Search Documents

By Freddy Pøhner

The paper describes recent advances in the technology for mapping of the seabed with acoustic instrumentation. These instruments are typically single beam echo sounders, multibeam echo sounders and high resolution sub bottom profiler. For the single beam echo sounders, new features for deep water mapping are described, as well as the possibility for combining investigation of shallow areas with side scan sonar and vertical echo sounding in the same instrument. Multibeam echo sounding technology for deep and shallow water is reviewed, and some new high resolution instruments using dynamic beam focusing is presented. The sediment profiling technology deals with a novel design for high resolution sub bottom profiling, based upon a Mills Cross transducer with resolution as good as 3 degree in its largest configuration and a frequency range of 2,5 ? 7 kHz. Remarkable features of the system are a very high ping rate even for deep water, and the capability to map buried objects or structures by several simultaneous beams. Some results obtained with the first installation on the French research vessel ?Beatemps Beaupré? are presented.

Jan 1, 2003

By Igor E. Mikhaltsev

The goal of investigation of the midwaters and of the bottom of the world - ocean versus technological possibilities. Manned vehicles and maximum depth decision. The methods of solving of the problem. The science and technology alloy. Mutual venture of Academy of Sciences of the USSR and, Rauma-Repola Oy of Finland. MIR-1 and MIR-2 - as twins. No reasons of copy "Sea Cliff" and "Nautilus". Six landmarks of specificity of "MIR"-type submersibles. The manned spheres and three ballast spheres are made of maraging steel; the electric power resource (100 kwh) and maximum underwater speed (5 knots) is two times more than of the analogous vehicles while the batteries are of NiFe type; the MIR submersibles have the seawater ballast (and trim) system which means practically unlimited vertical manoeuvrability ; and the weight in air is equal to "Nautilus" - 18,6 tons (in case of equal energy resource the weight of MIR-1 or MIR-2 would be 17 tons). Some remarks on standard life support (248 man-hours) safety systems and specificity of launch & recovery system.

Jan 1, 1988

By Alister C. Skinner

The Marine Operations and Engineering section of the British Geological Survey based in Edinburgh, Scotland have, over the last 30 years, developed and operate a series of remotely operated, and powered, seabed coring systems. These systems were initially developed to provide a cost-effective solution to ground truth seismic reflection data for regional geological mapping, where the only solution that existed was conventional and expensive drill-ships. Since the early 1990?s these tools have been used for many other applications in industry and science. Currently the systems can operate in up to 2000 m water depth for 5m seabed penetration and up to 4500m water depth for a specialised oriented core drill which collects a scribed core to 0.8m below seabed. Scientific applications focus on determining the geology of an area and follows pre-determined geophysical interpretations. It usually also follows other coring attempts with non-powered coring equipment which is invariably unsuccessful if the strata is over-consolidated sediments or hard rock. Commercial applications include cable and pipeline route surveys, diamond, gold and base metal exploration, beach reclamation and aggregate materials evaluation. In many cases there is a blend of science and commercial investigation typified by coring in hydrothermal vent areas or carrying out geological coring in a frontier oilfield province. The versatility of the drills allows cost effective and rapid operations in remote and hostile areas where a rapid investigation may be the only one possible in a short weather window. The deepwater operational capability also allows science and commercial assay to be obtained ahead of potential exploitation and allows formulation of scientific theories or commercial project plans based on sound core data. Being mobile and compact these corers may be used from suitable (Dynamically Positioned or Anchored) vessels of convenience and thus provide a cost effective platform for sampling different types of seabed geology on an international basis.

Jan 1, 2004

By S. Rajendran

Gas Hydrates (Methane Hydrates) are solid, ice ? like substances composed of water and natural gas. They occur naturally in areas of the world where methane and water can combine at appropriate conditions of temperature and pressure and are found in the ocean bottom sediments and in some permafrost areas. Besides temperature and pressure, factors like bathymetry, sediment thickness, sedimentation rates, and total organic carbon content (TOC) also control gas hydrate formation in the sea. The stability of gas hydrates depends on the critical high pressure ? low temperature combination (0-17 bars, 0-25ºC), which in turn dependent on the mix of gases from which the mineral is formed. As the critical parameters can be altered by deposition, erosion or slumping of sediments, formation or melting of ice cover, rise and fall of sea level and sudden temperature changes induced by tectonic activities, current flows or volcanisms, the gas hydrates tend to be very unstable. It is becoming increasingly evident that naturally occurring gas hydrates are significant component of the shallow geosphere and are of societal concern in at least three major ways: as an energy resource, a geologic hazard and a major contributor for climatic changes.

Jan 1, 2010

By Ian B. Corbett

De Beers Marine Pty Ltd. (South Africa) (DEBMARINE), a wholly owned subsidiary of De Beers Consolidated Mines Ltd. specializes in the provision of contracting and consulting services for offshore diamond exploration, Mineral Resource Management and mining. Established in 1983, the company is strongly focused on driving and sustaining growth of the offshore diamond mining industry into the 21st century. DEBMARINE provides full Mineral Resource Management and produce almost half a million carats annually for the Namibian Diamond Corporation (Pty) Ltd. from their offshore mining licence. The company is also extensively involved in feasibility studies to establish new mining ventures and in the exploration of several offshore Prospecting Licence Areas for other clients. As a pioneer in this field, DEBMARINE remains highly focused on technological development. A specialized section, the Technical Development Business Unit, has been established. Through relationships with various technology leaders, this unit develops new sub-sea mining technology and delivers productivity innovations aimed at realizing maximized carat extraction. This talk provides a broad perspective on the development of the Namibian offshore deposits and examines the critical role played by high-resolution orebody characterization and high-confidence Mineral Resource development at De Beers Marine.

Jan 1, 1998

By Cheng Xiangzhou

The China's Pioneer area includes two parts. The topography in the western part is very different from that in the eastern one. The distribution of the manganese nodules in these two regions differs correspondingly China Ocean Mineral Resources Research and Development Association (COMRA) will take appropriate measures so that the next development will be adapted to the features of its potential minable area.

Jan 1, 1996

By L. B. Khershberg

Marginal seas of the Russian Far East constitute the northwestern segment of the Pacific underwater belt distinguished by distinct metallogenic specialization of shelf-extended ore-bearing magmatic complexes and associated polycyclic mineralization. The coastal part of this vast region is known to contain both multiple placer manifestations and deposits, and non-metalliferous minerals. The latter are sedimentary deposits, the products of weathering, which contain re-deposited placer minerals in industrial concentrations developed on the shelf by certain geological processes. The shelf part of the Far Eastern seas is a seawater-filled continental margin. Complex geophysical mapping and drilling from ships of shelf sedimentary thickness and foundation has revealed the units of contemporary and ancient relief accompanied by formation of industrial concentrations of placer gold, cassiterite, titanium-magnetite, zircon, monzonite, and other components at different stages of placer formation. According to the information collected by prospecting by ?Dalmorgeologia? Co. Ltd. and other companies, placer-host structures within trans-placer-concentrating structures (land-shelf) are: shelf-extended river plains, contemporary and ancient shorelines, beaches, drained areas, spits, bars, detritus deficit zones, and terraces and bodies accumulated underwater in the areas where along-shoreline flows unload their detritus. They all could be used as criteria/signs for mapping and targets for placer prospecting.

Jan 1, 2004

By Mark D. Hannington

Results of the R/V Sonne Cruise (Edison) to the Tabar-Feni Arc from March 11 to April 5, 1994, a joint German-Canadian research cruise aboard the vessel R/V Sonne, undertook detailed mapping of the Tabar-Feni island chain, Papua New Guinea. The Tabar-Feni chain is host to several large porphyry stocks and epithermal gold deposits, including the giant Ladolam gold deposit on the island of Lihir (minimum 19 million oz. Au). The principal objective of the cruise was to map the seafloor in the vicinity of recently active alkaline volcanic islands in the Tabar-Feni chain and to characterize the tectonic setting of large high-level porphyry and epithermal gold deposits in the region. Additional work was carried out on shallow-water hot springs associated with mineralized geothermal systems on the volcanic islands. Complete sets of 1:50,000 scale (20-m contour) maps of the seafloor were produced for each of the four island groups (Feni, Tanga, Lihir, Tabar). The Lihir group was the most active and the most interesting. At least 4 (and probably 6 or 7), previously unknown volcanic cones were discovered within about 10 miles south of Lihir. The volcanoes are clearly very young and appear to have erupted along extensional faults produced by regional plate rotation. This recent volcanic activity appears to reflect recent forearc extension and represents the southward propagation of volcanic activity towards New Ireland. One volcanic cone at 1,490 m water depth is hydrothermally active, with very large areas of diffuse venting (100-200 m across), densely populated by beds of giant clams (probably calyptogena). Other vent-specific fauna are also present, including crabs, snails, sulfide worms, scale worms, limpettes, etc. The clam beds sit on a crust of hydrothermally baked and indurated, sulfidic, hyaloclastite-rich muds. The mineralization consists mainly of fine-grained disseminated pyrite and amorphous Fe-sulfides. A second, much larger cone at a depth of 1,070 m is capped by massive vesicular lavas which are intensely fractured and mineralized. Abundant sulfides and amorphous silica occur in stockwork-like veins which

Jan 1, 1994

The chemical composition of the nodules varies with the type of manganese minerals and the size and characteristics of their nucleus, but those who have an economic interest have the following composition: Mn 29%, Fe 6% Si 5%, Al 3%, Ni 1.4%, Cu 1.3%, Co 0.25%, Na 1.5%, Ca 1.5%, Mg 0.5%, K 0.5%, Ti 0.2 0.2% and Ba 0.2% (Morgan, 2000; ISA, 2002). The Pacific Rim is an area of abundant occurrence of polymetallic nodules (Glasby et al., 1980; Morgan, 2000). According to these authors, the Pacific sea floor of the Clarion-Clipperton Zone (CCZ) is one of the most interesting areas in regard to the genesis of polymetallic nodules. Their abundance in the ocean floor is very variable, as there are places where they cover more than 70% of the ocean floor. The nodules can be found at any depth, but the highest concentrations are between 4000 and 6000m (Morgan et al., 1993). In studies conducted in the EEZ of the Mexican Pacific are those made within the project "Research on the origin, process and distribution of minerals in the Pacific ocean floor in the Exclusive Economic Zone of Mexico". Within this project Rosales (1989) conducted studies on the origin, process and distribution of polymetallic nodules, finding that a number of processes give origin to nodules, being diagenesis one of the main mechanisms of elements that contribute to the nodules. Besides hydrothermal processes that are carried near the East Pacific Rise at 21° N, inputs are contributing to the nodules metallic elements and sediments, especially in regions close to the dorsal, as a greater influence hydrogenetic processes occurs westward (Rosales and Carranza, 1990). In 1993, after cruise MIMAR II, Carranza and Rosales refer that metals such as Cu, Co, Ni, Sn, Fe, Mg, Pb, Zn and Ba may have a relationship with the East Pacific hydrothermal activity and sea currents carry these metals in solution to the Clarion-Clipperton fracture area, where there are hydrogenic metals sources (Al, Fe and Mn).

Jan 1, 2011

By Andrea Koschinsky, Luise Heinrich, Stefan Gößling-Reisemann

"Germany, like several other countries, has entered a contract with the International Seabed Authority (ISA) to explore the prospects of commercial manganese nodule mining in the Clarion-Clipperton Zone (CCZ). Ensuring a maximally sustainable deep-sea mining operation requires a thorough understanding of the environmental impacts associated with every step of the mining process from the extraction of the nodules at the seafloor to the refinery on land. Against this background, the project presented here applies a combination of scenario-building and life cycle assessment (LCA) to assess and evaluate the sustainability performance of the individual process steps as well as the entire mining operation.Life cycle assessment (LCA) is a comprehensive methodological framework that allows the identification and quantification of impacts occurring during a products life-cycle, as well as the analysis and evaluation of their contribution to pre-defined impact categories, such as climate change, acidification and toxicity (Rebitzer et al., 2004). Until now, LCAs with a focus on raw material extraction have almost exclusively been applied to terrestrial processes. Noteworthy exceptions are offshore drilling, offshore wind farms and ocean fishing. Hence, the first part of the project is to investigate in how far LCA can be applied to deep-sea settings and if and in what way it could be adapted to be used in a deep-sea mining context."

Jan 1, 2017

By Alexander Malahoff

A shipboard research system capable of operating in waters of up to 2,000 meters has been designed and implemented by the Hawai'i Undersea Research Laboratory (HURL) of the University of Hawai'i. It uses a remotely-operated ocean bottom survey camera system, an ROV, the Pisces V submersible, and a submersible emergency recovery system, all aboard the 222- foot R/V Ka'imikai-o-Kanaloa. All systems are operated from the stern of Ka'imikai with a mounted Caley telearm and articulated A-frame system. The system was designed for multipurpose use of the ship for launch and recovery of the Pisces V submersible on a lift recovery line (with or without diver assistance), or night-time operations with an electro-optical cable using either the HURL ocean floor sidescan or photo and video system operated at 10 meters above the ocean floor. The 1.14-inch diameter cable is also used to operate an ROV system. The garage/ROV system can also act as a submersible rescue system with a submersible lift capability. The ship is equipped with a SeaBeam and shallow penetration sediment profiling systems. This integrated system approach to deep ocean floor research will make it possible for HURL to carry out research pro- grams on seamount ocean resources and ocean chemistry and climate in Hawai'i and the equatorial Pacific.

Jan 1, 1995

By Steven D. Scott

The 1991 PACMANUS Expedition (Papua New Guinea-Australia-Canada in the Manus Basin) discovered a very large (approximately 800 x 350 m) actively-forming seafloor polymetallic sulfide 4 deposit in felsic volcanic rocks of the southeastern part of Manus Basin, a 60 km wide extensional zone of basalt, andesite and dacite volcanism in the New Britain back arc. The apparent neo-volcanic zone is a 30-km long, high standing, Y-shaped edifice, which we have named Pual Ridge ("Pual" means "fork" in a local PNG dialect). The PACMANUS deposit was found by deep-tow video on Pual Ridge along the flank and adjacent valley of a dacite lava dome. Videos show large spires, chimneys and mounds with abundant fauna. Only two small samples from an active chimney were recovered. Their mineralogy is a high temperature assemblage of chalcopyrite, bornite, tennantite, sphalerite or wurtzite and anhydrite. The bornite and tennantite and silver rich. Gold values for the two samples are 2 and 10 ppm. A pronounced methane and particulate plume was traced in the water column for 14 km to the northeast of the PACMANUS deposit. Other deposits of unknown size are nearby. The deposits of Pual Ridge and their surrounding volcanic rocks have close similarities to ancient massive sulfides of Archean to Phanerozoic age in Canada and Australia.

Jan 1, 2011

By Curtis Clement

Williamson & Associates, Inc. has developed a marine mineral exploration tool using an induced polarization technology (IP) under license from the US Geological Survey. Developed by Jeff Wynn at the USGS, this method has gone through several prototyping stages and is now in commercial use to map offshore ilmenite deposits. Preliminary results of a recent resource mapping program are discussed as well as potential applications in the detection and quantification of other minerals in marine sediments.

By S. Rajendran

The western continental margin comprises of the southwest coast (Cape Comorin-Mangalore), centralwest coast or Konkan coast (Mangalore-Bombay), northwest coast (Bombay-Gulf of Kutch) and the Laccadives area. Placer deposits of heavy minerals occur in discontinuous patches on the beaches along many parts of the west coast. The richest offshore placer deposits occur along the 25 km stretch of the southwest coast from Neendakara to Kayamkulam. The National Institute of Oceanography (NIO) surveys show that the sediments off the Konkan coast consist largely of silty sand, sandy silt and clay and the concentration of ilmenite is higher than the onshore. The heavy mineral concentration ranges up to 90% and has mainly ilmenite and magnetite with minor quantities of apatite, rutile, zircon, kyanite etc. The heavy mineral sands extend below the clays to water depth down to 20 m. The heavy minerals sands vary in thickness from 2-10 m. Offshore placers can be mined by using wire-line, bucket ladder and hydraulic dredges. Wire-line, bucket ladder and hydraulic dredges. Wire-line dredges may employ drag buckets or clamshell and hydraulic dredges suction or airlift principles. The dredges can be located on flat bottom or catamaran barges. Dredging of very near shore placers may be achieved by operating from land. The bucket ladder type of dredger has greater digging ability and hence can be deployed for mining placers which are partly consolidated or cemented or where the most valuable part of the deposit lies at the contact between the alluvium and the bedrock. This type operates very economically up to 45 m depth and needs minimum power requirement per unit dredged. Suction type hydraulic dredges can be operated very effectively up to 60 m water depths. This system is quite ideal for the inner shelf. The maximum practical economic working water depths for wire-line dredges are about 150 m. With the drag bucket modified into large net buckets, the method can be utilized to greater depths. They can be used in areas of high water currents and swells. The type of bucket can be changed readily with change in the nature of alluvium or substratum. The hydraulic suction dredge is the most suitable system for mining unconsolidated sediments. When the sediments are semi-unconsolidated, a cutter head can be mounted on the lower end of the suction pipe to agitate the seabed.

Jan 1, 1996

By Wilhelm Schwarz

Manganese nodules lay in vast areas of the deep sea floor. Ideal harvesting conditions for a manganese nodule field are dense nodule abundances of nodules between 20 and 60 mm diameter and a metal content as high as possible. With regard to the development of collector technology, the properties of the deep sea soil, in which the nodules are embedded and to which the nodules stick, are of major interest. The forces for loosening the nodules have to be provided by the collector. For this purpose water jets and/or mechanical devices can be employed. For the choice of the best collecting procedure, various criteria, such as collecting rate, energy consumption and the environmental impact on the eco system of the deep sea floor, have to be considered and weighted as to their importance. Nowadays, the concept of a mining system with a flexible transport hose and a self propelled collecting machine is increasingly accepted among the expert community. With regard to the trafficability of the deep sea soil with a self propelled mining machine, the mechanic properties of the soil and the morphology of the deep sea floor are of special importance. The manganese nodule fields, which are interesting with regard to their recoverability, are mostly in the areas of tectonic fracture zones, at which the morphology of the sea floor is formed by vulcanic activities. In these areas, deep sea mountains, pits and other obstacles exist that have to be driven around if not trafficable.

Jan 1, 2003

By Det Juridiske Fakultet, Maria Madalena das Neves

The ocean is increasingly seen as the answer for a myriad of challenges facing humankind. In effect, in addition to being vital for transportation and communication, the oceans contain living and non-living resources that are essential to meet the demand for food, and to the development of pharmaceutical products, energy resources, and high-technology products. This entails that the oceans are under pressure by different activities: navigation, fishing, oil and gas exploration and production, renewable energy development, laying of cables and pipelines, marine scientific research, bioprospecting, and deep-sea mining for minerals and metals. The growing demand for essential minerals and metals such as cobalt, nickel, zinc, copper, and manganese, seen in tandem with technological advances in deep-sea mining, makes the latter an increasingly attractive activity, both in areas within and beyond national jurisdiction. At the same time, the further development of deep-sea mining adds to the problem of the competing uses of maritime space and accentuates the need to balance and articulate the interests of the different users of the seas (States, sponsored deep-sea mining investors, oil and gas investors, fishermen, shippers, etc.). Furthermore, as deep-sea mining activities increase and move on to an exploitation phase so does the possibility of new disputes (for instance during deep-sea mining exploitation a communication’s cable is severed, a vessel conducting deep-sea bottom fisheries damages deep-sea mining equipment, etc.).

Jan 1, 2018

By Thomas Pichler

In the past marine mining technology has focused on bulk mining of base metals from polymetallic massive sulfides. This has not been very successful because of the relatively low unit value of these metals and other reasons such as water depth, etc.. The process of gold enrichment in hydrothermal deposits is controlled through five different factors: (1) nature and source of the solution, (2) source of the gold, (3) a mechanism for mobilizing and transporting, (4) a mechanism for deposition, and (5) a mechanism to preserve the deposit. Gold has been identified in marine polymetallic massive sulfides from various locations on the ocean floor (e.g., spreading centers, seamounts) with contents ranging up to 5 ppm Au. This is within the current range of 1.0 to 7.0 ppm gold content which classifies gold ores. The gold appears to have been derived during hydrothermal alteration of the oceanic crust. Until the present there has been little attention to the possibility of mining gold or other precious metals in the marine environment. However, the magnitude of hydrothermal alteration (seawater can penetrates to a depth of 5 km into the oceanic crust) and primary gold contents of the rocks in the pathway of the fluid indicates that major gold deposits must have formed on or in the ocean floor, but they have not been found. To find a big deposit might only take an exploration model exclusively designed for gold exploration on the ocean floor.

Jan 1, 1993

By W. C. Burnett

The land phosphate deposits of the U.S. southeastern coastal plain have long been a major factor in the world trade of phosphate rock (Fig. 1). As recently as 1979, deposits of North Carolina and Florida alone accounted for about 33 percent of the entire world's phosphate exports. This situation is changing, however. World production increased by ~9 %, yet the U.S. share was down to ~28% in 1984. A complex interaction of economic and political factors combined with increasing costs of raw materials, production, and transportation have led to this systematic erosion of the U.S. market share. Changing land-use patterns within the southeast, environmental pressures, exhaustion of shallow high-grade resources in Central Florida, and the increased pressure from expanding low-cost production in other countries throughout the world account for much of the present difficulty in the U.S. phosphate industry. Considering this depressed environment -- what are the prospects for development of offshore resources? A summary of new research on offshore phosphorite within the U.S. Exclusive Economic. Zone (EEZ), as well as an attempt to place possible development of these resources within the current economic setting, is the purpose of this presentation. We will emphasize work in progress on a major offshore deposit along the U.S. Atlantic Margin as well as new research on Pacific Ocean occurrences of phosphorite on seamounts and insular slopes within U.S. waters.

Jan 1, 1986

By Roy Nilsen, Aravinda Perera

With the exponential growth of demand for minerals and need for diversification of supply channels, deep-sea mining is rapidly becoming inevitable. Productivity of underwater mining technology is salient to justify the deep-sea explorations. Methods for enhanced productivity of mobile mining equipment in a system level are investigated in this paper. Lessons learnt from the land-based mining has been the basis of this investigation. In general, mining productivity can be enhanced in two ways; firstly, by maximizing the amount of recovered material per unit time and secondly, by minimizing the cost of operation per unit material. Equipment that enable faster excavation, loading and transport in the seabed contributes significantly in increasing the amount of slurry per unit time. Improved mean time between failures (MTBF) of mining equipment will reduce the operational down time, thereby, contribute to maximize the amount of mined material per unit time. Several factors influence the operational cost minimization per ton of slurry. Higher efficient motor drive systems including the motor and PWM-fed inverter not only will save power but also will emit lesser heat thus the heat management can be less complex. This leads to more compact drive systems that allows higher power density, thus increased payload weight per empty vehicle weight. An energy storage method in the form of an utracapacitor in the electric drive system will also save the energy supply from the upstream.

Jan 1, 2018

By Stanley R. Riggs

Phosphate deposits on the southeastern U.S. coastal plain have long been the major force in world phosphate markets. World markets continue to grow, but the role of U.S. resources is rapidly declining. This situation results from a complex interaction of economic, political, and environmental factors. Causes for this ongoing erosion of the U. S. market include 1) escalating costs, 2) changes in land-use patterns, 3) environmental pressures oh conventional mining techniques; 4) exhaustion of shallow, high-grade resources in Florida, and 5) increased, low-cost production in other countries throughout the world. In fact, some agencies and commodity personnel predict that the U.S. will become a net phosphate importer early in the next century. If this projection is correct, the U.S. industry must look towards major changes in the near future in order to continue to compete in the world market. One possible change includes development and application of unconventional mining techniques to cheaply recover vast 'new' potential resources in areas with lower land-use pressures. These 'new' resources include 1) deep phosphorites within major sediment basins of the southeastern coastal plain and 2) subsurface phosphorites on the continental shelf and within the U.S. EEZ. These latter resources include extensive deposits in Onslow Bay, N.C.; broad regions offshore of Savannah, Ga. and Cape Canaveral, Fla.; and the central portion of the west Florida shelf. Little research and exploration has been

Jan 1, 1988