Search Documents

By Krishnendu Mandal

"For a multi-story building project in Kolkata, a pile load testing program was conducted to minimize pile performance uncertainty resulting from variable subsurface conditions and to verify the pile load vs. settlement response. The program consisted of performing five (5) instrumented load tests on augured cast-in-place (ACIP) pre-production test piles. Vibrating-wire strain gages and extensometers were installed in the test piles at strategic locations to enable measurements of the load vs. deformation behavior of the test piles. This paper presents a description of site subsurface conditions, test pile installation, instrumentation setup for a maintained load test (MLT), static compression pile load test results, and pile instrumentation result interpretation. Average mobilized unit shaft resistance values are calculated.2.0 INTRODUCTIONThe project site is located in Kolkata, near river Ganges, and the proposed development plans consist of constructing six (6)25-story (G+25) towers; see Fig. 1 and Fig. 2 below for approximate site location and proposed development layout, respectively. The buildings were designed to be supported on ACIP piles. A field load test program was implemented to verify sub-surface conditions and pile design. The test program consisted of installing Five (5) instrumented test piles numbered LP1A and B through LP6A and B, and performing static compression load tests on these piles. The piles were instrumented with vibrating-wire strain gauges and extensometers, so that the pile shaft resistance distribution along pile length and the pile toe resistance could be interpreted using direct instrumentation measurements."

Jan 1, 2015

By Lorie M. Dilley

Alaska Village Electric Cooperative (AVEC), an electric utility cooperative providing power to 51 Alaska villages, has made a concerted effort to install wind turbines in the villages they serve in an effort to mitigate the growing costs of electrical power generation. The subsurface soils in several of these villages consist of sands and silts with ground temperatures of between 30°F and 32°F. The presence of warm, degrading permafrost in three of the villages has required innovative foundation designs, including the use of helical piers and piles to support steel and concrete wind turbine foundations. The design of the deep foundations had to account for the effects of degrading permafrost likely resulting from observed climate change patterns. Uplift forces imposed on the foundations were approximately 100 kips per pile. Uplift pile load testing was conducted on the installed piers and piles in order to determine the actual working load that each pier or pile could sustain. In addition, pile driving analyzer testing was conducted on several piles installed in the permafrost and compared to pile load tests. Results indicated that the installed piers and piles achieved the necessary capacity with sufficient factors of safety. Thermosyphons were installed near the foundations in order to limit the effects of climate change on the permafrost. The two to four wind turbines in each of the three villages are currently operational. Refinement of the design based on the pile testing from the first village to the third has decreased the cost of the tower foundations and improved our understanding of designing for warm, degrading permafrost.

Jan 1, 2010

By Pete Howell, Patrick Granitzki, Alicia Plinio, Janitha Batagoda

The New York City Housing Authority (NYCHA) Red Hook Houses was subjected to damage during Superstorm Sandy. As a result, the NYCHA has an ongoing project known as Restoration Associated with Sandy Recovery Program to improve the resistance against future storms. The specific project included 28 residential buildings and several service buildings within the Red Hook Development. The subsurface conditions within the eastern portion of the site included existing fill material underlain by varying stratums of very loose, loose and medium dense silty sands followed by very soft to medium stiff clay or dense silty sands. The western portion of the site included existing fill material, very loose to medium dense silty sands and organic clayey silts underlain by very soft to medium stiff sandy silts. Based on the geotechnical report, a conventional driven steel pile system was specified containing two pile depths. As part of the project bidding, an alternative pile type was recommended and analyzed to provide quicker installation, reduce vibrations, reduce noise, and provide relatively large cost savings. Due to relatively high lateral loading, an innovative double steel casing drilled displacement piles was proposed as the alternative pile option. Field testing proved the piles capable of the required project capacities and the use of drilled displacement piles as the best alternative for the project and accepted by the NYCHA.

Oct 1, 2022

By Matt Fenwick, Douglas R. Schwarm

Stringent underwater noise limits at the Fairview Ave. N. bridge replacement on Seattle's Lake Union required an innovative approach to supporting the 470-ft long drill trestle. Screw-in foundations would reliably mitigate noise, but the required 500-kip bearing resistance were an order of magnitude higher than typical helical piles. This paper describes the process of designing, installing, monitoring, and testing 22-inch dia. helical piles 80 feet long with 36- and 42-inch dia. helices. A static load test confirmed that the conventional k-factor design method can be extended to capacities of up to 800 kips. A 375 ft-kip drive mechanism had to be fabricated because no North American equipment could supply the necessary installation torque. Real time installation monitoring and later "re-torque" tests confirm that helical piles gain capacity with time, analogous to driven piles under restrike. Underwater and on-land measurements confirmed very low noise, suggesting the possibility of widespread adoption where similar limits are imposed. Overall, this case history illuminates the need for innovative deep foundation types in response to ever-increasing regulatory constraints.

Sep 8, 2021

By Pancho J. Garza, Keith H. Dahlen, Chris A. Labye

"Design for reconstruction of the East Flagstaff traffic interchange project located in Flagstaff, Arizona posed particular challenges. The proposed design included construction of a nearly 50-foot tall mechanically stabilized earth (MSE) wall given rightof- way constraints and soft subgrade soils. The tight right-of-way, approximately 15 feet in certain locations, adjacent to existing structures limited the number of viable remedial alternatives to provide grade separation at the proposed bridge abutment without significant settlement. Preliminary analyses indicated the existing subgrade soils - consisting primarily of relatively soft silts and clays with decomposed pumice - would settle approximately 12 to 14 inches resulting in unacceptable wall deformation. Stone columns placed via vibratory methods (vibro-replacement) consisting of circular excavations which penetrate to firm bearing soils and which are filled with crushed stone were selected to densify the existing subgrade soils. The implemented mitigation measures helped limit settlement to less than one inch and allow for successful construction of the project. The project history - including site constraints, subsurface conditions, evaluation of remedial alternatives, stone columns methodology, and effectiveness of ground improvements - will be discussed.IntroductionThis paper describes the subsurface investigation performed for the reconstruction of the Business Route 40 (B-40) (Country Club Drive) and United States (US) 89 Traffic Interchange (TI) located within the city limits of Flagstaff, Arizona. This project is currently referred to as the East Flagstaff TI. The Project Site Vicinity Map is shown below.The former B-40/US 89 TI was considered ineffective in handling the current and projected volumes of traffic which transition from northbound (NB) B-40 to US 89 (both directions), as well as from southbound (SB) US 89 to SB B-40. The intent of the project was to reconstruct the TI to better accommodate projected traffic volumes. The project eliminated the existing ramps from both NB B-40 to SB and NB US 89. The new interchange includes a Tee intersection from B-40 to US 89. In order to accommodate this alignment, the profile of US 89 was raised several feet (on nearly the same as existing horizontal alignment) to match the elevated profile of B-40. B-40 was shifted just west of its current alignment to accommodate construction of a new, wider bridge structure which spans over Industrial Drive, the Burlington Northern Santa Fe (BNSF) railway, and old Route 66. South of the new bridge, B-40 transitioned back to the existing alignment just north of the I-40/B-40 TI. Within the project limits, both US 89 and B-40 were widened to three travel lanes in each direction."

Jan 1, 2015

By Ralphie Adams, Tiana Rasmussen, Ashley E. Shirer

Transmission line foundation designers must rely on limited subsurface information, from easily accessible locations, resulting in subsurface uncertainty, increased design risk and increased construction costs. This paper presents a different approach for foundation analysis conducted in mountainous and alluvial floodplains located northwest of Phoenix, AZ. The region is dominated by fault-bounded, northeast dipping mountain ranges, where rock types and drillability can vary from granite to intact basalt. The valleys between are comprised of “basin-fill” deposits ranging from conglomerates and cemented soils to lose alluvium. Recently deposited alluvial fills can vary in depth significantly from location to location due to erosion and deposition from active and historic hydraulic features. To limit the subsurface uncertainty for foundation design, a phased approach using geophysical surveys along with detailed geologic reconnaissance was employed. Both compression wave and shear wave velocities were measured in order to identify the depth and properties of loose erodible materials from more scourresistant cemented, conglomerate, and rock deposits. These analyses were used in combination with limited subsurface drilling and sampling to evaluate direct embedment steel pole foundations for over fifty structures. Post analysis results from limited construction drilling reports were used to assess this approach.

Sep 8, 2021

By Abolfazl Eslami, Sepide Lotfi, Mohammad M. Eslami

"Via direct CPT methods for pile capacity prediction, correlation coefficients smaller than unity are used to relate cone tip resistance (qc) and sleeve friction (fs) to pile toe capacity (rt) and shaft capacity (rs), respectively. For linking CPT data to pile capacity, factors such as diameter, penetration rate, partial embedment of pile toe into a hard layer, mechanism of plunging, failure zone, data processing, and stress-strain conditions must be considered. The aim of this paper is to investigate the role and significance of scale effects and establish direct relation between CPT data and pile shaft capacity. A database has been compiled including 40 full scale pile load tests and CPT sounding records for calibration and validation of the proposed approach. Analytical studies demonstrate that differences between pile and penetrometer penetration rate, geometry, and stress-strain conditions influence the relation between fs and rs. By considering the determinants, a procedure is proposed from which the pile shaft capacity can be predicted. This approach demonstrates better agreement with measured capacity by static loading test and less scatter than other current CPT methods.IntroductionAmong different approaches for pile capacity prediction, in-situ tests such as SPT and CPT have been used as supplementary of static analysis. Due to similarities between CPT and pile, the measured cone tip resistance and sleeve friction can be employed for prediction of unit toe and shaft capacities, respectively.Determination of pile capacity from CPT data includes two main approaches: direct and indirect methods. Direct CPT methods apply the measured values of cone tip resistance (qc) for pile toe capacity (rt), and sleeve friction (fs) for pile shaft capacity (rs) with some modifications regarding scale effects. Indirect CPT methods employ friction angle and undrained shear strength values that have been estimated from CPT data.When using direct CPT methods to relate qc and fs to rt and rs, correlation coefficients smaller than unity are used. Factors such as diameter, penetration rate, mechanism of plunging, failure zone, data processing, and stress-strain conditions must be considered for correlation between CPT and pile capacity. The work presented in this paper aims toward ameliorating the situation in the area of pile shaft capacity prediction, based on cone sleeve friction.Case histories from full-scale tests are compiled and analyzed by means of six methods including five direct CPT methods for shaft capacity prediction and the proposed method."

Jan 1, 2015

By Larry Rayburn

Augercast piles evolved in the late forties from the process of pressure grouting open holes backfilled with stone. In 1956, a patent was issued for a cast in situ pile by pumping high pressure grout through hollow-stem, continuous flight auger as the auger is gradually withdrawn from the ground. The patent rights expired in 1973 and the use of auger-cast piles greatly expanded with most large deep foundation contractors now installing augercast piles. At one time augercast piles had a bad reputation, partly because of not having a blow count to give some engineers a confidence factor and there were some quality issues. Over the years the quality issues have been eliminated and I am sure the augercast is the most installed pile in private industry and is now being used by some State Agencies.

Jan 1, 2005

By Johannes Labenski, Christian Moormann, Johannes Aschrafi

"Open steel pipe piles are used for various applications in costal engineering, port structures and increasingly important for offshore structures. During the installation of open steel pipe piles the formation of a plug has an influence on the installation process of the pile and also on the final bearing capacity. The formation of the plug depends on different factors, e.g. the pile diameter and the installation method. This paper starts with a structured overview about analytical methods (API, EAP-EAU, UWA-05, HKU-12, Modified API) to calculate the axial bearing capacity of open steel pipe piles. The numerical simulation of the installation process of open steel pipe piles has to fulfill high demands, i.e. to accurately represent the penetration of the pile inside the soil, the formation of the plug and also the stresses and strains during the installation. A numerical back analysis of a comprehensive field test, using the Coupled Eulerian-Lagrangian (CEL) method and a hypoplastic constitutive model for sand, reveals the stresses and displacements of the soil and of the piles. The analysis provides a comprehensive understanding of soilpile interaction.INTRODRUCTIONThe particular difficulty in the numerical simulation of plug formation, is that the effect of plugging inside open ended steel pipe piles has not been fully investigated. In scientific papers different approaches are documented to explain this phenomenon. Some are based on in-situ tests and others are based on numerical simulations. One of the challenges is to determine the end bearing capacity and shaft friction of the steel pipe pile. Different approaches have been developed over the years to determine them e.g. from Randolph et. al. (1991, 1994) and Paik et. al. (2003). Recent approaches are the ICP-05 Method (Jardine 2005), the UWA-05 Method (Lehane 2005) and the HKU-12 Method (Yu & Yang 2012a). A comparison of some methods can be found in Schneider et al. (2010). A plug inside an open steel pipe pile can be visualized as a spatial bracing of soil between the inner surfaces of the pile, cf. Lüking (2010).. However according to Lüking & Kempfert (2012) this bracing only exists for the height in the end of the pile equal to twice its diameter.To identify a plug inside a pile, there are different measurable parameters. One parameter is the development of stresses around the pile during and after its installation. Henke (2013) measured the inand outside horizontal stresses at the pile tip during the installation. The results showed higher stresses on the inside compared to the outside. To validate his measurements he performed a numerical back-analysis of the measured installation process and got matching results."

Jan 1, 2017

By Siavash Mahvelati, Alireza Kordjazi, Joseph Thomas Coe

Deep foundations are often constructed as end bearing members with a significant amount of their capacity derived from bedrock. Sites with highly variable bedrock conditions therefore present a unique challenge when attempting to estimate the design elevation of deep foundations. Typical subsurface characterization techniques such as drilling, standard penetration testing (SPT), and cone-penetration testing (CPT) may fail to adequately establish top-of-rock elevation in geologic settings prone to karst and/or significant amounts of residuum, saprolite, and deformed bedrock. Seismic surface wave geophysical methods have been increasingly used to map bedrock topography in such settings. However, the current standard of practice for these methods introduces resolution limitations in spatially variable subsurface conditions due to averaging effects from the analytical framework used to process the acquired data. This study explores the use of a tomographic approach with full waveform inversion (FWI) to map top-of-rock elevations at a numerically simulated site representative of highly variable bedrock topography. Comparisons are made with seismic refraction (SR) and a dispersion-based multichannel analysis of surface waves (MASW) approach as more commonly used in geophysical subsurface investigations. The results highlight that FWI provides a superior estimate of top-of-rock topography than SR and MASW at a cost of a significant increase in the required computational resources and time.

Sep 8, 2021

By Siavash Mahvelati, Alireza Kordjazi, Joseph Thomas Coe

Deep foundations are often constructed as end bearing members with a significant amount of their capacity derived from bedrock. Sites with highly variable bedrock conditions therefore present a unique challenge when attempting to estimate the design elevation of deep foundations. Typical subsurface characterization techniques such as drilling, standard penetration testing (SPT), and cone-penetration testing (CPT) may fail to adequately establish top-of-rock elevation in geologic settings prone to karst and/or significant amounts of residuum, saprolite, and deformed bedrock. Seismic surface wave geophysical methods have been increasingly used to map bedrock topography in such settings. However, the current standard of practice for these methods introduces resolution limitations in spatially variable subsurface conditions due to averaging effects from the analytical framework used to process the acquired data. This study explores the use of a tomographic approach with full waveform inversion (FWI) to map top-of-rock elevations at a numerically simulated site representative of highly variable bedrock topography. Comparisons are made with seismic refraction (SR) and a dispersion-based multichannel analysis of surface waves (MASW) approach as more commonly used in geophysical subsurface investigations. The results highlight that FWI provides a superior estimate of top-of-rock topography than SR and MASW at a cost of a significant increase in the required computational resources and time.

Oct 1, 2021

By Takefumi Takuma, Tsunenobu Nozaki, Masashi Nagano

Using sheet piles and pipe piles for permanent earth retaining is one of the most economical methods for constructing basement walls since they can also work as temporary shoring during construction. A major mixed-use redevelopment project in the UK, encompassing two to three large city blocks, utilized both sheet and pipe pile walls for a two-level subterranean parking structure. The 290m (950ft) x 100m (330ft) basement’s steel walls were designed to temporarily support excavation during construction and eventually to become a load carrying permanent structure in order to expedite the construction process and to achieve cost reduction. Two types of press-in piling machines, one for sheet piles and the other for pipe piles, were used for the job because of their abilities to press in sheet and pipe piles within tight tolerances for finished walls, for difficult installation conditions with very hard soil, and for its very low noise and practically zero-vibration operation; an essential factor for the job in close proximity to other businesses and residents. BACKGROUND Steel sheet pile and pipe piles have been used for many purposes including earth retaining. They are produced at steel mills and spirally welded at a fabrication yard to their corresponding specifications under strict quality control measures. Therefore, they can form highly reliable walls to its design capacity with proper installations. Their advantages as underground walls are:  They can form a high level of water cut-off function with their interlocks sealed by welding or with hydrophilic materials. See Figure 1 for a few examples for a sheet pile application.  They can carry vertical loading in addition to horizontal load and bending moment.  They can be a self-standing and temporary/permanent wall with flexible design and construction processes; bottom-up, top-down or hybrid sequences can be chosen per the project’s needs.  They can form a thinner wall than other wall types, creating larger inner space. See Figure 2.

Jan 1, 2019

By Mario Mauro, Jeff Taylor, Carlos Morales

"In 2007 the US Army Corps of Engineers classified the Herbert Hoover Dike in Florida as a Dam Safety Action Classification (DSAC) 1 dam, and started the implementation of one of the largest dam rehabilitation projects in the nation. The construction of the cutoff wall is a key feature of this rehabilitation work to upgrade the dike to current dam safety criteria. The cutoff wall installation is currently being completed on Reach 1, which extends from Port Mayaca to Belle Glade, under a Multiple Task Order Contract based on performance specifications and stringent verification criteria.For the construction of the cutoff wall TREVIICOS selected the self-hardening slurry method. Since the cutoff wall is installed through a layer of highly variable limestone with Unconfined Compressive Strength (UCS) up to 14,000 psi, the excavation requires the use of the hydromill equipment. This is the first successful application of the hydromill technology with self-hardening slurry in a large scale project in the US. This paper presents the details of the method utilized, the quality control procedures, and the experience gained over seven miles of cutoff wall installed.INTRODUCTIONProject LocationThe Herbert Hoover Dike (HHD) system, around Lake Okeechobee in South Florida, consists of a series of levees, culverts and locks and is approximately 143 miles long (Figure 1).Lake Okeechobee is the second largest freshwater lake in the lower 48 states of the United States. The lake is the primary drinking water source for numerous communities around the lake and to millions of people living along the lower east coast. The lake is also a vital source of irrigation for the agricultural industry in the South Florida region.Lake Okeechobee is 33 miles wide from north to south and 30 miles wide from east to west and has a surface area of 730 square miles. The average water depth of the lake is 9 ft."

Jan 1, 2017

By Tian Miaomiao, Cheng Yin, Shen Jun, Yu Hao, Li Yafei

Vast amounts of waste drilling mud containing heavy metals is produced during oil drilling process, which causes great pollution to the environment. Therefore, it needs to be treated until it is harmless. This study uses industrial waste and Portland Cement stabilized waste drilling mud; the unconfined compression strength, leaching amount of Pb2+ and Cr6+ ions, and pore size of the stabilized soil were tested at different times during freezing-thawing cycles. The antifreeze performance of the stabilized drilling mud with industrial waste is discussed. The results show that the strength of the stabilized soil decreases with an increase in the number of freeze–thaw cycles. The strength loss of the stabilized soil after freeze–thaw cycles can be effectively reduced by increasing the industrial waste content, especially the content of phosphogypsum in the stabilizer component. Pb2+ ions and Cr6+ ions can be effectively stabilized by industrial waste. The results of the pores test prove that the compactness of stabilized soil solidified by industrial waste residue is greater than that of cement alone.

Nov 1, 2022

By N. Aarthi, G. R. Dodagoudar

The improvement of soft clay deposits using stone columns is a well-established ground improvement technique in the western world. This technique has been well documented and has proper design codes for precise execution in the field. The sand compaction pile (SCP) method is a contemporary technique to stone columns and has limited literature related to the strength characteristics of the loose to medium dense sand deposits treated with SCP. The available studies on the SCPs installed in cohesionless deposits focused on the improvement by indirectly assessing the SPT-N values pre- and post-installation of the SCPs. The widespread implementation of the SCP technique in recent years has increased the need for a more direct evaluation of the improvement. Earlier studies in this regard have revealed that the available design solutions are based on the type of installation equipment, their working efficiency, and accumulated field data. However, it is found that there are no generic design codes for the direct estimation of the ultimate bearing capacity of the SCP improved cohesionless deposits. To meet the design requirement for the SCP treated ground, a series of experimental and numerical investigations are performed in the present study to arrive at a direct framework in the form of design charts based on the pressure-settlement response of the treated ground. The developed design charts give the ultimate bearing capacity (UBC) of the treated sand deposit for the known initial relative density (RD) of the deposit, spacing and diameter of the SCPs, size of the footing, and for the specified target unit weight required for the intended application. It is concluded that the design charts will be of preliminary use to the design engineers to directly evaluate the UBC of the SCP improved loose to medium dense cohesionless deposits as part of the SCP method of ground improvement. It is expected to have more field-scale experiments and in-depth analysis before implementing these charts for actual field execution.

Nov 1, 2022

By Kenneth R. Chadwick, Thomas J. Tuozzolo, Terence P. Holman

"Micropiles are often installed to retrofit existing foundations that experience distortion and to underpin structures prior to future construction. The Dublin Road Pump Station project is an example of retrofitting due to a basal failure during construction that compromised the bearing capacity of the soils. A completed pump station settled and had to be restored to its original position, and work could not proceed until a new support system for the partially completed wet well could be designed and installed. The project involved the construction of three below-grade structures for a new pump station in a growing area of Jackson Township, N.J. The general contractor constructed three pump station structures consisting of a pump chamber, wet well and an inlet chamber in early 2006.The geologic conditions beneath the project site (Figure 1) consisted of loose/soft to medium dense/stiff sand, silt and clay to a depth of 40 ft below ground surface, underlain by medium dense to dense glauconitic silty fi ne sand. When the general contractor was constructing the wet well, which involved an internally supported sheet pile excavation 32 ft below the ground surface and 28 ft below the static groundwater level, basal failure, boils and ground loss occurred. Driven piles were installed to support the wet well structure, but additional ground loss was observed within and outside the sheet pile excavation, followed by settlement of the adjacent pump chamber structure. Post-failure investigations were conducted by Mueser Rutledge Consulting Engineers, N.Y. (MRCE), a geotechnical and foundation engineering consultant. Their investigation concluded that the ground losses around the pump station structures had compromised the supportive capabilities of the natural subsoils.The owner engaged Moretrench, a geotechnical specialty contractor, to work with MRCE to develop a constructible solution to support the pump station structures in general and to restore the pump chamber to its original position. Knowing that ground loss had already occurred as a function of the initial basal heave and subsequent pile driving, the team selected micropiles as the preferred foundation element, primarily due to their flexibility in bypassing these disturbed zones and generating capacity as a function of grouting volume and pressure. Drilled piles were also recommended due to concerns about causing additional settlement of the pump chamber if driven piles were used."

Jan 1, 2008

By Min Sunn Ye, Wei Wang, Huawen Xiao, Kai Yao, Fook Hou Lee, Siang Huat Goh

"Previous research have shown that introducing fibers to cement soil mixture is effective in improving the ductility as well as maintaining the strength of cement-treated soil. A good knowledge of stiffness of the improved soil at small strain is essential for realistic predictions of ground movements that may affect adjacent buildings or underlying infrastructure. This paper presents a triaxial system with local strain measurement developed for studying shear modulus degradation of cement treated clay with fibers. Cylinder specimens (70mm diameter by 140mm height) with 50% cement, 100% water, 0% to 1% polypropylene fibers by mass, and 7 days of curing period were used. A local strain measurement system with floating type miniature submersible LVDT is introduced in this paper. Configuration of the mounts including the pin size, length and distance are presented and discussed. Based on the experimental results, a reasonable configuration of the mounts is recommended for fiber reinforced cement treated clay. Results showed that the proposed local strain measurement system is effective for testing the shear modulus degradation of cement treated clay with fibers under both unconfined and confined condition. Comparisons with results from resonant column and bender element tests served to verify the reliability of the local strain measurements using the proposed method.INTRODUCTIONIn many geotechnical engineering problems, the operational strain domain ranges from 10-3% to 10- 1%. A good knowledge of stiffness at small strains is essential for realistic predictions of the ground movements that may affect adjacent buildings or underlying infrastructure. As such, during the last 3 to 4 decades, the importance of using the small strain stiffness of soils for the design of foundation and underground structures has widely been accepted. Triaxial testing has been widely used to study the stress-strain behavior of soil in the laboratory. However, the stiffness obtained from the conventional triaxial apparatus is usually far smaller than those back-calculated from field measurements. This is mainly attributed to the overestimation of axial strains from the external strain measurements, which usually includes compliance effects of the loading and load measuring system as well as sitting, bedding and alignment errors between sample and system (Baldi et al., 1988). The poor resolution of the external strain measurements is another important contribution. Therefore, conventional procedures are inappropriate for small-strain stiffness evaluation due to low accuracy and resolution."

Jan 1, 1900

By Garland Likins, Gray Mullins, George Piscsalko

"Quality control of drilled shafts is greatly dependent upon the practices of the site personnel. For drilled shafts cast under slurry, inspection of the hole prior to concreting is very difficult or impossible. There are numerous non-destructive test (NDT) methods currently available to assess the integrity of drilled shafts. This paper will discuss the theory and use of an emerging NDT technology known as Thermal Integrity Profiling (TIP). The Thermal Integrity Profiling method measures the elevated concrete temperatures that occur during the hydration process. These temperature measurements are made along the length of the pile and can determine the integrity over 100% of the pile cross section, both inside and outside the reinforcing cage. With the known shaft volume information, TIP can evaluate the effective shaft radius at each measurement location. With the increased use of TIP on highway projects, there is a need to have standard criteria for shaft acceptance. Shaft acceptance criteria can be based upon thermal measurements and subsequent analysis of the data to determine the average shaft radius, local concrete cover, and cage alignment. With this additional information obtained via the thermal testing method, acceptance methods based upon concrete cover can be developed. In this paper the Thermal Integrity Profiling method will be described, results from a case history will be discussed, and an acceptance criteria based upon concrete cover will be proposed.INTRODUCTIONDrilled shafts are an attractive foundation element in many applications due to their large axial and lateral capacities. When drilled shafts are cast in a dry hole, it is possible to inspect the hole prior to casting, allowing for very basic level of quality control, although the shape of the completed element is still unknown without some form of post construction testing. When drilled shafts are installed where soil conditions are unstable, the shafts will often be cast under slurry to support the surrounding soils during the construction process. When casting a drilled shaft under slurry, it is very difficult to impossible to accurately and efficiently inspect the hole prior to casting concrete and it is equally difficult or impossible to inspect the shaft during the casting process"

Jan 1, 2016

By Gust Van Lysebetten, Monika de Vos

The objectives of monitoring geotechnical structures can be very diverse, including optimisation of the design, quality control, long term performance assessment, and approval of innovative execution techniques. In this context, new measurement techniques, based on optical fibres, offer the possibility of accurate strain and temperature monitoring with very small sensors and limited numbers of cables. This paper briefly presents optical fibre sensing techniques and illustrates their application to geotechnical structures by means of some projects, carried out by the Belgian Building Research Institute (BBRI).

May 1, 2022

By Suthan Pooranampillai

Verification of drilled shaft resistance is primarily obtained through the use of different load testing methods. Procedures utilized include conventional top down static loading, the Osterberg load cell (O-cell) test and dynamic tests such as the Statnamic method. The O-cell test provides a means of obtaining separately the base and side shear resistance behavior of drilled shafts (cast-in-drilled-hole). Alternatively, the Statnamic load test method enables the engineer to derive base and side shear behavior separately, based on measurements of load, accelerations and strains along the length of the shaft. However, due to time and cost constraints these tests can only be performed on selected shafts within a project. Post grouting of a drilled shaft base embedded within a cohesionless material, with a low mobility compaction grout, will essentially pre-load the shaft base soil against the side shear and self-weight in much the same manner as an O-cell load test (when the load cell is placed within the base vicinity). Therefore, successful post grouting of a drilled shaft would enable verification of both shaft side shear and base resistance simultaneously on each and every shaft it is carried out on. Additionally, such post grouted shafts display stiffer load-displacement response during subsequent downward, superstructure induced, loading compared to ungrouted shafts. Verification of resistance on each and every shaft through the use of post grouting will allow an increase in resistance factors (reduction in safety factor) used in the design. Two 6 ft. diameter drilled shafts were constructed in Fredonia, WA, for WSDOT, each with an approximate length of 52 ft. The shafts were terminated within medium dense poorly graded silty sand. Statnamic load testing of the shafts indicated maximum derived static side shear and base resistances of 2545 kips and 507 kips (1.6 in. displacement) for shaft One and 2466 kips and 212 kips (1.4 in. displacement) for shaft Two. Shaft Two was subsequently grouted, with a low mobility compaction grout. Shaft base mounted total earth pressure cells measured a maximum sustained pressure of 55.44 ksf during the compaction grouting operation. Shaft displacement reached 0.65 inches in the upward direction at termination of grouting. Comparison of grouting data with initial load test information indicates that properly instrumented post grouting verifies shaft base and side shear resistance. In addition, these grouting induced resistances were much higher than design values supplied by the engineer using conventional resistance factor design. Large scale laboratory testing also shows that base grouting verifies higher soil resistances than permissible in conventional design.

Jan 1, 2010