face refractory lining (crucible). The wear profile of this SAF is presented in Figure 1.The hot face refractory lining was formed by cold ramming of high-grade carbon ramming material. This material consisted of 50–70% anthracite, 15–25% graphite, 6–12% resin, 2–7% tar, 1–5% clay, and 1–5% alumina. The tap-hole was built using SiC bricks, consisting of 75% SiC, 23.4% Si3N4, 0.3% Fe2O3, 0.3% Al2O3, and 0.2% CaO.In the tap-hole area, the wear of the SiC refractory material was estimated at 0.4 t, and that of the high-grade carbon ramming material, at 1.9 t (Steenkamp, Pistorius, and Tangstad, 2015). The amounts of slag and metal tapped during six years of operation of the tap-hole (September 2007 to April 2013) were estimated at 33 088 t (Steenkamp et al.,2015) and 41 360 t, respectively."

Jan 1, 2016

By A. N. Clay, N. N. Moeketsi, S. Joubert

For many years, mine-impacted water has been regarded as a problem and linked to long-term environmental liabilities. However, this water can be a renewable and a sustainable resource, provided that it is managed in a responsible and sensible manner. South Africa’s National Water Resource Strategy (NWRS, 2013) considers water that can be used to contribute to economic activity to be a water resource. Although all water resources are considered as belonging to the State, government does not appear to have meaningfully explored the use of mineimpacted water to contribute to the country’s economic activity. Africa is blessed with more sunshine than anywhere else, apart from Australia, yet we see no rollout of vast quantities of solar panels to ensure every African family has access to affordable power. This suggests that governments are incapable of managing such a free resource. At the same time, apart from the equatorial areas, water is a seriously constrained resource and yet we expect the same entities to manage a commodity none of us can live without. This paper explores the conversion of mine-impacted water from waste to a resource and how the inclusion of other stakeholders (such as water users, landowners, and ordinary South Africans) could benefit the process.

Jan 2, 2022

By S. F. Böde, K. Böde

This paper focuses on developing a comprehensive and pragmatic information technology (IT) strategy for low-margin construction activities. This forms part of the realignment of the general business strategy, and refocusing the operational model. The main elements of the IT strategy formation are analysis of the current IT environment in terms of software and hardware, carrying out a gap analysis, and developing individual functional digitalisation strategies in construction execution based on Building Information Modelling (BIM), business administration processes, communication, business intelligence (BI) and reporting, and data security. Further, substantial emphasis is given to the sustainable strategy implementation in terms of hardware and software readjustments, their integration, user training, and defining the way forward.

Sep 1, 2021

By J. Maritz, K. de Beer, S. M. Buthelezi

The economic upheaval of COVID-19 forced companies to invest in emerging technologies to aid recovery. One such technology is extended reality, which is becoming a mature and innovative tool. Early adopters are seeing significant benefits in learning, training, immersive data visualization, and remote assistance. In South Africa, the mining industry is increasingly interested in using extended reality to optimize and innovate operations. The Minerals Council of South Africa's July 2021 report highlighted the potential of extended reality's to achieve zero-harm production and modernize the industry. However, the extent of extended reality adoption in mining remains unclear due to limited information on its usage. This study addressed this gap by distributing an online survey to assess awareness, knowledge, and current uses of extended reality in South Africa’s mining sector. The results indicated that virtual and augmented reality had the highest levels of awareness and usage, primarily for learning and training. Mixed reality, however, had the lowest awareness and knowledge levels. In terms of applications, visualization and remote assistance had the least use cases. These findings highlight that the South African mining industry is deficient in its understanding and use of extended reality technologies. Without better awareness and application, the South African industry risks missing out on the full benefits of extended reality. The study underlines the need for the South African mining industry to improve its outlook on extended reality technologies to fully leverage their potential applications and benefits.

Jul 10, 2024

By L. Morgan, M. Le Roux, Q. P. Campbell

Dry coal processing is becoming increasingly favoured as a fine coal beneficiation technique. The decline in suitable good-quality coal, as well as the ongoing decrease in usable process water, makes dry beneficiation of the fine coal fraction even more crucial. Dry fine coal beneficiation is a relatively young process with most of the methods still in the developmental phase. Additionally, many of the dry processing options available are better suited for coarser (+6 mm) and easy-to-beneficiate coal. Air winnowing for fine particles has been established in both agricultural and pharmaceutical industries, which indicates that the method can be used to separate smaller particles on a density basis and therefore, may prove effective in the coal industry as well. A proof of concept study was conducted using both computer-based simulations (which do not form part of this paper) and physical experiments. The initial winnowing unit consisted of a closed box with a horizontal air stream flowing through the top section. Coal particles were injected into the air stream and displaced horizontally across a distance (x), depending on the particle size and density, thus actuating a separation based on these two parameters. For this study particle sizes of 6, 4 and 2 mm were used all with a density ranging from 1200 kg·m-3 to 2000 kg·m-3. The simulation in Star CCM+ confirmed the findings of the mathematic behavioural model and provided a virtual representation of the separation using streamlines and particle tracks. The coal tests prove that size separation can be achieved at an airflow velocity of 21 m·s-1 and the density cut-point can also be predicted by using the prediction matrices constructed as part of this study. The results show efficiency values (EPM) of 0.11 and 0.09 at density cut-points of 1400 kg·m-3 and 1500 kg·m-3 respectively. The data obtained from the study indicates that air winnowing can be used to separate fine coal particles based on both size and density. However, in order to achieve an efficient density separation, a narrow size range is required. With some improvements to the model, simulation, method and design, the separation efficiency can also be improved. The next phase of testing will include the upscaling of the process to a demonstration plant, optimising the separation unit and testing the method on different qualities of coal. Keywords: Dry processing, fine coal, winnowing, simulation, tracers, demonstration plant

Jan 1, 2020

By G. Akdogan, Q. G. Reynolds, S. J. Baumgartner

A computational model of a submerged arc furnace (SAF) used in the production of ferrochrome is presented. The model‘s intended use is to investigate the extent to which intrinsic and extrinsic properties of the raw materials affect burden distribution and electrical resistance within the furnace. The model is built on the discrete element method and calculates the mechanical interactions of particle distributions resulting from the flow motion of typical raw materials used in the smelting of chromium ore. This model excludes the effects of thermodynamics, furnace chemistry, and heat transfer. It illustrates how the consumption of materials (chromite pellets, flux, and reductant) is affected by changes in electrode length, reductant fractions, and reductant sizing and density during the formation of a reductant bed. The resistance calculation algorithm developed by Mintek was applied to construct networks developed from particle contacts, which can quantitatively generate estimates of the electrode-to-electrode and electrode-to-bath electrical conduction conditions.

Apr 16, 2024

By S. Heukelman

Zincor uses O2 enrichment (up to 26% O2 in the fluidizing air) to increase the processing rate of zinc concentrates in the fluidized bed roasters. The aim of this study is to determine whether O2 enrichment can be reduced by introducing micro-pelletized concentrate into the feed blend, while maintaining current roaster feed rates and calcine quality. It was found that, with a load of 20% micro-pellets introduced into the feed blend, that O2 enrichment could be reduced by 60%. It was determined that entrained particles spend on average between 0.46 hour and 2.44 hour in the roaster, compared to particles remaining between 3.93 hour and 4.00 hour in the bed overflow. This compares well with a radioactive tracer test performed by Spira. The required reaction time for micro-pellets was found to be less than the residence time inside a Zincor roaster. The result achieved indicated that the average particle residence time inside the roaster was increased successfully in order to compensate for the longer reaction time required to roast micro-pellets at lower levels of O2 in the fluidizing air.

Jan 1, 2011

By R. Uwaoma, A. Goosen, R. Matjie, K. Mphahlele, J. Bunt

Coal properties that are associated with wear and damage of grinding equipment during pulverization prior to combustion were investigated. A South African Highveld feed coal and its beneficiated fractions were crushed to <1 >0.25 mm particles for the grindability tests. These particles were milled and screened into <75 μm and >75 μm fractions, which were analysed by different techniques to establish a correlation with the conventional Hardgrove Grindability Index (HGI). The <1.5 g.cm-3 float fraction, which contained 93 vol.% (mineral matter free) total -macerals,9% kaolinite, and had the lowest HGI (57) (hardest to grind) was pulverized for 15, 30, 60, and 120 minutes for particle size distribution analysis. This analysis indicated that the content of <75 μm particles increases with increased grinding time. The >1.9 g.cm-3 sink fraction, with the highest HGI (76), 44% kaolinite, and 20 vol.% total macerals, was ground easily to generate the highest proportion of <75 μm particles. Based on higher correlation coefficients (R2 = 0.77–0.91), the ash yield, mineral matter, petrographic composition, and fixed-carbon have significant effects on the HGI. Conversely, the inherent moisture and total sulphur (R2 = 0.48–0.62) have only minor effects on the HGI. Results from this investigation could be implemented in the preparation of a suitable pulverized fuel with little equipment wear, as well as utilizing mineralogical and petrographic compositions. Finally, the effect of microlithotypes and maceral types in South African feed coals on the HGI should be investigated in further pulverization and grindability studies.

Jul 5, 2023

By U. König, N. Norberg

Ore mineralogy defines the properties during processing and metal extraction. Fast and frequent monitoring of the mineral content and related process parameters brings value to the mining operation and material processing. Decreasing ore qualities and increasing prices for raw materials require a better control of processed ore and a more efficient use of energy. Traditionally quality control in mining industries has relied on time consuming wet chemistry or the analysis of the elemental composition. The mineralogy that defines the physical properties is often monitored infrequently, if at all. The use of highspeed detectors has turned X-ray diffraction (XRD) into an important tool for fast and accurate process control. XRD data and their interpretation make the difference in the identification of minerals, in describing their distribution in ore bodies and in their beneficiation during processing. The use of statistical techniques such as Partial Least-Squares Regression (PLSR) or Principal Component Analysis (PCA) on XRD raw data has been successfully trialled to determine raw materials and processed ores, in addition to well established methods for mineral identification and quantification. PLSR can be used to correlate process parameters directly from the XRD pattern without investigating the mineral content. Hidden information present in the XRD pattern but not determined with traditional methods can be used to improve the characterisation of the analysed materials. The practical use for the direct determination of process relevant parameters during exploration and ore beneficiation will be illustrated in several case studies from mining and ore processing. Keywords: Geometallurgy, mineral monitoring, X-ray diffraction, process efficiency

Jan 1, 2020

By S. Schutte, J. Pelders, F. Magweregwede, S. Ngobese, W. Botha

A people-centric, systematic approach that involves different stakeholders is considered necessary to successfully address changes associated with modernizing the South African mining industry. In this paper we discuss the inclusion of various South African mining industry stakeholders, particularly the employees, in equipment design and development processes. Data was acquired through a literature review and inputs from South African mining industry stakeholders through focus group discussions, interviews, and an online survey. It was suggested that some of the areas that could be improved by the inclusion of employees in the process are design quality, ergonomics, equipment acceptance by the workforce, safety, efficiency, skills, insight into context of use, and early design iterations and identification of problems. Among the issues considered to be barriers to inclusion were lack of buy-in, lack of resources, difficulty in manufacturers accessing the mines, difficulties in involving too many people, intellectual property concerns, and unavailability of mine employees due to their key responsibilities. Identified critical factors in the equipment design and development process include iterative design, stakeholder participation throughout the process, needs analysis through consultation, and change management. A guideline was developed for worker inclusion in equipment design and development that could be used by the South African mining industry. The study identified several economic and social benefits of including stakeholders in the early stages of design and development. It is recommended that the South African mining industry considers using the developed guideline.

Apr 5, 2023

By B. J. Coetzee, P. W. Sonnendecker

The quality control of a two-stage coal washing process involves several complex components that need to be modelled accurately, to enable autonomous control of the process. The first objective is to develop a method to track the material through the washing process, while ensuring accurate washing prediction models are used. This was achieved through a digital twin model of the Grootegeluk 1 coal processing plant. The model is the amalgamation of manipulating and combining of data-sets from the plant historian, geological wash tables, and mining dispatch servers. This information is then used to control and set the processing medium densities of all 15 modules on the plant, 10 modules in the primary wash and 5 modules in the secondary wash. This controller has been successfully implemented and controlled the plant for 10 days.

Aug 2, 2022

By N. Sacks, N. B. S. Magagula, I. Botef

"Low-pressure cold gas dynamic spraying was used to deposit WC-4wt%Ni and WC-4wt%Ni-1wt%Mo coatings onto mild steel. Dense coatings with very low porosities were produced. No decarburization occurred during deposition and no deleterious phases were formed. The coatings were subjected to standardized material characterization tests, as well as slurry abrasion testing to assess their wear behaviour. The wear tests were conducted in synthetic minewater-silica slurries, while distilled watersilica slurries were used as a control. The hardness of the coatings, 512HV0.3 and 458HV0.3 for WC-4wt%Ni and WC-4wt%Ni-1wt%Mo respectively, are comparable to those achieved using high-temperature coating processes. The abrasion wear rates for both coatings were less than 5 mg/min and 10 mg/min in the distilled water-silica and synthetic mine water-silica slurries respectively. The approximately 50% increase in wear rate in the synthetic minewater slurry is attributed to a synergistic corrosive wear mechanism. The predominant wear mechanisms were identified as binder smearing and delamination, with carbide grain fracture and pull-out. IntroductionSlurry abrasion is a common phenomenon in mining operations, particularly in pipelines transporting, for example, sand-water slurries. This type of wear can cause pipeline fracture, shortened operational lifetimes, and impede pipeline efficiency. To reduce or limit abrasion, thermally sprayed tungsten-carbide-based coatings are often used as pipe linings (Kanchan et al., 2010). This is due to their attractive mechanical properties, which include high wear resistance, stiffness, hardness, compressive strength, and tensile strength. These properties are provided by the coating microstructure and composition, which is a blend of hard, wear-resistant tungsten carbide (WC) particles embedded in a fracture-tough metallic binder phase (Brookes, 1997). Cobalt (Co) is the most commonly used binder due to its excellent wetting of the WC phase and moderate mechanical properties; however, its application is limited to non-corrosive environments as it has a low corrosion and oxidation resistance (Andren, 2001). Nickel (Ni) may also be used as a binder, and has been shown to have superior oxidation and corrosion resistance, but in some applications may not have the required mechanical properties (Kim et al., 2006)."

Jan 1, 2016

By D. Kok

A challenge in mine planning is the optimal allocation of resources to the appropriate workplaces within the shift cycle (labour, equipment type, and other resources) in order to carry out the shift cycle activities, achieve planned production targets, and ultimately maximize production within all infrastructure constraints. Generally, detailed mine planning is done on a monthly basis at a workplace level in order to determine the production targets. The production supervisor, mine overseer, or equivalent production manager must then make the appropriate resource allocation trade-off decisions on a daily basis per shift to try and deliver to the plan and required production target. Due to the complexity and number of permutations of possible resource allocation decisions, it is impossible for a human brain to make the appropriate and optimal allocation decisions that will result in achieving the maximum or target production. These allocation decision permutations must deal with the current status of workplaces (availability, position in the cycle etc.), the status of equipment availability (available, planned maintenance, or breakdown etc.), distance between the workplaces (traveling time of equipment between workplaces, etc.) and equipment type required for that shift cycle activity. All these factors need to be taken into account in resource allocation to plan for the shift, and even during the shift if a major piece of equipment becomes unavailable or a workplace activity is not progressing as planned. This paper is a case study on how an optimization algorithm can be used to create a production planning system for optimization of resource allocation in a mechanized underground platinum operation. A business case for optimal allocation of resources is demonstrated and compared to the current manual planned allocation.

Jan 1, 2012

By R. Altındag, D. Akbay

The point load index is a simple, fast, and inexpensive method for determining rock strength and can be applied both in the field and in the laboratory. There are, however, some disadvantages and limitations to the method, and the test results can be affected by the person carrying out the test, the rock characteristics, or the test device. In this study we describe an investigation into how the point load index value is affected by the shape of the conical platens used in the test. Point load index tests were carried out using different devices fitted with conical platens of different spherical radii, and on a modified device which circumvented the limitations/disadvantages. It was seen that the point load index value increased as the platen radius increased, as expected. In the case of testing using non-standard conical platens, an equation is proposed to normalize the point load index value with respect to the standard spherical radius value.

Nov 1, 2021

By F. Magweregwede, S. Khan

Circular economy opportunities for the mining sector are presented in this paper. A literature review was undertaken, followed by qualitative data gathering through survey questionnaires and unstructured interviews, and stakeholder engagements through workshops. The circular economy opportunities were identified and categorised according to the three circular economy principles of designing out waste and pollution, keeping products and materials in use, and regenerating natural systems. Opportunities aligned with the first principle include increased ore extraction efficiency processes, water recovery and recycling, substitution of raw materials, technology and waste utilisation for carbon capture and biotechnology. The second principle includes opportunities such as zero waste-to-landfill strategies, repurposing of mine waste, re-mining of tailings, recycling metals and processing of residues, and urban mining of electronic waste. Opportunities aligned with the third principle include the adoption of renewable energy, green hydrogen production, repurposing of post mining landscapes, and eradication of alien invasive vegetation. Furthermore, the challenges of implementing circular economy in the mining sector are discussed. The current rate of waste generation from mining activities far exceeds the rate of reuse and repurposing. Recycling of large tyres and characterisation of hazardous electronic waste also pose challenges. The most implementable circular economy opportunities in the mining sector are those aligned with the second principle of keeping materials in use. The high impact opportunities aligned with the first principle of designing out waste and pollution, and the third principle of regenerating natural systems, are more difficult to implement as they require large investments.

Dec 15, 2025

By F. Dutoy, M. B. Stella, C. F. Carrozza

Rare earth elements (REEs) are indispensable components in the manufacturing of high-tech devices, renewable energy technologies, and defence applications. As global demand for these elements continues to rise, there is a pressing need to optimize extraction processes for both efficiency and environmental sustainability. This study explores approaches to rare earth extraction using Ionquest® 801 and integrates a predictive modelling to enhance process understanding and optimization. We conducted a screening test varying pH process to evaluate the best extraction efficiency. Starting pregnant leach solution (PLS), solution was prepared in the lab with the following rare earth elements: La, Ce, Gd, Dy, and Υ, at 0.02 M for each element. The data obtained were used to develop empirical and mechanistic models to predict rare earth extraction yields and flowsheet. Further tests were performed by mixing specific concentrations of different extractant and/or phase modifier. Our experimental results demonstrated the effectiveness of the proposedextraction methods, highlighting improvements in both yield and selectivity. The developedmodels successfully captured the complex relationships between process parameters and extraction efficiency, providing valuable insights for process optimization.

Nov 6, 2024

By F. T. Cawood, C. C. Birc

The South African mineral resource royalty system, initiated in 2010, employs a hybrid ad valorem approach tied to profitability ratios. This rate is then applied to the total revenue from mineral sales. In this article we explore how the profitability ratio in the mineral resource royalty formulae interacts with the gold tax formula as applied to South African gold mines, devising a strategy for cut-off grade optimization. The study focuses on nine narrow, tabular-reef (Witwatersrand) gold mines. The approach involves a mixed-integer cut-off grade optimizer utilizing Excel Solver, incorporating relevant royalty and income tax formulae. Different mineral resource royalty cost scenarios were examined. Ignoring these costs in the break-even analysis lowers the cut-off grade but slightly boosts profits compared to considering expected costs. The developed optimizer model, recognizing the profitability aspect of the mineral resource royalty and income tax formulae, yielded a 6% lower cut-off grade than the base case. This is significant for increasing mine life. While the profit differences are marginal (0.2% compared to the break-even base case), substantial improvements were noted: a 6% increase in stope tons above cut-off grade, and a 4% rise in total revenue. Enhanced resource utilization (3% extra gold kilograms) reduces necessary development and overall costs, allowing for a reduction in the cut-off grade and ultimately, more profit.

Aug 8, 2024