Search Documents

By Peter Riccio

Oxiana Sepon?s mineral processing facility in south central Laos produces copper cathode using leach-autoclave-SX/EW flotation technology. Pyrite recovery in the flotation circuit is critical to the operation, as it is used to generate acid for the leach circuit. However, low pyrite recovery has been an ongoing challenge in the flotation circuit. Tailings characterization work done by Ian Wark Research Institute showed that the pyrite losses to the tail are made up of a combination of coarse liberated particles and finer particles that have been coated by clay fines. In December of 2005, a joint Cytec-Oxiana technical program was initiated to address the pyrite recovery issue. A series of diagnostic tests were performed in the Cytec Stamford Research Facility using synthetic plant water showing that the collector was precipitating as a metal salt, and was un-available for mineral attachment. The tests also identified several collector chemistries that would likely be robust in the Sepon low pH, high dissolved metal ion environment, and will not complex with ferric, ferrous, or copper in solution. With the support of the Sepon on-site engineers, an extensive, successful laboratory program was completed, which then was followed by on plant testing that showed a step wise improvement in pyrite recovery.

Jan 1, 2014

By G. Demi, G. Belardi, N. Shehu, S. Cico

The physico-chemical interaction between minerals such as olivine, chromite and serpentine and the ions most commonly present in solution, like Ca and Mg and flotation reagents such as EDTA and oleic acid was investigated. The study was conducted via release tests, electrophoretic measurements and microflotation of selected minerals coming from the Kukes deposit (Albania). The results were confirmed by means of beneficiation tests on various types of ores, from the Kukes (Kalimash), from Bulquiza area and from the Rizo deposit (Greece). It has been demonstrated that when Na-K Oleate is used as collector chromite, olivine and serpentine can be separated at pH = 2.5 and/or 5.5 employing EDTA (EthyleneDiamineTetraAcetate) on previously deslimed material. This approach ensures flotation concentrates with a Cr2O3 content about 50%, at a recovery in excess of 65%.

Jan 1, 2003

By Willis Forsling, Prabhakar Swarna, Hanumantha Rao Kota

The solubility of wollastonite and its Hallimond flotation behavior as a function of dodecylamine concentration and pH are examined. The flotation response is characterized by adsorption and surface energy in the presence of amine. The methods of UV-Visible and FT-IR spectroscopy for adsorption and sessile-drop contact angle for surface energy estimation are employed. The results of wollastonite dissolution clearly showed its non uniform dissolution. The surfaces are depleted with calcium ions and became rich in silicon within 10 min of flotation time. Maximum flotation of wollastonite corresponds to a half monolayer coverage of amine, which is substantiated by the surface energy parameters. A good correlation between flotation, adsorption and surface energy as a function of amine concentration and pH was observed. The sudden increase in wollastonite flotation and amine adsorption at and above 5x10-5 M initial amine concentration is thought to be due to two-dimensional precipitation of amine on surface in accordance with the recent 2D-3D precipitation model of amine adsorption on silicate minerals.

Jan 1, 2003

By D. J. Hallbom

The ?yield plastic? rheological model describes the flow behaviour of a variety of non-settling suspensions, including many types of mineral slurry. The current paper presents the laminar flow relationship (pressure gradient vs. flow rate) for a yield plastic fluid flowing through a pipe or cylinder. Simplified algebraic equations, suitable for engineering purposes, are presented for yield plastic fluids with values of the scaling factor in the range that includes most industrially important slurries. The laminar pipe flow relationship is one of the most important fluids engineering calculations. It may be used to determine the rheological parameters of a material in a capillary rheometer or flow loop. If the rheology is known, these relationships may be used to determine the laminar flow pressure gradient in pipelines of various sizes.

Jan 1, 2014

By S. Mohanta

In composite washeries optimization of operating parameters to achieve maximum clean coal yield at the desired clean coal ash level is a major problem. This problem is more acute in countries like India, which have predominant reserves of difficult-to-wash coals. The constrained operational parameters of washing for some equipments make it more severe. In addition to this, the dependence of separating performance of different equipments upon various variables aggravates the situation. Here an attempt is made to find a numerical solution to get maximum yield and minimize the difference between the actual and the theoretical yield. The solution is arrived through constrained non-linear optimization of a multivariable objective function that utilizes spreadsheet tools; the method accommodates any number of source coals or washing size fractions. By using a designed Ep value the predicted yield of composite clean coal has been calculated and the yield is optimized subject to constraints on both the ash and specific gravity. It is shown that operational constraints of different washeries in the composite plant that utilizes gravity separation methods can also be over-come. The technique offers the coal preparation engineer an effective and straightforward method for determining the optimum cut-points of separation for different coals or blended coals to obtain maximum product yield at a specified level of ash content.

Jan 1, 2014

By R. Kobialka

In the article results of experiments over jaws? linings in jaw crushers with different shaping of working surface were presented. Following sets of jaws were under investigation: immobile plain jaw and moving jaw with grooving surface. Grooving jaws have groves with circular, triangular and trapezoid cross section. In order to evaluate efficiency of comminution both the grain composition of product and the content of irregular grains were determined, as well as the size of crushing forces and process efficiency were measured. For the combination: plain jaw with grooved one, a good results were obtained as regards the grain composition of product and the content of irregular grains. Crushing forces were higher at crushing with mixed types of jaws (the one plain, the second grooved), in comparison to crushing with using both grooved jaws. Efficiency of the process was definitely higher for mixed jaws.

Jan 1, 2014

By Z. F. Hu

Tourmaline has the characteristics of piezoelectricity, thermoelectricity, spontaneous polarization and far-off infrared radiations. Ultra-fine powders of tourmaline have extensive applications in the fields of electron, chemical and environment protection, as well as health protection. The preparation technology of ultra-fine tourmaline powder is discussed. The key equipment of a pilot plant for producing ultra-fine tourmaline powder with jet mill and stirred ball mill is described. Using this pilot plant facility it is possible to produce tourmaline powder with particle size smaller than 100 nm, and a continuous production process can be realized. The final powder product has many superior performance such as high whiteness and large specific surface area, and it?s a negative ions emission can reach the value of 7190 ions per cubic centimeter.

Jan 1, 2014

By Andrew Logan

Newcrest has a strong history of growth over the past 20 years, yielding value from previously marginal ore bodies. We have grown regionally in Asia Pacific through our operations in Australia, Indonesia and Papua New Guinea, and also established a beachhead in West Africa. The company has a reputation of realizing value from large, low-grade deposits adopting step change approaches. Newcrest is focused on an overall strategy of gold, low cost, long life and moderate growth. Capability step changes play a large delivery role. They transition from a business offline-to-online approach as opportunities mature. Newcrest believes in a) Knowing what ?good? looks like, b) An open innovation approach to actively working with others, c) The leap frogging leverage of making the ?old new again?, d)An adopt-adapt-develop methodology enabled by rapid prototyping/piloting, e) Getting our handsdirty with test work and plant analysis, and f) Staying focused on a few high business leverage areas. This paper describes Newcrest?s approach and our experiences in establishing renewed metallurgical processes, specifically aimed at increasing innovation adoption. Some of our step changes discussed include: 1) Early waste rejection to avoid high energy processing downstream, 2) Broader gold product channels to reduce site based processing needs, 3) Lower energy processing, and 4) Geo-Metallurgy approaches. Keywords: Newcrest, gold, step change, open innovation, adopt, adapt, develop, offline, online, prototyping, old new again, waste rejection, low energy, geo-metallurgy

Sep 1, 2012

By C. Dorfling, C. A. Snyders

South Africa has extensive mineral processing and extractive metallurgy capacity and infrastructure for metal production from natural resources. Decreasing ore grades, increasing labor costs, and more stringent legislation have made economic metal production from primary resources challenging. Opportunities exist for metal production from secondary resources such as mining wastes and end-of-life consumer goods. The objectives of this study were to evaluate the current status of metal production from secondary resources in South Africa and to identify potential opportunities for further development. Two main classes of secondary resources, namely mining waste and electronic waste, were considered. Primary metal producers are dominating metal production from mining wastes; several of the gold, platinum and chrome producers operate low risk and low cost tailings retreatment facilities that contribute significantly to their overall production. Further opportunities exist in, for example, the treatment of more than 450 estimated gold tailings dumps in Gauteng, as well as metal recovery from slags and furnace dust. The majority of companies involved with electronic waste recycling in South Africa focus on collecting and disassembling; only a few perform preliminary physical processing, with the recovered fractions then being sent overseas for metal recovery. Projections are that the rate of waste generation will increase significantly and that treatment will become critical to comply with more stringent environmental legislation. Projects related to process development, techno-economic evaluations and environmental impact studies for metal recovery from batteries, printed circuit boards, and fluorescent lamps are underway. South Africa is ideally positioned to further explore opportunities for synergistic relations between metal recyclers and primary metal producers. Processing of electronic waste for production of technology metals, for which limited natural resources exist in South Africa, would be a key enabler for local manufacturing industries and expansion of the value chain.

Jan 1, 2018

Beneficiation and dephosphorization of refractory oolitic hematite ore are investigated in this paper. It is shown that single magnetic separation, gravity separation or flotation is unable to recover iron effectively from the ore due to the complex mineralogy. The joint separation by spiral chute-shaking table shows a prospect for the treatment of the ore. An iron concentrate with 58.67% iron grade and 51.93% recovery is obtained by the joint separation of spiral chute and shaking table under the fineness of ?0.074mm 90% and dispersant dosage of 2kg/t for a sample ore of 37.51% Fe and 0.88% P. However, P content in the concentrate is still up to 0.52%. Dephosphorization from the concentrate is hence carried out. The final iron concentrate assaying 59.26% Fe and 0.056% P is obtained when the concentrate obtained by joint separation is leached by sulfuric acid of 1% (mass fraction) with solid percentage 10% at room temperature for 10min.

Jan 1, 2014

By B. McFadzean, P. E. Ngoepe, P. P. Mkhonto, J. Taguta

The adsorption of heterocyclic collectors such 2-mercaptobenzothiazole (MBT), 2-mercaptobenzoxazole (MBO), 2-mercaptobenzimidazole (MBI) and their derivatives on pyrite form a basis in understanding the flotation reactivity that may be applicable in a wide range of sulphide minerals. This study uses a computational and experimental approach to determine the heat of adsorption of MBT, MBO, MBI and modified MBT collectors onto pyrite surfaces. Computational calculations found that the adsorption energies were in the order: MBO > MBI > MBT. The heterocyclic collectors were adsorbed in their thiolate form on the surface. In the case of the pyrite (100) surface, the MBT adsorbed through the exocyclic sulphur atom, while MBO and MBI adsorbed through the exocyclic sulphur and N atoms onto the 5-coordinated Fe atom. The (111) surface was found to be more reactive and different adsorption mechanisms were predicted, where the MBT exocyclic sulphur atom bridged on the 5- coordinated Fe and surface 2-coordinated sulphur atoms, while the N atom adsorbed on the 5-coordinated Fe atom. In the case of MBO and MBI, dissociation of the exocyclic sulphur atom from the collector occurred with subsequent interaction with the surface 5-cordinated Fe and 2-coordinated S atoms. This resulted in the collector carbon atom adsorbing on the surface 2-coordinated S atom, while the N atom adsorbed on the 5-coordinated Fe atom. The adsorption of the modified MBT was found to be more exothermic than the MBT, which showed that introduction of a –CS2 group on the exocyclic sulphur atom improved the affinity of MBT on the surface, and was thus a better flotation collector. The computational results were supported by experimental enthalpy of adsorption measurements and microflotation tests. The chemistry of the heterocyclic thioamides is complicated by the fact that they can exist in a number of tautomeric and ionic forms at different pH’s. This is discussed in relation to the flotation and calorimetric data.

Jan 1, 2018

By S. Q. Zhu

A newly developed coal flotation collector ZFC and its flotation characteristics for five different coals were introduced in this paper. ZFC is an emulsion composed of 27% diesel oil, 70% water and 3% surfactants. The main surfactant is synthesized with oil which is environmental favorable and reproducible. Compared flotation experiments show that, at the same dosage, ZFC give 2%~5% recovery promotion than typical collector with only a slightly ash content increment, but saving 70% diesel oil. Zeta-potential and Wetting heat measurement indicate that the surfactant helps the interactions between oil and coal particles, the industrial application tests in several coal preparation plants demonstrate that ZFC is suitable both in technical and economical aspects.

Jan 1, 2014

By Shobhana Dey

A low volatile medium coking coal from Jharia coal field, India was used for this investigation. The proximate analysis of the sample shows that it contains about 25% ash, 21.4% volatile matter and 52.4% fixed carbon. The sizewise ash analysis of -0.5 mm coal indicates that -0.5+0.15 mm fraction contains lower ash (21.9%) than -0.15 mm fraction (29.7%). The flotation characteristics of the -0.5 mm coal were determined by release analysis. The study reveals that recovery of combustible at 15% ash is about 27% and 43% at 17% ash level. The low recovery is due to the presence of high ash in finer fraction. In order to improve the recovery, the -0.5 mm feed was classified into -0.5+0.15 mm and -0.15 mm fractions, and subjected to flotation separately. The recoverable combustible obtained from the release analysis of -0.5+0.15 mm at 15% ash level is 46%. The effect of collector dosage, frother dosage and aeration rate on flotation was studied. The responses of these variables in collectorless flotation of the -0.5+0.15 mm fraction containing low ash were also studied. A lower aeration and frother dosage favored the generation of clean coal with low ash. The ash content in the tailing stream from -0.5+0.15 mm flotation circuit is close to that of the original -0.15 mm fraction. The former is ground to -0.15 mm and the two fractions are processed together. As -0.15 mm fraction contains relatively higher ash, collector aided flotation using sodium silicate was performed to recover the clean coal with 17% ash. The products of the overall flotation circuit having different ash levels were recommended for use in different applications. The reject from -0.15 mm flotation circuit contained 56.4% ash which can be used for fluidized bed combustion (FBC). This eventually leads to complete utilization of coal.

Sep 1, 2012

By R. A. Kleiv, H. Havskjold, N. Church, T. Malvik, M. Tro, E. Larsen

Liberation is one of the major purposes of comminution in mineral processing. In the simplest form, two or more minerals are present in a particle and have to be reduced such that the individual particles contain only one mineral. The complexity of the mineral intergrowth varies from ore to ore. Poor magnetic separation of iron ore may have many causes. In this paper, the emphasis is given to the problem of fine magnetite inclusions in quartz or other gangue minerals. This is highlighted by two Norwegian cases: one on a magnetite ore and the other on a hematite/magnetite ore. The inclusions in question are so small that they are not liberated by reasonable grinding. In both cases, the result has been either poor recovery or lower grade concentrates than desired. The first example concerns production of direct reduction concentrates from magnetite. Magnetic inclusions in gangue particles will be magnetized enough for the particles to pass into the concentrate. The second example is given a more detailed study, where the problem is caused by silicates with small inclusions of magnetite in a combined LIMS and WHIMS separation. This study included microscopy, Davies tube testing, and magnetization measurements. In particular, large gangue particles with magnetite inclusions were shown to have a tendency to bypass the LIMS separators as drag forces in presence of hematite are large. Such particles will then be picked up by the WHIMS as their magnetization is higher than for hematite. This was demonstrated by Davies tube tests, which indicated that such particles were picked up in preference to hematite particles. However, the Davies results did not give a good quantification. Magnetization measurements of gangue particles with magnetite inclusions was shown to be a better tool to quantify the magnitude of the effect of magnetite inclusions in magnetic separation.

Jan 1, 2018

By I. Y. Titov, Victor D. Samyguin, A. Y. Nikitin

"It is suggested that improvement of separation process efficiency in machines and circuits of selective flotation should be based on application of the principle of technology individualization (PIT). This principle is grounded on the following provisions.The mineral composition of ores is used to establish the correlation between the selective reagent mode and the individual value of hydrodynamic conditions of flotation machines together with individual structure of the process flow diagram. The individuality of all sorts of particles identified by methods of process mineralogy was characterized by their distribution according to the rate of flotation (or spectrum). The spectrum identification is carried out by modeling and by experimental and computational method on the data obtained on various types of laboratory flotation machines.The computer-aided test is used to determine the optimal fraction distribution, which reaches the highest possible level of concentration data. The direction of hydrodynamic factors action on concentration data is estimated based on comparison of design base and experimental spectrum. The improvement of separation efficiency in devices is achieved in special-purpose flotation machines (SFM) the design of which provides optimization of hydrodynamic regime in spatially isolated zones. It is demonstrated that the main parameter of SFM operating mode individualization is the rise rate of bubbles going from the chamber into the froth. During this time the composition of particles optimum for separation is formed on its surface. Additionally, it is necessary to coordinate in the zones the residence time of pulp and foam streams with the air consumption. The improvement of separation efficiency in flotation process flow diagrams may be achieved by making several cascades with SFM installed in them. The individual effective structure of the scheme for a definite ores material composition depends on the ratio of particle varieties in the spectrum and is revealed by modeling."

Jan 1, 2018

By A. V. Bogdanovich

In diamond ores processing, final waste tailings size, rejected to dump, is one of the most important parameters. On one side, it is necessary to minimize losses of diamonds, whose size exceeds 1 mm, on the other side ? to provide for the plant high throughput and sufficiently low capital and energy costs, which is in greater part connected with disintegration process. Extensive laboratory, pilot-scale and commercial-scale dressability studies of different types of diamond ores have been performed at JSC ?Mekhanobr Engineering? in recent years. With that, special consideration was given to determination of the required ores? disintegration size that would provide for a high recovery of diamonds. In diamond ores processing, in order to exclude breaking of large diamonds, stage disintegration is used with regrinding of light fractions and heavy fraction X-ray fluorescent separation tailings. On account of rather weak bonds of diamonds with enclosing minerals, in crushing and grinding of diamond ores, selective disintegration takes place, with aggregates? breakup along plane surfaces of least bonding, which facilitates liberation of diamonds and their transition to free state. Heavy components losses with different sizes of final dump tailings were studied in processing of large samples. It was established, that in order to almost completely exclude losses of heavy components over 1 mm size, light fractions had to be ground to 2.5-3 mm size, while X-ray fluorescent separation heavy tailings of -15+3 mm size do not contain diamonds larger 1 mm in aggregates, and their regrinding does not increase total recovery of diamonds. On the basis of the conducted studies, relationships regarding heavy components and diamonds losses with respect to diamond ores final disintegration size were obtained, providing for more rational organization of the ores disintegration and processing flow sheet. Keywords: diamond, waste tailings size, disintegration process, recovery of diamonds

Sep 1, 2012

By Sarra Scherbakova, Alexander Kurkov, Andrey Egorov

"Deep concentration of iron ores involves extraction, in addition to magnetite concentrate, of hematite and martite concentrates and recovery of other valuable components. A flotation technology was designed specifically for finely disseminated hematite ore, allowing producing saleable hematite concentrate containing 64-66% Fe. The main process challenge is caused by the presence of other ferruginous minerals such as carbonates, silicates, and phosphates, and fine hematite and martite mostly concentrated in the -0.044 mm fraction. Main operations of the processing circuit are removal of slime, flotation to remove impurities (carbonates, phosphates etc.) with an anionic phosphorous collector in an alkaline environment, hematite and martite flotation using same collector in a slightly acidic environment to produce commercial iron concentrate. Tailings of wet magnetic separation of magnetite containing 24.5% Fe and finely disseminated hematite ore containing 51% Fe were processed to produce iron concentrates with a yield of 15% and 50%, respectively, containing approximately 65% Fe and 5% of silica. Hematite flotation tailings had the highest content of gold (up to 0.09 - 0.11 g/t), while in other products it never exceeded 0.02 g/t. Using a Knelson concentrator was able to recover 40 to 45% of the gold into 3.31 g/t Au gravity concentrate. The success of gravity concentration is due to high gravitational contrast of gold to mostly quartz and aluminosilicates in the hematite flotation tailings. In general, the proposed process can be used as a solution to the challenge of selective concentration of finely disseminated iron minerals."

Jan 1, 2014

By Silvia França, Hudson Couto

"In this paper, an alternative beneficiation process was developed to recover nickel minerals from low-grade weathered ores. The studied sample, 0.3% Ni grade, is essentially composed of nickel sulfides (pyrrhotite and pentlandite); magnetite and silicates (mostly talc and amphibolites) are the primary gangue minerals. The particle size distribution was controlled using a grinding operation to avoid producing an excess of fine particles by overgrinding. The sample underwent a grinding step for the fine degree of liberation. The slimes (-20 ?m) were removed via two desliming stages in hydrocyclones (diameters of 1.5" and 2"); the ground material, which was classified in a range of (-150+20) ?m, was processed by column flotation in three different stages: rougher flotation for magnesium silicates, rougher flotation for sulfides, and cleaner flotation for sulfides, using pilot flotation columns (2" and 6" in diameter and 20 ft high). The goal of using the preliminary magnesium silicate flotation step was to remove hydrophobic minerals (mostly talc) that would float naturally with the sulfides, which would decrease the Ni grade in the concentrate, as well as to reduce the MgO content because this compound is considered harmful in metallurgical processes when a grade greater than 9% is used. The final concentrate obtained in the cleaner flotation step reached up to 2% Ni and 7.0% MgO. The global and flotation recoveries in the process were approximately 30% and 60%, respectively, due to the losses of Ni during the desliming process. Despite this low global recovery, the adopted beneficiation process can be considered an interesting alternative to produce nickel concentrate from tailings or waste materials."

Jan 1, 2014

By E. Gock

Based on the scientific investigations on mechanochemical synthesis of metal sulphides from metals or metal compounds and sulphur or sulphur compounds, the article describes the industrial production of nanoscale metal sulphides. Special operational conditions such as inert atmosphere, size and type of the grinding balls, grinding time and specific energy input are taken into consideration. A system configuration for the manufacturing of sulphides at a capacity of 100 kg/h is presented.

Jan 1, 2014

By T. Chmielewski

Unique mineralogical and petrological properties of black shale in the copper ore deposit of the Foresudetic Monocline (SW Poland) resulting from three lithological layers have been described in terms of its unfavorable behavior in the ore processing circuits. A concept of processing of a part of the black shale fraction from the flotation circuit of the concentrating plant by separating a by-product enriched in the shale matter was presented. This by-product represents the tailings of the first cleaning flotation and, as a hard-to-treat circulating middlings, overload the cleaning operation in the flotation circuit. It was found that the investigated by-product cannot be effectively up-graded using standard xanthate flotation. This is due to a fine dissemination of sulfide minerals in the dolomitic and clay shale particles significantly enriched in organic carbon. The content of the organic carbon is similar to that in the petrographically "pure" black shales. After a comprehensive examination of the shale by-product it was recognized that the investigated middlings can be regarded as a specific shale concentrate for individual processing. The effect of non-oxidative leaching of middlings with sulfuric acid on their further flotation was presented. It was shown that non-oxidative leaching is a selective process, in which calcium and magnesium carbonates decomposition leads to effective liberation of sulfide minerals which were finely disseminated in the hydrophilic carbonate gangue. Leaching of the flotation feed with sulfuric acid selectively decomposes carbonate minerals and consequently enhances flotation results. Saturation of leaching slurry with gaseous carbon dioxide favorably creates non-oxidative conditions and leads to a great decrease of the electrochemical potential of sulfide particles as well as hinders their solubilization. Partial carbonates leaching from middlings resulted in evident liberation of valuable minerals. Consequently, it resulted in an increase of both recovery and grade of concentrates obtained by flotation of shale by-product after non-oxidative leaching.

Jan 1, 2014