Search Documents

By H. B. Hill

The discovery of the Oklahoma City field and its rapid development into one of the major oil-producing districts is an outstanding epoch in the history of the petroleum industry not only of Oklahoma but also of the United States. The relatively great depth to which the wells were drilled and the large initial production of high-gravity oil are of special significance. The field has boon under proration almost from the time that its development began, and many new production problems have developed out of the changed conditions of operation. The discovery well was first tested in December 1928 at a depth of 6,402 feet, with an initial production of 4,847 barrels of 38,5.° A.P.I. gravity oil, and several months later was, completed at a depth of 6,624 feet, The large initial production, the high pressure, and the large gas volume in the different horizons of the discovery well suggested the potential possibilities of gas and oil, production in formations of Pennsylvanian and pre-Pennsylvanian age.

Jan 1, 1933

By Naoki Hosoya, Setsuo Maeda

This paper addresses establishment of an experimental system for measuring biodynamic response (BR) of hand-arm system at the NIIH in Japan. BR measurement system at the NIIH is nearly equivalent to NIOSH installed system. The feasibility of the system is examined through the apparent mass (AM) measurement of the empty handle and a set of calibration masses. Apparatus The grip force was measured by using the handle shown in Fig. 1. The handle has two force sensors (KISTLER, 9212) and one accelerometer (PCB, 356A12). A low-pass filter with 5 Hz cut-off frequency was used to the grip force from measured force signal. Figure 2 shows BR measurement system in this study. The push or pull force at the handle was measured by using the force plate (KISTLER, 9286AA). The grip force and the push / pull force were displayed on a monitor. The shaker (IMV, VE-100S) is used to vibrate the hand-arm system along the forearm axis (Zh direction) (ISO 10068, 1998; ISO 5349-1, 2001). In most situations force actions for operating tools are expressed by grip, push, pull and combined these actions. These actions can be simulated in the test system. AM was obtained by performing H1 estimator in the PULSETM system (B&K, 3109) and it is denoted at the one-third octave band center frequencies. [ ] Methods In order to investigate the reliability of the system, AM measurement of the handle was performed. It is assumed that the handle is rigid in the upper limit of adoptive frequency range in this study. This assumption is validated in AM measurement of the empty handle. A pseudo-random vibration in the frequency range of 10 to 1,250 Hz was used and its amplitude is 1.0 (m/s2)2/Hz with a flat power spectral density (PSD) in the experiment. Measured AM includes the mass effect of the measuring cap in a subject experiment. Compensated apparent mass AMc(?) is obtained by Eq. (1) 1-2.

Jan 6, 2006

By Sidney Katell

This report covers the period January 1964 through December 1964; it is a continuation of the series that began with the publication of Information Circular 7516 in October 1949. Also, it is the sixth in a series of reports prepared under a cooperative agreement between the Bureau of Mines and the American Association of Cost Engineers. The agreement provides for the publication of an annual cost bibliography with the work load involved in the preparation shared equally. The abstracted articles, concerned with all facers of cost engineering in the field of chemical and petroleum. plants and related subjects, are from the following sources:

Jan 1, 1965

By Sidney Katell

This report covers the period January 1964 through December 1964; it is a continuation of the series that began with the publication of Information Circular 7516 in October 1949. Also, it is the sixth in a series of reports prepared under a cooperative agreement between the Bureau of Mines and the American Association of Cost Engineers. The agreement provides for the publication of an annual cost bibliography with the work load involved in the preparation shared equally. The abstracted articles, concerned with all facers of cost engineering in the field of chemical and petroleum. plants and related subjects, are from the following sources: 1. American Association of Cost Engineers Bulletin. 2. Bureau of Mines Information Circulars. 3. Bureau of Mines Reports of Investigations. 4. Chemical Engineering. 5. Chemical Engineering Progress,

Jan 1, 1965

By C. J. Wilhelm

The disposal of brines produced with crude petroleum and natural gas has been a long-continuing problem to oil and gas operators as well as to farmers and stock-raisers in the vicinity of producing fields. .An impartial appraisal of conditions pertaining to the problem of brine disposal lead to the conclusion that study of the technical considerations, with proper weight given to the economic and social factors, is the most desirable approach to this problem . Brine disposal is a problem of such magnitude 1n certain areas in the State of Kansas that in August 1934 a cooperative agreement w s made between the Kansas State Board of Health and the U. S. Bureau of Mines for a cooperative technical study of methods of brine disposal.

Jan 1, 1935

By C. J. Wilhelm

The disposal of brines produced with crude petroleum and natural gas has been a long-continuing problem to oil and gas operators as well as to farmers and stock-raisers in the vicinity of producing fields. An impartial appraisal of conditions pertaining to the problem of brine disposal leads to the conclusion that study of the technical consideration, with proper weight given to the economic and social factors, is the most desirable approach to this problem. Brine disposal is a problem of such magnitude in certain areas in the State of Kansas that in August 1934 a cooperative agreement was made between the Kansas State Board of Health and the U. S. Bureau of Mines for a cooperative technical study of methods of brine disposal.

Jan 1, 1935

By J. H. East, R. S. Sanford, W. M. Traver, W. S. Wright

"INTRODUCTION This report describes the results obtained from a diamond-drill exploration project performed by the Bureau of Mines on the nickel deposits of the Yakobi Island, Alaska. The Federal Geological Survey 6/ completed a detailed geologic study and mapped the area during the summer of 1940, and a Bureau of Mines examining engineer 7/ made a preliminary examination of the deposits in June 1941, at which time core drilling was suggested as the logical means of determining the extent and grade of the deposits. Equipment and supplies were unloaded on the beach at Yakobi Island on October 21, 1941. The drills were moved to Bohemia Basin, where actual drilling operations wore begun under the direction of a Bureau of Mines engineer 8/ on November 7, 1941. Two core-drill holes were completed on December 7, 1941. Upon the request of the drilling contractor, operations were recessed owing to severe winter conditions. Work on the project was resumed April 27, 1942, under the direction of another Bureau of Mines engineer 9/ and was completed August 15, 1942. During the 1942 season, 13 core-drill holes were completed, and 10 surface pits and a tunnel were sampled. A total of 5, 191 feet of core-drill hole was drilled in 15 holes during the entire project. The results of drilling and sampling form the basis of this report."

Jan 1, 1948

By Claud Johnson, Kristine M. Krajnak

Vibration transmitted to the upper limb by the chronic use of hand tools can result in cold-induced vasospasms finger blanching and cyanosis, similar to that seen with Raynaud’s phenomenon (4). These vasospasms, commonly referred to as vibration white finger (VWF), are in part the result of an increased sensitivity of peripheral arteries to the vasoconstricting effects of norepinephrine (e.g., (1-3)). However, alterations in vasodilating factors could also contribute to vasospasms. The goal of these studies was to determine if exposure to a single bout of vibration alters concentrations of the vasodilator, nitric oxide (NO), in a rat tail model of vibration. To determine if vibration exposure alters NO, we exposed animals to a single bout of vibration and measured concentrations of the synthetic enzymes, nitric oxide synthetase (NOS)-1 and NOS-3 in the ventral tail artery. We also directly assessed arterial concentrations of NO using a nitrate/nitrite assay. Methods General apparatus. Animals were placed in Broome-style restrainers, and their tail was secured to a vibrating or stable platform. Rats were exposed to a single 4 h bout of tail vibration (125 Hz, acceleration of 49 m/sec2 r.m.s.) or restraint control. Animals were euthanized with an overdose of pentobarbital (100 mg/kg) and the ventral tail artery was dissected and frozen. Experiment 1: Male Sprague Dawley rats (6 weeks old, n = 32) were used for all exposures. All animals were maintained in AAALAC accredited facilities, and all procedures were approved by the NIOSH Animal Care and Use Committee, and were in compliance with the CDC Regulations for the Care and Use of Laboratory Animals. Animals were euthanized 1 or 24 h after the completion of the exposure. Western analyses were performed on total proteins (80 µg/lane) isolated from the C16-18 artery segments. Band densities were detected by chemiluminescence and quantified using Scion Image, and analyzed using 2-way ANOVAs. Experiment 2. Nitrate/nitrite concentrations.. Male Sprague Dawley rats (n = 24, 6 weeks of age) were maintained and exposed as described above. All animals were euthanized 24 h after the exposure and the ventral artery was collected. Nitrate/nitrite concentrations were measured in ventral artery tissue homogenates using the nitrate/nitrite colormetric Assay Kit (Caymen). Results Analyses of band densities revealed that there was an effect of time (F(1, 17) = 6.03, p < 0.03) on NOS-1 protein in arteries exposed to vibration, with NOS levels being lower in arteries collected 24 h after the exposure than arteries collected 1 h after the exposure. Although NOS-1 proteins concentrations were slightly lower in control arteries collected 24 h after an exposure than arteries collected 1 h after exposure, post-hoc contrasts indicated they were not significantly different than 1 h controls. In contrast, NOS-1 band densities from arteries collected 24 h after the exposure were lower than those collected 1 h after the exposure (p < 0.01; Figure 1). NOS-3

Jan 6, 2006

By R. Michael Digman

Few efforts have been undertaken to date to assess the quality of mandated coal mine health and safety training for new miners and for experienced miners. This study was concerned with the quality and effectiveness of existing classroom health and safety training programs. The study involved field data collection through pre- and posttesting of trainees, audio-taping class sessions, and administering short feedback forms with trainers and trainees at 14 sites in West Virginia, Maryland, Kentucky, and Pennsylvania. Results indicate that goals, methods, materials, and outcomes of existing training programs vary widely among trainers and sites. The report provides less by way of solution to problems, than it highlights the breadth of issues that relate to the question of training effectiveness and quality. The report concludes that additional work by industry, labor, government, and academia is necessary in order to improve health and safety training programs. Recommended steps are: (a) to develop performance standards and measurable criteria in each of the types of mandated training, (b) to develop better training of trainers, (c) to develop expanded training support services. and (d) to undertake further research and development in health and safety training in the mining industry

Jan 1, 1982

By G. L. Oldright

"The various districts in the United States where complex lead-zinc ores occur are too well known to require description, there being hardly a mining State with any large amount of ores of either metal that is free from this problem. This paper briefly presents developments in the volatilization process, as applied to the treatment of such ores, since the data in Bureau of Mines Bulletin 211** were published. In that bulletin, among the many types of ore treated, examples are given of the treatment of lead-zinc ores by the chloride volatilization process for the separation of lead. An outline of the general process, with views of the rotary kiln, ore feeder, firing system (these three features resemble closely those of cement-kiln practice), dust chambers, and a Cottrell precipitator to remove the fume from the gas, are also shown in that bulletin, to which the reader is referred for the results obtained, and for practical details of operation. The small initial cost of a volatilization plant, and its adaptability for use in isolated districts were emphasized.In general, it was found that when an intensely oxidizing atmosphere was maintained in the furnace, a good lead-zinc separation could be made. Therefore, a heavy sulphide ore would have to be preroasted, and enough air would have to be admitted to obtain complete combustion of whatever fuel might be used.The work done by private companies and the bureau since the data for Bulletin 211 were obtained, indicates that the ores most immediately amenable to treatment by volatilization are of two types. The first is an oxidzed lead. silrer ore whose variable lime content makes it impractical to chloridize the ore for acidulated brine leaching, and whose base metal content makes treatment by cyanidattion unfeasible, The second type is the lead-zinc ore mentioned above, and is the one on which data are available for publication at present. This article Chows what ores of this latter type are amenable to treatment by volatilization, by giving briefly some of the more important physical and chemical properties an ore should preferably possess. Several examples are given from both laboratory experimental work, and from practice in the field, showing various phases of the volatilization process."

Nov 1, 1923

In 2006, a total of 7,178 sand and gravel mining operations reported employment to the Mine Safety and Health Administration (MSHA).1 ? Sand and gravel mines were the largest mining sector, comprising 48.2% of all mining operations. ? Sand and gravel mines were found throughout all 50 states and Puerto Rico.

Sep 1, 2008

By Joseph J. Wallace

1. The investigation shows that there are 2 coal beds of major importance in Letcher County from the standpoint of present production - Upper Elkhorn No, 3 and Fire Clay - and 5 beds of minor importance - Whitesburg, Flag, Haddix, Elkhorn Leader, and Amburgy, The Upper Elkhorn No. 3 and Fire Clay beds contain the largest remaining known reserves. 2. Known measured and indicated reserves in all beds, based on a minimum thickness of 14 inches and on 1,600 tons per acre-foot of coal in place, are estimated at 1,353 million short tons as of January 1, 1952. Of this total, 1,056 million short tons ere in beds 28 inches and more thick. Areas in each bed were omitted from the estimate because available data relative to the bad characteristics are too meager to make an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.

Jan 1, 1953

By J. L. Eakin, J. P. Powell

"The increased costs of exploration and drilling of new oil fields and the continued success of water flooding in nearly depleted oil fields have created a demand for information on the results obtained from individual projects. The Bureau of Mines has published several reports concerning water-flood activity in the Midcontinent area and at the request of the industry has continued to collect and disseminate this information. This report was written in response to these requests. It describes in detail the water-flooding projects in Anderson, Franklin, Linn, and Miami Counties, Kans., and includes methods of water treating and the results obtained. The production histories of each county and many water-flood projects are shown graphically from the date of the first development. Maps of most of the major projects, showing their status as of January 1, 1953 are presented also.The practice of injecting water to stimulate oil production was legalized in Kansas in 1935, and the first water-flooding project authorized in this four-county area was initiated by the Texas Co. in December 1935 in Linn County. Forty-nine projects2/ initiated in the area to January 1953 are estimated to have recovered approximately 10 million barrels of oil that would not have been produced by methods used previously. About 7,900 productive acres had been, or are, flooded by these projects, and approximately 136 million barrels of water had been injected.These four counties in the eastern Kansas shallow production area3/ were an important factor in the early history of the Kansas oil and gas industry. This position has been maintained from the very beginning through the early period of vacuum and air injection and into the era of water flooding. The location of the area and the relative position of the four counties and water-flooding areas in each are shown in figure 1.The first drilling for oil in this area in 1860 resulted from investigations of the existence, and use by the Indians, of so-called tar or oil springs. The first wells drilled were nonproductive, and the impending Civil War caused the search for oil to be discontinued. In 1884 a few shallow oil wells were drilled near Paola, and completion of several gas wells near that city led to subsequent drilling of an oil well, which was completed in June 1885, having an initial flow of 10 barrels of oil daily.In 1904 the original Paola gas field became a good oil-producing field. In 1905 the Rantoul field in Franklin and Miami Counties was opened; and drilling activity spread throughout the adjoining area, resulting in development of several shallow oil pools in Linn and Anderson Counties. The first ""shoestring"" pool in eastern Kansas to produce oil was probably the Paola or Pressonville shoestring, which was discovered in 1917. The rate of oil production from the area declined until 1919, when the Centerville shoestring pool was discovered. Discovery of the Colony gas field in 1921 was followed within a few months by drilling of the Garnett and Garnett and bush City shoestring pools. The Schermerhorn pool (now part of the Centerville field) s discovered in 1927, and the Kincaid shoestring pool was first drilled in 1931. The oil-production histories of the individual counties are discussed separately."

Jun 1, 1953

By R. D. Eash

The purpose of this research contract was to develop and test a Saran latex modified portland cement concrete lagging to be used as a replacement for wood lagging. The scope of work performed was divided into four phases: Phase I - Engineering Criteria; Phase-! I1 - Design Study; Phase III - Fabrication of Lagging; and Phase IV - Prototype Demonstration Project. Each phase of work was completed and is described in detail in this report. The prototype latex modified concrete lagging developed in this program weighed 52 pounds. When tested in flexure, it supported center point loading of 4500 pounds and under 1/4 point loading it supported loadings of 7000 pounds. Deflections at maximum loading ranged from 1/2 to 1 inch. Maximum deflections exceed 2 inches. The lagging does not exhibit catastrophic failure. Two hundred and twenty of the LMC lagging were produced and shipped to the Bunker Hill Company in Kellogg, Idaho for installation in their mine at the 17 level. The lagging are performing satisfactory after 22 months exposure in the mine.

Jan 1, 1980

By Douglas Ketcham, Thomas Jetzer

While the neurological and vascular aspects of Hand-Arm Vibration Syndrome (HAVS) has been generally accepted as a medical condition, the medical criteria and the clinical findings used to establish the diagnosis has been more difficult to bring to consensus. The criteria was first quantified by the Taylor-Palmear scale.1 This criteria was subsequently modified in 1986 at the 1st Stockholm Workshop2,3 to included more acceptance for the neurological effects that characterized the predominate findings in some workers. The relationship between hand-arm vibration and Carpal Tunnel Syndrome was defined in NIOSH 97-1414. While the aforementioned documents have defined the clinical entities associated with hand-arm vibration exposure, agreement on the clinical findings and test to confirm the diagnosis has be been more difficult to bring to consensus. Clinicians assessing HAVS has relied on a number of varied neurological and vascular tests. The neurological testing has focused on assessing damage to the sensory capability of the fingers for the neurological component including tests to measuring ability to sense vibration, cold or other end point finger sensor functions. However, the vascular testing has been traditionally focused on the ability to either measure vascular function or to reproduce the vascular blanching that occurs in HAVS with cold water provocation. Recent assessment of this testing in the United Kingdom Coal Miner’s study has questioned the value of this testing especially in reviews by McGeoch.5 In an attempt to provide some type of definitive testing to substantiate vascular damage from hand-arm vibration exposure, angiography is an alternative or adjunct to cold water provocation testing. The standards that have been established to predict the level, type and incidence of HAVS have been based on clinical studies and reports that have essentially been all male populations. However, the recent entry of women into more vibration intensive jobs has brought about the exposure of some women to high levels of vibration previously only previously experienced by men. However, there have been only few studies that look at HAVS in women6. Although exposed the same vibration levels, it has not been clear that the latency and type of pathology of HAVS in women will be the same as for men. The purpose of this study is to look at recent case studies of men and women exposed to jobs with high levels of hand-arm vibration with extensive clinical testing for both the neurological and vascular components of HAVS as well as other associated upper extremity conditions such as Carpal Tunnel Syndrome.

Jan 6, 2006

By E. J. Gleim

A study of the records on file in the Bureau of Mines reveals that moray fire in coal mines have been started by electrical equipment or circuits. There the fires were of undetermined origin, electricity often was Strongly suspected as the probable cause. While it is unfortunate that positive evidence as to the cause is so often lost in the general destruction resulting from fires, there are many lessons to be learned from fire s in which the origin was definitely established as electrical. For modern high-speed methods of producing coal, electrically operated machinery has become virtually indispensable underground. With increases in the amount of equipment it has not always been necessary to increase the number of circuits in the mine where direct current is mainly used, but it has been necessary to increase the carrying capacity of these circuits. For example, lends such as heavy-haulage units drawing 1,000 amperes or more have brought boat the introduction of 6/0 and "No. 9 section" trolley wires. This has not made the task of fire prevention any easier, for it has meant that circuit breakers s must be set so high that partial short circuits fail to open them, therefore an arc of considerable proportions can be maintained without causing the, beaker to open. Thus, if as fall of roof brought a trolley wire down against a loaded car of coal, an arc might be struck that would ignite they cowl without opening the circuit breaker.

Jan 1, 1937

These proceedings consist of an introduction, nine descriptive papers, and a summary. The first paper is an overview of the respirable dust research program, the second paper describes the Mining Enforcement and Safety Administration&apos;s proposed changes in the respirable dust enforcement program, and the third paper describes respirable dust measurement. The remaining papers, by Bureau and contractor personnel, describes methods of reducing the amount of respirable dust to which coal miners are exposed. Of the six methods of reducing exposure to respirable dust described, two are methods of preventing or reducing the amount of respirable dust raised during mining operations, two are methods of collecting or removing dust after it has been released into the mine atmosphere, 2nd two describe methods that are combinations of prevention and collecting .

Jan 1, 1977

By N. Kumar Kittusamy

The purpose of this study was to assess the adequacy of the cab design and to determine the percentage of musculoskeletal symptoms among operators of mobile equipment used in mining and construction. A questionnaire was designed to assess demographics, work information, job history, and musculoskeletal symptoms in operators of heavy mobile equipment. Information concerning equipment included design of the seat/chair, levers, pedals, bothersome vibration, quality of ingress/egress from the equipment, proper preventative maintenance and repairs, and age of the equipment. The body regions that were evaluated included the neck, middle/upper back, low-back, shoulder/upper-arm, elbow/forearm, wrist/hand, hip, knee, and ankle/foot. Five hundred and eighty six operators completed the questionnaire. The results indicate that these workers are at risk for developing musculoskeletal disorders, and the need to quantify risk factors (i.e., whole-body vibration and static sitting postures).

Jan 6, 2006

By Luis v. Coppa

Since its inception in 1910, the Bureau of Mines has been the principal Federal agency involved in ore reserve estimations, using such traditional methods as polygons of influence and variations of inverse distance weighting While adequate for estimating the average are grades in a mining block or section, these methods do mot, however, provide a consistent way of quantifying the reliability of the estimates. This report describes a technique for enhancing ore reserve estimations using geostatistics, the methodology of which combines the spatial and random aspects of geologic phenomena into a formal theoretical framework for deriving the estimation variance of ore reserves. Correctly used, geostatistics enables confidence intervals to be placed around ore reserve estimates calculated from drill hole data. A geostatistical software system was obtained -From the U.S. Geological Survey and installed, aster slight modifications, on the Bureau&apos;s Wang computer. System testing and validation was conducted using a simple cast-book-type example. This was then followed by variogram analysis, point kriging and block kriging of data from a previously worked section of a uranium mine.

Jan 1, 1984

By William W. Aljoe

This report summarizes the Bureau of Mines noise-control research program from 1972 to 1982. Each segment of the mining industry--under- ground coal, underground hardrock, surface mining, and processing plants--has different noise-control problems because of vast differences in working procedures, equipment, and workplace design. The Bureau has identified the most serious noise problems in each segment and has developed strategies for attacking these problems. This publication points out the need for noise control in the mining industry, discusses Federal regulations governing worker exposure to noise, and describes the Bureau&apos;s overall approach to mining noise- control research. It traces the history of noise overexposure in each segment of the mining industry and discusses the major noise sources. It provides detailed information on noise-control research efforts in the Bureau&apos;s major areas of emphasis, including the results of these efforts. Finally, the report discusses the Bureau&apos;s future role in research on mining noise control, emphasizing the need to expend more effort on long term in-house investigations into the noise problems that have been identified in past programs as the most serious ones.

Jan 1, 1985