Search Documents

By G. Bartolacci, G. Couture, Levasseur. B., A. Lockhart, D. Nathan

"Pulp and froth zone characterization in a flotation circuit to improve transport of valuable minerals remains a challenge. Even though some significant breakthroughs have been made in the development of collectors in terms of selectivity, the control of gangue drainage is still the main bottleneck to achieve the production of a clean concentrate.Over the last decade, COREM’s team has been working on technologies to improve the selectivity of flotation circuits by tuning their hydrodynamic conditions using online instruments such as the bubble viewer, Jg sensor and gas hold-up. As part of its research program, COREM also developed the half-life column that establishes the relationship between the collection zone (bubble-particle attachment) and the cleaning zone (foam) of a flotation machine. In recent years, COREM has continued the development of the prototypes to make them more robust and improve the accuracy of their measurements.Recently, these hydrodynamic instruments were installed in an industrial process at Raglan Mine in order to diagnose and control the impact of hydrodynamic parameters versus the recovery and the quality of the Ni concentrate produced. Sampling campaigns of hydrodynamic parameters demonstrated that froth height could be optimized in order to increase recovery and quality of the concentrate at the same time. The specific effect of the froth height impacts both the pulp and the froth zones. Along with the impact on the drainage of the concentrate, it was observed that froth height also contributes to enhance the collection of particles in the pulp leading to an increase in metallic units.IntroductionOnce the particles of the minerals of interest are attached to the air bubbles injected in the pulp, the flotation process is driven by air dispersion parameters and froth properties. The pulp is usually responsible for the collision between air bubbles and hydrophobic particles of interest while the froth zone aims to upgrade the selectivity of the particles floated through drainage of the unwanted hydrophilic particles. Over the last four decades, flotation hydrodynamics has been extensively studied. Superficial gas velocity (Jg), gas hold-up (eg), Sauter mean bubble diameter measurements (d32) and bubble surface area flux (Sb) are among the most assessed parameters in flotation plants worldwide either to quantify the gas dispersion parameters or to optimize them (Fournier et al., 2015). McGill University has developed several sensors able to measure these parameters at industrial scale (Tavera et al., 1996; Finch et al., 1999; Chen et al. 2001)."

Jan 1, 2017

By P. P. Rosario, D. M. Maijer

The primary crusher is a key component in the comminution process applied in open pit mines. A collaborative research project between the University of British Columbia and Highland Valley Copper (HVC) was conducted aiming at understanding gyratory crusher liner wear in the overall context of the crushing process. This paper presents an analysis methodology applied to data collected using a laser-based tool for assessing wear in gyratory crushers. Data from the wear measurements was correlated with crusher production information such as current draw and throughput. As a result of the knowledge developed during this work, an innovative way to evaluate crusher liner profiles was created and new mantle profiles were designed. This led to a reformulation of HVC’s standard liner management policy with a resulting estimated annual savings of 13% in total crusher liner cost and a 15% reduction in liner replacement downtime.

Jan 1, 2006

By Ruy L. Rodrigues

Vale is in the early stages of commissioning its Onça Puma nickel operations. The project is meant for the production of 58,000 tpa of nickel contained in ferro-nickel, substantially contributing to the company?s vision to achieve world leadership in the nickel business. Mineral resources will be exploited from the homonymous deposits in the Midwest of state of Para, Brazil ? some 100 km southwestwards from the company?s Carajás iron ore properties. Resources as of 83 Mt at 1.73 % Ni will sustain a mine life of approximately 40 years. The property was acquired in late 2005 and Vale has since extended the engineering studies and proceeded with the implementation. Nickel will be mined from saprolitic ore at a rate of approximately 10 Mtpa (ore plus waste) in early years ? ramping up to some 15 Mtpa 7 years later ?, to feed the plant at a rate of 2.5 Mtpa. The process uses conventional RKEF (Rotary Kiln Electric Furnace) pyrometalurgical route whereby the ore is homogenized, calcined in rotary kilns, melted in electric furnaces and further refined to ferro-nickel. The plant has been designed and constructed applying the latest available technology, aligned with Vale?s vison to exceed the highest existing standards for environmental control, health and safety and productivity in the industry. Total investments in these operations are anticipated to correspond to USD 2.3 Bi and will materially contribute to the regional development and well being of the nearby communities and other stakeholders.

May 1, 2010

By F. Halverson

"The theory of flocculation usually is in a state of flux, involves many diverse phenomena, and is complex and sometimes contradictory in details. Instead of attempting a general discourse, I shall discuss selected observations made at our Stamford Laboratories, which impinge on theoretical aspects in two somewhat distinct areas of flocculation. Since some of you many not be familiar with flocculation, and :.n order that we all attach the same meaning to the jargon used, I first would like to review briefly a generalized picture of what goes on.Assume we have a suspension of particles in water, with a distribution in the sizes of particles. The surfaces of the particles interact to some extent with the water--· tending to alter the extent of hydration, may generate some ion exchange, all being somewhat variable with time--developing a surface condition which is very complex in details. We refer to this suspension as the ""substrate.""In the usual situation, if the suspension is allowed to stand quietly, the large particles settle out first, with somewhat smaller particles settling more slowly, and then there is a portion of very fine material which takes a long time or doesn't settle out at all. This resistance to settling t~ the very fine particles results from many factors, but all relate back to the size and density of the particles, to their surface properties, and to the other components in the aqueous suspending medium."

Jan 1, 1978

By L. W. Vigrass

Porous and permeable rocks deeply buried in sedimentary basins contain immense volumes of hot water with the potential to supply low-grade heat energy. A part of Canada with sizeable potential for low-grade geothermal energy is the northern Williston Basin of southern Saskatchewan. In this region, the University of Regina has conducted a geological study investigating the feasibility of producing large quantities of warm water suitable for space heating in the Regina - Moose Jaw area. The study has shown that the most favourable geothermal reservoirs are in the Basal Clastic Unit (Cambrian Ordovician), which, at an approximate depth of 2,000 metres has predicted temperatures of 71°C to 74°C. We anticipate sustainable flow rates from these reservoirs of 100 to 300 ms/hr. The water contains about 150,000ppm of total dissolved solids, mostly sodium chloride. It is anticipated that the sulphate content will be 3,000 to 6,000 ppm, that the dissolved oxygen and hydrogen sulphide content will be small, and that the waters will be neutral to slightly alkaline. It is anticipated that the piezometric level will be 46 m below the ground surface for reservoirs in the upper part of the Basal Clastic Unit and 141m below the ground surface for the lower reservoirs of the unit. Plans are to build a low-grade geothermal research, testing and demonstration facility at the University of Regina. To be a practical demonstration, the facility will have to handle very large volumes of water. Because of high salinity, the water will be re injected into a subsurface reservoir. We do not anticipate insurmountable problems because of salinities or as a result of corrosion provided that the waters are not aerated during handling

Jan 1, 1979

By V. Balakrishnan, A. Hewitson

"The Kudremukh Iron Ore Company Limited, a government of India enterprise, has constructed iron ore mining, crushing, handling and concentrator facilities at Kudremukh, in southwest India. Concentrate produced is pumped 65 km to dewatering, storage and ship-loading facilities which were built at the same time at the sea port of Mangalore.A computer-based distributed process control system was implemented for all operations at Kudremukh and to interface with and monitor the Mangalore plant.The control system is examined from various standpoints, beginning with a description of its architecture, method of process input/output connection, and major hardware items.Software considerations and process applications are then looked at, with a review of the integration of the computer vendor's system software with user-developed applications programming. A control example of crusher operations is provided.Following the descriptive segment is a discussion of the design considerations and decision factors involved in the implementation of such a system considering the type of process and the remote nature of the installation site. It ends with a review of actual operating experience and conclusions regarding both this system and future similar applications.ScopeThe following is a discussion of the computer-based process control system applied for the Kudremukh Iron are Company Limited's ore handling, concentrating and shipping facilities located in South India.A general description of the process and plant equipment will be followed by an examination of the control system from the points of view of hardware and signal flow, software requirements, design considerations, implementation logistics and operating experience. Conclusions will be drawn concerning this and future computer applications."

Jan 1, 1984

By C. Larsen, I. Orford, L. Strah, M. Renaud, P. Radziszewski

"An AG/SAG mill was commissioned at the Brunswick mine concentrator in October 1998. This paper discusses the original shell top hat liner design for the bi-directional AG/SAG mill, observed liner wear, subsequent liner design modifications, and benefits.The original liners were chrome-moly steel Norsteel with rubber grates and rubber-lined pulp lifters. The design was based on experiences of other AG/SAG mills and recommendations by the liner supplier, Norcast. Liner design modifications were made in an iterative fashion after observing the wear rate profile of the liners; over ten liner sets were implemented. Shell liner design improvements were supported by a design of experiments approach in conjunction with discrete element method (DEM) charge motion simulations. Design optimization took into account lining costs and impacts on operating performance. The team approach to the liner design improvements process is described with emphasis on the application of the design of experiments. The liner wear history and mill operating performance are presented."

Jan 1, 2005

By W. R. Green, B. W. Barde

"Geological exploration involves the collection and analysis of a wide variety of information. A basic problem in interpretation is to determine the interrelationship s of the different data. A number of statistical methods can be applied to this problem, provided that subsets of data can be selected.We have recently developed a set of interactive computer programs which provide the cap ability to quickly examine a large set of data, and may be used by people with little previous computer experience. There are two main stages in using this system. First is selection of subsets of data , by applying various tests on the values of given items. This includes matching specific entries in descriptive fields, and minimum - maximum tests on numeric fields. The second stage is basic statistical analysis and data display , including histograms, 2-D scalier plots, probability (cumulative frequency) plots, and correlation matrices. All output can be viewed on a computer terminal, and important parameters changed to produce the most effective display for use in interpretation.This system has been applied to a number of different exploration problems. An example was the determination of the nature and extent of mineralization of a gold prospect in the Queen Charlotte Islands, from drill-hole data. With the aid of the computer programs , a mineralized zone was defined, and locations for further exploration identified."

Jan 1, 1984

By K. Adham, C. Lee

Over the last forty years, a number of specific fluidized bed applications in nickel extraction have been developed for commercial use. Five important processes have gained particular acceptance, namely, sulphide ore roasting, nickel sulphide (matte) roasting, nickel oxide reduction, laterite ore pre-reduction, and nickel chloride pyrohydrolysis. These applications involve different feed materials and process conditions, however, all benefit from fast reaction kinetics and high heat and mass transfer rates in the fluidized bed reactors. They have been studied, tested, and implemented by various nickel producers, who have published their results in many papers and patents. This paper examines the design issues surrounding the application of fluidized bed technology to the above nickel processes. Based on the available data in the open literature, computerized process modelling is used to provide generic flowsheets that illustrate the key features of each process.

Jan 1, 2004

By Patrick R. Stephenson

The current version of the JORC Code was issued in 2004 and since that date the Australian Securities Exchange, in collaboration with JORC, has issued a number of companies? updates to provide guidance on various reporting issues. An interim review will be undertaken during 2010 to meld these updates with the current 2004 Code. This will be followed by a full review during 2010/11 covering all aspects of the Code and focusing particular attention on: ? clauses / guidelines relating to Exploration Results1, exploration targets and the reporting of historical estimates; ? issues relating to the Public Report2, including definition, the requirements for Competent Person sign-off, level of disclosure and mandatory requirements; ? guidance on techniques to quantify resource / reserve estimation uncertainty; ? the level of study required to convert Mineral Resources to Ore Reserves, and disclosure of prices and economic factors; ? expansion of the requirements for reporting of marketable material for bulk commodities; ? the use of language and tone that anticipates new and emerging technologies and techniques for the qualitative and quantitative measurements of data; and ? linkages to valuation and the valuation code (The VALMIN Code). Although the Canadian and Australian reporting regimes for public statements on Exploration Results, Mineral Resources and Mineral (Ore) Reserves are similar in intent and coverage, they differ in detail, sometimes substantially. Canadian requirements are generally more wide-ranging and prescriptive than Australian requirements, including in the need in many situations to publicly lodge a Technical Report, a requirement that does not exist in Australia. Australian-listed companies seeking to list in Canada, and Competent Persons seeking to act as Qualified Persons in Canada, need to ensure that they are fully conversant with Canadian regulations and how they differ from those in Australia.

May 1, 2010

By R. Le Houillier, M. Nagamori, A. J. Plumpton

"Asbestos tailings are a typical serpentine, hydrated magnesium silicate, consisting primarily of antigorite and a few per cent of unrecovered fibrous chrysotile. Serpentine has unique thermal properties in that dehydroxylating calcination at 600 to 700°C can yield an amorphous structure in which most of the magnesia is liberated from the original bond with silica and thereby rendered chemically active. The amount of activated magnesia can be quantified by selective leaching with a weak acid such as acetic acid. Many wet processes have been proposed to extract magnesium values from calcined or natural serpentine by means of various acids and their ammonium salts. However, the only commercial utilization of serpentine today is found in dry processes such as the production of fused magnesium phosphate fertilizer .The present paper reviews the physical chemistry of the dehydroxylation of serpentine and also various wet and dry processes in order to provide a general view regarding the chemical transformation of asbestos tailings.IntroductionAsbestos fibers occur as chrysotile, a serpentine polymorph. More than nine tenths of mined asbestos ores consist of massive non-fibrous serpentine, primarily the polymorph antigorite, which is discarded as tailings after fiber extraction. For many decades, Quebec has been a world leader in the production of asbestos fibers. As a result, colossal tonnages of serpentine have accumulated in the Eastern Townships'!'. Serpentine minerals are found in large deposit s throughout the world, and significant research efforts have been made, particularly in Japan and the USSR, mostly in attempts to extract magnesia or silica values therefrom.The chemical composition of serpentine (chrysotile and antigorite) may be ideally expressed as Mg3Si2Os(OH). which corresponds to 43.7% MgO and 43.3% SiO2. Natural serpentines often contain a few per cent of Ni-bearing magnetite and other impurities, and therefore the contents of MgO and Si02are both about 40% or lower.Serpentine (hydrated magnesium silicate) is virtually insoluble in weak acids. However, when dehydroxylated under controlled conditions, ' it decomposes to an amorphous state in which magnesia and silica are isolated and chemically active. The magnesia so activated is readily soluble in weak acids. This unique characteristic of calcined serpentine, first discovered in 1942,, has since attracted the attention of innumerable researchers, whence many processes have been proposed."

Jan 1, 1980

By W. L. Thayer, K. A. Jonasson, R. D. Coleman, J. D. Hazlett, C. E. Capes

"Loss of coal fines in reject slurries limits the yield of coal cleaning operations. Difficulties in handling fines also limit the extent of physical cleaning in treating coals with finely-disseminated impurities. Selective oil agglomeration allows even extreme fines to be processed and offers some novel approaches for coal cleaning and utilization.The oil agglomeration process for the recovery and beneficiation of fine and ultrafine coal has now been commercialized by the Chemical Engineering Section/Chemistry Division of the National Research Council (NRC). This paper describes these activities to apply oil agglomeration and related fine coal technologies on an industrial scale. Pilot plant and large scale results are described, as well as aspects of agglomerate utilization in both wet and dry form."

Jan 1, 1988

By P. A. Hacquebard, M. P. Avery

"Gondwana coal deposits are widespread and are known to occur in four continents. They are present in Brazil, India, South Africa, and Australia. From coal petrographic examinations and a detailed literature survey, it is interpreted that Gondwana coals are present also in Canada and the United States. Laurasia, or Northern Hemisphere, coals occur in the United States, Canada, and Europe. They form the main coal producing fields of the world. Megascopically, Gondwana coals have a uniform, micro-banded appearance, with a dull lustre; Laurasian coals are bright and have distinct bands of vitrain and clarain. Petrographically, Gondwana coals, compared to Laurasian coals, are lower in vitrinite, but higher in inertinite, particularly in semifusinite. Mineral matter averages 16% in Gondwana coals and 5.7% in Northern Hemisphere coals.Gondwana coals are characterized by thick seams that terminate through lithification (Versteinerung), whereby coal passes laterally into shale. Laurasian coal seams are thinner and terminate by splitting and digitation.Vitrinite/inertinite ratio data indicate deposition of the Gondwana coals in dry marshes under strong oxidizing conditions. The Laurasian coals originated in wet marshes in a reducing environment. As deduced from fossil plants and fossil spores, temperate and near arctic conditions apply for the Gondwana coals. A tropical and subtropical climate is indicated for the Laurasian deposits. The Gondwana coals were formed under allochthonous conditions. They derived from vegetation that drifted into the peat bogs. The Laurasian coals are autochthonous and originated from vegetation that grew and was buried in the peat bogs. The Gondwana coals are Late Carboniferous and Early Permian. The Laurasian coals are entirely Late Carboniferous."

Jan 1, 2004

By J. M. Simard, S. Morissette, P. Coursol, P. Mackey

A new, powerful model is presented that focuses on plant logistics and scheduling aspects of the smelting, converting, fire refining and casting operations at the Horne smelter. This plant complex is the largest custom copper smelter in North America. It handles a wide range of feeds and utilizes a number of proprietary continuous and batch technologies that require good scheduling in order to maximize plant capacity and efficiency. The present model was developed by Xstrata Process Support, in collaboration with the Horne smelter, and uses the Arena® software to evaluate the impact of a number of plant variables on the annual copper capacity of the plant. Model development was carried out by Xstrata Process Support, in collaboration with the Horne smelter, through the effective combination of process chemistry knowledge and detailed knowledge of the plant operation (including all material flows and transfers, as well as information such as operating on-line times, plant stoppages and also scheduled and unscheduled maintenance activities). A number of case studies were then examined, including the impact of anode furnace and casting cycle times on annual copper capacity and the impact of a one-crane mode of operation in the converter aisle, which normally operates with two cranes in service. The model predictions were found to match actual plant results very well. The present modelling of plant logistics and the scheduling aspects were found to add important dimensions at the plant with regard to projections of the real-life plant capacity. As demonstrated in the present case, this type of model and application can have a significant impact on optimizing operations at a given plant. This impact is particularly important in the current market environment, where emphasis is on maximizing plant output and lowering costs. These models can help yield the easily obtained gains that are clearly desirable in these times. Xstrata Process Support has developed Arena models for other operations and is available to explore new applications for a win-win situation at other plants, including mines and concentrator operations.

Jan 1, 2009

By Constantin D. Pitis

Similarly to notions of constant capital/expenses in business or magnetization power for electric motors an energetic base load (E0) is always necessary to set up a mining process. Denominated as ?non-productive energy? or base load, (E0) is a constant component of the entire energy consumption of the process, while another component the ?productive energy? (Ep) is variable, being function of the production/throughput (M). By using these new concepts, the author creates an energetic model proposing a new method of assessing changes in mining processes (throughput) that can reveal possible energy savings (DSM component) or energy losses. Proposed mathematical model of assessing (E0) and energy savings by using ?Marginal Energy Usage Index? (MEUI) enables creation of historical benchmarks and direct on line energetic (efficiency) assessment of mining processes and/or equipments. The paper analyses the case of assessing possible energy savings that can be obtained by: ?? Improving efficiencies of various equipments (by retrofit) ? reducing E0 ?? Improving the process control or other process changes ? reducing Ep ?? Monitoring persistence of the adopted Energy Conservation Measures (ECMs). For the new plant design, the proposed method enables prediction of Customer Baseline in various mine/process configurations. The method could become part of a ?preventive action? in design process by offering a reliable tool of assessing additional financial effort (Incremental cost) when choosing various higher efficiency equipments and/or processes.

Oct 1, 2009

By K. J. Fair, H. W. Smith, D. R. Francis, J. M. Toguri

"Bench-scale batch milling and screening tests were carried out on secondary aluminum dross 10 produce an aluminum concentrate. To complement these tests, an analysis of a commercial plant was also performed by sampling dross at various stages in the plant's milling and screening circuit. These studies have indicated that benefits of increased capacity, grade and recovery of aluminum metal can be realized by addition of screens before the ball mill, longer grinding period and by grinding the smaller size fractions more efficiently.To test the predictions, a plant test was performed on the milling of100tons of secondary dross. The recycling of the large size fraction (+1/8 in.) of aluminum dross through the impact mill rather than through the rate limiting ball mill resulted in a comparable aluminum grade. The ball milling of the _1/ 8 in. + 10 mesh size gave a dross grade of71% AI. A lower feed rate to the ball mill resulted in a higher final grade. With minor modifications, secondary dross can be processed in 22% of the time it takes with the present circuit without a sacrifice in grade.IntroductionSecondary aluminum dross is a mixture of metallic aluminum, aluminum oxides and salts (alkali halides). Any comminution process deforms or slowly grind s the malleable metal phase and reduces the size of the friable, brittle, oxide-salt phase relatively fasterr(1).The milling of aluminum dross is performed to upgrade the metallic aluminum fraction. Figure I shows a flowsheet for the milling of secondary dross as presently practised at Metals and Alloys Co. Ltd., Toronto, Ontario. At point A, large acceptable grade material is hand picked for refurnacing, the unacceptable off-grade material is sent to the sweat furnace and the remaining, + 2 in. fraction is recycled through the 3.9 ft by 4.1 ft impact mill. For simplification, three ball mills are shown. However, in reality there is only one, a 5 ft by 10 ft ball mill used in a semi-batch mode. The 2 in. + 3/8in. and 3/8 in. + 10 mesh products are remilled in the ball mill. The -10 mesh material is discarded as waste."

Jan 1, 1987

By N. Romani, R. Provost

"Commissioning of a circulating dry scrubber (CDS) plant was recently completed at an existing facility in Québec, Canada. The CDS plant treats the sulphur dioxide off-gas emitted from rotary kilns in order to meet increasingly stringent environmental requirements. This installation enables the existing facility to reduce their sulphur emissions by over 90%.Proper planning of the different commissioning stages and staffing an integrated team are the most important factors required for a successful plant start-up. A strong Operational Readiness plan must be in place as early as the start of construction in order to ensure a smooth transition from commissioning to operations. Plant performance can meet or exceed performance criteria within the required timeframe if the proper group dynamic and good communication is established between construction, commissioning and operations teams.The road blocks encountered are often from systems that one assumes will operate without trouble such as air-conditioning, or design assumptions that were taken years earlier in feasibility process stages, namely the capacity of existing systems that will connect the new plant to the existing facilities. The challenges associated with rectifying these issues in addition to the requirements to properly start-up and operate a new plant without impacting production are great, and it is imperative to have the necessary resources to react quickly to any problems.IntroductionCommissioning of a circulating dry scrubber (CDS) plant was recently completed at an existing facility in Québec, Canada. The CDS plant treats the sulphur dioxide off-gas emitted from rotary kilns in order to meet increasingly stringent environmental requirements. This installation enables the existing facility to reduce their sulphur emissions by over 90%.The CDS ProcessA general overview of the CDS process is presented in Figure 1 below. The combined, de-dusted off-gas from multiple kilns is sent to the CDS, which acts as an entrained fluid bed, where the gas is contacted with a water mist, re-circulated solids and hydrated lime. The SO2 from the gas stream and the available calcium hydroxide (Ca(OH)2) from the hydrated lime dissolve in the water and react to ultimately form calcium sulphites and gypsum. The solid residue (referred to as CDS residue), is the primary by-product of the process."

Jan 1, 2016

By Benedetto Corain

The production and dispersion of metal nanoclusters onto inorganic supports and amorphous carbon rest on well consolidated technologies belonging to the realm of industrial catalysis and of basic catalysis research (1). In spite of the existence of a variety of specific synthetic strategies, their very rationale relies on three main approaches i. e.: A: precursors of both the metal nanoparticles and of the relevant supports (or the support itself) are intimately mixed (even let to react) at ambient conditions and then thermo-reduced according to very controlled protocols (2); B: precursors of metal nanoclusters are let to be adsorbed onto suitable supports from the gas or liquid phase and subsequently thermally decomposed (3); C: metastable size-controlled metal nanoclusters are previously generated in a liquid medium and subsequently transferred onto pre-formed support particles (4). The production and dispersion of metal nanoclusters onto organic soluble supports is also a rather well documented academic praxis (5, 6, 7, 8) able to provide e.g. size-controlled Au0 nanoclusters of 4.4±1.7 nm (5). Our group started in 1997 developing (9) an innovative approach to the synthesis of metal nanoclusters dispersed inside insoluble, albeit accessible (see below) mechanically robust gel-type resins (10), which procedure was tested so far on palladium metal. Metal ions are previously dispersed upon ion-exchange inside of the polymer framework, followed by chemical reduction and by the aggregation of born metal atoms into nanoclusters, the size of which is templated (11, 12) by the three-dimensional intercommunicating meshes that build up the overall polymer framework (Figure 1).

Oct 1, 2003

By Norman O. Lotter, Lori Kormos, Greg J. Wilkie, Peter J. Whittaker, Johannes S. Stickling

"Assessment of opportunities to improve mineral processing performance in existing concentrators and in describing undeveloped orebodies is key to improving the business case of a mining company. This assessment has traditionally been performed using the distinct and separate inputs from Mineral Processing and Mineral Science.More recently, Process Mineralogy has been used to integrate these two disciplines. This trend has been driven by the need to develop and process more challenging ore deposits, and has been assisted by the availability of modern automated instruments. Together with the acquisition of a QemSCAN (Quantitative Evaluation of Materials by Scanning Electron Microscope) from CSIRO in Australia, and with the use of a supporting SEM with EDX / WDX capabilities and an XRD, the development of Process Mineralogy at Falconbridge commenced in 1997.The sampling challenges in presenting a QemSCAN with representative sample material at the polished section level are significant, but have been effectively addressed. The full description of this aspect is beyond the scope of this paper.It is shown that, by use of this approach, the set nature of an orebody can be best exploited with selected flowsheet changes in a concentrator which address the generic characteristics of the orebody. In this way, the flowsheet provides a process that more effectively fits the mineral processing requirements of the ore. This leads to clear and tangible improvements in grade and recovery."

Jan 1, 2002

By C. Stapel, AA Groningen, R. J. De Meijer

"In recent years the Environmental Research Group of the KVI has been developing a number of radiometric techniques that may be employed in mineral sand exploration. These techniques involve: radiometric fingerprinting for assessing sand provenances and mineralogical composition; thermoluminescence for dating and provenance determination of sediments; a towed seabed detector to map seafloors for radiogenic heavy minerals and assessing heavy mineral volumes; and simplified transport mechanism models to explain and predict heavy mineral concentrations.All techniques exploit the property that heavy minerals as a group contain concentrations of naturally occurring uranium and thorium that are a hundred to a thousand times higher than in light minerals. In this paper the physics of a number of methods will be described together with a number of results. Based on these results potential applications to mineral exploration and mining are discussed."

Jan 1, 1994