Search Documents

By Melissa S. Beauregard, Randall A. Pietersen

This study focuses on quantifying the effects of water infiltration on a full-scale energy pile system’s ability to meet the thermal demand of an HVAC system. Theoretically, an energy pile system should increase its thermal capacity after a rain event due to increased moisture content creating an increase in thermal conductivity of the surrounding soil matrix. The United States Air Force Academy has an energy pile research site consisting of 8 full-scale energy piles located below a shower facility. The local colluvium surrounding the piles allows for relatively high water infiltration during rain events. This study uses an 11kW Precision Geothermal Geocube to apply a thermal load on two single-loop piles. A weather station located south of the structure records atmospheric conditions. Results indicate that moderate rain events can caused up to a 23% increase in the system’s thermal exchange capacity. This change is due to the increase in moisture content near the surface, which penetrates to deeper soil layers with time. The time required for moisture to penetrate to greater depths and then dissipate in the soil matrix, explains why increased system performance is seen for over a week following the passing of a singular rain event. 1 INTRODUCTION With a “future-forward” focus, there is an ever-pressing economic and environmental need to use sustainable sources to meet growing energy needs. HVAC is typically responsible for 34% of the overall energy required by commercial buildings and 48% of the energy required by residential buildings (USEIA, 2009; USEIA, 2012). Energy piles are a low cost, sustainable technology that have been used to offset this energy demand incurred by a building’s space heating and air conditioning requirements. An energy pile consists of heat exchanging elements in a closed loop system integrated into a building foundation and connected to a ground source heat pump (GSHP). It is most common for these heat- exchanging elements to be constructed within a drilled shaft foundation due to both construction practices and geometric considerations. This system operates based on the principle that at a certain depth below ground (typically 4 meters) subterranean temperature remains constant at a value equal to the mean annual air temperature at a given location (Kavanaugh et al., 1997). This allows the soil to function as a heat sink for cooling operations and a heat source for heating operations when exchanged within this zone of relatively constant temperature. For the past 25 years, the implementation of energy pile technology in public, residential, and even large-scale architectural complexes has slowly expanded which has created an increase in research into the topic as a result (Brandl, 2006; Hamada, 2007; Sekine et al., 2007; Gao, 2008; Bourne-Webb, 2009; Stewart and McCartney, 2013; Murphy et al., 2014). When pile construction takes place beneath the groundwater table, soil is under fully saturated conditions, maximizing thermal exchange for a GSHP system. Under unsaturated conditions, however, changing moisture contents change thermal conductivity values in a soil, which affect a GSHP system’s ability to meet a thermal demand. The observational data presented in this paper apply to GSHP systems in unsaturated soil conditions.

Jan 1, 2019

By Suzanne R. Hess-Brittelle, Sharon L. Schulz, Tyler J. Quick, Amy F. Ebnet

"Abiquiu Dam is a rolled earth fill dam with impermeable core located on the Rio Chama in New Mexico. Abiquiu has had a history of excessive seepage through the fractured sandstone abutments since water was first impounded in 1963. The foundation was treated with a single row grout curtain in the cutoff trench prior to placement of the embankment. During the 1960’s and 1970’s, the grout curtain was extended 1,000 ft. into both abutments and sections of the foundation beneath the embankment were regrouted. Grouting of the foundation beneath the embankment required drilling through the embankment. Drilling fluid loss or loss of circulation within the impervious core was observed during multiple phases of supplementary grouting and during verification drilling following the 1970’s grouting program. It is likely that the drilling methods employed for these grouting and drilling programs caused hydraulic fracturing of the impervious core. The fluid losses in the embankment may be related to seasonal shutdown layers in the embankment or benches in the abutment foundations. In addition, it is likely that the impervious core was fractured from grout pressures during installation of grout pipe through the embankment.INTRODUCTIONAbiquiu Dam is located on the Rio Chama in New Mexico and consists of a rolled earth fill dam with impermeable core, controlled outlet works, and an uncontrolled rock-cut spillway. The dam was authorized for flood control and sediment retention and was designed as a dry dam, holding flood pools for relatively short durations. The foundation is comprised of Permian and Triassic age, interbedded mudstones and sandstones that were deposited in an active braided stream system. Sandstones are moderately fractured and have variable aperture and infilling. Generally speaking, joints are near vertical. Abiquiu has had a history of excessive seepage through the fractured sandstone abutments since water was first impounded in 1963. The foundation was treated with a single row grout curtain in the cutoff trench prior to placement of the embankment. In 1966-1968, the grout curtain was extended 500-ft into the left abutment and the foundation beneath a 560 ft. section of the embankment was re-grouted. In 1978-1980, the grout curtain was extended 1,000 ft. into the right abutment, an additional 500 ft into the left abutment and the foundation beneath the right 520-ft section of the embankment was re-grouted. The alignments of these grout programs are shown in Figure 1. Grouting of the foundation beneath the embankment required drilling through the embankment. Drilling fluid loss or loss of circulation within the impervious core was observed during both phases of supplementary grouting and during verification drilling following the 1978-80 grouting program. It is likely that the drilling methods employed for these grouting and drilling programs caused hydraulic fracturing of the impervious core. In addition, it is likely that the impervious core was fractured from grout pressures during installation of grout pipe through the embankment. This paper provides a summary of the drilling and grouting methods used during these programs and the potential for damage to the embankment."

Jan 1, 2016

By Mohammad Ali Rowshanzamir, Mehdi Aghayarzadeh

"This article is an effort to improve our understanding of the performance of geogrid retaining structures (GRS) through numerical analyses. The numerical modeling utilized a commercially available finite difference program, FLAC3D. In this context an extensive parametric study has been carried out on two different GRS walls (vertical reinforced block and inclined reinforced block) to investigate the influence of internal design factors such as soil strength properties and reinforcement stiffness on the performance of these walls. The main purposes of the parametric study were to (1) investigate the sensitivity of the modeling results to the input material properties, (2) examine the influence of the internal design factors on the performance of GRS retaining structures, and (3) improve the internal design of GRS walls on the basis of the working stress information obtained from the parametric study. Based on the analyses results, it was revealed that GRS walls with oblique reinforcement and reinforced block (rotated against natural backfill) have much better performance in terms of reduction in the stresses and strains of reinforcing elements as well as decrease in the wall lateral and vertical displacements in comparison with vertical reinforced block (conventional wall). For example, with 12° inclination of the wall reinforced block there was 50% reduction in the backfill settlement. Also increasing the reinforcement stiffness amount from 10MPa to 50MPa decreases the wall face displacement more than 50% in both GRS walls.INTRODUCTIONOver the past few decades, Geosynthetic- Reinforced Soil (GRS), a soil mass reinforced by geosynthetic layers to restrain the soil lateral deformations, has been employed in the construction of many types of earth structures, including retaining walls, embankments, slopes and bridge abutments. In fact GRS structures are typically more flexible (hence more tolerant to differential settlement), more adaptable to low quality backfill, easier to construct, require less over-excavation, and more economical. Nevertheless, there is a need for an accurate design tool that can predict the performance of GRS structures under working stress conditions and can predict their failure loads as well.Many studies have been published on the performance of the soil reinforced walls such as Isabel et al., 1996; Bathurst et al., 2000; Kazimierowicz-Frankowska, 2005; Nernheim and Bathurst, 2008; Chen and Chiu, 2008 Correia et al., 2012; Erlich et al. 2012. Several numerical studies have also been made throgh finite elements and finite difference techniques on reinforced soil retaining walls to analyze the wall deformations (e.g. Hatami et al. 2001& 2006, Liu and Won 2009, and Abdelouhab et al. 2011). A limited laboratory research has been reported indicating of improving effect of tilting face on GRW performance (Chen and Chiu, 2008). However no major numerical study was found on the effects of face or reinforcement tilting."

Jan 1, 2017

By Zhang Wengang, L. John Endicott

The properties of many geological materials are variable. This is especially true for variations in elevation of the top of rock profile, strength of weathered rock, and conductivity of rock masses. Often the site investigation stage is completed by site specific ground investigation utilizing boring, sampling, and testing. Statistically this is a sampling procedure, but the borings are often widely spaced, and ground conditions between borings are deduced by interpolation. Often budgets are a limiting restraint and the information that is obtained may be less than desired. Sampling and testing is often biased. If claims for unforeseen ground conditions are to be avoided, the properties of the ground should be adequately identified. This paper describes how data can be used to evaluate the subsurface top of rock profiles, and can give insight into representative, maximum, and minimum strengths, and variation in conductivity relating to inflow of water into excavations, that can assist in planning the works and also in resolution, or avoidance, of disputes about unforeseen ground conditions. INTRODUCTION The mechanical properties of the ground are naturally variable. The work of Geologists, Engineering Geologists and Geotechnical Engineers is fundamentally investigative. Frequently, budgets for ground investigation are squeezed, resulting in widely spaced boreholes, with conditions between them determined by interpolation. Profiling can be adopted but the measurement, such as seismic velocity, is used as an indirect means of computing in-situ profiles and mass properties. Often a lot of test data are generated on large projects or by many projects in the same vicinity. Published data enlarge the database for a given project, and databases can be interrogated to gain insight into different categories of ground. Integration with geological studies can then lead to more reliable characterization of the ground in terms of identifying the materials present, their extent and their range of properties. This paper focuses on properties of rocks that are generally required for ground engineering, namely the top of rock profile, the unconfined strength of rock materials, and the mass conductivity. Data are obtained from Granodiorite and Granite in Hong Kong, and from Granite and the Jurong Series of weakly metamorphosed sedimentary rocks in Singapore. All four rock types have been tropically weathered, resulting in widely varying top of rock profiles, material strengths and mass conductivity. With a wide range in values for these parameters, project specific ground investigation conducted within a limited budget may run the risk of falling short of obtaining sufficiently reliable data sets, resulting in risk that unforeseen ground conditions may be encountered.

Jan 1, 2019

By Filippo Maria Leoni, Gianluca Pianezze

"As part of the Southeast Louisiana (SELA) drainage program, designed to reduce flood damages in the City of New Orleans and surrounding parishes, the SELA-22 project entailed the construction of a concrete covered canal along Jefferson Ave. and Prytania Street. The scope of the required soil improvement was to replace the soil between two parallel lines of sheet piles with a soil-cement mass to eliminate under-seepage, thus creating a so called bottom plug, and provide structural support for the concrete box culvert. The U.S. Army Corps of Engineers (USACE), New Orleans District, selected the jet grouting technology for the construction of the bottom plug to a maximum depth of approximately 40 ft, and for a total length of approximately one mile. The specialty geotechnical contractor proposed to accomplish the task utilizing their proprietary and innovative elliptical bi-fluid jet grout technology which, by limiting the overlap between adjacent columns, allowed a reduction of the overall number of installations. Approximately 2,400 elliptical jet grout columns were installed in a very challenging environment, especially under a logistical point of view. This paper will summarize the main features of the project, focusing on the innovative technological solution adopted to maximize productivity and on the several challenges faced in such limited and complicated logistical conditions.INTRODUCTIONThe Southeast Louisiana (SELA) drainage program has been designed with the purpose of reducing flood damages in the City of New Orleans and surrounding parishes. This will be accomplished by constructing new pumping stations and better drainage canals throughout. The program was authorized in 1996 by the United States Congress and administered under a project cooperation agreement between the Sewerage and Water Board of New Orleans (SWBNO) and the USACE.Prompted by the severity of damages associated with rainfall flooding in southeast Louisiana, the SELA program consists of several individual project components. The proposed work is located on both the east and west banks of the Mississippi River in the Orleans and Jefferson Parishes, as well as in portion of St. Tammany Parish."

Jan 1, 2017

By George Burnhart

"Sonic drilling is a relatively new technology even though it has been in development since the late 1940s. It was initially funded by the U.S. petroleum industry and then, in the late 40s, Russian scientists worked on developing sonic drilling, their interest based on drilling rates 3 to 20 times that of conventional methods. In the early 1960s, the Shell Oil Company backed research that resulted in a down-hole device with a series of eccentric weights driven by drilling fluid to generate vibration. Hawker Sidley, in the early 1980s, developed the first modern prototype sonic drills in Vancouver B.C. and the North Star Drilling Company in Minnesota became the first contractor in the U.S. to operate sonic equipment in 1985. In 1994, North Star became a division of Boart Longyear, headquartered in Salt Lake City, Utah.What’s Unique about a Sonic DrillA sonic drill rig appears and operates very much like any conventional top-drive rotary rig. The key difference is that a sonic drill has a specially designed hydraulically powered drill head, containing oscillators, that generates adjustable high-frequency vibratory forces. The sonic head is attached directly to the drill pipe or outer casing, sending the high frequency vibrations down through the drill steel to the face of the drill bit. This creates displacement, fracturing or shearing action depending on the material being drilled. The oscillator uses two eccentric, counter-rotating balance weights or rollers that are timed to direct 100% of the vibration at 0 degrees and 180 degrees. An air spring houses the oscillators and separates the vibration from the drill rig itself. The vibratory frequency is controlled to suit operating conditions and to achieve optimum drilling rates.When the vibrations coincide with the natural resonant frequency of the steel drill rod or casing, a natural phenomenon called “resonance” occurs. It allows the rig to transfer timed vibratory energy into the top of the drill string, utilizing the natural stored energy of the steel. This causes the drill string to use inertia and act like a flywheel delivering tremendous amounts of energy directly to the bit face. In friendly overburden formations, a sonic drill rig can achieve penetration rates of one ft per second."

Jan 1, 2008

By John Vickers, William H. Hover, Paul C. Schmall

"Any sudden subsurface issue that threatens the stability of existing buildings or infrastructure is cause for immediate investigation and prompt remedial action. Nowhere is this more true than the nation’s dams and levees. A breach of any kind, no matter how small initially, has the potential to be catastrophic and impact a wide downstream area. Addressing the problem quickly and effectively is therefore critical. When a turbid water discharge developed from a rock drainage embankment at the toe of the earthen dam impounding Cannonsville Reservoir, near Deposit, NY, the source of the problem was quickly identified as resulting from an artesian water release from an underlying permeable silty sand and gravel formation during drilling of three exploratory boreholes in preparation for construction of a hydroelectric plant at the downstream toe area of the dam facility. Work was halted, intense 24-hour monitoring was implemented, and as a risk reduction measure NYCDEP began to draw down the reservoir’s total storage at a rate of a billion gallons per day. Input sought from contractors within the geotechnical community helped result in the design and development of a deep well system to control the artesian pressure. Once this primary objective was accomplished, modified compaction grouting was performed at the borehole locations to densify loosened soils, fill any voids created by the discharge activity, and seal off the permeable aquifer. This paper discusses the dewatering program, specialized drilling techniques required, monitoring and verification of pressures within the dam, and the grouting program.BackgroundCannonsville Dam, owned and operated by the New York City Department of Environmental Protection (NYCDEP), is located in Deposit, New York on the West Branch of the Delaware River and impounds the Cannonsville Reservoir. Built between 1959 and 1964, the dam has an impervious central and upstream core zone keyed into the glacial till foundation, a semi-pervious downstream embankment zone, and a rockfill toe and is approximately 2,800 ft (853.4 m) long and 175 ft (53.3 m) high. The dam is formed by two embankment sections. The left section forms the main embankment blocking the main river channel, while the right section is constructed over a topographic saddle or low ridge. Reservoir level is actively influenced by withdrawals through the West Delaware Tunnel, based on water supply need. Under normal circumstances, water is continuously discharged downstream to the Delaware River."

Jan 1, 2016

By Brandon M. Robinson, Osman F. Besler, Dominik Gaechter

The Sandbukta-Moss-Såstad (SMS) project is a part of the Intercity development project, which is part of the largest transport project in Norway, consisting of 270 km of new double-track rail. The SMS project consists of 10km of double-track railway including three open stretches and two tunnels. Soil conditions consist of quick clay underlain by Bedrock. Dry soil mixing (DSM) was considered as the main soil improvement method to allow for excavation of the quick clay and construction of the D-Wall panels. The preliminary design revealed around 25,000 ton of binder installation. Therefore, a test field has been conducted to evaluate binder alternatives in means of improved soil strength by considering CO2 emissions. Multicem and Standard cement (Standard FA) have been compared for that purpose. Multicem is a type of binder which mainly consists of Portland cement and cement kiln dust (CKD). CKD is a fined-grained, solid, highly alkaline material removed from the cement kiln exhaust gases. reverse column penetration test (FOPS) and pre-drilled column penetration test (FKPS), which are common tests to evaluate DSM strength have revealed comparable strength outcome for both binder types. Therefore, Multicem has been selected as the main binder type to be used further which provided a reduction in CO2 footprint of up to 40%.

May 1, 2022

By Giulia M. B., Ferruccio Cribari, Alessandro Bertero, Eliano Romani, Roberto Sorge, Francesca Casini

"The use of Artificial Ground Freezing (AGF) to form earth support and seepage control barrier systems has had applications worldwide. These cover a variety of construction problems, including the formation of frozen earth walls to support deep excavations, structural underpinning for foundation improvement, and temporary control of ground water in construction processes. An application of AGF during construction of Line C of Rome underground is described in detail.The new line “C” of San Giovanni metro station was constructed adjacent to the existing line “A” of San Giovanni station; the new metro line “C” is deeper than line “A” and runs below the existing station. The underpass project envisages an Artificial Ground Freezing in order to create a structural and waterproof temporary cut-off suitable to the two new tunnels excavation, while keeping trains running in the safest possible condition. The excavation of tunnels under the water table, with a hydraulic head of over 10 m in not homogeneous soils having different mechanical properties and permeability and below existing sensitive structures, involves special ground freezing sequences and methods, as well as peculiar drilling systems and operations, such as TDDT (Trevi Directional Drilling Technology).Artifical Ground Freezing IntroductionNatural freezing occurs seasonally in many areas of the globe and can affect negatively the engineering performance of geotechnical structures; on the other hand, man-made freezing is a controllable process that can be used by civil engineers to stabilise temporarily the ground in order to support and/or exclude groundwater from an excavation until the final retaining and lining structures are constructed. Freezing and thawing of the pore fluid within soils involve complex thermal, hydraulic and mechanical processes that have significant mutual interactions. For example, phase changes of the pore fluid caused by temperature variations can modify the pore water pressure in the soil, which, in turn, can induce mechanical deformation. At the same time, any changes in the hydraulic and mechanical conditions affect the thermal processes by advection and changes of ice and water contents.An application of AGF which will be presented in the paper, refers to the construction works of Line C of Rome underground. In this case AGF was carried out to provide temporary support during excavation of the two Line C running tunnels directly underneath the existing S. Giovanni station of Line A, in the safest possible condition. In order to keep the trains of Line A operational during excavation, a temporary structure was installed and a real-time monitoring system was conceived in order to control the temperatures of the soil during freezing and the response of the structures of the existing station."

Jan 1, 2016

By Nasr Sheta

"After Hurricane Sandy, the stability of an earth slope in the Atlantic Highlands, New Jersey in the United States was deteriorating due to slumping soils and erosion from flooding. A slope stability evaluation indicated the slope did not satisfy the requirements of the local building code. A triple-tier, pile-supported and mechanically stabilized earth wall was designed and constructed to stabilize the slope. The construction was planned from a 3-m-wide roadway and, because of rough terrain and limited work space at the site, a cast-in-place drilled-pile construction was deemed impractical due to slow pile production. An alternative procedure was utilized by pre-drilling holes, and installing precast tip-and-shaft-grouted (PCTSG) piles, which extended to competent soils to improve slope stability. A grade beam, connecting the PCTSG piles along with soldier beams and concrete lagging were used to form the lowest tier of the slope stabilization, while the middle and higher tiers were built as mechanically stabilized earth. The stability of the proposed stabilization was analyzed using 2-D non-linear finite elements. After construction, monitoring of the wall continued for about 8 months to check its performance, and indicated lateral and vertical wall movements were less than 25 mm and 6 mm, respectively, indicating effective slope stabilization.INTRODUCTIONStabilizing earth slopes using piles to connect near-surface unstable soils to underlying stable ground masses has been investigated by many researchers, who presented various approaches to evaluate the contribution of the pile system towards improving the stability of the slope. Some of these approaches consider the piles as structural elements receiving forces from the upper sliding ground mass and transmitting these forces to the underlying stable one. The force from the top sliding mass is applied at between one third and one half of the pile embedment into the top sliding mass, Anagnostopoulos et al. (1990), Fukuoka (1977) and Matsui et al. (1988). The point of application of the sliding force was explored based on successful case histories while addressing the safety factors for both geotechnical and structural design, Vessely A. et al. (2007). The development of numerical analysis techniques utilizing the method of finite elements (FE) also enabled better analysis and design of slopes stabilized using piles. A FE-based approach was successfully utilized to design slope stabilization with target safety factor based on the shear and bending demands and the spacing of the piles, Pradel D. et al. (2010).After Hurricane Sandy in October 2012, the stability of many properties constructed atop earth slopes located along the coast of the Atlantic Ocean has become a concern due to storm-induced erosion. This paper presents the analysis, design and construction of a hybrid slope stabilization system utilized at one of these storm-impacted properties, which is located in the Atlantic Highlands, New Jersey in the United States. The subject property consisted of a two-story residential dwelling and a parking structure, and was built on top of an about 8-m-high earth slope having crest at about elevation 10 m (el 10) and toe at about el 2."

Jan 1, 1900

By Christophe H. Locussol

D.C. United, the professional soccer team located in Washington, D.C., completed a 20,000 seat capacity stadium in July 2018 named Audi Field. The project initially considered a foundation system consisting of roughly 800 prestressed concrete driven piles configured in groups with pile caps. A value engineering alternative proposed in a design-build manner ultimately resulted in the use of 300 single element Auger Cast Piles (ACPs) for the foundation system. The ACPs ranged between 1.5 ft and 4 ft in diameter, were up to 85 ft in length, and were connected through a system of grade beams to accommodate large lateral induced loads. Limitations in conventional analytical methods were encountered during the structural design of the piles due to the complexity of the lateral loading and pile fixity conditions. An innovative approach using advanced finite element modeling that incorporated the framing effects of the grade beams was required to meet the strict movement criteria despite large lateral loads.

By Gene Bryant, Wesley Schmutzler, Matteo Bertoni

The levees where the Mississippi River and the Lower Wood River meet near East Alton Illinois have been a problem area for years due to underseepage. The first phase of the deep cutoff wall was a 2,000-linear foot section that was completed in 2016 for the Illinois Flood Prevention District Council. This section was installed along the Wood River and the Mississippi river to depths of over 135’, The United States Army Corps of Engineers was tasked with continuing the cutoff wall along the Mississippi river. The wall was a continuation of phase I with depths up to 140’. The 1,000’ long cutoff wall was installed through fill, loose sands, cobbles, and sandy clay. The cutoff wall was terminated in either Glacial Till or sound rock. In order to provide wall permeability equal to or less than 1.0 X 10-6 cm/sec a self-hardening slurry (SHS) composed of ordinary Portland cement, slag cement, and water was utilized. The depths reached on this project using SHS is the deepest done to date in the United States. Along with the permeability requirements, a very narrow range for the unconfined compressive strength was specified at 50 – 180 PSI. In order to monitor the ground movement and water level fluctuations during the excavation of the panels with the Hydromill or Clamshell, 6 automated inclinometers were installed and monitored continuously during panel excavation in phase 1. Seven automated piezometers were monitored in phase 2. This paper will give an overview of the project with emphasis on the effect of the excavation on the instrumentation, specifically the reaction of the piezometers as the last panels were installed. INTRODUCTION The project is in Illinois, about 1000 feet downstream from where the Wood River Creek enters the Mississippi River between East Alton, IL and Wood River, IL adjacent to State Highway 143 (Fig. 1). The Wood River Lower Cutoff Wall Phase 2 Project (WR2) was awarded to TREVIICOS SOUTH (TIS) in September 2017. The Main Project features are: Construction of work platform, inclinometers installation and removal, cutoff wall construction by the Self-Hardening Slurry method (approx. 135,000 sf) up to 140' depth, clay cap installation, and site restoration. The levee system along this stretch of the Mississippi River has been plagued by under-seepage for several years. The phenomenon has worsened to varying degrees, depending on location, to the point that remediation was needed to ensure that Levee failure would not be an issue in the future.

Jan 1, 2019

By Jerold Bishop, Grant Bearss, Aleksey Egorov

"When a shock wave is released in the bottom of a drill hole filled with wet concrete slurry, the result is called an electrohydrodynamic effect, or EHDE. The energy is carried through the fluid with minimal loss because the slurry is an incompressible medium. Repetitive discharges provide a series of energy pulses that compact the soil along the pile shaft and at its base. The process is analogous to repeated applications of low-energy blast densification or to dynamic compaction. In general, the process is not depth dependent. EHDE was identified in the 18th century by an American scientist who observed that a spark between two electrodes placed under water induced a burst of pressure. In 1957, two Russian engineers formulated a process and received a patent for a method of creating a pressure wave by transforming power from an electrical discharge to a mechanical impact. They derived more than 200 applications for technical and industrial processes.In the 1970s, civil engineers at the Engineering and Building Institute in St. Petersburg, Russia, began to look at EHDE to improve the capacity of drilled piles. Early experiments showed that electric discharges in a wet concrete slurry mix could create a pressure wave of up to 26 MPa (3700 psi). Later tests demonstrated that this pressure level could be created in a drilled pile hole. The researchers devised equipment and in the early 1990s began to study pulse technology as applied to drilled piles.This application was accepted into the Russian Federation Building Code in the 1990s. The code treats “regular” drilled piles with equivalent bearing area as having roughly half the capacity of a driven pile. However, the code considers drilled piles treated with the EHDE technique a direct “one for one” substitution for driven piles and allows higher values if the capacity is established by static load testing. Hundreds of projects have been completed in Russia using this technology to value engineer drilled pile projects. In several instances, the number of drilled piles installed was fewer than half of the number originally planned for due to the capacity increase that EHDE-treated piles provided.Drilled PilesIn drilled pile construction, the EHDE process creates a mechanical pressure wave that impacts the base and sidewall of a drilled pile shaft. Soft, poorly consolidated or loose soil is compacted by successive pulses of pressure created by electrical discharges. These mechanical impulses are made by inserting a discharge probe into the wet concrete slurry. A discharge across the tip of the probe creates the pulse that travels outward to the sidewall and base of the drilled pile through the incompressible medium of the slurry. The power pack ratings for equipment presently in use are 35 and 50 kJ (kilojoule).Each pressure wave strikes the soil, causing compaction and expanding the hole. Workers apply the pulses until the size of the hole stops increasing. They watch the slurry level during pulsing. When the level quits dropping, further soil compaction in the drill hole sidewalls and base is not possible. After the pulse process is complete, workers insert a rebar cage and the pile is finished.The process does not alter the soil mineralogy. The electrical discharge is internally grounded and does not arc to the sidewalls of the drill hole. Soil is not scorched or altered in any manner; it is only compacted by the pressure wave. This technique has been used in urban areas with no effect on electrical or electronic equipment."

Jan 1, 2009

By Andrea Gambi, Giancarlo Olivucci, Maurizio Lenzi

"In the paper a criterion for the evaluation of the sharing of the lateral loads in a piled foundation is presented. It relies on the the compatibility condition between the rotation of the rigid pile cap and the rotations of the pile heads, following in that the criterion suggested by the Eurocode 8 - Part 5. This assumption leads to an analytical solutions which allows to deal with the sharing of the lateral loads and moments by means of two main interaction parameters only. A sharing domain is also derived and it shows the role played by the eccentricity of the lateral load on the values of the axial forces and of the bending moments at the head of the piles.INTRODUCTIONIt is well known that the interaction among soil, piles and foundation is one of the most complex subject to deal with in Geotechnical Engineering. Its rigorous study needs to employ suitable finite element software nowadays available and able to take into account the non linear behavior of the soil as a continuum and the inelastic response of the structure. A deep insight to the topic of the sharing of the loads cannot obviously renounce to this approach.On the other hand it is a daily need of the designers to have at their disposal simple tools that allow to make preliminary evaluations of the basic equilibrium conditions. To this purpose many methods of analysis have been developed in the past to face the sharing of the loads in a simplified version. The present contribution follows this way trying however to introduce some improvements that leads to find a solution that satisfies both the equilibrium of the forces and the compatibility of the movements (Lenzi, Gambi, Olivucci, 2002). The proposed model allows to identify the basic parameters which govern the sharing of the lateral load and it allows to perform also parametric analysis and quick checks that may be useful in the design of the piles."

Jan 1, 2005

By Brandon M. Robinson, Osman F. Besler, Dominik Gaechter

With the increase in population over the last decade, and anticipated population growth over the coming years, Norway is making significant investments in the Country’s infrastructure. Part of this investment in development starts with the Intercity development project in South-East Norway, which is the largest transport project in Norway. The Intercity Development project consists of 270 km (167 mi.) of new doubletrack rail, capable of train speeds reaching 250 km/h (155 mph). The new stations are centrally located in the major cities, in South-East Norway, to provide the benefit to as many citizens as possible. The goal of the project is to reduce the increase in traffic, which is coupled with an increase in population, and reduce the travel times between the cities. The Intercity Development Project has an anticipated completion date of 2034. The Sandbukta-Moss-Såstad (SMS) project, part of the Intercity development, includes 10 km (6.2 mi) of new double-track railway and is situated on the Østfold Line, near the city of Moss, Norway shown in Fig. 1. The 10 km SMS-section covers three open stretches and two tunnels, including 630 m (2,066 ft) substructure for double-track railways on the open line at Sandbukta. The Moss tunnel is a 1720 m (5,643 ft) long tunnel from Sandbukta to Moss center, including a 420 m (1,378 ft) long concrete culvert. The new Moss station includes an 800 m (2,625 ft) long station area. The Carlberg tunnel is a 2350 m (7,710 ft) long tunnel from Kleberget to Carlberg, including a 200 m (656 ft) long concrete culvert.

Sep 8, 2021

By Takefumi Takuma, Hiroyuki Nishimura, Shigeru Kambe

"In order to achieve tubular pile driving with low noise and low vibration, the Press-in Piling Method has been adopted on many projects. The method utilizes reaction force derived primarily from previously driven piles to push in the next pile into ground. With attachments, the Press-in piling equipment can deal with hard soil as well as difficult site conditions. At West Toronto Diamond Rail Grade Separation Project in Toronto, Canada, the Press-in piling equipment drove more than 500 of 914 mm (36 inches) diameter tube piles in length of 12 to 25 meters (39 to 82 feet) to construct earth-retaining walls for railway grade separation. Myoshoji River Restoration Project in Tokyo, Japan drove some 600 of 1,000mm (39.4 inches) diameter tube pipe sections in length of 11 to 22 meters (36 to 72 feet) by the rotary Press-in piling equipment to increase the flood drainage capacity of an existing river in highly populated area of the city. Both projects exemplify the advantages of the method in urban settings.1. BACKGROUNDThe Press-in Piling Method was invented some forty years ago in Japan, where a very large number of construction projects were causing widespread construction pollution, especially by pile driving work in densely populated areas. The method has been providing solutions for piling projects which could not have been built otherwise due to the noise and vibration impact to the surrounding communities. The method can be used with various types of piles including sheet piles, tubular piles, concrete sheet piles and so on. With high pressure water jet and continuous flight auger attachments, the Press-in piling equipment can deal with dense sand, stiff clay, gravels, boulders and even soft rock without employing a different set of equipment."

Jan 1, 2015

By W. L. Chong

For a project located in Docklands Victoria, a high-rise development was proposed where the geology comprised soils of various compositions and consistencies to approximately 50m deep before being underlain by a siltstone bedrock. Due to the structural loads and spatial constraints, the majority of the foundation piles were designed to be socketed into the siltstone. Key factors in selecting the Continuous Flight Auger (CFA) technique as an effective piling solution are explained. These factors included structural and geological considerations, piling rig capabilities, pile testing regime to verify load performance and integrity, the extensive suite of construction quality controls and instrumentation records required while also achieving an appropriate piling budget and program. This paper also described how these factors underpinned the design approach of the final piling scheme. Critical aspects considered during construction and post-construction quality and pile testing records required to meet and satisfy the strict project piling specifications are also presented. The project adopted what may be considered the “best practice” in deep CFA piling. To the author’s knowledge, this project achieved the record for the deepest CFA piles in Australia where multiple piles to 53.8m deep were constructed.

Nov 1, 2022

By Benjamin B. Buensuceso III

Crosshole sonic logging (CSL) is a popular quality assurance and quality control method used to examine the concrete quality of cast-in place deep foundations, though the evaluation of the results is subject to certain limitations. One such limitation explored in this paper is the occurrence of false positives, where signal anomalies indicated by CSL test results are not necessarily indicative of imperfections in the foundation that could affect its performance. A case study of false positives evaluated in CSL records in a major infrastructure project in Metro Manila is presented in this paper. A detailed desktop evaluation and results from complementary high-strain dynamic load testing and low-strain pile integrity testing were used to evaluate the significance of the suspected false positive signal anomalies from the CSL test results. Recommendations for the proper interpretation and evaluation of CSL test results in Philippine practice, given the method’s limitations and examples presented, are also shared.

Sep 8, 2021

By Victor Li, Joley Lam

"INTRODUCTIONJacked piles are piles that are pressed into the ground, usually by hydraulic jacks. For this reason, jacked piles are also known as pressed in piles. Jacked piles are mainly used for the following applications.• Underpinning worksJacked piles have been commonly used for strengthening the foundation of existing structures. In pressing the pile into the ground, the hydraulic jacks will jack against existing pile caps or ground beams that support the structure or against a steel frame connected to the floor slabs or structural walls of the structure. The self weight of the structure provides the reaction force for pile jacking. Jacked piles used for underpinning works usually have lower design ultimate capacities, typically less than 2000 kN (225 tons).• New foundationsJacked piles can be used to support new structures. A heavy pile jacking machine is employed to provide the reaction force for jacking the piles into the ground.• Retaining structuresJacked piles can be installed at close spacings to form a retaining wall. For relatively large and easily accessible sites, the piles can be installed using a conventional pile jacking machine. For sites that are smaller and are more difficult to access, a more compact patented equipment called the Silent-Piler developed by Giken Seisakusho Co. Ltd. in Japan can be used.Jacked piles have several distinct advantages. The vibration and noise induced during pile jacking are minimal. Jacked piles are 100 percent proof-tested to a load level equal to the maximum applied jacking force. The pile jacking machine can also be treated as mobile kentledge for static loading test. In this article, discussion will focus on jacked piles used for supporting new structures.HISTORICAL DEVELOPMENTThe People’s Republic of China (PRC) is perhaps one of the earliest countries in which jacked piles were used as new foundations. Jacked piles had been installed in the PRC since the 1960s. The capacities of jacked piling machines used in the country are usually in the range of 3000 to 6000kN (337 to 675 tons). High capacity jacking machines with a capacity of 9000 kN (1000 tons), presently used by the construction industry in Hong Kong, were also manufactured in the PRC. There are also plans to produce machines with a capacity exceeding 10000 kN (1125 tons). It was projected by Wang (1999) that jacked prestressed spun concrete piles would become one of the most popular pile types in the PRC in the 21st century."

Jan 1, 2004

By Brian Wilson, Franz-Werner Gerressen

"Cutter Soil Mixing, also known as CSM, was developed in Europe as an alternate method of Deep Mixing to the more traditional single and multiple auger techniques, and brought to market by Bauer Maschinen GmbH (Bauer), towards the end of 2003. Initial development of the technique had been completed in a joint venture between Bauer and Bachy Soletanche. In 2004 the concept was introduced to the North American market. Continued development of the method and demonstration of its versatility, both in terms of applications and applicable soil types has seen a steady growth in the number of designs incorporating the approach, and contractors offering the technique. This paper provides a brief overview of the variety and size of projects and applications where the method has been adopted, discusses some lessons learned with respect to equipment operation as well as the improvements that have been introduced to the equipment, and briefly reviews the current state of practice, as well as some of the associated on-going research and development.BACKGROUNDCutter Soil Mixing (CSM) is a technique for deep soil mixing that was initially developed as a collaborative effort between Bauer Maschinen (Bauer) and Bachy Soletanche, but which ultimately resulted in the separate development of two somewhat different brands of CSM tool. The Bauer brand of CSM entered the European market in 2004, and was first promoted in the North American market in late 2004, with the first project starting in 2005. The Bachy Soletanche brand, sometimes referred to as “Geomix” was first marketed in Europe in 2005 and the first model introduced in North America in 2007.The development of the Cutter Soil Mixing technique utilized the experiences gained from Trench Cutter/Hydrofraise equipment, developing a technique that incorporates two cutting wheels rotating about a horizontal axis as opposed to the more conventional deep soil mixing approach which utilizes augers and mixing paddles rotating about vertical axes. Whereas the Trench Cutter/Hydrofraise technique excavates the soil from within a panel, and supports the open hole using a bentonite slurry, the CSM technique cuts and displaces the soil whilst pumping a slurry/grout directly into the soil through a port located between the wheels. The combination of cutting the soil while introducing an appropriate volume of slurry effectively fluidizes the column of soil around and above the cutter head. While this process achieves a high degree of mixing, even on the downward cutting stroke, thorough in-situ mixing typically occurs on the withdrawal stroke, when most of the slurry is added."

Jan 1, 2015