Search Documents

By S. Banisi, O. Farshid, M. R. Rozebehi, A. Bahar, A. Arghavani, M. Mahdavi

At the rougher flotation circuit of the Miduk copper concentration plant (Kerman, Iran) five column cells (CISA) with the diameter of 4m and height of 12m using static mixer type (MicrocelTM) spargers have been installed. Based on the initial design, columns should accept a feed rate of 625 t/h with 80% passing size of 90 µm and solids concentration of 28% and produce 88% of the plant concentrate (i.e., 22 t/h) containing 32% copper. Due to mechanical and processing problems this objective was never realized and theses columns were remained out of operation from the commissioning time (2005). A new attempt with the aim of returning these cells into operation started in 2013. The results of an extensive study indicated that spargers plugging due to the entrance of small amount (2 kg) of coarse particles (up to 2.5 cm) because of usual problems at the plant environment was the main reason of columns non functionality. With a change in the recycle pump inlet design to the column, which prevented the entrance of coarse particles to the spargers, the operation of the column significantly improved. It was found that in order to have a stable operation of the columns at the rougher stage the feed rate for each column should be reduced from 125 (design) to 70 t/h. The air superficial rate had to be also reduced from 1.9 (design) to 0.6 cm/s. A period of 10 days of continuous operation showed that the carrying capacity was 0.23 (g/min/cm2) which was significantly lower that of the design value (i.e., 0.58). The gas hold up was found to be lower than 10% beyond which columns started to move to the turbulent state indicated by "boiling" froth. The average life time of spargers was determined to be 20 days which considered to be very short. The average recovery and concentrate grade of these columns were found to be 68% and 32%, respectively. The high wear rates of spargers, unusually high level of maintenance and supervision needed and instability of the operation made the plant managers not to use column cells as the roughers.

Jan 1, 2014

By Eduard Stefanescu, James M. Mwase, Egon Sehner, Stoyan Gaydardzhiev

"The study is focused on investigating the production of synthetic rutile of 95% purity or higher from a Norwegian ilmenite ore concentrate. This was to be achieved using a sequential process involving oxidative-reductive roasting at 975°C, followed by magnetic separation to further concentrate the sample and finally leaching with 20% HCl to remove mostly Fe-based impurities leaving behind synthetic rutile. The key process parameters considered were roasting time (1 and 2 hrs), leaching temperature (100, 125 and 145°C), pulp density (15 and 25wt%) and leaching time (3 and 6 hrs). The option of directly leaching the concentrate without pre-treatment was also evaluated. Test work was conducted using samples screened to a size fraction of 105-212 µm. Samples were leached in a 1 L glass autoclave. The reactor was hermetically sealed and thus the resulting pressure was not controlled but was dependent on the process temperature. The product from leaching was calcined and analysed via XRD and SEM to determine the purity of the product. The magnetic separation step was found to be ineffective and discontinued early in the study. Thus far a product with 97% synthetic rutile purity as analysed by SEM has been produced by directly leaching the concentrate at a temperature of 145°C, pulp density of 25wt% and leaching time of 6 hrs.INTRODUCTION The study investigates the use of a process route comprising oxidative-reductive roasting, followed by magnetic separation and then hydrochloric acid leaching and calcination to produce synthetic rutile from ilmenite concentrate. The grade of synthetic rutile produced should be suitable for chlorination to produce pigment grade TiO2. Hence the proposed process should produce a product consisting of no less than 95% synthetic rutile. Additionally, the product should have no more than 1.5wt% combined content of CaO and MgO (Zhang et al., 2011) as they tend to form high-boiling-point chloride leading to the malfunctioning of fluidized bed chlorinator (Cardarelli, 2008). Finally the product should have no more than 2.1wt% of Fe2O3."

Jan 1, 2018

By I. A. Makalin, V. N. Yakovlev, S. V. Imangulov, I. V. Zyryanov

"The presented studies aimed at solving the problem of recovery of low-luminescent diamonds, which are not recovered using X-ray luminescence method of processing of diamond-bearing ore. The purpose of the studies is the determination of possibility and feasibility of recovery of such crystals using dual-energy X-ray transmission separation technology. In preparation for studies methods were developed for testing technical and process parameters of XRT-400 Aliud GmbH (Germany) sorter, manufactured according to design specifications of Yakutniproalmaz Institute, and XRT/D TOMRA Sorting Solutions GmbH (Germany) sorter, designed for processing of -50+5 mm ore, as well as RGS-1M, RGS-2 X-ray sorters, developed by JSC NPP Bourevestnik (St. Petersburg) in cooperation with Yakutniproalmaz Institute, for material size of -6+3 mm. In 2018, in-process tests of RGS-OD-3 X-ray sorter prototype on material size of -3+1 mm are scheduled. Studies to determine the content of low-luminescent diamonds and feasibility of their recovery using XRT-400 and XRT/D sorters at the Processing Plant #3 of Mirny Mining and Processing Division (MPD) were carried out. The results of the studies confirmed presence of such diamonds and possibility of their recovery using the dual-energy X-ray transmission method. In-process tests of RGS-2 X-ray graphic sorter were carried out at the Processing Plant #16 of Nyurba MPD. According to the results of sampling of RGS-2 sorter separation products, the recovery of -6+3 mm sized diamonds from tailings of X-ray luminescence sorters was achieved at the level of 96%, while the diamonds recovery was 98.5% in value terms, the concentrate yield was 0.1%. In-process tests of RGS-1M sorters at final recovery of the grease separation concentrate at the Processing Plant #3 of Mirny Division were carried out. Recovery of low-luminescent -6+2 mm sized diamonds by RGS-1M sorter amounted to 92.4% for single operation, and with the double control operation reached 99%. As a result, -6+2 mm sized base product recovery increased by 0.2%."

Jan 1, 2018

By V. A. Ignatkina, V. A. Bocharov, T. I. Yushina, I. M. Petrov, A. A. Kayumov

"The purpose of this research was aimed at increasing recovery of metals from rebellious sulfide polymetallic ores of nonferrous and rare metal deposits. The ores under consideration have common processing features, including textural and structural complex characteristics, irregularity of impregnation and wide range of grain size, up to nanoparticle size, variable complex mineral composition, low content of precious metals etc. This all predetermines the need for advanced processing schemes with deep selective liberation and separation of minerals with intercycle release into rough concentrate and fractional products with the use of multi-stage cycles of individual dressing, based on an optimum combination of various integrated beneficiation and hydrometallurgical processes. The application of existing standard processes does not enable the production of high-grade selective concentrates without reducing the recovery rate due to incomplete separation of fine mineral intergrowths and overgrinding of brittle ore and rock minerals.The combined beneficiation processes for such type of resources, aimed at increasing recovery of nonferrous, rare, and precious metals are based on flotation methods in combination with gravity concentration to produce rich rough collective or selective concentrates, comprising readily floatable mineral fractions. At the same time, hardly recoverable and non-separable mineral associations are released into separate concentrated products for following dressing by individual processes. The proposed combined process provides for successive selective liberation of minerals with release of rich readily recoverable mineral fractions at the preparation and ore beneficiation stages. The hardly recoverable mineral associations shall be released in subsequent operations with the use of dressing, based on a combination of beneficiation and pyro- and hydrometallurgical methods."

Jan 1, 2018

By A. V. Bauman

"Important for thickening processes is the ability of slurries to form under certain conditions aggregation and sedimentation stable systems. Substantial part of difficult to sediment solid particles in such systems may be in colloidal state. The technique to study the sedimentation and aggregative stability of the slurry developed by the author with co-authors makes possible to define kinetics of changes in the aggregative stability of the system with solid phase varying concentration in it and produce data on sedimentation stability of the system in preliminary investigation of the thickening process. Research of aggregative and sedimentation stability of the slurry complement standard methods of laboratory studies to prevent errors in development of water-slime thickening balance and water circulation to design new and upgrade existing processing plants. Statistical analysis of process audits of more than one hundred upgraded and newly commissioned processing plants carried out in recent fifteen years showed that more than two-thirds of problems arising in commissioning the processing plants are associated with misdesign and errors in thickening and water circulation system. Among the main reasons of process design failures are: non-conformity of actual characteristics of the raw material to design characteristics, low quality of preliminary studies at the stage of sedimentation process simulation, design failures, wrongly selected equipment for the thickening and water circulations systems. As of today a number of problems associated with laboratory studies of sedimentation process, first of all, with interpretation of precipitation curves produced at the stage of laboratory refinement of the thickening process have been pinpointed. (Bauman A.V. Outstanding issues in design of thickening and water circulation diagrams in processing plants // Ore processing. 2016. ?3 P. 58-62) ?????? ?.?. ?????????? ??????? ?????????????? ???? ???????? ? ??????????? ?????????????? ??????. // ?????????? ???. 2016. ?3. ?. 58-62))"

Jan 1, 2018

By Choi Sang-Ken, Chung Hun-Saeng, Kim Byoung-Gon, Park Chong-Lyuck

Fine grinding of crystalline graphite was conducted using a dry attrition mill with a vacuum system to investigate the characteristics of size reduction. Low pressure and high temperature conditions in the grinding mill were found to greatly improve the efficiency of the size reduction of graphite. Natural flaky graphite of .100 mesh was ground into sub-micron sizes, then over 90% of the product were able to be reduced below 1?without disrupting their crystallinity in a short period of time. Reducing the atmospheric pressure in the grinding environment promotes the removal of chemical species such as oxygen and water molecules adsorbed on the graphite particle, resulting in effective size reduction while maintaining the crystallinity of graphite.

Jan 1, 2003

By B. Z. Wu

The flotation of low-grade zinc oxide ore which from Guizhou has been researched by sulfuration- amine method. The experimental result indicated that when pH of pulp was 11, good flotation index can be achieved by using sodium silicate as dispersant, mixed amine as collector, and the do-sage of sulfur sodium was 6kg/t, and the recovery of zinc can be heightened by using copper sulfate as activator and Hydroxamicacid as collector. When the zinc feed grade was 4.84%, the zinc concentrates with grade of 39.23 % and recoveries of 75.17 % were obtained by adopting this technics.

Jan 1, 2014

By Kazutoshi Haga, Batnasan Altansukh, Shirchinnamjil Nyamdelger, Atsushi Shibayama, Narankhuu Ariunbolor, Gunchin Burmaa

In this study, the authors investigated the capability of an acidic thiourea solution and silicon-organic polymers (PSTM-3c, PSTM-3T) as ion-exchange resins to recover of gold from gold-bearing ore concentrates. Firstly, elemental gold present in flotation concentrates was dissolved by leaching with a solution of nitric acid and thiourea under the optimized conditions. The best result on gold thiourea leaching was obtained under a nitric acid concentration of 2 N, thiourea concentration of 2 %, and oxidant (Fe2(SO4)3) concentration of 3 %, solid:liquid ratio (S:L) of 1:20, leaching time of 6 hours at 20 °C with a gold recovery of 93.7 % for a gold flotation (unroasted) concentrate. For the roasted gold concentrate, the dissolution of gold was 94.8% under the optimized leaching condition as nitric acid concentration of 0.5 N, thiourea concentration of 2 %, and the oxidant concentration of 1 %, S:L ratio of 1:10, leaching time of 4 hours at 50 °C. Secondly, a series of sorption tests was carried out on a pregnant leach solution containing gold complex Au[S=C(NH2)2]2+ using silicon-organic polymers (PSTM-3c and PSTM-3T), respectively. The effects of solution pH, adsorption time and temperature in the sorption process are also studied. As the results, the PSTM-3c and PSTM-3T polymers were adsorbed about 94.4 % and 95.1 % gold from the pregnant leach solutions under the optimum sorption conditions, respectively. It was found that the both PSTM-3c and PSTM-3T polymers were effective for the recovery of gold from the pregnant leach solution of thiourea. Adsorption activity of the PSTM-3c and PSTM-3T polymers was confirmed by new peaks near 1700 cm-1 in the FT-IR spectrum of the gold-adsorbed polymers, respectively.

Jan 1, 2014

By M. Ito

The authors have developed the RETAC jig (a modified TACUB jig) and have reported that the RETAC jig can separate relatively low density particles such as plastics. To further improve the separation ability, a hybrid jig (a RETAC jig with an air bubbler under the particle bed), which can separate plastics having similar specific gravities by the differences in the wettabilities of the particles was developed. Surface modification of plastics with similar wettability enabling separation in the hybrid jig and the effects of wettability control of the plastics using reagents are reported.

Sep 1, 2012

By W. H. Cheung

Nickel (Ni) plays a major role in the production of steel and other major alloys. There are two sources of Ni: laterite and sulphide ores. Global reserves of sulphide ores are being rapidly depleted, while there are enormous reserves of Ni laterite, much of it in Australia. As well as being present in huge amounts, Ni laterites have the advantage of containing cobalt (Co), a valuable mineral. Over the past decade, these factors have been driving the industry to explore the processing of Ni laterite. A route that has been used commercially in processing nickel laterite ore involves the thermal activation of the minerals by pre-reduction followed by ammoniacal leaching (Caron). Although this process has been effective in processing the goethite rich laterite minerals, the higher-grade serpentine-based minerals have been shown to be less susceptible to this process. This has been attributed to the formation of inert olivine phases. In this study, we examined the use of an alternative lixiviant, sulphuric acid, in leaching pre-reduced limonite and weathered saprolite nickel laterite ores. The specific aim of this study was to examine the sulphuric acid leaching of Ni and Co from pre-reduced laterite minerals, and to understand the role of mineral transformations in this metal dissolution. Synchrotron based X-ray diffraction was used to examine the transformation of goethite (FeOOH) to spinels and serpentine mineral ((Mg,Fe)3Si2O5(OH)4) to olivine. Reduction tests were carried out using CO and CO2 reducing gas mixtures and temperatures from 400 °C to 700 °C. The rate of formation and disappearance of specific Bragg peaks during reduction of specific minerals were used to derive an understanding of these solid-state reactions. Laboratory based reduction tests and leaching in sulphuric acid were used to validate the effect of these mineral transformations. The results suggest the versatility of sulphuric acid in leaching nickel from spinels and olivine, which was achieved at the expense of lower selectivity. Cobalt dissolution was found to be dependent on the nature of ferro-cobalt alloy formed during reduction.

Jan 1, 2014

By Kazutoshi Haga, Batnasan Altansukh, Atsushi Shibayama

Results of flotation process combined with atmospheric leaching and high pressure leaching for recovery of copper from low-grade silicate-copper ore have been presented in this study. The low-grade copper ore contains a small amount of copper (0.42 mass %), iron (4.6 mass %), and silicon (38.3 mass%) and among many other metals (Al, Ca, K, Mg, Na, Ti and S). The main mineralogical constituents of the copper ore are calcium aluminosilicate (Ca(Al2Si2O8), amesite (Mg2Al2SiO5(OH)4) and gypsum (CaSO4×H2O), and quartz (SiO2) as resulted from the alteration of an igneous rock. This study has shown that about 92 % of copper can be recovered with a maximum copper grade of 4.2 mass% in a froth after 15 minutes of flotation at pH 8.5 when used potassium amyl xanthate as a collector, MIBC and Dow-froth 250 as frothers and calcium hydroxide as a pH adjuster. The images of bubbles in the cell during flotation process were recorded using a high-speed camera. The froth concentrate with average copper grade of 2.0 mass% was further processed by atmospheric leaching with a solution of sulphuric acid and hydrochloric acid, respectively and high pressure leaching with sulphuric acid solution. As a result, leaching rate of copper reached about 60 % in an atmospheric leaching with sulphuric and hydrochloric acid respectively, whereas the rate can reach more than 70 % by autoclave leaching at high pressure under the controlled condition. A process to recover of copper from its low-grade ore can be developed by optimization of flotation combined with acid leaching.

Jan 1, 2014

By Claudio Bisso, Javier Vargas, Charles Lozano

"This paper summarizes the activities performed to predict SAG milling throughput at Minera Esperanza. Having highly reliable geometallurgical models aided by the new computer tools and specific metallurgical testing to rely on has become a major issue in recent times due to their impact on the business. Minera Esperanza’s SAG throughput model was constructed by characterizing the ore feed and operational parameters of the plant. Producing a robust model required satisfying number of requirements for the parameters used for both the ore and the plant as follow: 1) geologic and geometallurgical characterization parameters; and 2) parameters of a plant running at the rated production under optimum operating conditions. Obtaining these parameters required increasing the quantity of samples and metallurgical testing through drilling campaigns, mapping the drill holes and putting samples through various comminution tests while sampling all operational flows at the plant to obtain the metallurgical information for the operational parameters. The information was entered on the JKSimMet software to enable a throughput model to be developed to output SAG mill throughput predictions that are very close to actual throughput figures, i.e., accurate within a range of 2% on a monthly basis."

Jan 1, 2014

By F. Xie

Low gold and silver leaching kinetics has been commonly observed in traditional gold-silver cyanidation process, especially in those heap-leaching operations. The reactivity and availability of oxidant was believed to be the critical limitation for gold and silver dissolution. The occurrence of silver sulfide such as acanthite (Ag2S) in the ore may also result in low overall silver extraction. Leaching of gold and silver sulfide in the ferricyanide-cyanide solution has been investigated through rotating disc tests and the assistant effect of ferricyanide on increasing the dissolution rate of gold and silver was noticed. The potential use of ferricyanide as an auxiliary oxidant in gold/silver cyanidation process was proposed based on the results of leaching of gold-silver ores.

Jan 1, 2014

By Y. Y. Zhou

This paper introduces the application of CRIMM high-gradient magnetic separator in refinement of feldspar powders as well as the supporting technical outfits needed by the refining process with the high-gradient magnetic separator as main equipment. It could reduce the content of Fe2O3 to 0.03% with a deferrization rate of 85.88% from the feldspar raw ore containing 0.17% Fe2O3by using the above refining technology, producing an ultrapure feldspar product.

Jan 1, 2014

By Daniela Campos, Aldo Casali, Gonzalo Montes-Atenas

The understanding of the effect of the major variables influencing the froth flotation performance may allow both to predict and to identify best operating conditions towards optimizing the process efficiency. The aim of this research work is to model the effect of dissolved oxygen onto froth flotation performance. Experimental pilot plant results were obtained from a continuous circuit consisting of a ball mill and a rougher bank of four flotation cells. A series of flotation experiments were run with different conditions of dissolved oxygen keeping constant most of other operating conditions. Variables difficult to control were measured or estimated. A set of mathematical models suggested in the published literature were tested. It was found that the copper recovery results were highly sensitive to the concentration of dissolved oxygen. The latter confirmed the reactions mechanisms associated to the collecting capabilities of current flotation reagents used in the flotation of copper sulfide ores. On the contrary, the results of molybdenum recovery varied non-linearly with changes in dissolved oxygen which could not be explained directly in terms of the computed specific rate constants. The error analysis confirmed that Klimpel continuous model exhibited the best specific rate constant correlation with molybdenum recovery data. Lastly, the classic particle force balance equations indicated that the adjustments of estimated mineral liberation with experimental data exhibited a turning point when passing from highly liberated to low liberated particles. The values of recovery for such turning point correlated well with the concentration of dissolved oxygen. The results indicated corrections due to changes in the dissolved oxygen must be incorporated in future froth flotation descriptions.

Jan 1, 2014

By Ming’an Wei, Chuanyao Sun, Zhenguo Song, Zengwen Dou, Yangge Zhu

"The effects of pH value and dissolved oxygen(DO) in the pulp to the Eh and flotation recovery of pyrite were investigated using potential online detection system. The effects of DO on the Eh and flotation recovery were tested which DO changed from 0.5mg/L to 19.5mg/L in six different pH buffer flotation systems (pH: 4.00, 5.62, 6.86, 9.18, 10.01 and 10.96 respectively). Results of potential detected online demonstrated that the pyrite electrode has nearly the same response to potential as with platinum electrode for the FeS2-xanthate-H2O flotation system under the study conditions. Pulp potential and recovery of pyrite were remarkably influenced by pH, both of them decreased with the increasing of pH and, especially, sharp decreased after pH above 9. As the concentration of DO was increased, the Eh was also increased in all the six different buffer solution, while the flotation recovery was decreased. And the amplitude of variation for Eh was not obvious in acidic and neutral solutions, but on the contrary, the change for flotation recovery was remarkable in neutral and alkaline conditions. This may indicate that the flotation of pyrite will be deteriorated in alkaline and high DO concentration conditions."

Jan 1, 2014

By Leon Lorenzen, Trevor J. Britz, Pierre J. Van Zyl, Ellis R. Els

Enhanced granulation of UASB granules was tested on pilot scale with two different test reactors (about 5 litres capacity each). Sludge from a local sewage works was used, with peach cannery effluent as carbon source. Cyclic motion of the reactor contents, and a daily replenishment of feed material create the necessary stress conditions for enhanced growth. Sizable granules, bigger than 0.5 mm, were produced within 20 days. Of the two reactors tested, the reactor equipped with a horizontal agitation shaft proved more effective.

Jan 1, 2003

By Kazutoshi Haga, Atsushi Shibayama, Altansukh Batnasan

The objectives of this study were to propose a viable alternative method for recovery of precious metals such as gold (Au), silver (Ag) and palladium (Pd) from waste printed circuit boards (WPCBs) and to regenerate the spent lixiviant solution for reuse. The proposed method generally consists of several steps as follows: 1). iodine-iodide leaching for metals extraction; 2). separation and recovery of precious metals and metal impurities from a pregnant leach solution; 3). regeneration of the spent iodine-iodide solution/lixiviant. In this method, more than 99% of Au leaching was achieved in the iodine-iodide solution from the solid residue of WPCBs that was obtained via sequential processes including incineration at 800 ?C and high pressure oxidative leaching with a diluted sulfuric acid at 120 ?C, while the leaching of Ag and Pd was less than 1%, respectively. Besides Ca, Cu, Ni, Co and Zn as main metal impurities, leaching efficiency of other metals did not exceed 1%. The precious metals and base metals as metal impurities present in the pregnant leach solution were separated and recovered by precipitation using L-AA and NaOH solutions. About 99.8% Au, 81.7% Ag and 72.8% Pd were recovered from the pregnant solution at pH of 2 with the addition of 0.1 M L-AA as precipitating agent. The remained small amounts of precious metals and metal impurities were precipitated at pH 13 using 1 M NaOH. The spent lixiviant after sequential precipitation was regenerated in the presence of hydrogen peroxide, hydrochloric acid and potassium iodide. It was revealed that over 90% of gold could be extracted from the residue of WPCBs with the regenerated lixiviant solution.

Jan 1, 2018

By I. A. Podkamennyi, O. E. Kovalchuk, G. P. Dvoychenkova

"Using the methods of electron microscopy and IR spectroscopy, mineral components in the run-of-mine kimberlites and on the surface of diamonds were identified. The mechanism and sequence of mineral formation on the surface of diamond crystals were established. Systematization and classification thereof were undertaken for the first time ever.INTRODUCTION The high content of diamonds sized -5 mm in the kimberlite ores of Western Yakutia determines their processing depth in the size class 0.5 mm and finer [1, 2]. These diamonds are recovered by grease and froth separation based on the natural hydrophobic properties of the crystals. When refractory altered kimberlite ores are fed into the industrial process, the performance of grease and froth separation of the diamond ore greatly deteriorates. [4, 10, 15, 17]. Altered kimberlites are known to contain up to 90% of secondary minerals. This reduces by up to 40% the recovery of diamonds by grease and froth separation. [6].Diamond crystals from the grease and froth separation tailings were investigated. On the surface of the examined diamonds, hydrophilic mineral formations were identified, responsible for reduced recovery by physicochemical separation methods [3, 12, 18]. The aim of this study was to identify and describe the relationship between the composition of kimberlite ores and mineral formations on the surface of diamond crystals in order to systematize, classify, and then develop methods of removal in grease and froth separation processes. MATERIALS Following materials were examined in this study: - kimberlites of various material composition, - resulting slimes, - diamond crystals from kimberlite ore processing products."

Jan 1, 2018

By A. Üçyildiz

Magnesium borates of varying compositions and properties are synthesized using different reagents and methods for the possible potential uses as termoluminescent material, anti-wear and anti-friction additive, fire retardant, catalyst for the conversion of hydrocarbons, whisker material and ferroelastic material. In the current work, the conditions for synthesizing MgB4O7 compound by high-temperature solid-state reactions were investigated using boric acid and magnesium oxide as the starting materials. The MgO:B2O3 mole ratios applied in the experiments were 1:1, 1:2, 1:3 and the thermal behaviours of each mixture were studied between 25~1200°C by TG/DTA analyses under static air atmosphere to find out the probable formation temperature of MgB4O7 phase. Considering TG/DTA results, freshly prepared boric acid and magnesium oxide solid mixtures were heated at predeter-mined temperatures and the phases were identified by XRD analyses. Accordingly, MgO:B2O3 mole ratio of 1:2, heating temperature of 950°C and a reaction time of 2 hours were selected as the optimum conditions for the formation of maximum amounts of MgB4O7. After obtaining solids prepared at the pre-determined optimum conditions, their chemical composition, IR spectrum, TG/DTA pattern, B.E.T. surface area value, particle size distribution and SEM images were deter-mined to point out the possible use areas. Experimental results showed that it was not possible to obtain pure product at the optimum conditions due to formation of minor amounts of t-Mg2B2O5 and the presence of some unreacted B2O3. The product synthesized has the potential for use as a corrosion inhibitor on some metal surfaces.

Jan 1, 2014