Search Documents

By Nick Lewis

Farce Mining of Texas is a surface coal mine located in Laredo, Texas. Farce mines and sells approximately 600,000 tons /year of bituminous coal. A map showing the location of Laredo is provided in Figure 1. As shown, Laredo is located on the border between the United States and Mexico. The mine property runs to the Rio Grande River, the border between the two countries. Farce pumps water from the Rio Grande for use in their coal preparation plant. Laredo’s climate is quite dry with annual rainfall averaging about 12” per year. Also, due to the southern location, Laredo is quite hot. It is common for the temperature to reach 100” F in March and maintain these temperatures through September.

Jan 1, 1994

By Timothy Stark

Blasters are usually strictly liable for injury or damage caused by flyrock (trespassory invasion) and blast-induced vibrations (non-trespassory invasion). The application of strict liability to non-trespassory invasions has resulted in significant litigation that has hampered the use of blasting and the blasting industry. Stark (2002) proposes that blasters should not be held strictly liable for non-trespassory invasions but should be liable only if their conduct is proven to be negligent. This change in legal standard was proposed because improvements in blasting technology over the last thirty years allow blasting to be conducted without substantial risk of harm to property and thus the amount of harm imposed by a blast can be related to the level of care exercised by the blaster. It is anticipated that a negligence standard will reduce the amount of litigation because a plaintiff will have a greater burden to overcome. To facilitate the acceptance of a negligence standard by a court of law, this paper summarizes the standard of care using the 1977 Surface Mining Control and Reclamation Act, extensive U.S. Bureau of Mines research, and current blasting techniques, such as blasting mats. It is important for the blasting industry to promulgate a standard of care so a judge can feel confident that blasting can be routinely and systematically controlled and if the legal standard is changed from strict liability to negligence a subsequent judge or jury will be able to evaluate the level of care exercised by the blaster. This paper also suggests that the industry and/or ISEE develop and disseminate a comprehensive standard of care that courts can use to further justify a change from strict liability to negligence and evaluate the standard of care.

Jan 1, 2003

By : D. Lawrence

Certain blasting applications are more prone to the generation of significant levels of nitrogen dioxide post blast fumes, more commonly referred to as after blast smoke, generally ranging in color from dark yellow to bright red. This paper reviews basic background chemistry defining the observed fumes and attempts to correlate geology, blast design, and explosive composition effects on the level of nitrogen dioxide that can be observed in various blasting conditions. Additionally, a test setting for evaluating the generation of post blast fumes is presented with pertinent test data detailing generic explosive formulation modifications which effect the overall level of post detonation generation of nitrogen dioxide.

Jan 1, 1996

By Paula Pereira

The better the capability of accurately predicting the results of any process the less laborious and costly is the optimization or improvement of that process. Rock blasting is a process that one intends to optimize for productivity and cost. Cast or throw blasting is a particular type of rock blasting which is widely used in surface coal mines, where draglines are used to remove the overburden from the top of the coal seam, in preparation for coal mining. Usually, the more rock that is thrown by the blast to the spoil side of the cut or pit, so that the dragline does not have to handle it, the more cost-effective is the cast blasting operation. As such, from an operating cost standpoint, it is crucial to better understand and predict the performance of cast blasting. The Distinct Motion Code or DMC is a Discrete Element Model which has been under development since 1987 and has been used to predict rock motion in several types of mining operations, particularly in surface coal and gold operations.

Jan 1, 2001

By Steve Dillingham

Blasting crews, explosive product drivers, drillers, blasters, supervisors, and salespeople all arrive daily at customer blast sites in vehicles of every type whether passenger cars, pickup trucks, or bulk trucks. The majority of these vehicles are company owned and re p re s e n t a substantial investment and risk for the company. That may explain why the costs resulting from blasting incidents is often surpassed by those involving motor vehicle accidents.

Jan 1, 2003

By Douglas A. Anderson

The simplest method used to predict ground vibration from blasting is scaled distance -the distance from a blast divided by the square root of the Pounds per delay. Pounds per delay is defined as the number of pounds of explosive detonated within an 8 millisecond (ms) interval. Based upon this definition, regression plots of peak particle velocity vs. scaled distance have been used to determine likely values of peak particle velocity.

Jan 1, 1989

By W B. Gregg

The rock blasting and mining industries use a system of detonators and explosives for mining operations. Many detonators use small metal bridgewires, which are heated by passing a current through the wire, heating and igniting the pyrotechnic powder in contact with the wire. Typical bridgewires require a current of at least 3 amps, applied for a few milliseconds, for an explosive output. The semiconductor bridge (SCB), in comparison, initiates an explosive in 0.01 to 0.1 of a millisecond.

Jan 1, 1994

By Ed Clah, Catherine Aimone-Martin

The vibration response of a 30 in. diameter high-pressure (845 psi) natural gas pipeline to 11 coal mine blasts was measured. The X-52 steel pipeline was buried 7 ft. below the ground surface. Ground and pipeline motions in terms of velocities were recorded on the pipeline, in the ground adjacent to the pipeline, and near the ground surface directly above the pipeline. These data were used to estimate the maximum stresses and strains in the pipeline occurring during the blasts. Pipeline standoff distances varied from 264 ft. to 3720 ft. Two blast hole layouts and timing schemes were used. One represented highly confined blasts to limit movement of the shot overburden that generated high ground motions at the pipeline. The second represented patterns that provided greater relief and lower the ground velocities at the pipeline.

Jan 1, 2003

By B Mohanty, Y C. Lizotte

Optimization of blast fragmentation in underground hardrock mining requires analysis of its effects on loading and haulage equipment, together with the downstream materials handling system, with the objective of minimizing total mine operating costs. A methodology is reported which has been developed to quantify the actual fragmentation and equipment performance in the field. This is data which has seldom been practicable to capture nor received serious attention in mines. Based upon the experience gained in underground studies, a prototype standard is proposed which aims to summarize the pertinent data, collection and analysis for fragmentation assessment. This relates to parameters of direct measure, such as mean size and distribution, as well as muckpile and work environment. The paper concludes by defining the impact of fragmentation on the loading and downstream handling system.

Jan 1, 1991

By Dong-Hyun Kim Kim, Tai-Ro Lee, Young-Hwa Seo

Overbreak occurred inevitably in a tunnel excavation, is the main factor for increasing cost and period in tunnel projects. Furthermore the damage to the remaining rock mass related to the overbreak can give rise to a serious safety problem in tunnels. As a rule of thumb, causes for the overbreak are inaccuracy in drilling, the wrong design of blasting and selection of explosives, and heterogeneity in rock mass. Specially, the geological features of the rock mass around the periphery of an excavation are very important factors, so a lot of research has been conducted to describe this phenomena. But the geological rockmass classification for the overbreak and the method for decreasing the overbreak have not been fully established. Besides, the technical improvement of the charge method is needed as explosives for the smooth blasting have not functioned efficiently. In this study, the working face around periphery of an excavation has been continuously sectionalized to 5~ 6 parts, and the new Blastability Index for the overbreak based on 6 factors of RMD(Rock Mass Description), UCS(Uniaxial Compressive Strength) JPS(Joint Plane Spacing), JPO(Joint Plane Orientation), JPA(Joint Plane Aperture) and FM(Filling Material) is proposed to classify sections of the working face. On the basis of this classification, the distance between contour holes and the charging density are determined to minimize the overbreak. For controlling the charging density and improving the function of explosives, the New Deck Charge(N.D.C) method utilizing the deck charge effect and detonation transmission in hole has been developed.

Jan 1, 2003

By Jack Elorenta

We often hear that, "Blasting was an art, but now blasting is now a science". 'Scientific' blasting implies that we have quantified and reproducible measurements of the feedstock and product of the blasting process. However, the industry's reluctance to adopt two key technologies, drill monitoring and optical size analyzers, sheds doubt on the claims of scientific blasting.

Jan 1, 2003

By Kai Nielsen

The paper presents the results of several industrial and laboratory blasting, crushing and grinding tests and experiments investigating how blasting can influence the subsequent crushing and grinding operations. The paper also describes how these results can be used in order to optimize the entire comminution process from solid ore to a semifinished or marketable product. Two cases are presented, one looking at the processing of fine grained taconite ore, and the other discussing the processing of raw milling product for cement burning.

Jan 1, 1998

By Bruce B. Redpath, Doug Crice, Rob Huggins

Over the last decade, instrumentation has been developed that allows the application of seismic reflection methods to groundwater and engineering problems. At the Geological Survey of Canada, we have been developing and testing shallow reflection techniques for mapping the bedrock topography and structure within the overburden. We have attempted to develop methods which can be implemented with a minimum investment in equipment and computing capabilities. The data are recorded on a l&channel engineering seismograph, using a single high-frequency geophone per channel, and a hammer or in-hole shotgun (“Buffalo gun”) as the seismic source. Processing and display of the data can be accomplished on an Apple II+ or IIe microcomputer and an Epson wide-track dot-matrix printer.

Jan 1, 1991

By David A. Bacca

Hydraulically powered submersible borehole dewatering pumps and emulsion/ANFO blends evolved at about the same time and for the same reasons. Mining operators needed safe, efficient dewatering systems and water resistant products.

Jan 1, 1994

By Wang Xuguang, Tian Ruigi, Xiong Shangbin, Xiong Daiyu

Combining action features of explosive shock with those of natural lignocellulosic biomass structure, we have successfully developed a new explosive shock dilatation and separation technique for pretreatment of natural lignocellulosic materials in the laboratory. Based on a brief introduction to the technical background and experimental procedure of this new method, some preliminary experimental results are given and discussed: the scanning electron microscope (SEM) qualitative observation results show that for treated natural lignocellulosic sample such as corn cob etc., their length of fibre bundle shortens, fibre bundle arrange disorders, biomass appearance and structure of samples largely change to be dilatation and loose state. The dilute acid hydrolysis quantitative measure results show that for treated samples, the overall yield of the reducing sugar largely increases, hydrolysis rate of corn cob sample is over 80%, rate and speed of hydrolysis are increased by times.

Jan 1, 1998

By Mark William Withey

"Blasting safety in surface mining is a necessary industrial goal. Proper techniques and disciplinesexercised during the blasting process enhance the probability of achieving that goal.The blasting process is generally a series of repetitive steps performed by all blasting technicians.Because habits formed during this process influence safety, production and cost, proper habitsbecome compulsory."

Jan 1, 1995

By John Petty, John Loviza

As a blaster, have you ever had that uneasy feeing in the pit of your stomach as a codes enforcement official drives onto your jobsite? Have you ever needed an ally in a court of law against an unjust damage claim? Have you ever wished for a better and more open relationship with the guys who wear the badges?

Jan 1, 1996

By X Meng, W. A. Hustrulid, M. K. McCarter

Rock excavation in both surface and underground mining is largely accomplished using the drill and blast technique. At the perimeter of such excavations, cautious blasting procedures are often employed to minimize unwanted damage to the remaining rock. Of the several different techniques available, the use of explosive charges with a diameter smaller than the holes in which they are introduced (so-called decoupled charges) is the most common. In spite of the long and widespread use of the technique, a technically sound basis for relating the borehole wall pressure to the explosion pressure is still lacking. Such a relationship is required for optimal design

Jan 1, 2005

By David G. Borg

Emulsions explosives, like slurries or water gels, are water based explosives. Emulsions were first introduced as a packaged blasting agent in the late sixties. Since then, many new variations have been developed, from small diameter detonator sensitive products to bulk loaded anfo/emulsion blends. Explosive detonation characteristics such as velocity of detonation, density/sensitivity relationship, strength, and water resistance along with how they relate to the type of rock and type of application will be presented. Various methods of sensitizing such as glass microspheres and chemical gassing along with product limitations and safety recommendations for bulk loading emulsions will also be presented.

Jan 1, 1994

By S A. Steyn, P Terrett

Air decking has become a widely practised method internationally for modifying fragmentation results and providing cost savings from reduced explosive consumption. Duvha has been applying air deck technology to overburden and midburden blasting for a few years. A thorough evaluation of air decking at Duvha has been made by instrumenting a number of blasts and analysing costs from direct savings in reduced explosives costs to savings in improved dragline productivity.

Jan 1, 1995