Search Documents

By Erwin Stötzer, Renato Fiorotto, Wolfgang G. Brunner, Manfred Schöpf

"Deep mixing methods can be used economically for the construction of cut-off or excavation support walls where other systems such as traditional soldier beams and lagging walls would yie ld unsatisfactory performance, where the installation of vibrated or driven sheet piles could cause vibration induced settlements and where concrete diaphragm walls would be time consuming and expensive. The new CSM method can largely replace the more conventional single or multiple auger methods of soil mixing or jet grouting. The cutter tool is similar to a cutter used in diaphragm walls or cut-off walls and is operated with a Kelly mounted on a drill rig. With this system much deeper walls can be installed and even hard soil layers can be penetrated. CONVENTIONAL SOIL MIXINGIn 1962 Norman Liver patented an auger-based soil mixing technique that has become the basis for the world's current technology.The deep mixing method (DMM), as it is known today, is an in situ soil treatment and improvement technology where the soil is blended with binders and/or other materials that are introduced in a slurry or dry form.Typically one or more hollow, rotating mixing shafts tipped with some type of cutting tool are mounted vertically to the mast of a base carrier and are driven into the ground by hydraulic or electrically powered rotary heads. The shafts above the cutting tool may be further equipped with discontinuous auger flights and/or mixing paddles. The binder is injected through the hollow shafts to nozzles located near the cutting tool where it is mixed with the ground to form columns of treated soil.Individual column diameters range from 0,6m to 1,5m and may extend to 40 m in depth. They can be arranged individually or in contiguous or secant patterns to produce a wide range of treated soil structures on both land and marine projects. Typical configurations are: Single elements, rows of overlapping (secant) elements, grids, lattices and blocks (Fig. 1 )."

Jan 1, 2005

By Renzo D. Verastegui, T. C. Michael Law, Sitotaw Y. Fantaye, Alfredas Daugiala

"When completed, 520 Park Avenue will amend the Manhattan skyline and be one of the most prestigious high rise towers in New York City. The 52-story condominium building is located on a 60 by 100 feet lot on East 60th Street between Park and Madison Avenues. The geographically complex site is bounded by two fragile 5-story masonry buildings on the east and west, a mid-rise building on the north, and a New York City subway tunnel on the south. To add to this complexity, the ambitious development required 70 to 80 feet of excavation, mostly below groundwater level in highly permeable rock, to accommodate four levels of cellars. The new building also cantilevers 24 feet over a five-story historic building on the east. The limited footprint of the building coupled with large compressive and tensile axial loads, considerable base shear and over-turning moments, and the required deep excavation, presented unique foundation challenges. This paper describes how the challenges were solved with an innovative combination of permanent secant pile walls and drilled shafts.INTRODUCTIONThe project site is located at 45 East 60th Street, on the block bounded by East 61st Street to the north, East 60th Street to the south, Park Avenue to the east, and Madison Avenue to the west. As shown in Fig. 1, the site is surrounded on three sides by buildings sensitive to differential settlement. In addition, a NYCT underground subway structure lies below East 60th Street approximately 13 feet south of the site. The base of the subway structure is approximately 42 feet below the street.The project consisted of constructing a 52-story tall building. A portion of the superstructure cantilevers 24 feet over an adjacent five-story historic building. The underground construction for the new building involved a four-level basement, extending about 60 feet below ground surface. The excavation subgrade is much deeper than both the subway structure and the adjacent shallowly-founded building foundations."

Jan 1, 2016

By Stuart Coutts

"This paper presents an overview of the author’s experience related to the assessment of the base capacity of straight shafted and enlarged-base bored piles in sand. A design approach based on CPT qc is described which has been calibrated using a database of load tests. The importance of correct installation techniques with instrumentation are illustrated and a discussion is presented on the current use of high strain dynamic testing to validate compliance with design. An example of a recent project with high quality instrumented load test data illustrates the close match to the proposed best practice approach and also highlights the importance for consideration of the effects of stress relief for deep foundations installed in deep excavations.1 INTRODUCTIONContinuous Flight Auger (CFA) piles are the bored foundation pile of choice for sand deposits across Australia. The evolution of the determination of the base resistance of CFA piles has been shaped by available investigative techniques, calculation methods, and calibration of designs with laboratory and field testing. The Cone Penetration Test (CPT) has been widely used in Western Australia (WA) where the test has been commercially available via multiple contractors for more than 25 years. On the East coast, the adoption of CPT testing has been slower with a transition from traditional Standard Penetration Testing (SPT) still occurring. Dynamic pile load tests are often used to derive parameters. The influence of pile installation on performance is commonly misunderstood and is an important element on any discussion of pile capacity for CFA pile types. The interface between the base of the constructed pile and the in-situ soil has an influence on capacity such that a poorly constructed pile base will have limited (if any) contribution to pile performance within the normal working range, generally within a 10 mm movement. The research presented in this paper pertains to CFA piles (no drilling fluids) and enlarged base piles constructed using CFA techniques under drilling fluids such that clean pile/base interface is targeted. Developments in modern piling equipment and instrumentation allow the pressure and volume of delivered concrete/grout to piles to be accurately monitored at various stages of installation such that repeatable ‘best practice’ can be achieved. The changes in soil conditions that occur due to the disturbance of the install technique are also important.Although the results of this research are likely applicable to bored piles, the interface between the pile and in-situ soil (shaft and base) need to be considered for various installation techniques. The effects of stress relaxation (due to removal of soil above pile base and adjacent shaft), time to concreting, and the zone of disturbed soil around the pile shaft are paramount.2 INSTALLATION CONSIDERATIONS The pile mix (concrete/grout) and interface with the in-situ soil are also an important consideration. For example, coarse grained, poorly graded, dry, clean sand will be partially permeated by most pile mixes; such that the influenced soil will be enhanced and in instances the overall effective pile dimensions increased. Permeation of the disturbed zone of a pile or anchor shaft along with scale effects (Lehane 2009) can have significant effect on shaft capacity and shaft frictions significantly exceeding expected are not uncommon based on ‘theoretical’ dimensions. Advancements in mix technology and mix techniques also have a large influence on the pile/soil interface. The ability of the piling rig and augers to excavate a plumb and gauge hole can also have a large influence on the zone of soil disturbed adjacent the constructed pile with a resulting influence on capacity."

Jan 1, 1900

By R. Lee Wooten, David R. Shields, Darren D. Clark

"Borehole permeability tests that measure flow or head changes in boreholes located within seepage barrier walls are commonly used to estimate the in situ permeabilities of those walls for quality control and assurance. The current state of practice for estimating permeabilities from these barrier wall borehole tests is to use equations published by M. J. Hvorslev in 1951. Hvorslev’s borehole test equations model an infinite stratum of uniform permeability, which is not the actual condition for a test performed in a low permeability barrier wall located within a high permeability stratum. We examine and develop alternative equations based on line source analytical models, which more closely match barrier wall test conditions. We describe how these alternate equations can be used to estimate barrier wall permeabilities from borehole tests and compare the results to those obtained from the Hvorslev models. We also provide recommendations that consider differing upstream and downstream water levels.Barrier Wall Permeability Tests - State Of PracticeThe installation of seepage barrier walls has become more common in a variety of applications ranging from dams and levees to contaminated sites requiring retardation of groundwater flow. The types of seepage barrier walls and installation methods include soil-bentonite, soil-cement-bentonite, concrete, self-hardening slurry, geomembranes, and sheet piles, installed with various soil mixing, slurry-supported trench, and driving methods.Owners and contractors have used a variety of methods to evaluate the permeability of these seepage barriers. The following table lists commonly used quality control/assurance tests for evaluating the permeability of a seepage barrier."

Jan 1, 2016

By Sumantra Sengupta

"Northeast Frontier Railway (NF Railway) intends to connect Imphal, the capital of Manipur (bordering Myanmar) with Assam by railway link. They have planned a 125km long railway line that passes through steep rolling hills of Patkai region, eastern trail of Himalaya, and as a result large number of tunnels and bridges need to be designed. While the high mountains are penetrated by tunnel, the deep gorges between the mountain ridges are connected by tall bridges. The tallest of such bridges connects a gorge at about 140m above its bed level with an overall length about 700m at rail level. In all, five such bridges with tall piers are now under construction. With extensive study on possible alternate arrangement of the bridges considering the effect of high seismicity of the area, moderately to highly weathered siltstone/ sandstone as ground bed material, slope of the hills etc it was decided that bridge will be founded on 1.5m diameter bored cast in situ piles with length varying from 20m to 30m depending on the location. The substructures are RCC hollow pier and superstructures are steel open web through type girder of 103.5m span. Considering absence of any major construction work in the vicinity, it was decided that prior to design work, Site-specific spectrum study will be carried out and design will be carried out considering the varying stiffness of the tall piers, each of different height. Interesting results were obtained regarding behavior of piles under lateral loads generated by high seismic conditions. The paper discusses in detail the design of Pile foundations and the effect of bed material along the steep slope on which the piles are being constructed.INTRODUCTIONIndian Railway has undertaken the construction work of connecting the North-Eastern states of India through railway line. The major stretches of the area passes through hilly terrain and as a result the line passes through tunnels and bridges in succession. The tall mountains are being penetrated with tunnels and immediate after deep gorges are crossed with high level bridges. The entire area is under high seismically active zone. The bed material below the ground level of the sloped hill is 4 to 10 meter of mixed soil of sand, gravel, pebbles etc underlain by moderately to highly weathered sandstone, siltstone at the higher level and moderately weathered sandstone, siltstone at lower level. Considering all the aspects like constructability, maintainability, geological and geotechnical aspect, seismicity, stability, safety, functional aspect and cost it was finally decided that the bridges will be simply supported structure with open web through type steel superstructure of maximum span 103.5m and hollow cylindrical discretely varying RCC substructure with 1.5m diameter group of piles as foundation. The paper discusses on the design aspect of the pile foundation in the rocky strata in the hill slope. The codes and standards that have been followed for design are IRS (Indian Railway Standard), IS (Indian Standard), IRC (Indian Road Congress), AREMA (American Railway Engineering and Maintenance-of-way Association), UIC (International Union of Railway) provisions."

Jan 1, 2015

By C. Dai, S Raathiv

The Waikato Expressway is one of the New Zealand Transport Agency’s (NZTA) seven roads of National Significance. Coffey is part of the City Edge Alliance engaged by NZTA for the Hamilton Section of the project. The 22km Hamilton Section is the largest and most geotechnically complex section of the Expressway. The Mangaonua gully in Sector 6 is the most challenging geotechnical area of the project for piling works. Together Coffey and Brian Perry Civil have carried out the temporary and permanent design and construction of embankments, piling works, retaining walls and soil improvement works for the bridge construction. The design and construction works were governed by weak alluvial layers and artesian pressure layers several meters beneath the ground level. This paper presents the action taken to improve the foundation of temporary platform, control the artesian pressure, prevent bentonite leakages into the highly permeable alluvial layer and challenges in the base grouting process. This paper summarises the key components in the construction and supervision of bored piling works and outlines innovative solutions for challenges which we faced during the construction.

Nov 1, 2022

By R. Gerritsen, Erwin de Jong, E. van der Velde, C. te Boekhorst

"In recent years the market for Mixed-In-Place soil mix techniques in the Netherlands has been growing rapidly. Initially the technique was used to create cut-off walls near river dikes and as a vibration free method to create retaining walls for building pits. Studies have been undertaken and projects are executed in order to strengthen the dike itself by the use of Mixed-In-Place techniques. In February 2012 Bauer Funderingstechniek started the construction of the first polder in the Netherlands with their approved Mixed-In-Place cut-off walls. This article explains the background of the use of this cost-effective and durable construction method and discusses how the challenging requirements from the client were fulfilled, both in design and execution. The quality assurance and quality control consisted of preliminary soil and mixture investigations, extensive measurements during construction and leakage detection through geophysical methods. The information is presented in 3 case histories, all subprojects of a large infrastructural project ‘Leeuwarden Vrij-Baan’ in the Netherlands.INTRODUCTIONThe Netherlands have a worldwide reputation in creating their own country by reclaiming land from the sea. Since the 15th century the Dutch have been creating “polders”, areas of reclaimed land below sea level, surrounded by dykes and with a mechanically maintained water level. In the 20th century the use of artificial polders became an interesting construction method for creating underpasses below motorways and canals using watertight geomembranes to create an impermeable layer that separated the polder from its surroundings. These kinds of structures have one big disadvantage, they need a lot of space. The main idea of such a structure is that the upward water pressure under the geomembrane has to be in balance with the remaining soil on top of it. For this reason, the geomembrane has to be placed at a depth significantly deeper than the polder surface, depending on the hydraulic head in the aquifer. Slopes of 1:3 (1 vertical : 3 horizontal) are most commonly used, resulting in very large open excavations and massive earthworks, even for relatively small underpasses. Special measures can be taken to reduce the spatial use with vertical limits, but these measures will increase the building costs (Gerritsen et al. 2014)."

Jan 1, 2015

By Remco Offenberg, Marcel Bielefeld, Martijn van Delft

The question of the continued suitability of existing foundations arises when the function of the superstructure changes. This can occur when the superstructure is replaced or when the existing structure is expanded, leading to higher loads on the existing foundation. Quite often it is a challenge to define the suitability (with respect to integrity, bearing capacity or both). The lack of information on the existing foundation (such as pile dimensions, installation records, original soil investigation, design calculations, etc.) makes it frequently seemingly impossible to assess whether the foundation or foundation elements can be re-used. The paper outlines the tools available to an engineer to evaluate existing foundation piles for potential re-use. The paper illustrates the application of these tools through a few case studies from The Netherlands, including the evaluation of a 400 years old bridge foundation to address increasing traffic loads.

May 1, 2022

By Jie-qun Zhai, Jian Jia, Ke Yang, Xiao-lin Xie, Yu Zhang

"With cities’ development, underground space exploitation presents a need for bigger and deeper constructions now. Technical problems founded during the construction of deep foundation pit support become more and more important. The supporting system has to cut or partly cut off hydraulic connection outside and inside the foundation pit, control the ground settlement caused by dewatering and make sure safety of foundation pit and its surroundings. Some preliminary study and application of ultra-deep soil reinforcement methods have been conducted in Shanghai’s deep excavation engineering. On the basis of engineering practice of ultra-deep foundation pit in Shanghai, some field and laboratory test, this paper analyzes effects of different ultra-deep soil reinforcement methods and their influence characteristics of surrounding environment. It also summarizes these methods’ sealing effect, construction and economic efficiency and concludes their characteristicsINSTRUCTIONShanghai is formed from marine sedimentation. In Shanghai, from earth’s surface to 30~40m underground, soil is mainly consist of soft clay with 40% moisture content. There are also many thin silty-sand layers in the earth, so the soil is both soft and permeable. Under 40m, soil is mainly thick silty-sand layers and fine-sand layers with medium density and confined groundwater whose water head is about 7m high.With the rapid development of Shanghai’s municipal construction and high-rise buildings in the recently ten years, the number of underground structure including subway station, tunnel and high-rise building basement are constructed rapidly. Due to the permeability and softness of Shanghai’s soil, it is necessary to reinforce soil to make sure the safety and high construction rate of engineering project in Shanghai.Because of deeper excavation depth and bigger excavation area in Shanghai, ultra-deep soil reinforcement is used preliminarily in Shanghai. Combining with engineering practice of ultra-deep foundation pit in Shanghai and employing field and laboratory test, this paper analyzes effectiveness of different ultra-deep soil reinforcement methods and concludes these methods’ characteristics and their applicability. All this can guide further application of these methods."

Jan 1, 2015

By Fredrik Sarvell, Harald. Ihler, Veli-Matti Uotinen, Jukka Rantala

"Many of the valid international building codes state that the lateral support provided by the soil is sufficient to prevent buckling of fully embedded piles. However, the development of small diameter micropiles and especially the use of high strength steel have evolved to applications including high capacity elements. The ultimate structural load bearing capacity of a pile in a cohesive soil is decided by examining which gives the lowest value, the peak buckling load and the resisting moment provided by the surrounding soil medium or the structural capacity of the pile cross section. In both cases, the initial deflection of the pile is a significant factor when the axial load bearing capacity of the pile is determined. Steel micropiles are joined commonly with mechanical splices. A less rigid mechanical splice is often a weaker hinge that allows the pile to bend and deflect more during installation increasing the initial deflection of a pile. In addition the less rigid splice element decreases the bending capacity of a jointed pile section and the ultimate axial load capacity of the entire pile. A series of FE analysis performed for various pile sizes suggest that the steel pipe piles including separate pile sections and mechanical splicing elements should have the combined bending stiffness of EIshaft = 0,75 × EIpile. This requirement yields to the buckling resistance of at least 96 % of the solid reference pile with the sameinitial eccentricity in similar soil conditions.IntroductionMany of the valid international building codes state that the lateral support provided by the soil is sufficient to prevent buckling of fully embedded piles. However, the development of small diameter micropiles and especially the use of high strength steel have evolved to applications including high capacity elements. The potential buckling of these very slender high capacity piles in soft soils may in many cases be the controlling design factor of the pile, especially with end bearing micropiles.A typical sequence of soil strata in Nordic countries, such as Norway, Finland and Sweden, constitutes of friction soil or dry crust clay on top of soft clay followed by till. This soil stratum often rests on solid bedrock of granite or gneiss. Conditions like these are suitable for slender end bearing piles subjected to buckling and especially steel pipe piles where most of the material is located at the edge of the cross section. Other reasons for using slender steel pipe piles are for example fast installation with minimal waste, efficient manufacturing and relatively well established design and execution procedures. Minimum quality criteria’s regarding splices for steel pipe piles are recommended to be set as national provisions to ensure quality and comparable procurements in foundation business."

Jan 1, 2014

By Terence Ma, Seok hyeon Chai, Jeff Lam, Thamer Yacoub, Brigid Cami, Sina Javankhoshdel

The Limit Equilibrium (LE) analysis of pile-supported geotechnical structures normally assumes a constant shear force for the pile instead of considering the non-linear capacity of the pile which is related to the pile displacement. In this study, a 3D Limit Equilibrium analysis is carried out for a landslide model supported with piles by considering the constant and non-linear capacity of the pile which is computed using a separate Finite Element (FE) algorithm. The depth of the pile, soil layering, and the pile properties are used with an assumed maximum displacement to compute the geotechnical non-linear capacity of the pile. In this study, the results of the initial unreinforced 3D LE model was first compared to the 3D FE analysis results. Then, the pile pattern was applied to the failure region in the 3D LE model, and then the factor of safety was recomputed. The results of the constant shear piles were compared to the model with the non-linear piles.

Sep 8, 2021

By Kalyani Devabhaktuni, Mike Minton, Mark T. Howe, Yan Zhang

During the procurement phase of a Design-Build (DB) project, design-build contractors must often commit to a fixed price based on limited or incomplete geotechnical information. This lack of information can result in an inaccurate assessment and allocation of project risk to either the contracting authority or the DB contractor. This paper presents a case study of an elevated water tank supported by mixed ground improvement techniques, including Vibro-Compaction (VC), Aggregate Piers (AP) and Compaction Grouting (CG) in East St. Louis, Illinois. An adaptive design and contracting approach provided the best value solution for a complicated set of geotechnical problems, including static bearing capacity and settlement concerns as well as liquefaction induced settlement. Close cooperation between the owner, the tank contractor, the geotechnical engineer and the ground improvement contractor was essential to produce an effective solution. Ground Improvement techniques resolved the geotechnical challenges at the site through adaptive design methods, utilizing progressive rounds of verification and real time data acquisition to achieve performance objectives. This paper details the evaluation of geotechnical criteria, the selection of ground improvement techniques, the adaptive design and implementation of ground improvements, as well as contracting methodologies used to ensure that the best value was provided. PROJECT INFORMATION In November, 2016, CB&I Storage Tank Solutions (McDermott) submitted a design/build proposal for an elevated water tank for Illinois American Water Company (IAW) in East St. Louis, Illinois. The purpose of this tank was to have backup water capacity for power generation. In the RFP, IAW requested two alternate styles of tank: Option 1, a 1250 Million Gallon (MG) Composite Elevated Tank or Option 2, a 1250 MG Waterspheroid tank. Option 1 consisted of a steel tank supported on a concrete tower. Option 2 consisted of a steel tank supported on a steel shaft. The height (determined by IAW) was 140 feet to the top capacity line measured from top of floor slab.

Jan 1, 2019

By Chu E. Ho

This paper reviews the design of jet grouting at re-entrant corners of excavations where the diaphragm wall and secant pile wall installation were interrupted by existing utilities in the streel sidewalk. Jet grout blocks were formed to seal the gaps in the walls for excavation support, consisting of four to six columns in clusters. Jet grouting was performed around an electrical duct bank which had to be maintained. Jet grouting was executed through stratified soils using various combinations of jetting parameters for different soil strata. The installation sequence and age of the neighboring columns within a cluster will affect the jet’s ability to form subsequent columns. When jet cutting is limited next to hardened grout columns or embedded obstructions (such as diaphragm walls or secant pile walls in this case), the specific gravity (SG) of spoils would be reduced and tend toward the value of the injected grout SG. The magnitude of spoil SG is also influenced by the variability of the grout mix supplied. Specific Gravity Ratio (SGR) defined as the ratio of spoil SG to the actual grout SG at the time of jetting can be used as an indicator of successful treatment, with SGR > 1.0 indicating effective soil erosion. Verification coring and testing were implemented to confirm target column diameter and strength of grouted soils have been achieved.

May 1, 2022

By Julie Clarke

In 1939 Dr. Ralph Peck criticized the Civil Engineering community for taking a bifurcated approach to the prediction of building damage due to subsurface geo-technical works. Specifically, he observed that Geotechnical Engineers concerned themselves only with subsurface issues implying that their results were largely independent of the presence and condition of the structures above. He continued that Structural Engineers charged with risk assessment of buildings approached their work nearly in isolation of below ground activities. Seventy years later, although the state-of-the-art has enabled a better understanding of soil-structure interaction, the reality remains that risk assessment from subsurface construction, is not yet an integrated activity when done on a large-scale basis. To help move beyond this, this paper proposes a new, integrated methodology for preliminary assessment that considers a three-stage process that involves the following: (1) traditional empirical relationships for predicting ground movement from tunneling, (2) recent advances in condition assessments, and (3) architectural designators related to usage and historic preservation listings. The methodology is applied to a study area of nearly 260 buildings in the city center of Dublin Ireland, in an area slated for an upcoming metro. The results are com-pared to the Environmental Impact Statement issued for the official project. Al-though the test case is for tunneling, the approach may be adapted to other subsurface construction activities including excavation and piling.

Jan 1, 2009

By Tai Luu, Michael McNicholas, James C. McIntyre

The Jersey City Municipal Utilities Authority (JCMUA), discovered that an existing sewer pipe had collapsed under the New Jersey Transit Conrail Railroad between Pine Street and Ash Street in Jersey City New Jersey. Immediate action was taken to abandon the pipe in place and install a new sanitary sewer. The borings showed 10-20 ft (3.04 m.- 6.09 m) of competent fill overlaying approximately 8 ft. (2.44 m.) of compressible peat and organics. Groundwater was at 8 ft (2.44 m) below ground level. The poor condition of the soils at subgrade could not withstand the extreme weight of the jacking machine or the thrust force required to push the casing from the launching pit to receiving pit. The support of excavation (SOE) would therefore not only need to retain the soil to allow the jacking equipment to reach subgrade at 14 ft (4.27m) below working grade, but also the back wall of the SOE would need to be sufficiently robust to function as the reaction block for jacking operations. The alignment and allowable tolerance for the jacked casing was minimal, therefore the performance of the SOE was extremely critical to the success of jacking operations. This paper will discuss in detail the design concepts that were developed and implemented by the team to overcome these obstacles. HISTORY The discovery of a collapsed section of an existing sanitary sewer led the Jersey City Municipal Utilities Authority to act on an emergency contract. The project design team was tasked with developing an abandonment plan for the broken pipe and installation of the new pipe through challenging geology. The new 180 ft.(54.96 m) long, 54-in. (1.37 m) . diameter sewer pipe was designed to be contained within a 72-in. (1.83 m) protective steel casing. The installation of the new sewer pipe would require a detailed understanding of the geology. The geotechnical subcontractor assembled a subsurface investigation report on November 2nd, 2017. It was quickly realized that the only way to replace the pipe was with a jacked pipe system since the large grade change and the Conrail Right of Way created no other alternative. Delaying or closing the railway was absolutely not an option as that particular railway served as the main heavy-haul route to and from Jersey City. It became apparent that a major obstacle to pipe jacking was the challenging geology present across and beneath the proposed sanitary sewer. The following challenges faced the design team prior to the installation of the replacement pipe:

Jan 1, 2019

By Achyut Kumar Allady, Praveen Arumughan

NCHRP Synthesis 418 (2011) entitled, “Developing Production Pile Driving Criteria from Test Pile Data” details the occurrence of dichotomy between pile Skin resistance and pile Tip resistance mobilizations at different times for different hammer blows during pile driving operations. With increasing usage of High Strain Dynamic Testing (HSDT) the engineering community started paying more attention to this occurrence of dichotomy resulting in overdriving, pile damage, increased claims, and loss of time. To overcome the dichotomy limitations of HSDT, NCHRP recommends, “the use of superposition to combine the back-calculated tip resistance from a blow on initial drive or from redrive with the back-calculated skin resistance from the early blows at the beginning of restrike”. However, the current practice of external mounted gauges and signal matching for a single blow are unable to evaluate independently the Skin resistance and Tip resistance to achieve the goal of determining the optimum Total Pile Capacity using the superposition. This paper discusses advancements of science and technology with sensors embedded at the pile top and pile tip, the data collected is analyzed by the state-of-the-art FDOT Method to determine Skin and Tip resistances independently for every blow. Independent Tip and Skin resistances each with a Resistance Factor can be summed up to obtain optimum Total Pile Capacity. Additional benefits of determining independent Skin and Tip resistances include obtaining lost skin capacity due to scour, due to pre-drilling/preforming and uplift tension capacity. Furthermore, the benefits of embedded sensors include increased quality control/quality assurance through 100% testing, accelerated construction, life cycle monitoring and asset management.

May 1, 2022

By Raymond J. Poletto

This paper describes the special problems that occur with the construction of diaphragm walls and discusses the lessons learned during the repairs of structural walls. Although diaphragm or slurry wall technology and equipment has vastly improved since its development in the late 1950?s, significant problems still occur. Key issues are repairs related to panel joints between wall panels, concrete defects associated with tremie concrete problems, leaks and other defects at tieback reservations or inserts, wall leaks within the plane of the wall and surface repairs. The paper supports the position that diaphragm walls are relatively watertight when properly constructed, but cautions that it is necessary to address potential problems in the design stage and allow for flexibility in construction so that the problems that occur can be corrected once encountered. Due to the fast track nature of most projects the time available for design, detailing and construction is limited. As a result, insufficient attention to detail by any of the responsible parties can lead to imperfections and defects in the wall. The authors describe the nature of these problems and their potential resolution based on ?lessons learned.? The timely response to wall problems is essential to the successful completion of a diaphragm wall project. Appropriate repairs have resulted in largely successful jobs starting with the World Trade Center in New York City. The authors? total 80 years of experience as the engineer of record and designer, inspector and contractor?s representative for the diaphragm wall results in a unique insight to deal with these problems.

Jan 1, 2011

By Alex Grenoble, Alex Reeb, George Filz, Farzad Abedzadeh

"This paper summarizes available information on the characteristics and properties of deep-mixed soilcement produced by the wet method. The topics covered in this paper include: unit weight, unconfined compressive strength, strength variability for field mixed materials, influence of curing time, influence of consolidation pressure, Young’s modulus, differences in strength and stiffness between small and large samples, creep deformations, Poisson’s ratio, and tensile strength. In addition, this paper discusses the development of design considerations and recommended property values for a project that uses soilcement to protect an existing dam penstock from loads applied by an overlying stability berm. Some of the key recommendations for the deep-mixed soil-cement to be used in this project are that (1) a curved strength envelope that includes tensile strength can be used in the analysis, (2) the stress-strain and strength properties can be characterized using Duncan and Chang's (1970) hyperbolic model, and (3) a specification based on the median unconfined compressive strength value is appropriate.INTRODUCTIONFor many projects, including foundation and embankment support, deep mixing can be designed based on simplified procedures and following standardized guidelines (e.g., FHWA 2013). However for unusually complex or critical projects, it is often necessary to perform numerical analyses, and in order to perform these numerical analyses well, a thorough understanding of the material properties is needed.This paper summarizes information on the characteristics and properties of deep-mixed soil-cement produced by the wet method, and it discusses the development of design considerations and recommended property values for a specific project, herein referred to as the penstock project, that requires numerical analyses. For the penstock project, a horseshoe-shaped enclosure of soil-cement is being considered beside and above an existing dam penstock to protect it from loads applied by an overlying stability berm that will be constructed for seismic remediation. The concept is to use soilcement created by the deep mixing method along the sides of the penstock and to use compacted soilcement above the deep mixing to create the crown of the protective soil-cement zone around the penstock. For this application, the soil-cement stiffness, rather than its strength, is the controlling design parameter. To achieve the necessary soil-cement stiffness, the strength will be high enough that the factor-of-safety values against instability along potential failure surfaces passing through the soil-cement are high. Following conventional practice, the soil-cement acceptance criteria will be based on the unconfined compressive strength, and the specified strength will be selected to produce the desired modulus value."

Jan 1, 2015

By David Sherwood

The paper has been prepared as the basis for the 2008 John Mitchell Memorial Lecture. It reviews major developments in ground engineering over the last 20 years, not from the point of view of technical processes, but from the drivers that have driven these developments and the needs that they have met. It concludes with a glimpse into the future and suggests to where current trends will probably lead us. By its nature such a review is closely aligned with personal experience and it relies heavily on case histories largely from within the writer?s own experience over that period.

Jan 1, 2008

By Akshay Sakhuja, M. S. Karthika, R. Vignesh

"The bridge across River Mandovi in Goa is a cable stay bridge structure proposed parallel, along existing bridges for regulation and reduction of vehicular traffic; the entire bridge structure is supported on pile foundation socketed in rock. This paper describes drilling related issue encountered during execution of pile where bed rock varies considerably from factual geotechnical investigation, which in turn affected the productivity of bored piles socketed in rock then chiseling is advocated for rock socketing with limited number of blows based on penetration resistance of rock encountered or equivalent energy principle to increase the productivity and also to avoid excess chiseling which otherwise would have fractured the rock mass below and around the pile tip resulting in increased settlement of pile subjected to design load. Contractor decision on socket length have been taken without compromising either quality or productivity; the paper presents various procedures and the equipment involved for installation of pile in rock along with the conclusion related to termination of pile in rock and also the lessons learned in process.INTRODUCTIONPile foundations are generally used to transfer heavy loads in deeper bearing stratum if the soil immediately beneath the base of the foundation does not have sufficient capacity. The bridge across River Mandovi, Goa is in its construction phase as a part of the development plan of Goa State Infrastructure Development Corporation Ltd (GSIDC). The project was awarded to M/s. L&T Construction, Heavy Civil Infrastructure; subsequently the geotechnical investigation was awarded to M/s L&T Geostructures.The client has specified the foundation of the bridge as rock-socketed. Rock socketing is generally done to achieve higher bearing pressure through concrete-rock shear interface which many building codes permit. The design and construction of rock socketed pile foundation entails a detailed analysis and judgement on the superstructure loads, predominant geological conditions as well as ground water levels. The termination of pile is normally based on thumb rule of half to three times the pile diameter into the rock. Quite often the criteria is based on chisel penetration rate (Gandhi,1990) In fact, this is the key factor to consider appropriate and economical depth of embedment of pile into rock stratum which necessitates enormous understanding on the type and quality of rock strata encountered which may significantly influence the selection of suitable rotary rig for pile installation. Such criteria are site specific and also applicable for the set of equipment used for the particular project."

Jan 1, 2015