Search Documents

By W Zhu, J H. Zhao, H Ma

The permeability coefficient is an essential parameter for the study of seepage flow in fractured rock mass. This paper discusses the feasibility and application value of using readily available RQD (rock quality index) data to estimate mine water inflow and grouting quantity. Firstly, the influence of different fracture frequencies on permeability in a unit area was explored by combining numerical simulation and experiment, and the relationship between fracture frequencies and pressure and flow velocity at the monitoring point in fractured rock mass was obtained. Then, the stochastic function generation program was used to establish the flow analysis model in fractured rock mass to explore the relationship between flow velocity, pressure and analyse the universal law between fracture frequency and permeability. The concepts of fracture width and connectivity are introduced to modify the permeability calculation formula and grouting formula. Finally, based on the on-site grouting water control case study, the rock mass quality index is used to estimate the mine water inflow and the grouting quantity. The results show that it is feasible to estimate the fracture frequency and then calculate the permeability coefficient by RQD. The relationship between fracture frequency and RQD and the relationship between structure surface frequency and permeability follow an exponential function. The calculation results are in good agreement with the field monitoring results, which verifies the rationality of the calculation method. The relationship between the rock mass RQD index and the rock mass permeability established in this paper can be used to invert the mechanical parameters of the rock mass or to evaluate the permeability and safety of the rock mass, which is of great significance to the prediction of mine water inflow and the safety evaluation of water inrush disaster management.

Nov 29, 2022

By S H. Algie, D P. Taplin, S G. Doig

"Suboptimal performance of clusters of hydrocyclones (cyclones), relative to the performance of the individual cyclones that comprise the cluster, is a common phenomenon. The primary cause is well known: uneven distribution of the slurry feed into the individual cyclones. The direct result of uneven distribution is that each cyclone in a cluster performs somewhat differently. Hence, some, if not all, of them do not work at their intended operating points, and the classification is not as sharp as intended. The impact on grade, recovery and milling efficiency will vary depending on the duty of the processing circuit, but the most immediately apparent consequence of uneven distribution is a difference in wear rates in the individual cyclones; this exacerbates the problems of unequal performance of the individual cyclones. In severe cases, and as differential wear proceeds, flows from the individual cyclones may become visibly different. Uneven distribution, once the phenomenon was identified, was seen to be a significant issue in the high-solids hydrocyclone cluster in the ball mill recycle section of Evolution Mining’s Edna May Operation (EMO, Westonia, Western Australia) gold processing plant. In 2012, a FloCEP® hydrocyclone feed distributor system was installed to alleviate the problem. Over the next four years of operation, this innovation has proven its value in the metallurgical and maintenance areas. Individual cyclones now wear at the same rate, greatly reducing the need for operator intervention, as well as increasing overall plant availability through minimising unplanned maintenance. The costs of the installation can be justified by savings in maintenance alone, though the greatest value, as is described in this paper, is in allowing the plant to produce consistently closer to its operational design limits. The FloCEP® system is a low maintenance, readily installed retrofit, based on two patented devices that are combined with complementary proprietary design methodology allowing customisation for specific flow rates and slurry particle properties. Together, these devices produce and distribute a pseudo-homogenous slurry flow without moving parts.Citation:Taplin, D P, Doig, S G and Algie, S H, 2016. Experience with FloCEP® Slurry Flow Conditioning at Evolution Mining's Edna May Operation, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 251–260 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

The first mining in Western Australia probably commenced some 40 000 years ago when Aborigines arrived and began quarrying stone for tools and weapons, and ochre for decoration. The earliest documented mining by European settlers took place in 1850 on a small lead vein in the bed of the Murchison River, reported by the explorer A C Gregory. However, it was the discovery of gold in the Kimberley region in 1885 that first drew wider attention to the State's mineral potential.

Jan 1, 1992

By H F. Yu, S Ueda, J Diao, W F. Gu, Y Sasaki, H Qin

The main reason for the underutilisation of steelmaking slags is their instability, which is influenced by their complex phase structure. Recycling and sustainable steelmaking slag face challenges due to the presence of magnesium oxide (MgO), a crucial component in steelmaking slag. This study investigates the phase evolution of steelmaking slag during the cooling process with different MgO contents, using high-temperature experiments and FactSage™ software, ver 8.1, (by Thermfact/CRCT and GTT-Technologies) thermodynamic equilibrium calculations. X-ray diffraction (XRD) and scanning electron microscope - energy dispersive x-ray spectroscopy (SEM-EDS) analyses identified main phases in steelmaking slag, including Ca2SiO4 (C2S), RO (MgO-FeO solid solution), Ca2Fe2O5 (C2F), and Ca3SiO5 (C3S). The study reveals that RO phase increases as the MgO content increases. C3S precipitates from steelmaking slag with a 12 mass per cent MgO content at a reduced temperature of 1400°C. It is important to note that C3S remains in the steelmaking slag even after slow cooling. This may be due to the substitution of Ca2+ in C3S by Fe2+ and Mg2+ ions. Intriguingly, the precipitation of f-CaO in steelmaking slag with 10 mass per cent of MgO content occurred after one year, while there was no manifestation of f-CaO precipitation in the steelmaking slag with 12 mass per cent of MgO content even after one year. This discrepancy suggests a potential stabilising effect of an appropriate amount of MgO in steelmaking slag. However, it is crucial to emphasise that this inference lacks supporting data, necessitating further research to validate this hypothesis. The significance of this work is in uncovering the complexities of steelmaking slag behaviour, providing essential insights for optimising recycling processes. The research sheds light on the factors that influence the phase composition and stability of steelmaking slag, contributing to the utilisation of steelmaking slags, promoting environmental sustainability, and enhancing the overall efficiency of metallurgical processes in the current industrial landscape.

Jun 19, 2024

By W Zeng, D Walker, D Cai, E Baafi

"The efficiency of the truck-shovel haulage system is significantly influenced by the truck fleet size. A discrete event simulation model with 3D animation has been developed to estimate the productivity of a truck-shovel network system, shovel efficiency, truck cycle time, truck utilisation and the optimal fleet size. The simulation model considers the dynamic variability of traffic conditions and also the truck as an individual entity. The resulting truck cycle time was found to be realistic and thus providing a better tool for strategic mine planning.Citation:Zeng, W, Baafi, E, Walker, D and Cai, D, 2016. A 3D Discrete Event Simulation Model of a Truck-shovel Network System, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 265–273 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

By S Utili, A Agosti

The Overall Slope Angle (OSA) of pitwalls plays a crucial role in the financial return of an open pit mine. In current practice, pitwall profiles are designed to be planar in cross-section within each rock layer, ie the profile inclination across each layer tends to be constant. A new slope design software, OptimalSlope, has been recently proposed to determine the geotechnically optimal profile shapes for the pitwalls of mines. OptimalSlope seeks the solution of a mathematical optimisation problem where the overall steepness of the pitwall to be designed is maximised for an assigned stratigraphy, rock properties (unit weight and strength) and Factor of Safety. The geometry of the benches is provided as input to OptimalSlope. The results obtained so far on three mine case studies in isotropic rock masses (Utili et al, 2022; Agosti et al, 2021a, 2021b) show that optimal profiles are up to 5° steeper than their planar counterparts – ie the planar profiles exhibiting the same FoS – leading to realising significant saving on waste rock and as a consequence Net Present Value increments and carbon footprint reductions. OptimalSlope algorithms have been modified to deal with anisotropic rock masses characterised by direction dependent shear strength. In the paper, the case of rock masses in banded iron formations (BIF) is tackled. A data set of anisotropic rock shear strengths typical of Western Australia is considered. The Snowden modified nonlinear model was employed to characterise the anisotropy of the rock mass shear strength. From the OptimalSlope simulations performed emerges that optimal pitwall profiles can increase significantly the Overall Slope Angle in comparison with planar profiles featured by the same Factor of Safety. LEM stability analyses of all the profiles were also performed by Rocscience Slide 2 to independently verify the FoSs of the optimal profiles obtained.

Nov 29, 2022

By J Walshe, G Duclaux, L A. Fisher, R Hough, J S. Cleverley, M F. Gazley

Characterisation of hydrothermal gold systems across multiple scales is increasingly important for our understanding of ore deposit genesis and for targeting new mineralisation. Published work on multiscale mineral system exploration focuses either on applying a single technique across scales or on incorporating a series of techniques across a limited scale range. Typically, these studiesÆ spatial scales vary from crustal to deposit-scale and have successfully linked the distribution and shape of major orebodies to fault systems or varying lithostratigraphy. But, is this scale small enough to answer fundamental questions about the relative timing, processes interactions and mechanisms involved in the formation of ore deposits? We illustrate the potential of a deposit to microscale study, using the Plutonic Gold Mine in Western Australia as an example, to better understand hydrothermal gold systems. Using an integrated approach combining lithological and alteration logs, various geochemical data set, meso- to microscale structural and textural observations and spatial data assimilation, we have revisited the fundamental processes involved in the formation of this significant gold deposit.CITATION:Duclaux, G, Hough, R, Gazley, M F, Fisher, L A, Walshe, J and Cleverley, J S, 2013. A multiscale approach to hydrothermal gold systems - unravelling mineralisation processes at the Plutonic Gold Mine, in Proceedings World Gold 2013 , pp 95-98 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

Throughout the study phases (scoping, prefeasibility and feasibility) of new mining projects one is forced to work with and make predictions based upon limited date obtained from diamond and reverse circulation drill holes. These data are extrapolated to determine how much of the valuable metal is present in the ground, how it can be recovered it and the efficiency of this recovery. Mining methods to extract the ore are investigated with forecasts made regarding excavation stoping stability and performance in an attempt to optimise production. Extraction and use of rock mass data for use in characterising the mechanical behaviour of the rock mass is no exception. One often relies heavily upon the use of empirical charts developed over many years on hundreds of case histories based upon rock mass characterisation schemes. This is largely successful and indicative of what one might expect. However specific site characteristics can always play a significant role, and are not necessarily apparent in diamond drill core. Feasibility studies for the Favona orebodies indicated that the rock mass was generally poor to extremely poor, and that stoping conditions would be difficult in all of the orebodies for various reasons. A range stope performances were achieved ranging from very good to very poor and in some cases unexpected results were achieved. A comparison is made between what was actually achieved and what was expected since stoping commenced in 2007. Explanations are attempted for differences in stoping performance and, in some cases, unexpected results at the Favona underground mine are attempted.

Nov 25, 2010

By D Xiong, G Xu, L Yao, F Wang, Y Duan

The goal of this project has been to digitise and use drill parameter data from rotary drilling (measurement while drilling; MWD) for a more effective planning of the blasting process in surface mines. A more accurate and reliable digital drilling and automatic hardness identification technology was developed, which includes both a hardware and software system. In the aspect of hardware, we designed a positioning, navigation and hardness perception terminal system which consists of a global positioning system original equipment manufacturer board, programmable logic controller and sensors of measuring major parameters, and a wireless data transmission system which combines digital blasting platform and wireless transmission facilities. In the aspect of software, we developed the navigation software of locating blastholes using LabVIEW and C++, and the blasthole design software using AutoCAD ActiveX (C#) technologies. This new technology is applied at Jiangxi Dexing Copper Mine, and initially realising the digitisation of drilling and hardness identification in blasting zone.CITATION:Duan, Y, Xiong, D, Yao, L, Wang, F and Xu, G, 2015. Advanced technology for setting out of blastholes and measurement while drilling, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 593–598 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By S F. Rogers, K Doumis, J H. Graaf, B J. Barsanti

Advances in technology now allow geotechnical practitioners to better describe the properties and variability of a rock mass through advances in surface and underground mapping, borehole technology and geophysical imaging. Yet the way in which practitioners use this data is not being realised to its full potential and the quality and quantity of data that is collected is often superior to the conventional design approaches that are typically adopted. A discrete fracture network (DFN) approach provides the ideal basis for using this data to generate geologically-realistic rock mass models based on parameters derived from field data, which more effectively capture the variability and rock mass behaviour. However, until recently, the DFN approach has mainly been applied to cave mining and small-scale models associated with synthetic rock mass modelling or groundwater flow modelling for the nuclear waste and oil and gas industries.Ground support design for blocky rock masses in Australia is often dealt with in a rather traditional manner, adopting either an observational empirical approach through rock mass classification systems or conventional wedge stability analysis techniques. Using these methods requires several generalised assumptions about the rock mass fabric and excavation geometry. As such, the support system is often designed for a worst-case scenario based on a predetermined risk tolerance that the mine is willing to accept and a design block size that is generally determined by the proposed excavation dimension.A study by Doumis (2014) used conventional wedge stability analysis and the probabilistic key block analysis software JBlock (Esterhuizen, 1996) to estimate potential block sizes and support requirements. A DFN approach has also been adopted at Callie underground mine using FracMan™ software (Golder Associates, 2014). The methodology of the DFN wedge analysis will be compared with the key block analysis work undertaken by Doumis.CITATION:Graaf, J H, Barsanti, B J, Doumis, K and Rogers, S F, 2014. Towards the implementation of discrete fracture network modelling as a geotechnical design tool – case study of callie underground mine, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 399–408 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By Brumley J

The development of the SECV brown coal open cut at Loy Yang will require depressurisation of aquifers both within and below the coal seam sequence in order to maintain open cut stability. Prediction of future open cut dewatering requirements at Loy Yang Open Cut and evaluation of the regional consequences of dewatering has required development of a detailed hydrogeological model of the Loy Yang area. The complex stratigraphy of the coal seam and aquifer/aquitard sequences at Loy Yang have been analysed and integrated with the hydrogeological concepts developed from regional groundwater studies to formulate a realistic hydrogeological model as a basis for finite-element flow modelling.

Jan 1, 1988

It is difficult to evaluate exploration properties in a manner that is transparent, repeatable and easily re-calculated to cater for different geological interpretations, but the risk-based assessment methodology, the Geological Risk Method, developed and described by Lord et al (2001) attempts to satisfy all these criteria. This paper examines a case study example based on valuations of exploration projects conducted by SRK Consulting using this methodology, and describes some of the advantages and limitations of the method.

Jan 1, 2007

By R E. McIvor, K M. Bartholomew

Classification system efficiency (CSE) is a simple, powerful metric that provides a comprehensive measure of classification system performance. CSE directly quantifies the amount of coarse solids in the mill, and as a result, also directly quantifies the percentage of mill power being used effectively. In this manner, it is an effective, practical grinding energy efficiency metric.Three independent variables drive CSE: circulating load ratio, sharpness of classification, and classifier bypass. Due to practical downstream constrains on per cent solids, improvements realised by increasing circulating load reach diminishing returns as sharpness of classification and bypass deteriorate in the most commonly used classification device, the hydrocyclone. This combination of effects leads to the use of CSE, and its relationship to operational economics, as an objective circuit optimisation criterion.Its simplicity in measurement makes CSE a useful tool for the plant metallurgist, and it is not subject to a great amount of experimental error. CSE provides the plant operator a fast, simple, and effective means to evaluate the performance of the plant classification system. Improvements in CSE relate directly to circuit throughput and energy efficiency. This paper, through description and plant case studies demonstrates the power and utility of this emerging grinding system optimisation metric.CITATION:Bartholomew, K M and McIvor, R E, 2013. Classification system efficiency - a comprehensive closed-circuit grinding optimisation metric, in Proceedings World Gold 2013 , pp 389-394 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By R Fanni, D Reid, M Kulessa

Recent updates to Australian industry guidelines emphasise the importance of the assessment of liquefaction potential of tailings. This includes assessment of the cyclic liquefaction potential, and the post-seismic strength of tailings expected to undergo strength loss from seismic loading. Despite this increase in focus, a relatively small number of Australian tailings appear to have been characterised through cyclic and post-cyclic testing. This paper presents the cyclic characterisation of four Australian tailings, consisting of iron ore, lateritic nickel, vanadium and bauxite residue. Material was obtained either from surficial tube sampling or through remoulding samples in the laboratory from slurries. Testing consisted of monotonic, cyclic and post-cyclic tests for each material. For three of the materials, laboratory-scale shear vane testing was also performed to provide a comparison to post-cyclic strengths from direct simple shear.The results indicated cyclic resistances consistent with the results of other tailings presented in the literature. The lateritic nickel tailings provided the greatest cyclic resistance of the four materials tested, followed by the vanadium tailings. This was somewhat consistent with expectations for material behaviour based on index properties. Post-cyclic strengths were seen to decrease as cyclic strains increased, consistent with typical observations in the literature. Following significant cyclic straining, in some instances the post-cyclic strengths approached those obtained through residual shear vane testing. This provides further insight into the strain-dependent nature of post-cyclic strengths for some materials. The implications of these observations on the post-seismic stability condition are discussed.CITATION:Reid, D, Fanni, R and Kulessa, M, 2015. Cyclic and post-cyclic behaviour of four Australian tailings, in Proceedings Tailings and Mine Waste Management for the 21st Century, pp 207–214 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By H Law, M Muller

Mount Isa Mines (MIM) Copper Concentrator currently utilises Agitair 120 banks for its roughing flotation circuit. Apart from a rotor change, the only other significant work completed to the Agitair banks since their installation and commissioning over 40 years ago has been a like for like refurbishment in 2016. The Agitair banks at the MIM Copper Concentrator currently utilise the Pipsa rotor design which progressively replaced the original Chile X rotor design in the 1980’s and 90’s in the copper concentrator. Since the development of the Pipsa rotors, modern rotors such as the Dorr-Oliver (DO) high shear rotors have been released to the market with proven recovery and concentrate grade improvements over previous rotor designs. This paper aims to detail the installation, testing and comparison of Pipsa versus Dorr-Oliver rotors in two different flotation sections of the MIM Copper Concentrator.CITATION:Muller, M and Law, H, 2018. High shear rotor trials in the Mount Isa Mines Copper Concentrator, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 393–402 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By Nicol SK, Engel MD

Ion flotation involves the adsorption of ionic species, in association with surfactant molecules, at the surface of rising gas bubbles, for the purpose of recovering and concentrating those ions. The objective of this study was to optimise the ion flotation process using a heap-leach liquor, containing gold cyanide, and the surfactant cetyl trimethyl ammonium bromide (CTAB). The aim was to minimise the surfactant reagent dose, maximise the throughput of feed liquor in the process, and satisfy the dual constraints of a high gold recovery and a high volume reduction factor. Development of a first order model of the ion flotation process formed the theoretical basis for the test program procedure and the interpretation of the results. Batch tests were used in order to determine the ultimate recovery curve for the heap leach liquor-CTAB surfactant system. The results indicated that a surfactant dose of about 0.083 g/l would be necessary in order to achieve a satisfactory gold recovery. Continuous tests were then performed on a small-scale pilot plant at the Newcastle Laboratories. The optimum result achieved was a gold recovery of 85 per cent, a volume reduction factor of ten, and a feed throughput of 2.3 m3/m2-h. Recent work also indicates that very much higher volume reductions can be achieved using a larger diameter vessel. The improvement may be a consequence of a reduction in wall effects and hence an improvement in foam drainage.

Jan 1, 1993

By P Ottenio, B CarrT

In the last 40 years, the froth flotation process widely spread in the paper industry becoming the dominant technology for ink removal from recovered paper slurries and cellulose fibres recovery. Most of current models used to describe the flotation deinking process are based on hydrodynamic and statistical theories of ink particles collision/attachment to air bubbles. The complexity of these theoretical models, together with the variability of the recovered papers composition, does not allow to define a set of æeasy to handleÆ equations to be used for modelling industrial flotation cells. This main limiting aspect makes that, in several deinking process modelling tools, basic parameters used to characterise the flotation unit, ie yield, ink removal efficiency, water loss, are constant parameters. Although in some process simulation tools the flotation yield/efficiency is adapted to process control parameters (air ratio, pulp flow, pulp consistency), physicochemical variables (namely the pulp frothing aptitude, the pulp surface tension and the ink adhesion energy to air bubbles) are not taken into account to adjust the flotation yield/efficiency. Data collected during recent laboratory and pilot plant experiments focusing on the role of surface active substances on the flotation efficiency were therefore interpreted and used to identify general trends that could be described with simple semi-empirical models. A set of model equations using surface tension and froth removal height as main variables was then defined in order to describe the behaviour of a pilot flotation cell. Trends obtained during the dynamic simulation of the deinking pilot plant were in good agreement with experimental data obtained under similar experimental conditions, thus indicating that developed equations can forecast with good approximation the behaviour of a flotation deinking unit.

Jan 1, 2005

By R Wei, Y Peng, D Seaman

This study addresses a widespread problem confronting the mining industry: the deleterious effect of clay minerals in flotation. This problem is seemingly exacerbated by the presence of iron contamination from grinding media. The interaction of clay minerals and grinding media in copper and gold flotation was investigated in this study. A low-clay ore and a high-clay ore were obtained from Telfer to represent different contents of clay minerals, while stainless steel and mild steel grinding rods were used to produce different grinding chemistry, in particular, iron contamination. Flotation tests on an unsized and sized basis were conducted to reveal how clay minerals and grinding media affect copper and gold flotation. Iron contamination and the oxidation of copper minerals were quantified by ethylene diamine-tetra acetic acid (EDTA) extraction. It is interesting to find that both clay minerals and iron contamination depressed the flotation primarily in fine particles smaller than 33 ¦m, and clay minerals played a dominant role. Although flotation of coarser particles greater than 33 ¦m was less affected by clay minerals and iron contamination, coarser grinding to increase P80 was not an effective way to improve copper and gold flotation for the high-clay ore. This study suggests that to improve copper and gold flotation from clay ores, clay dispersion in conjunction with the minimisation of iron contamination may be required.CITATION:Wei, R, Peng, Y and Seaman, D, 2013. The effect of grinding media on copper and gold flotation in the presence of clay minerals, in Proceedings World Gold 2013 , pp 283-288 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By MacDonald AJ, Raffield MP

The South Deep massive orebody consists of 20 to 30 in of payable conglomerates ranging in dip from 11¦ to 20¦ and at depths of between 2400 in and 34(10 in. The mine design process selected a mining method with a proven record of application that could be adapted to overcome the inherent difficulties associated with the depth, thickness and structural influences of the South Deep orebody. A modified cut and fill mining method provides a concentrated and highly flexible method of extraction. An integrated destressing cut will enable the modification of the stress environment such that it is suitable for massive mining operations. The choice of backfill type and stoping width in the destressing cut ultimately determines the characteristics of the stress modification and, as such, is critical to the success of the cut and fill operation. This paper discusses the decision process undertaken to determine the optimum backfill type and stoping width combination in terms of, conditions in the destressing cut faces and in the massive mining environment. Numerical modelling has been extensively used to analyse arious scenarios to aid in the decision process.

Jan 1, 1998

By Ham G. I, Just G. D

The model considers a range of design parameters and operating condit- ions and evaluates the significance of these in the ultimate design of a mine. It also considers organizational features associated with the mining method and examines the inter-dependence between operations. An important characteristic of the model is the use of both stochastic and deterministic methods to study the behaviour of the complete mining system. The simulator selects the appropriate unit operation, computes and records its time, performs it and then calculates the production and cost data. Output is in the form of shift, day, week or period repor-ts. These reports will indicate problem areas such as restrictions in the production network for a given set of conditions. The likely effects of alternative means of solving these problems can be evaluated by changing the original input. Such information could be used by the mine management to select an

Jan 1, 1974