Search Documents

By F. K. McIntosh, L. A. Dahmers

"INTRODUCTION North Carolina has been the leading producer of mica in the United States, accounting for roughly 50 percent of the Nation's output. The producing area is a belt some 100 miles in width lying in the Mountain and Piedmont sections in the western part of the State. Ashe, Watauga, Avery, Mitchell, Yancey, Buncombe, Haywood, Jackson, Macon, Transylvania, Rutherford, Cleveland, and Lincoln Counties supply the bulk of production, while small amounts have been produced in Gaston, Catawba, Burke, Wilkes, Yadkin, Stokes, and Person Counties.To assist the operators and expedite the production of mica during the recent emergency, the Bureau of Mines drilled four of the more promising mica properties in this State. The results of this exploratory program are recorded in this report.ACKNOWLEDGMENTSIn its program of investigation of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each project as soon as practicable after its conclusion. The Mining Division, L. B. Moon, chief, conducts preliminary examinations, does the actual investigative work, and prepares the final report. The Metallurgical Division, O. C. Ralston, chief, analyzes samples and makes beneficiation tests."

Apr 1, 1948

By M. R. Geer

This report presents the results of washability examinations of seven coals from the principal coal-producing fields of Montana. A complete performance test of the Baum-type jig operated at one of the mines is included, as are the results of cleaning tests made on two of the coals in a dense-medium pilot plant. The coals examined from the Red Lodge, Bull Mountain, and Forsyth fields are comparatively easy to clean. Ash contents of 5 to 10 percent can be obtained at yields of washed coal ranging from 90 to 95 percent. The coal from the Great Falls field, however, could not be cleaned readily to less than 14 percent ash, and the rejection of impurity would amount to over 25 percent. The two coals treated in the dense-medium pilot plant were characterized by sharp separation of impurity, high recovery efficiency, and satisfactory reduction in ash content.

Jan 1, 1955

By Wm. W. Adell

"These hydrocarbons belonging to the same chemical series as methane, having the general formula CnH2n have many chemical properties in common with methane and their addition to a lean gas charges the properties and burning characteristics of the gas in the same general direction although to a different extent. The hydrocarbons of this series do not readily enter into chemical reaction with other substances and therefore are incapable of combining with oxygen or polymerizing in the disturbing system and thus cannot cause gum and room troubles commonly met with in the distribution of manufactured gas.As the number of carbon atoms in the molecule increases, i.e. in proceeding from methane throughout the series, the oxygen requirements for the complete combustion of unit volume of the gases also increases; in other words, the calorific values of these hydrocarbons (as gases) increases from methane. Similarly the specific gravity increases from methane in the same order. In Table 1 are shown some of the physical constants and properties of a few of these hydrocarbons which hive bearing on their use for enriching gas."

Nov 1, 1927

By V. B. Royer, C. H. Harty

"MANGANESE-SILOCON ALLOYS AS DEOXIDIZERSThe basic open-hearth process for steel mining requires large amounts of oxidized iron for oxidation of the elements carbon, silicon, manganese, and phosphorus which are to be removed from the metal. Some of this oxidized iron (FeO) dissolves in the metal during the refining process, Subsequent to the elimination of the elements named, a considerable amount of dissolved iron oxide must be removed before the metal may be cast into ingot form. The elements generally used, for iron oxide removal, or deoxidation, are silicon, manganese, and aluminum. Silicon and manganese are always alloyed with iron, either singly or in combinations of various compositions. Aluminum generally is used in a commercially pure state and sometimes in complex alloys. A double deoxidizer of manganese and silicon alloyed with iron for furnace deoxidation has been the subject of an extensive cooperative investigation between the United States Bureau of Mines, the Carnegie Institute of Technology, and the Metallurgical Advisory Board. Certain grader of steel, especially low-carbon rimming steels, require a low-carbon deoxidizer to keep the finished steel within the carbon specification after deoxidation. ACKNOWLEDGMENTThe authors wish to acknowledge the assistance of J. F. Sanderson and S. S. Johnston in the analysis of the alloys used in this work.PURPOSE OF WORKThe need for definite information as to which compositions of manganese and silicon within a certain manganese-silicon ratio and when alloyed with iron would have an allowable carbon content for the particular grade or type of steel on which the deoxidize is used, prompted the undertaking of this investigation to determine the solubility of carbon in manganese, silicon, and iron alloys within the region bounded by 10:1 and 4:l manganese to silicon ratios. These data should be of value to the manufacturer producing such"

May 1, 1934

By William H. King

Preliminary examination of the Virgin River manganese deposit was made by C. H. Johnson, Bureau of Mines engineer, in March 1941. During, April and May 8 trenches were dug, a 48-foot inclined shaft was sunk, and 719 linear feet of channel samples were cut. McKelvey and Wiese, of the Federal Geological Survey, completed mapping the deposit, including the entire area of overlying formations comprising the point of land between the outcrop and Lake Mead. The geologic maps, maps, and ore estimates resulting from these examinations formed the basis for a preliminary report by C. H. Johnson, who recommended further exploration by diamond drilling.

Jan 1, 1949

By George A. Morgan

The 53 countries that constituted Africa in 1990 accounted for a significant portion of total world output of a number of mineral commodities. Among the most significant to be produced in Africa were andalusite, antimony, asbestos, bauxite, chromite, coal, cobalt, copper, diamond, fluorspar, gold, lithium minerals, manganese, phosphate, platinum-group metals, the titanium minerals-ilmenite and rutile, vanadium, vermiculite, uranium, and zircon. Several of these, chromite, cobalt, diamond, and manganese, were not produced in the United States. Despite the underdevelopment of much of Africa, mineral raw materials playa very important part in the national economies of many of its countries. In many cases, the production of minerals is the dominant economic activity in the country, often having the largest and most sophisticated work force. In several countries, one or two mineral commodities are dominant in a weakly diversified economy. Among these are petroleum and diamonds in Angola, petroleum in the Congo, gold in Ghana, bauxite in Guinea, uranium in Niger, phosphate in Senegal and Togo, and copper and cobalt in Zaire and Zambia.

Jan 1, 1992

By J. W. Thompson

SALE AND CONVEYANCE. DEED BY INDIAN ALLOTTEE OF UNSOUND MIND-BONA FIDE PURCHASER. The deed of an Indian allottee whose mind was unsound, but who was not entirely without understanding, is voidable if made before the grantor's incapacity has been judicially determined; and a purchaser of the original grantee who interposes the defense of a bona fide purchaser has the burden of showing a purchase for value and on failure to do so can not claim the benefit of a bona fide purchaser. Adams Oil & Gas Co. v. Hudson (Oklahoma), 155 Pacific, 220, February. 1916. PURCHASER OF MINING CLAIM-RIGHT TO FIXTURES. The purchaser of a mine equipped with an electric hoist, placed in the mine under a rental contract with the owner of the hoist and under an agreement to return it to the owner at the expiration of the term of hiring, can not claim and hold the hoist as against the owner where the agent of the seller explained to the purchaser that the hoist was not owned by the owner of the claim. Montana Electric Co. v. Northern Valley Mining Co. (Montana), 153 Pacific, 1017. p, 1018, October, 1915. AUTHORITY OF GRANTEE TO EXTEND LEASE. A deed conveying lands subject to an oil and gas lease under which the lessee had the right to drill or pay money in lieu of drilling at his option, and reserving to the grantor a share of the royalties under such lease, and expressly authorizing the grantee to lease the land for oil and gas purposes and to take the rentals, authorizes the grantee to extend the existing lease before the expiration thereof in consideration of the annual payment of money in lieu of drilling, as contemplated by the lease.

Jan 1, 1916

By W. R. K. Wu

This bulletin traces the development of high-pressure, coal and tar hydrogenation technology, based on an intensive review of the pertinent literature. The bulletin was written as a part of the Bureau of Mines research program on synthetic liquid fuels. It covers the history and economics of the process; the chemical aspect of hydrogenation of coal, tar, and middle oil; the engineering aspect of converting coal and tar to liquid fuels, principally gasoline; and the equipment for the process. The literature covered includes documents of the United States and British Governments, journals, and other publications. Bureau results in the hydrogenation field are also incorporated.

Jan 1, 1968

By David C. Grant

In situ uranium mining offers the advantages of minimal environmental disturbance, low capital and operating costs, and reduced mining development time. It is becoming an increasingly attractive mining method for the recovery of uranium from secondary ore deposits. In order to better understand the process, a laboratory technique was developed and used to study and simulate both the chemical and physical phenomena occurring in ore bodies during in situ leaching. The laboratory simulation technique has been used to determine effects of leaching variables on permeability uranium recovery, and post-leach aquifer restoration. This report describes the simulation system and testing procedure in sufficient detail to allow the construction of the system, and to perform the desired leaching tests. With construction of such a system, in situ leaching of a given ore using various leach conditions can be evaluated relatively rapidly in the laboratory. Not only could optimum leach conditions be selected for existing ore bodies, but also exploitation of new ore bodies could be accelerated.

Jan 1, 1985

By J. W. Hunter, J. H. Jacobs

"Approximately 355 tons of nodules from Chamberlain; S. D., ore were processed in the 1-ton-per-day electrolytic-manganese pilot plant of the Bureau of lanes at Boulder City, Nev., in a continuous 3-month operation. The ore, ground to minus 48-mesh, was found to be amenable to leaching with acid directly or after roasting under reducing conditions in a Skinner muffled multiple-hearth furnace.Unroasted ore gave an acid-leach extraction of 84 to 88 percent of the manganese, which after neutralization showed an over-all extraction of between 81 and 85 percent of the manganese. The amount of iron extracted varied, but it was always,enough to permit the use of ammonia for neutralization.Roasted ore showed an acid-leach extraction of 89 to 91 percent of the manganese. A large amount of iron went-into solution, so that it was not economical to neutralize it entirely with ammonia. By neutralizing with calcine to a pH of 5.0 and completing -neutralization with ammonia to a pH of a.5 an over-all manganese extraction of 84 to 86 percent was obtained. The slight increase in. extraction on roasted ore probably would not justify the cost of roasting.Acid consumption averaged 1.75 pounds per pound of manganese extracted. Settling rates of the residue in leach solution were to slow to permit clarification in thickeners, but a Moore vacuum leaf filter proved to be satisfactory. Purification of raw leach solution was .accomplished readily by hydrogen sulfide with a low gas consumption. Electrolysis was normal, without difficulty, and with -current efficiency ranging between 62 and 66 percent.The use of Chamberlain modules for the production of electrolytic manganese would result in an operating cost of 0.8316 cent per pound higher than the cost of producing electrolytic manganese from Three Wids ore."

Mar 1, 1946

By C. Özgen Karacan

Gamma ray, density, sonic and core logs obtained from two boreholes drilled over a longwall panel in Southwestern (SW) Pennsylvania were analyzed for formation boundaries, log-derived porosities and densities and for rock elastic properties from sonic transit times. Gamma ray (GR) and density logs (DL) were analyzed using univariate statistical techniques and fractal statistics for similarity and ordering of the log data in depth. A Fourier transformation with low-pass filter was used as a noise elimination (filtering) technique from the original logs. Filtered data was tested using basic univariate and fractal statistics, rescaled range (R/S) and power spectrum (PS) analysis to compare the information characteristics of the filtered logs with the original data. The randomness of log data in depth was analyzed for fractional Gaussian noise (fGn) or fractional Brownian motion (fBm) character. A new prediction technique using radial basis function (RBF) networks was developed to calculate shear and Young?s moduli of the formations when sonic logs are not available. For this approach, the filtered logs were used as input to an RBF based upon a combination of supervised and unsupervised learning. The network was trained and tested using rock elastic properties calculated from the sonic log of one of the boreholes. The network was used to predict the elastic and shear moduli of the coal-measure rocks over a longwall coal mine in SW Pennsylvania. This approach demonstrated that it could be used for prediction of elastic and shear moduli of coal-measure rocks with reasonable accuracy.

Jan 1, 2009

By Frank L. Hess

"New England" and "granite" if not synonymous are at least associated terms. Where there are granites that are not deeply eroded there are usually pegmatites, the most erratic of rocks, and of them New England has a full portion. Many of the New England pegmatites contain the rare alkalis - lithium, rubidium, and cesium. however, the same in homogeneity of the earth's crust that has made the New England pegmatites unusual, in that so many of them contain the rare alkalis, has likewise made the distribution of the rare-alkali minerals sporadic even in those pegmatites, and most contain only enough to furnish collectors with more or less ornamental and uncommon minerals. New England has long had numberless collectors of minerals, and the mineralogists of its various schools have published many papers on the pegmatitic minerals, including those of the rare alkalis, but none of the papers have dealt with estimates of quantities. In this paper we have tried to place the emphasis on quantity rather than on mineralogy.

Jan 1, 1943

By M. A. Cook

Crude titanium metal, produced by the reduction of titanium tetrachloride with magnesium, is contaminated with some excess magnesium end adhering magnesium chloride when it is removed from the reaction pot. The method of vacuum 'purification is described in which the crude mixture is heated in a vacuum at a temperature of about 1,700° F. and the magnesium metal and chloride are volatilized away from the titanium, leaving it practically magnesium-free in a sponge-metal form. The pilot-plant equipment is described in detail, together with the technique of operation and methods of sponge recovery. Operating data is given, which compares ten 24- to 30-hour heats with ton 48-hour heats, and finally, power and labor requirements are discussed. Vacuum purification of raw titanium produced by the Kroll process has boon employed for treating of several tons of raw titanium with results for superior to those achieved by the method of leaching and grinding. The operations described, while on but little more than pilot-plant scale, indicate commercial feasibility of the process, even though it is a batch-typo operation. All equipment is either of standard manufacture or can be readily fabricated from standard materials, and operation of the units can be satisfactorily maintained by semiskilled labor.

Jan 1, 1952

By L. M. Adams

Experiments in reclaiming acidic surface-mined coal lands with raw fly ash from bituminous-coal-fired powerplants were conducted by the Bureau of Mines at two sites in northern West Virginia. Plots at both sites were treated with varying tonnages of fly ash from three area powerplants and were planted with a variety of grasses, legumes, trees, and shrubs. Eight grasses and seven legumes were investigated. Greatest promise for growth under harsh soil conditions was shown by Kentucky 31 fescue, rye and red top grasses, and birdsfoot trefoil, a legume. Survival of trees and shrubs was negligible. Addition of fly ash to the spoil increased the pH to a range tolerable to some types of plant growth, improved the texture of the soil, and increased the available water of the resulting mixture.

Jan 1, 1971

By C. A. Herbert

Coal-mine explosions in the United States during the past 10 years ranked third among the causes of coal-mine fatalities and constituted 16.1 percent of the total fatalities. In Indiana, however, during this same period the percentage of fatalities from this cause was much higher than the average percentage for the entire country. It is only through knowledge of the factors that have led to these past explosions that intelligent steps may be taken to prevent similar occurrences in the future. Although information concerning many of the earlier explosions is lacking, an attempt has been made to tabulate the information available in the hope that it may be of assistance in calling attention to some of the principal causes of explosions in Indiana.

Jan 1, 1934

By L. J. Defferding

This report documents the work performed by Battelle-Northwest and its sub-contractors in Phase I of a project to develop a cross pit conveyor system for the Bureau of Mines. The conveyor system description includes details of the conceptual design as well as system and component specifications. The selection of primary and back-up sites for system demonstration is discussed. Maneuvers and operating sequences required for mining the selected demonstration site are described and illustrated in detail. Economic viability of the cross pit conveyor system was analyzed by estimating the cost of overburden removal per ton of coal using the Battelle-designed concept and comparing these costs to the cost of an available state-of-the-art 30-yd3 dragline operation. Testing and trade-off studies conducted are documented and the results presented. Alternate designs considered in developing the selected cross pit concept are included for completeness. Based on the evaluation of the selected concept, it was concluded that the cross pit conveyor system proposed by Battelle is a technically and economically feasible overburden handling method with a good potential to improve western coal mining efficiency.

Jan 1, 1976

By Richard A. Watson

A frequency-shift keying (FSK) modulator-demodulator (modem) network has been devised for the Bureau of Mines mine-monitoring systems. This network permits an unlimited number of remote stations to communicate with one central station over the same pair of wires. The network operates at a speed of 4,800 Bd at distances up to 5 miles. This report describes the development and operation of the modems. The theory of operation, schematic diagrams, and printed circuit board layouts are provided. Although the modems were built for a specific application, a more general use is discussed whereby the network would operate with a typical serial channel format.

Jan 1, 1985

By J. A. Kosek

Work has been carried out under Bureau of Mines Contract HO 395132 to develop improved sensor cells for use in direct-reading detectors and diffusion exposure meters. A pumped CO sensor cell was developed which has a shorter response time, improved temperature cycle characteristics, and improved linearity and stability at high CO concentrations. Diffusion CO sensor cells have shown good response level stability and linearity up to 1000 ppm. In addition, a new sensor cell catalyst has been developed for NO2 sensor cells which has a much shorter response time and improved response stability characteristics.

Jan 1, 1982

By G. W. Murrie

A geologic study of the Mary Lee Group of coalbeds in the Black Warrior coal basin was undertaken to examine coal stratigraphy and determine regional trends and extent of the coalbeds. The area investigated encompasses 835 square miles in Jefferson, Walker, and Tuscaloosa Counties, Ala. More than 700 core logs were used to construct a structure map, coal, interval, and overburden isopachs, and cross sections. There is evidence that structure affected sedimentation. Coalbed isopachs indicate the Mary Lee Group was deposited in fluvial-deltaic and low-lying coastal plain environments. The Mary Lee coalbed is the only coalbed which is continuous throughout the area, commonly with two benches which have a combined thickness of 2 to 12 feet. The Mary Lee coalbed changes rank in the basin from high-through medium-to low-volatile coal. The methane gas potential of the Mary Lee Group coals is estimated to be greater than 1 trillion cubic feet. There is an excellent correlation between the orientation of surface cleats with those measured underground in the Mary Lee coalbed. The face cleats roughly parallel the axes of the area's folds and trend northeast-southwest.

Jan 1, 1976

By Lloyd A. Morley

This annual report details progress under USBM Grant G0155003 during the project period of January 1, 1977 through December 31, 1977. The report contains four principal chapters covering accomplishments in the mine electrical safety research areas of continuous monitoring, battery and battery-charging safety, and computer modeling. Highlights of the work are summarized in the last report chapter.

Jan 1, 1978