Search Documents

By J. L. Holman

The Federal Bureau of Mines has conducted research to delineate factors affecting relative fabricability of electrowon and electrorefined copper. The Bureau's Rolla Metallurgy Research Center coordinated and participated in a statistical round-robin chemical analysis and performed impact tests on lead-doped copper specimens. In a series of round-robin analyses, cathode, bar, or rod from a domestic lot of electrorefined copper and electrowon copper from a domestic and a Peruvian source were analyzed for Pb, Fe, Bi, Se, Ag, O, S, Sb, and seven other elements. The electrowon cathode from both sources surpassed requirements for electrolytic cathode, although lead in the Peruvian lot exceeded specification for oxygen-free electronic grade. The least interlaboratory agreement was for oxygen analysis, Copper specimens, doped with up to ~300 ppm Pb and consisting of as-cast material (fine-grained or coarse-grained) and hot-rolled material, were impact-tested at temperatures to 871° C (1,600° F). Impact energy of fine-grained material dropped 26 pct with increased Pb up to 20 ppm and more gradually thereafter. Coarse-grained specimens fractured at lower energy with little dependence on lead. Hot rolling raised impact energy substantially. Grain structure is evidently as significant as lead in influencing workability. Some discussion is given of possible effects of oxygen, sulfur, and porosity.

Jan 1, 1978

By D. K. Denton, J. M. Girard, D. F. Scott, T. J. Williams

Personnel from the Spokane Research Laboratory, National Institute for Occupational Safety and Health, examined an underground pillar at the Homestake Mine, Lead, SD. Investigations involved strain relief and seismic tomography studies in the mine, and ultrasonic velocity measurements on pillar core in the laboratory. Measured octahedral normal stress was 37 MPa (5,366 psi); seismic P-wave velocities averaged 5.2 km/s (17,060 ft/s); and ultrasonic velocities at a pressure of 39.6 MPa (5,750 psi) averaged 6.3 km/s (20,669 ft/s). The difference between in-mine and laboratory velocities is attributed to the attenuation of seismic energy by mine fractures larger and more numerous than those in the samples of core measured in the laboratory. Using these results, researchers hypothesize that pillar rocks have the ability to withstand stress an order of magnitude greater than they currently sustain.

By Siavoljub D. Maksimovic

The Bureau of Mines, through a cooperative agreement with Duquesne Light Co. of Pennsylvania, field tested a method of using pneumatic stowing of crushed limestone to construct seals in long-abandoned mine openings that were part of an active mine closed shortly before sealing. A total of 13 openings at 11 sites were backfilled. In pneumatic stowing, material is conveyed through a pipeline and into the mine opening under low air pressure. The stowing equipment consists of a power sup-ply, a blower, a feeder to inject material into the pipeline, and a nozzle for directing the placement. Material is ejected from the nozzle at high velocity, creating a high-compaction fill upon impact. The fill material used was well-graded limestone aggregate up to 1-1/2 inches in diameter, with sufficient fines. This fill was modified at five locations by the addition of portland cement, expansive cement, and/or bentonite. The pneumatic stowing method is safer and faster than conventional methods, is cost competitive, and eliminates or reduces the exposure of workers to possible hazards since the nozzle can be kept outside the mine opening. The equipment is mobile, but some modifications in the technique would improve performance. The technique was used at remote locations where other methods could not be used without disturbing the environment.

Jan 1, 1982

By C. W. Davis

During the fiscal year 1935-36, the Ore-Testing Section has been active in carrying out a program designed to attain the objectives that have been set up for it. For the Purpose of standardizing important testing methods, an attempt has been made to develop a rationalized scheme for ore testing, starting with preliminary investigations to determine the physical and chemical properties of the ore, following this with a logical selection and trial of processing tests to find out how the ore may be most effectively treated, and concluding with a discussion of what interpretation may be placed on the results in terms of plant design and operation. A selection of Procedures that appear well-suited to the ore-dressing problems under investigation is included in the following paper of this report so that other experimenters may be enabled to verify our findings and to offer criticisms and suggestions for improving our practice. A tentative scheme for the evaluation of flotation reagents is being investigated, and some progress has been made in a study to determine the significance of small-scale testing. These projects have required 899 analyses. Papers on these and others on ore testing, such as testing for amalgamation and for cyanidation, will be included in future annual reports.

Jan 1, 1937

By W. K. Connor, O&apos

The U.S. Bureau of Mines investigated the Sheep Creek prospect in the north-central Alaska Range to evaluate the Pb, Zn, Ag, and Sn resources. The studies included field investigations, mineralogical characterization, and concentration tests. Mineralization at Sheep Creek consists of disseminated, banded, and massive pyrite, sphalerite, and galena. Tin occurs as grains of cassiterite (Sn02) in the quartz-mica matrix and within pyrite and sphalerite grains, and Ag occurs in solid solution within the galena. Three bulk surface samples and two sets of core samples were collected at the Sheep Creek prospect for this study. Gravity concentration yielded products with up to 30 pct Sn, and the best result was a product that recovered 52 pct of the Sn at a grade of 22 pct Sn. Bulk sulfide flotation yielded products that recovered up to 89 pct of the Zn, 73 pct of the Pb, and 75 pct of the Ag, but grades were relatively low; selective flotation would significantly increase the grades.

Jan 1, 1989

By Annie G. Smelley

As part of its program to develop technology that will encourage maximum utilization of the Nation's mineral resources, the Bureau of Mines conducted research on debrining potash-clay waste slurries by means of flocculation with a high-molecular-weight polymer and subsequent solid-liquid separation on a rotating trommel screen. In laboratory batch tests, potash-clay waste slurries were consolidated from initial clay contents of 8 pct to final contents of 30 pct with a polymer dosage of 1.2 Ib/ton of dry clay waste. Small-scale continuous tests yielded debrined products containing 20 pct solids using a polymer dosage of 1 Ib/ton of dry clay solids.

Jan 1, 1983

To provide a flexible, low-maintenance, low-cost continuous mine air monitoring system as an alternative to conventional fixed-point, electronic monitoring systems. Background Continuous monitoring of mine air is highly desirable (and often required) not only to improve miner safety, but also to increase mine productivity. Continuous air monitoring systems can provide earl" warning of developing fires, excessive methane accumulation, reduced oxygen levels, and other developing problems in remote, inaccessible or sealed areas, and in active workings. Fixed-point, electronic systems require one Sensor for every gas to be measured at every defined monitoring location. As the number of monitoring locations increases, so does the cost, along with increases in the time required for routine maintenance and calibration of the sensor System cost also increases when monitoring locations are identified for mine areas requiring permissible electrical equipment.

Jan 1, 1988

By John H. Johnson

Diesel tailpipe CO, C02, NO, and N02 concentrations by the Emissions Measurement Apparatus (EMA) were found to compare satisfactorily with simultaneous concentrations by instruments in the MSHA engine certification laboratory in Bruceton, Pa. The EMA was then applied to the measurement of LHD vehicle diesel tailpipe gases and smoke opacity in the White Pine and Brushy Creek Mines. A general experimental approach was developed by which instruments could be compared for the measurement of diesel exhaust pollutant concentrations in the 1/2 to 5TLV range. The concentrations are changed by varying engine speed, dynamometer load, and the portion of the exhaust which enters the dilution tunnel. Dräger detector tube diluted exhaust CO, CO2, NO, and NO2 measurements were compared with simultaneously taken portable instrument measurements. Diesel exhaust interference inaccuracies were separated from inaccuracies due to detector tube calibration by comparing the instrument readings with both actual detector tube readings and detector tube readings corrected by recalibration of the detector tubes alongside NBS traceable calibration gases. The detector tubes' accuracy was found to be only slightly affected by diesel exhaust interferences and it was concluded that most measure within certification limits established by the National Institute for Occupational Safety and Health. The effects of 2 exhaust system configurations on the pollutant concentrations in a dead-end heading were studied. Both of the configurations exhausted the gases near the roof, directing them toward the crosscut, and both improved the stratification of the air in the heading, due to the bouyancy of the hot exhaust gases. One of the configurations was a pair of Fume Diluters which diluted the exhaust with air by a 10:1 ratio, and the second system was simply a pair of exhaust pipes, bent to direct the exhaust similarly to the fume dilutors. By redirecting the exhaust, the concentration of C02 measured on the LHD vehicle was reduced by as much as 507, in dead-end headings up to 200 ft long. The Fume Diluters showed no improvement over the simple redesign of the exhaust system.

Jan 1, 1980

By Bill Linville

Producing oil, gas, and coal in sufficient amounts to satisfy U.S. demands for fuels, electrical power, and chemicals promises to be one of the country's major challenges during the 1970's. Adding significantly to this challenge is the urgent task of satisfying soaring fuel and power demands without destroying the natural environment or jeopardizing long-range requirements for resources. The Bureau of Mines, U.S. Department of the Interior, is engaged in a comprehensive program of research to help industry meet this challenge. This report reviews the aims of the research program and accomplishments in 1970; the first 11 sections cover coal programs, nine sect ions are then devoted to petroleum, and the concluding five sections deal with oil shale research. Figure 1 shows the nationwide distribution of Bureau of Mines energy research installations; Full addresses are given in appendix A. Many of the publications resulting from the Bureau?s energy research efforts are discussed throughout the report; others are listed in appendix B.

Jan 1, 1971

By C. M. Harrer

This paper describes the location, features, qualities, extent, and potential of iron occurrences and some associative resources -limestone and dolomite, coal, petroleum and natural gas, power, and water - in New Mexico. Reconnaissance investigations were made of 118 iron occurrences to deter-mine their extent, attitude, and potential; character samples were analyzed to determine their quality and impurities; and pioneer metallurgical investigations were made on character samples to present their metallurgical problems. Some factors influencing past and potential iron markets are discussed. The most abundant iron minerals are magnetite and hematite. The higher grade deposits are extensive contact-metamorphic and pyrometasomatic replacements in calcareous Paleozoic rocks associated with intrusives. Low-grade deposits of considerable potential are the extensive Cambrian oolitic hematites of sedimentary origin and the Precambrian magnetite-hematite taconite iron formation. Iron occurs also as extensive colluvial and alluvial concentrations. A wide variety of accessory elements are indicated and these pose metallurgical and economic problems.

Jan 1, 1963

By C. M. Harrer

This paper describes the location, features, qualities, extent, and potential of iron occurrences and some associative resources - limestone and dolomite, coal, petroleum and natural gas, power, and water - in New Mexico. Reconnaissance investigations were made of 118 iron occurrences to determine their extent, attitude, and potential; character samples were analyzed to determine their quality and impurities; and pioneer metallurgical investigations were made on character samples to present their metallurgical problems. Some factors influencing past and potential iron markets are discussed. The most abundant iron minerals are magnetite and hematite, The higher grade deposits are extensive contact-metamorphic and pyrometasomatic replacements in calcareous Paleozoic rocks associated with intrusives. Low-grade deposits of considerable potential are the extensive Cambrian oolitic hematites of sedimentary origin and the Precambrian magnetite-hematite taconite iron formation. Iron occurs also as extensive colluvial and alluvial concentrations. A wide variety of accessory elements are indicated and these pose metallurgical and economic problems.

Jan 1, 1963

On July 1, 1969, the Explosives Research Center merged with the Health and Safety Research and Testing Center to form the Safety Research Center, with facilities at Pittsburgh and Bruceton, Pa. Subsequently, passage in December of the Federal Coal Mine Health and Safety Act of 1969 (Public Law 91-173) had a major influence on the activities of the new center. These activities were conducted under two main programs, Coal Mine Safety Research and Explosives Research. The Coal Mine Safety Research program was concerned primarily with two categories of hazards: health-related hazards associated with the mine environment, due to such factors as respirable dust, toxic gases and vapors, and excessive noise; and accidents due to mine fires, explosions, and roof falls.

Jan 1, 1972

By J. T. McLendon

As part of its research project in developing improved refractory materials for metallurgical applications, the Federal Bureau of Mines obtained hot modulus of rupture data at 1,500°,1,550°, and 1,600° C on samples of 13 refractory periclase materials produced from seawater, lake brines, and natural magnesite. The periclase samples also were characterized to establish chemical and mineralogical composition and microstructure. The results indicated that a high MgO content does not necessarily assure good hot strength and that an optimum and varying CaO-Si02 ratio exists for each individual periclase sample.

Jan 1, 1979

By Chas. G. Maier

The absence of plants on the Pacific coast for the reduction of iron ores usually is attributed to the fuel situation there. Thus, the bulletin of the. State Division of Mines for 1933, entitled "California Mineral Production," says: "There are considerable deposits of iron ore known in California, notably in Shasta, Mad era, Placer, Riverside, San Bernardino, and Los Angeles Counties, but production has so far been limited for lack of an economic supply of coking coal." It has been estimated that the six major steel plants of the Pacific coast have an annual ingot capacity of 600,000 tons. The present need for tin plate averages 300,000 tons yearly for California alone, of which some 12 percent is manufactured locally. If the consump¬tion of other iron and steel products in 1929 may be taken as an approximate, estimate of the normal requirement for such products, it may be estimated further that, 65,000 to 75,000 tons each of cast-iron pipe and steel reinforcing bars and 300,000 to 400,000 tons of structural shapes and plates will be required annually in California.

Jan 1, 1936

[Determine how subsidence resulting from underground coal mining affects surface structures, and evaluate the usefulness s of the tiltmeter for monitoring foundation movement. Approach The Bureau of Mines is studying foundation response to mine subsidence in order to determine how subsidence-induced ground movements affect foundations in place directly above the mint. These investigations are essential if economic mitigation and repair techniques are to be made. In addition, commercially available tiltmeter are being evaluated (or use as a cost-effective monitoring technique. To study foundation response and to evaluate the tiltmeter system, full-scale model foundations were constructed, instrumented, and monitored for three years. Vertical and horizontal displacements, tilt magnitudes and directions, and observed damages were recorded. Displacements were compared with measured lilt to determine if the tiltmeter was tracking foundation response to subsidence, The Bureau developed a computer software package to aid in the reduction and analysis of the tiltmeter data.]

Jan 1, 1988

During the second quarter of 1983, the economic recovery showed further strength abetted by the performances of consumer spending, residential investment, and the slowing down of inventory reductions. Real gross national product (GNP) increased from the first to second quarter at an annual rate of 9.2 percent, compared with 2.6 percent from the fourth quarter of 1982 to the first quarter of 1983 and an overall 1.9- percent decrease in 1982. Total industrial production increased 1.8 percent in July, and productivity as measured by output per man-hour increased 1.3 percent between 1982 and the first quarter of 1983 (table 1). Especially noteworthy .was the performance of real consumer durable goods expenditures, which increased at an annual rate of 32.0 percent from the first to the second quarter (about half of the increase consisted of automobile sales) and real consumer spending, which increased between these periods at an annual rate of 9.7 percent. Residential investment increased at an annual rate of 76.1 percent between the first and the second quarters,1/ and private housing starts by about 38,000 units in both March and May.

Jan 1, 1983

By Victor R. Spironello

The Bureau of Mines has studied slags associated with ferrous melting, to evaluate substitutes for the auxiliary flux mineral, fluorspar. A waste material recovered from alumina reduction cells, "used potlining," was tested in an 18-in-ID basic-lined cupola and in a 1/4-ton, pilot-scale, basic oxygen furnace (BOF). One potlining fraction, No. 1 cut, is a carbonaceous (graphitic) material and represents the bulk of the entire cell lining. The other fraction, No. 2 cut, is a refractory backup. These materials contain significant quantities of fluorine and other elements fn various compounds. The potlining fractions were blended in ratios believed representative of available materials. Both lump and pelletized forms provided extremely fluid slag. No adverse effects were found on furnace performance, chemistry or strength of the metals produced, or the environment. Fluorine recovery in the slag and fluorine losses to the scrubber water and solids were about the same as when fluorspar was used. There was apparently no lining loss from the cupola, but there was lining attack in the BOF. Since the fluidizing ability of potlining is due in part to sodium and other elements such as aluminum and silicon, less fluorine is needed in the slags when potlining is used.

Jan 1, 1983

The strippable reserves of bituminous coal and lignite in the United States were calculated in accordance with the prevailing conditions of seam thickness and depth of overburden in each of the several coal-producing areas of the Nation. Within defined limits of seam thickness and depth of overburden, it is estimated that there was a remaining strippable resource of 118 billion tons of raw bituminous coal and lignite as of January 1, 1968. Because of topography, natural and manmade features, and other limitations, only 45 billion tons of the resource are strippable reserves. Of this, 32 billion tons is considered low-sulfur (less than 1 percent), 4 billion tons is medium-sulfur (1 to 2 percent), and 9 billion tons is high-sulfur (over 2 percent) coal. Owing to a cleaning loss affecting that portion of strip coal that is mechanically cleaned, the 45 billion tons of strippable reserves are reduced to 39.6 billion tons of marketable coal. A brief discussion is given for each coal-producing State, summarizing past and present production, historical background, and outlook. Appendix A contains reserve data by State, county, seam, and sulfur content. Appendix B contains the general information and requirements necessary to comply with the current strip mining laws covering 20 States.

Jan 1, 1971

By Rose L. Ballard

This chapter summarizes data on crude nonfuel mineral production for the United States, its island possessions, and the Commonwealth of Puerto Rico. Included also are the tables that show the principal nonfuel mineral commodities exported from and imported into the United States and that compare world and U.S. mineral production. The detailed data from which these tables were derived are contained in the individual commodity chapters of volume I and in the State chapters of volume II of this edition of the Minerals Yearbook. Although crude mineral production may be measured at any of several stages of extraction and processing, the stage of measurement used in this chapter is what is ordinarily termed "mine output." It usually refers to minerals or ores in the form in which they are first extracted from the ground, but customarily includes the output from auxiliary processing at or near the mines.

Jan 1, 1983

By Virgil A. Marple

The objective of this contract was to investigate time-integrated and real-time methods for determining the diesel exhaust particulate concentration in underground mines, in particular, coal mines. The microorifice uniform deposit impactor (MOUDI) is recommended for obtaining the time-integrated measurement of the size distribution. The mass concentration of diesel exhaust particles can be obtained from the particle size distribution of mine aerosols. On a mass basis, diesel exhaust particles are primarily in the submicrometer size range while coal dust particles are larger. Size distribution measurements made in the laboratory and in three underground coal mines exhibited two distinct modes with the diesel exhaust particles in the smaller particle mode and the coal particles in the larger particle mode. The point of separation between the two modes occurred in the 0.7 to 1.0 pm size range. The separation was found to be independent of mass fraction of the diesel exhaust particles, particle concentration and sampling site. Methods recommended for further consideration as real-time monitors of diesel exhaust aerosols in mines are photometers and filter pressure drop techniques. A preclassifier would be required in both cases to separate the larger dust particles from the sample. The Metrex Mineral/Diesel Photometer should also be investigated further once the electronics problems are eliminated.

Jan 1, 1986