Search Documents

By Piyush K. Dutta

This report describes the design, development and manufacture of production stoper drills and results of their field tests, it is shown that underground stoper drill noise level can be reduced from 118 dBA to below 100 dBA by using these pneumatic drills. The design concept of these drills is a radical departure from the standard valved rifle bar type drill machine design to a drill featuring a valveless independent rotation system, use of an integral muffler and a shroud tube. Six drills were manufactured in a standard commercial drill manufacturing setup and organization. The design and production technology proved that commercially viable quiet drills can be made available for mine use.

Jan 1, 1983

By W. E. Bruce, James Paone

Drillability or a measure of drilling performance has been based on ( 1 ) hardness and toughness of rocks , ( 2 ) power input to the drill compared with total volume of hole , and ( 3 ) penetration related to resistive forces of rock on the applied penetrative forces . An analysis of some representative previous work is made . Experimental drillability curves from AX- size diamond core bit performance in eight different rocks ranging from dense hard taconite to soft limestones are presented . Results show that in small bore diamond drilling , compressive strength and possibly other rock properties may be a useful parameter in predicting drilling rates .

Jan 1, 1963

By Richard C. Wang

The U.S. Bureau of Mines established a wire rope research laboratory to examine the factors that affect the safety and the useful life of wire rope. In the most recent work, two 32-mm 6x27H flattened strand ropes were degraded on a bending fatigue machine. The two tests were run at constant loads of 285 and 347 kN or safety factors of 2.5 and 2. Nondestructive and tensile strength tests were performed on samples of the ropes to determine the relationship between rope deterioration and rope breaking strength. Neither the area loss nor the number of broken wires measured from nondestructive tests could be used as clear indicators of the loss of strength. However, it was found from the tensile tests for both rope specimens that the strength loss was associated with the reduction of breaking strain. This suggests that measuring the strain of many short sections of a rope in the elastic region may locate the high stress sections and thus delermine the condition of the rope.

Jan 1, 2010

By Joseph J. Wallace

1. The investigation shows that nine coal beds have been mined in Harlan County, of which the Harlan and Upper Elkhorn No, 3 are the most important from the standpoint of present production. Of less importance are the Hindman, Flag, Haddix, Wax, Fire Clay, Armburgy, and Upper Elkhorn No. 2. The Harlan, Upper Elkhorn No. 3, and Upper Elkhorn No. 2 beds contain the largest remaining known reserves. 2. Known measured and indicated reserves in all beds, based on a minimum thickness of 14 inches and 1,800 tons per acre-foot of coal in place, are estimated at 2,138 million short tons as of January I, 1932. Of this total, 1,956 million short tons is in beds 28 inches and more thick. Areas in each bed were omitted from the estimate because available data relative to the bed characteristics are too meager for making an estimate that conforms with the definitions of measured and indicated coal adopted for this study, Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.

Jan 1, 1954

By William W. Adams

The stone-quarrying industry of the United States, including such related operations as rock crushing, rock dressing, and the manufacture of cement and lime, reported a larger volume of employment in 1934 than in 1933. Reports from the operating companies to the United States Bureau of Mines showed an increase in the number of men employed, number of man-days of employment, and total number of man-hours of labor performed during the year. Moreover, the average worker had a longer period of employment during 1934, the gain amounting to 11 percent over 1933. The increase in employment was accompanied by no increase in accidents for the industry as a whole; in fact, the accident rate for 1934 was a fraction lower than the rate for 1933. In some branches of the industry the frequency of accidents increased, but these increases were more than offset by reductions in rates for other branches. Reports for 1934 were received from 1,403 active plants. The working force averaged 64,331 men for 204 days per man, and the total period of employment for all of the men was 95,258,880 man-hours. Each employee averaged 1,481 hours of work during the year. The total number of hours of labor represented a gain of more than 8 percent, and the average working time per employee showed a gain of 62 hours per man.

Jan 1, 1936

By Jay F. Colinet

Longwall mining in lower seam heights may necessitate the use of single-drum shearers to overcome size constraints associated with standard double-drum shearers. To avoid the operational problem of clearance in the tailgate entry with one single-drum shearer, two single-drum machines can be operated on the same face, with each shearer responsible for mining a predefined portion of the face. However, utilization of two shearers on the same face necessitates the positioning of one shearer operator and a jacksetter in the return air of the upwind shearer, thus complicating respirable dust control on the longwall. In an effort to evaluate the unique dust control problems associated with this type of mining, the U.S. Bureau of Mines conducted dust surveys on two multiple-machine longwall operations. Sampling was done to quantify major sources of respirable dust and to identify potential solutions to problem areas. Sampling results indicate that the cutting sequences utilized on multiple-machine faces may have to be designed to minimize dust exposure, as opposed to optimizing productivity or facilitating operational requirements. Also, state-of-the-art dust control techniques typically found on double-drum shearer longwalls must be employed to help minimize the exposure of all face personnel to traditional dust sources.

Jan 1, 2010

By John A. Breslin

This report summarizes the principal activities and significant results of the Bureau of Mines respirable dust research program since passage of the Federal Coal Mine Health and Safety Act of 1969 and the Federal Mine Safety and Health Amendments Act of 1977. This program has investigated new and improved techniques and equipment to reduce or prevent the formation of dust during the cutting cycle; to dilute, suppress, or collect airborne dust generated during mining, handling, and processing; and to improve the measurement of dust levels for evaluation of engineering controls and for enforcement of Federal dust standards. The report is intended for mining industry dust control specialists and other interested parties. It includes a brief summary of the program to date, a section on future research plans and goals, and a list of publications resulting from the Bureau's respirable dust program.

Jan 1, 1982

By D. Harrington

The placing of much, sometimes practically all, of the burden of the expense of mine accidents on the shoulders of the mine operator by compensation laws, and the fact that the problem of protecting the life end limb of workers is now by public opinion largely if not wholly passed to each industry to solve (and present-day thought strongly supports the justice of both of these propositions), are forcing industrial organizations into accident-prevention. Work. This policy is being adopted not alone to protect the companies; in addition, executives alert to their opportunities and obligations are taking part in this work personally to protect themselves. The functions of industrial executives in accident-prevention work are becoming numerous and complex. Executives who are logical in their reasoning, quickly see that before a company can constantly ask or expect the workers to heed safety suggestions, the company and its officials must "put their house in order" by laying down a concrete, definite safety program. For mines this includes primarily adoption of a to a logical mining method, the installation of safe miming equipment and practice the netting forth in definite form (preferably do a printed pamphlet) of the company's minimum safety requirements, and the organization of its operating officials into an accident-prevention body. After the company has its own affairs so arranged that it can go to its workers with "clear, hands" in promoting a safety program, the real work begins; and this is especially applicable in mining.

Jan 1, 1939

By Emory Smith

The Victorville cement plant of the Southwestern Portland Cement Co. is located about 1 mile from the city of Victorville, Calif. Two transcontinental railway systems, the Atchison, Topeka & Santa Fe, and the Southern Pacific Railroad, afford shipped facilities. The plant is modern and well kept, as the officials, especially the higher operating officials, take pride in the appearance of the place. Dust has been practically eliminated by the installation of dust collectors and wet grinding. The plant has a rated capacity of 5,000 barrels of cement daily.

Jan 1, 1929

By Sidney Speil

In the study of clays and related minerals, the analytical techniques commonly employed in mineral analysis are not always applicable. The X-ray examination of a clay sample usually will show the major constituents, but often minor· clay impurities will not be detected because of line broadening and the similarity of the main lines of clay· mineral diffraction patterns, The petrographic analysis of clay minerals with clay particles as small as a few microns is usually difficult. With still smaller particles, a gross effect often is noted in which a mixture of several constituents gives the appearance of a single constituent with the mean optical-characteristics of the mixture. 3/ The electron microscope has recently been used to study clay particle shapes of various aluminosilicates. 4/ However, this method has not yet been sufficiently explored. The Chemical method in which a mineralogical analysis is calculated from the oxide chemical analysis has been discussed by Wilson 5/ and others, and many of the shortcomings have been pointed out. It should also be recognized that the variable alkali and alkaline earth content of bentonites makes it inaccurate to assign these basic elements arbitrarily to feldspar or mica in any clay that contains appreciable bentonite.

Jul 1, 1944

By Joseph J. Wallace

The 1952 Annual Report of the West Virginia Department of Mines lists seven beds that are being mined in Mingo County, of which the Cedar Grove is the most important. The Cedar Grove, Alma, and Coalburg contain the largest remaining known reserves. 2. Known measured and indicated reserves in all beds, based on a minimum thickness of 14 inches and 1,800 tons per acre-foot of coal in place, are estimated at 3,007 million short tons as of January 1, 1953. Of this total, 2,396 million short tons is in beds 28 inches and more thick. Areas in each bed were omitted from the estimate because available data relative to the bed characteristics are too meager for making an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.

Jan 1, 1954

By Secretary of the Interior

"INTRODUCTION The Bureau of Mines Synthetic Liquid Fuels Program again forged ahead during 1952, and important technical advances led the way to improved methods of converting coal and oil shale into liquid fuels. Marking the eighth year of activities under this program, the past 12 months brought a new domestic industry nearer realization.The increasing demand for gasoline and oil and the rising cost of finding new petroleum, coupled with America's growing dependence on imports and the unsettled international situation, have continued emphasize the importance of the Bureau's Synthetic Liquid Fuels Program. Oil, the indispensable material of wartime, likewise has critical importance in peacetime, touching as it does the life of every individual. Supplementing petroleum with synthetic liquid fuels will not only conserve this Nation's petroleum reserves but also will bring into greater use its tremendous reserves of coal, as well as the vast deposits of oil shale for which no other practical use has yet been found.The Bureau of Mines Synthetic Liquid Fuels Program is one of the most important and far-reaching of the Government's research projects. Through development, of commercial synthetic liquid fuels, the United States can obtain oil products from its great inland reserves of coal and oil shale to supplement petroleum in any quantity that may be necessary, consistent with economic and other requirements, such as national defense. The use of raw materials from such deposits would be of highest importance in wartime, when shipping lanes are menaced by the enemy. The Synthetic Liquid Fuels Program of the Bureau of Mines and research efforts of industry have advanced American technology to the point where it is now possible to begin the design and construction of prototype plants. Certainly, significant improvements will be made as the program continues, but this prospect in no way alters the fact that the start of prototype plants should be encouraged. These plants, as the first step in the development of a synthetic fuels industry, would serve a threefold purpose:"

Jan 1, 1953

By E. R. Andersen, F. E. Block, T. T. Campbell

This work was done to develop methods for increasing the yields and purity of vanadium prepared by bomb reduction of vanadium compounds . Compounds reduced were V₂ 05 , V203 , VC , and VC13 . Sodium , calcium , and magnesium were used as reductants . Variables considered included reductant form , bomb size , pressure during reaction , method of ignition , and the use of slag fluidizing additives . It was concluded that yields of 85 to 90 percent can be effected by the calcium reduction of V205 in reactors measuring as much as 14 inches in diameter and 60 inches in height . Optimum charge composition included V₂05 , 65 percent excess calcium , and 0.4 moles sulfur per mole vanadium . Purity of the vanadium produced in large reactors varied from 99.5 to 99.8 percent . The higher purity metal , depending upon the amounts of interstitial impurities present , was usually cold ductile . Although high yields of up to 99.5 percent can be effected by bomb reduction of VC1 , the high pressures developed in the bombs and attack of the reactor walls by the byproduct chloride slags discourages this method of preparing vanadium . It was found that significant purification of impure regulus metal occurred when it was hydrided , crushed , acid leached , and vacuum dehydrided . Metal so treated can readily be converted to ductile sheet . A cost estimate based on the production of 100 tons of vanadium per year was prepared . It was concluded that pure ductile vanadium could be produced for approximately $ 20.00 per pound .

Jan 1, 1964

By Walford S. Wright, NORMAN EBBLEY

During the past decade (1937 to 1947), including the war years of heavy demand for metals, the United States realized about one-eighth of its antimony requirements from domestic production, chiefly in Alaska. In World War II, our foreign supply sources became endangered; and uncertainty in our Far Eastern supply made this nation focus on Alaska’s mineral resources with a Production Gear that centered in the Bureau of Mines experimental station at College (Alaska). The development work known as District or central deposits. The strategic mining districts included that of central Alaska was reorganized at Ketchikan Mining Districts. Mines were located here had produced considerable quantities since 1901; but methods for exploration had come from 1936 to spring 1942, some $4 million produced in gold alone. Statistics relating to available ores are those selected by type and exploitation periods with wide variety applied. During the summer of 1941, as part of an extensive Geological Survey program continuing through funds provided by U.S., geological surveys spent six weeks mapping an area approximately two square miles surrounding mines. The mines working both surface & underground work employed these men in mapping exercises.

Jan 1, 1948

By Charles G. Maier

"INTRODUCTION The use of thermodynamic calculations to answer practical problems in metallurgy, especially those that are relatively difficult to test experimentally, is rapidly becoming a conventional method of procedure. Nevertheless, these methods cannot he applied effectively until the fundamental thermodynamic constants used for them have become available either by direct experiment or by recalculation of data already existing in more or less undigested form.In an attempt to collect such data far the compounds of lead and the antimony group the incentive has been to make a preliminary survey that will disclose the gaps or questionable phases of available information and to collect data that may be used to answer certain rather practical problems presented by operating metallurgists.This report comprises three sections; the first gives the basis of selection of the constants which may now be given or estimated, and the later sections discuss the application of the figures obtained to two of the more interesting problems.The reader will discover that many of the quantities involve critical study of a number of more or less discordant observations. Although certain data could be rejected on the basis of thermodynamic comparisons, it must not be overlooked that many of the figures are the results of rational estimates rather than exact experiment. The use of thermodynamic methods to control and partly authenticate such estimates is one of its most valuable characteristics for the practising metallurgist or chemist, who cannot check by direct experiment each property of the materials which he converts to usable form.Nevertheless, while it is definitely possible in certain instances that the final figure selected for the heat or free energy of a process or substance may be in error by as much as a few hundred to a few thousand calories per formula weight, questionable figures are usually revealed by the thermodynamic calculations made. When quantities of such degree of accuracy are, and they often must be, used for estimating an unknown reaction, the result often gives no more than the order of magnitude of the desired quantities. Yet even in these extreme cases the answer is far more reliable and valuable than an unordered guess or a conclusion based on incorrect data."

Dec 1, 1934

By J. H. East, D. Harrington

"INTRODUCTION Burning refuse dumps are a common and by no means pleasant sight in most coal-mining distracts; they have been and largely continue to be accepted as a necessary, if undesirable, adjunct to coal-mining operations. The odor, smoke, and fumes emanating from the burning dumps have caused much property damage, as well as aroused unfavorable public sentiment in the areas thus affected; and there is reason to believe that, in at least some cases, they have had an adverse effect on the health of certain communities, adjacent to mines. In some instances such communities have been owned or controlled by the mining companies and in others they are incorporated towns.After the start of World War II, it was necessary for Great Britain to take prompt and effective measures to extinguish or at least blanket the burning refuse dumps at collieries, since the fires served as beacons for the enemy planes; the problem thus became a matter of national security rather than one of local inconvenience. If the United States should become involved in a bombing war, these dumps might became a source of national danger, hence now is a propitious time to at least make a start on available methods of solving this problem. Much progress was made in Great Britain in extinguishing the dump fires that had burned for years and in preventing newly made dumps from taking fire.Burning refuse dumps have not been a national problem in the United States, but they are a nuisance and frequently a danger and often a fruitful cause of poor public relations on account of the odor and fumes. Many progressive coal-mining companies are taking effective and positive action in trying to extinguish old dump fires and to build new dumps so they are less likely to fire.The purpose of this paper is to provide information about the problem as well as on ways to extinguish refuse dump fires, to describe methods of constructing dumps that probably will prevent them from firing, and to point out some of the danger that exists when dumps are improperly built and when they are on fire."

Mar 1, 1948

By David Schlain

"IntroductionThe purpose of this investigation was to study the characteristics of the high-acid electrolytic manganese cell with the idea of fitting it into one of the flow sheets being worked out by the Metallurgical Division of the Bureau of Mines for the recovery of manganese from low-grade domestic ores.In construction, the high-acid cell 3/ differs from the low-acid type in that the cathode and anode compartments are separated by a diaphragm of relatively low porosity, such as alundum. This is necessary because in the high-acid cell the two electrolytes are circulated separately. The anolyte is 15 to 30 percent H2SO4. The catholyte consists of a solution of ammonium sulfate and manganese sulfate with a OH of 4 to 3. The only mixing of electrolytes is that resulting from flow through the diaphragms. In the low-acid cell the two electrolytes are not circulated separately and do not differ so widely in hydrogen-ion concentration. Hence, the canvas diaphragm is sufficient.During operation of the cell, manganese is deposited on the cathode, and sulfuric acid is produced in the anode compartments. Various other reactions take place in the cell. There is considerable decomposition of water; hydrogen is evolved at the cathode, and oxygen is liberated at the anode. When lead anodes are used, some hydrated oxides of manganese are formed at the anodes. The quantity of oxides formed is not as great as it is in the low-acid cell, because fewer Mn++ reach the vicinity of the anodes."

Jul 1, 1942

By R. E. Heithecker, D. B. Taliaferro

"INTRODUCTION Recovery of core specimens from subsurface formations and their subsequent analysis are important aids in efficient development and operation of oil and gas fields. Gore specimens first were obtained mainly for the geologic information they revealed; now they are analyzed to determine many of the physical characteristics and conditions of the subsurface formations as well. Cores recovered from the producing formations may be analyzed for porosity, permeability, oil content, ""connate"" water content, and other physical and chemical properties of the formation, all to the end of furnishing enough data for making reliable estimates of the quantity and avail¬ability of oil and as within a reservoir and in devising efficient means for their withdrawal.Examination of bottom-hole samples of oil gives valuable information concerning the amount of gas in solution in the oil within the reservoir and the resultant shrinkage of the oil when the gas is released. Producing characteristics of reservoirs nay be determined by means of subsurface pressure and temperature gages and measurements male at the wellhead; however, unless reliable core analyses are available, these data have only limited use in any quantitative study of reserves. In such a study the quantity of oil, gas, and water contained in a unit volume of the reservoir formation is extremely important. Although reliable methods of analyzing cores have been developed and the data thus obtained are valuable, their applications become more limited or reservoirs at higher temperatures and pressures are discovered. This condition results almost entirely from the fact that in recovering a core from a formation of high pressure and temperature by present methods a large part of the fluid content of the core is lost or contaminated to an unknown extent. For a number of years most petroleum engineers have held that if this loss and contamination of the fluid content of a core were eliminated, the value of core analyses would be increased greatly."

Nov 1, 1939

By Daniel E. Sullivan

This Bureau of Mines publication examines the potential impact on minerals of the tariff and nontariff agreements that resulted from the Tokyo Round of the Multilateral Trade Negotiations, which were conducted under the auspices of the General Agreement on Tariffs and Trade. These agreements will affect minerals by reducing tariff levels and by changing rules by which they are traded internationally.

Jan 1, 1981

By J. R. Ruark

Because of the importance of oil-shale reserves the Bureau or Mines resumed research investigations in this field beginning in 1944. The Bureau early decided to build a Large-scale demonstration plant to accomplish the dual purpose of obtaining design data and to produce crude shale oil for refining studies. Two 40-ton-Capacity batch N-T-U (Nevada-Texas-Utah) retorts were completed for this purpose in 1947. After a preliminary operation, the plant was used to investigate process variables of air rate, recycle gas rate, and shale particle size and crude. Correlations obtained from these variables are presented in this report. Researchers concluded that recycle gas was not necessary for efficient operation of the process. Short comings of the batch method of processing the oil shale are pointed out in the report. Several periods of prolonged production operations were carried out. During these periods, the retorts were operated to produce as much crude oil per day as possible. The lifetime operation of the N-T-U retorts was divides into three periods, namely, preliminary operation, process variable study, and production operation. During the preliminary operation, 187 runs were made with a total of 7,596 tons of raw shale used to produce 3,688 barrels of crude shale oil. During the process variable study, 179 runs were made with a consumption of 7,494 tons of raw shale and a production of 4,218 barrels of crude shale oil. The production operation consisted of 554 runs in which 22,457 tons of raw shale was used to produce 12,359 barrels of crude shale ail. The overall total for the lifetime operation of the retorts consisted of 920 runs with a total consumption of 37,547 tons of raw shale and a production if 20,265 barrels of crude shale oil.

Jan 1, 1956