Search Documents

By Fukuda M, Kurita K

A mathematical model for estimating the liquid level in the hearth is presented. The analytical result was checked on a cold two-dimensional model and an additional boundary condition for the fundamental equation resulted. The applicability of the resultant equation was investigated on a cold model and a regression equation obtained for the average liquid level for Kashima No. 1 BF. Comparison of calculated and observed results were in fairly good agreement. It is concluded that the liquid level in the commercial furnace can be calculated from the measured values of pressure in the bosh and operating conditions.

Jan 1, 1975

By I Lourel

In evaluating the installation of an in-pit crushing and conveying (IPCC) system for any mine, a number of options are available for each of the dig side, transport and dump side operations. Some of them are moreappropriate than others; given the pit arrangement, the material being handled and the rates at which it needs to be moved. This paper seeks to document the options that might be employed, and to rank them in terms of their applicability at any mine and their practicality overall, with a view to nominating those that would be most suitable for further study.

Jan 1, 2009

By C T. Senra, A Souza

Increasing fuel prices, unavailabilty and high prices of tyres have imposed tremendous challenges for large open pit operations. Carajßs open pit mines, one of the largest iron ore projects in the world, has been particularly affected due to the high amount of giant trucks operating in this site. On the other hand, environmental constraints push the mining industry towards reductions in fossil fuels, noise and waste generation. As a feasible response to these requirements, an alternative mining method for open pit mining, aiming to reduce or even eliminate the need for trucks has been developed, based primarily on coal opencast continuous operations. This innovative approach for open pits involves the replacement of trucks by fully-mobile crushers, bench conveyors and ramp conveyors. Two different applications have been developed for exploiting waste and ore at Carajßs largest pit, named N4E. To make it possible, mine planning paradigms should be replaced leading to new conceptual design of open pits. This paper shows two case studies (waste and ore conceptual design) carried out at Carajßs mines to anticipate and put forward the future of open pit mining, proving that our industry would be greatly affected by this new way of exploitation, reducing thousands of tons of fossil fuels. Productivities can be enhanced and environmental performance greatly improved. In this approach mine automation can be easily implemented reducing operating costs and man's fatigue.

Jan 1, 2009

By M Edgar, G Pattemore, M Auad, K Job, A Job, S Gale

In recent decades, significant advances have improved the modelling techniques for predicting slope failure. Predicting failures is vital in open pit mining due to the significant risk posed to personnel and equipment from unstable pit walls. Failures not only cause harm and damage to people and equipment but also cause delays to production and subsequently increase operational costs. Coupled with improvements in modelling techniques, utilisation of advanced scanning systems, such as high-definition imagery from UAVs has enabled faster and more precise mapping and modelling. However, one key element required for accurate slope stability modelling and monitoring is the ability for mine geotechnical engineers to have an accurate understanding of the mineralogy and moisture content of slopes, in real-time. To address this challenge, research has been undertaken to utilise hyperspectral imaging across a broad spectrum, combined with high-definition imagery, and LiDAR to scan slopes for minerals and moisture content. In addition to accurately mapping mineralogy and moisture, the data must be collected autonomously and remotely to ensure ongoing safety. The results show that there are many direct and indirect benefits from this new technology, including the ability to monitor slopes at a safe distance and in real-time, improved accuracy of modelling, detection of risks, and improving the automation workflow for geotechnical engineers. The paper presents recommendations for the implementation of the technology in open cut mining environments.

Jun 22, 2022

By D Brennan, S Jahanshahi, F Jorgensen

The recycling of metals can be very efficient with careful selection of the material being recycled. The volume and value of recycled ferrous scrap has lead to the development of steel mini-mills which in turn has caused major changes to the steel industry. Although much smaller in volume, the recycling of lead is very significant, with battery recycling accounting for 60 per cent of annual world production. This high recycle rate can be attributed to the relatively uniform feed-stock from lead-acid batteries. The recycling rates of other metals are considerably lower due to longer use and non-uniform product usage that results in less efficient segregation and processing. It is clear that recycling of metals has advantages but its sustainability is uncertain. What are the key benefits of metal recycling? Metal recycling has technical, economic and social impacts. It is relatively easy to assess recycling on a technical basis, but the social impacts are harder to evaluate. This paper examines some of the issues in evaluating the sustainability of metal recycling.

Jan 1, 2002

By E J. Hancock, K H. B Chu

Failures within hard rock underground excavations have historically been defined by a depth of failure, estimated in the field or through individual measurements, with a simplified failure geometry; such as 1/3 span, cubic or paraboloid. This simplified shape, volume and mass of failure is typically used to estimate in situ demand as a simplified discrete point. However, the highly variable failure geometry indicates simplified methods to estimate the mass can be erroneous in comparison to high precision LiDAR scans. Advances in technology have enabled the accurate capture of failure geometry and allow a far more accurate analysis of failures to be completed. This case study investigates a number of real-life failures to accurately define the failure geometry, the distribution of the failure parameters and compares this to traditional methodologies. This paper also outlines a suggested means of standardising failure geometry parameters whilst accounting for their variability.

Nov 29, 2022

By Cox SJD, Kramadibrata S

One of the major causes of accidents and loss of production in underground mines is falls of ground.As mines go deeper, higher stresses are encountered and strain energy stored in the rocks is more likely to be released dynamically. This results in bumping in the rock mass around a stope or development face. Such noises and increasingly difficult ground conditions are obviously a warning of more serious problems ahead. The activity is collectively referred to as rock bursting.In Australia the mining of metalliferous deposits is taking place at increasing depths at Mt Isa, Broken Hill and the Eastern Goldfields and ground control problems with rock bursts has already been experienced at all three sites.

Jan 1, 1990

By P McCarthy

"This paper is based on 30 years of involvement in feasibility studies as a participant, study manager and the leader of a firm that provides study components and overall study management. The following topics are discussed:the purpose of feasibility studiesaligning the goals of the study team with those of the ownerthe difference between optimisation and designhow the types and levels of studies affect the organisation of the studythe relative merits of various management structures and contractual arrangementssetting scopes of work and tendering the work outthe selection of a study manager and the study management teamcommunications within the study team and externallythe project management trianglemanaging scope changes and maintaining flexibility to respond to study findingsprogress paymentsmanaging a study crisisinnovation, risk aversion and bankabilityreporting the resultsthe dangers and benefits of value engineering.CITATION:McCarthy, P, 2016. Making studies work – organisation, communication and management, in Proceedings Project Evaluation 2016, pp 20–30 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 8, 2016

By A B. Richards

A brick veneer house located on a open-pit coal mine lease has been subject to ground vibration levels of up to 222 mm/s, and air vibration levels of up to 145 dBL. The dynamic response of the structure was measured with accelerometers, geophones, and strain gauges as part of a project investigating the response of brick veneer houses to blasting. This paper outlines the project, and provides information on brickwork strength, foundation investigations, and observations on damage due to blasting. Correlations have been made between crack behaviour and factors such as blast vibration levels and rainfall.

Jan 1, 2001

The blasting process involves a complex interaction of a delayed sequence of moving sources of seismic energy which produce nonlinear behaviour near the blast holes. A deterministic description of this nonlinear behaviour represents a formidable problem. The modelling of blast vibrations remote from the blast source may use some of the primary features of the blast design such as charge type, charge weight and initiation sequence. Such modelling of blast vibrations usually assumes linear behaviour remote from the blast holes. Site specific charge weight scaling laws may be used to predict the blast vibration levels with relatively poor accuracy. An important ingredient which is missing from charge weight scaling laws is the seismic source wavelet emanating from each blast hole. The present paper considers some approaches which may be used to determine a suitable source wavelet. The wavelets are suitable for use in the region where linearity may be assumed. In that region, it is possible to model the attenuation and scattering of the seismic wave as it propagates from the blast source to the measurement location.

Jan 1, 1990

By Thirumalai K, Peluso R. G

The United States has more than 45 billion tons of economic coal reserves in seams above 10 feet thick and current underground production from thick seams represent less than three per cent of the total production. A tripling of underground production from thick seams is necessary within the next 10 years to meet U.S. coal production demands. An analysis of underground accident and production data is presented in the paper. A study of accident and injury distribution in different coal seam heights in the eastern and western part of the United States in seams ranging in thicknesses from 5 to 15 feet indicates that the seam thicknesses do not produce adverse impact on underground injury incidence. Accidents associated with roof falls and haulage account for about 70 per cent of underground mining injuries.

Jan 1, 1976

By Brook W. H

The history of the reduction of iron from its ores is lost in antiquity. Archreologists state that man has practised it for over four thousand years. Until comparatively recent times charcoal was the principal reducing agent for making metallic iron from its various oxidised ores. Coke was first used by iron founders in England in 1619, and its use spread gradually throughout the civilised world from then onwards. Indeed, the destruction of forests to obtain the requisite charcoal made the iron founders, both in England and America, extremely unpopular, and this hampered the iron industry to a considerable extent, until coal provided the metallurgist with a new and better fuel--coke which is used by most pyro-metallurgists today. The transition from wood to coal products for iron smelting had a profound effect on the location of iron works. Particularly was this the case in America where, in the infancy of the industry, practically each of the early States had its own iron producers, but as coal and coke replaced charcoal, there came about a concentration of the iron and steel industry around the coking coal deposits, and so today there are huge steel plants clustered around the soft coal basins in Pennsylvania and Illinois.The development of the iron and steel industry in Australia, which is comparatively recent by world standards, has been cradled in the coal basins of New South Wales. The first steel works of any consequence in this country were built near Lithgow, close by the mines which produced the coal for coking.Incidentally, these works were rather unique in that the three essential materials for iron and steel manufacture-ore, coal, and limestone-were found virtually at the works' back door.When, in 1912, the location of the proposed steel works for The Broken Hill Pty. Co. Ltd. for smelting ore from Iron Knob in South Australia was considered, the site ultimately chosen was at Newcastle, almost on top of seams of satisfactory coking coal. One of the major factors which had determined the site of the steel works was the fact that, about 1912, three tons of coal were required to produce one ton of finished steel product, and the relative economics of ore and coal haulage were much in favour of bringing ore to the coal.

Jan 1, 1947

By D Miller, M Dowling, R Domotor

"This paper is focused on blasting activities undertaken as part of the Pacific Highway Upgrade – Tintenbar to Ewingsdale – project (T2E). This is a ‘priority 1’ Pacific Highway road construction project in New South Wales (NSW), to be completed by mid-2015 (weather permitting). T2E will provide approximately 17 km of dual carriageway road starting at the northern end of the Ballina bypass and extending to the Ewingsdale interchange, and will complete the existing dual carriageway road between Ballina and the NSW/Queensland border.Roads and Maritime Services (RMS) (formerly the Roads and Traffic Authority) is delivering the project on behalf of the NSW state and federal governments. In October 2011, RMS awarded a contract to Baulderstone Pty Ltd (now Lend Lease Engineering Pty Ltd – Lend Lease) to design and construct T2E. One of the key elements in this project is the St Helena Tunnel.In order to avoid the steep grades of St Helena Hill, eliminate a well-known accident black spot and maintain the aesthetics of the Byron hinterland escarpment, RMS and Lend Lease prepared designs to construct a 434 m long dual carriageway tunnel, 46 m below the ridge line of St Helena Hill. Lend Lease elected, where geotechnical conditions permitted, to use drill and blast methods to excavate the full tunnel profile, instead of traditional mechanical excavation techniques.Since all blasting locations (both inside and outside the tunnel) were in close proximity to nearby residents, the NSW Department of Planning and Infrastructure imposed strict air blast overpressure (airblast), ground vibration (vibration) limits and limited working hours. Both RMS and Lend Lease recognised that these restrictions meant that nearby residents may be exposed to blasting activities for longer than was necessary. As a result, after close consultation and agreement with the nearby residents, RMS applied successfully to the NSW Department of Planning to increase the airblast and vibration limits, as well as the working hours.Working under these new conditions, Lend Lease employed a range of best practice drill and blast technologies provided by both Orica Australia Pty Ltd and Atlas Copco Mining and Rock Excavation to improve the safety and efficiency of blasting activities and to minimise the potential negative impacts of the blasting works on affected residents. These technologies included: the use of a continuous environmental monitoring system to record the results of the blast events and provide quick and easy reporting to key stakeholders to address RMS specification requirements electronic detonators to enable accurate hole detonation timing for vibration compliance and to give project engineers the flexibility and precision to alter each design to suit the geological profile of each face the use of two software programs and advanced drill rigs to enable the efficient design of blasts, electronic transfer of designs to the drill rigs, as well as in-hole monitoring and recording of drilling performance the use of a specialised bulk emulsion system to deliver fully coupled bulk explosives into face blastholes to maximise fragmentation, and decoupled bulk explosives into perimeter blastholes, to reduce overbreak and deliver a cleaner profile.By taking a progressive approach towards the environmental restrictions and the work hours imposed, as well as utilising best practice blasting techniques, RMS and Lend Lease were able to blast with confidence and achieve their production deadlines and reduce the total cost of the project.Most importantly, RMS and Lend Lease were able to meet their environmental obligations and work constructively with the nearby residents to ensure that the blasting was undertaken as safely and efficiently as possible without delay or negative impact.CITATION:Dowling, M, Domotor, R and Miller, D, 2014. Improving excavation efficiency at the St Helena Tunnel using best practice drill and blast techniques, in Proceedings 15"

Sep 17, 2014

By Merry N, Cocks T

The mineral exploration industry is increasingly aware of the importance of the relationship between mineralogical data and geochemical assay results. However, until recently, the cost and time constraints of most techniques for analysing alteration mineralogy have precluded detailed alteration studies. These impediments have been reduced by the development of the Portable Infrared Mineral Analyser (PIMA), a field portable infrared spectrometer that allows rapid (in field) and cost effective analysis of alteration minerals including subtle variations in mineral crystallinity and Composition.

Jan 1, 1995

SOME 70 miles south-east of the of Auckland lies the town of Waihi-the centre of the Waihi goldfield, at present the mining pride of New Zealand. That the glory of most mining camps is evanescent forms an axiom to which it may be expected Waihi will prove no exception. For the last fifteen years, however, Waihi has been an important gold-silver producer, with an annually increasing output, so that now the area ranks as one of the leading goldfields of the world.

Jan 1, 1911

By D Howe

The Athena gold deposit was discovered in 2007 by Gold Fields Australia Ltd, at the St Ives Gold Mine, 35 km southeast of Kambalda, Western Australia. Gold anomalism was identified in sheared Paringa Basalt as a result of a regional scale aircore drilling program, in association with geophysics. In the 18 months following discovery, the deposit was intensely drilled and by June 2009, it was announced that the Athena deposit contained an ore reserve of 1.7 Mt @ 5.6 g/t for 316 koz. This was followed by a feasibility study, and as a result mine development commenced in November 2009.The Athena mineralisation is hosted in a discrete, north-south striking, steep to moderately dipping shear zone within the southwest dipping Paringa Basalt. Vein intensity has a strong correlation to grade and vein type varies from early thin quartz-albite-sulfide (pyrite and/or pyrrhotite) shear parallel veins to strong brecciation and irregular veining with quartz-albite-actinolite-biotite-pyrrhotite infill. The geology preproduction process developed at the Argo mine was refined and improved following a business improvement project. The aim of the process is to construct detailed geological interpretations prior to development allowing informed mining decisions to be made. The process delivers significant cost savings and revenue enhancements.The development of macroscopic classification scheme was critical to determine ore or waste in the early phases of mining. The Style of Deformation, Alteration and Veining (SAV) Code was the result, and has been enhanced as greater geological knowledge is gained over time.

Aug 22, 2011

By R G. Jeffrey

The Northparkes, Endeavour 26 orebody is a porphyry copperûgold deposit and comprises a moderately to well jointed rock mass characterised by gypsum veining, the intensity of which decreases with depth. The top 480 metres of the orebody is currently being mined by block caving, the undercut dimensions measuring 196 metres in length by 180 metres in width. Continuous caving was never achieved after the completion of the undercut thus cave inducement techniques were sought to maintain caving so as to safely sustain production. The use of hydraulic fracturing as a cave inducement tool was successfully trialled in December 1997 using existing exploration boreholes located midway up the current lift. Subsequent fracturing campaigns have enjoyed various degrees of success and have yielded in excess of seven million tonnes of ore at a significantly lower cost than conventional cave inducement techniques. Monitoring of both the hydraulic fracture system and the rock mass response has provided considerable insight into the geometry, growth and influence of hydraulic fracture networks above the Northparkes block cave, and has initiated additional research into the use of hydraulic fracturing in other mining methods.

Jan 1, 2000

By S Gomez-Hernandez, P D. Munro

Filtered dry stack tailing storage facilities offer many advantages over thickened tailing storage facilities and yet, most of the mining companies still prefer the latter.Some of the advantages of filtered dry stack tailing storage facilities are: increased structural integrity of the tailing storage facility, which is even more critical in areas of high seismicity, close to nearby communities or environmentally sensitive areas; maximised water recovery which is particularly important in arid environments where water is an extremely valuable resource and its supply is regulated; optimised recovery of valuable metals in the process water, avoiding high cyanide concentration going to detoxification (both aspects haven’t been emphasised enough in technical papers on this subject); optimised space to store the tailings in mountainous regions; minimised elevation of embankment height, providing a safe option to store the tailings in places where there is limited area available; simplified license approval to operate where the tailing facility is a big issue; and avoidance of potential problems with nearby communities.Filtered dry stack tailing storage facilities have some disadvantages such as: technology limitations in operations that process high throughputs (eg >50 000 tpd) as they require many filters resulting in high maintenance and operating costs; higher capital cost; low efficiency in the filtration process, particularly in ores with high clay content increasing operating problems and capital cost; the new technology risk with possible debottlenecking issues and a longer time to achieve the design throughput; and the need to treat larger water flow rates when the water balance is negative.This paper analyses: the operating practices of Mexican gold and silver operations using filtered dry stacking storage facilities; implementation issues, advantages and disadvantages; quantifiable reductions in gold and silver losses and actual lower detoxification cost; and current trends to use filtered dry stacking storage facilities in new projects. The data gathered raises questions about (a) the need to collect data on tailings filterability, and; (b) reducing the current high operating cost of tailings filtration.CITATION:Espinosa-Gomez, R, Gomez-Hernandez, S and Munro, P D, 2018. Tailing filtration practices in Mexican gold and silver mines, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 275–282 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

Most types of nuclear power reactors use uranium dioxide fuel. Power reactors using natural uranium dioxide'fuel are of special interest to countries such as Australia that have their own uranium supplies. A wide range of uranium dioxide powders can be fabricated and the ideal one flows readily, presses without the need for binders or lubricants, sinters to the required density and gives low reject rates at all fabrication stages. Sinterable uranium dioxide is usually produced via the ammonium diuranate route. The A.A.E.C. is aiming to demonstrate production of nuclear grade uranium dioxide from Australian concentrates, improving technology where possible. Details are given of the dissolution, solvent extraction, precipitation, filtration, drying, and calcination-reduction steps. Solvent extraction from sulphate media is also under study with a view to developing a process to produce a nuclear grade product at the mine treatment plant site,

Jan 1, 1969

By J P. Burr

The Waterview Connection will complete a strategic Auckland motorway route linking the south, west and north. The project will include 2.1 km of ‘undrained’ driven tunnels, 500 m of drained cut-and-cover tunnel and tunnel portals.The project is aligned beneath a stream valley of Oakley Creek, which is incised through alluvium and in places overlain by landfill, between Mt Albert volcano and a ridge formed in alternating sandstones and siltstones. The resulting topography, geology and hydrogeology of the tunnel alignment are complex.The Assessment of Effects required estimation of the likely settlements resulting from the tunnel construction and assessment of their effects on the buildings, services and other features. A conservative approach was taken when estimating settlements in order to provide an upper bound estimate of the consequent effects. There are three sources of these settlements: mechanical settlement from the tunnel excavation, mechanical settlement from the displacement of retaining walls and consolidation settlement from the groundwater drawdowns during construction and, in some cases, in the long-term.The settlements from these sources were calculated independently and then combined to identify the most critical effects. These combined settlements were used to assess the potential damage to the buildings, services and other features above and around the tunnels. The combined settlement results generally followed the anticipated trough shape centred on the underlying tunnel but with some noticeable effects relating to the underlying geology and hydrogeology.The effects on buildings were typically assessed as negligible with some areas of very slight to moderate damage predicted. Effects on services are anticipated to be minor but some large and older pipes will require specific monitoring during construction. A monitoring programme is proposed to allow the actual settlement and effects to be compared to those estimated with appropriate responses should those effects significantly differ.This paper describes the methods used to calculate and combine the settlements and assess their effects.

Mar 8, 2011