Search Documents

Common brattice cloths in use in Australian coal mines are compared by permeability measurements. The respective advantages of twill weave and tarpauling* weave cloths are listed, and the improvements to be obtained in the ventilation of a mine by using tarpauling cloths instead of the commonly used twill cloths are stressed. Plastic cloths are widely used overseas and are briefly discussed.INTRODUCTIONThe onset of extensive full-scale mechanization in Australian coal mines during the past few years has increased attention given to the ventilation of working places. Many inadequacies of the present system have been brought to light and not the least of these is connected with the use of brattice cloth, both in directing the flow of air around the face and in acting as a temporary sealing mechanism. A well-constructed line of brattice will only provide fair ventilation for a distance of 100 ft. Beyond this point the volume or air reaching the face falls off rapidly.Some of the shortcomings associated' with the use of brattice cloths are:1. Hurried installation, necessitated by a rapid advance, often results in poor workmanship with, consequently, an excessively high leakage rate.2. High places caused by falls of roof are difficult and time-consuming to seal.3. Curtains, in lines of brattice crossing transport routes, are difficult to maintain.4. Lines of brattice interfere with rock-dusting and clean-up of fine coal.5. Repair and maintenance of brattice consumes much...

Jan 1, 1959

"Quang Ninh province is located in the north east of Vietnam and the coal mining in the province generates two thirds of the province’s GDP. The coal is extracted from both open pit and underground mines for the country’s complete coal export and by a share of more than 90% for domestic coal usage. Overburden generated through open pit mines is piled up nearby in the form of large waste rock dumps. The side-hill fill dumping near open pit mines is the source of environmental degradation in the region. Among the current problems at solid waste rock dump sites are dust emissions during and after dumping as well as Acid Rock Drainage (ARD). One of the major existing problems at waste rock dumps is dump stability (comprising erosion, sliding and subsidence issues). The RAME R&D project (Research Association Mining and Environment in Vietnam) is - among other activities - actively involved in the research for stabilisation and rehabilitation of mine waste rock dumps in Vietnam in the form of several sub-projects. The Institute of Mining Engineering I of RWTH Aachen University is leading the sub-project of mine waste dump stabilisation in co-operation with Chair of Geotechnical Engineering and Brenk Systemplanung GmbH. Mine waste dumping in the form of layers as an alternative to the side-hill fill dumping is expected to bring up environmental and economical benefits by minimising the problems of dump sites with the contribution to a sustainable development. Reduction of the post construction settlements, long term stable dump profile with minimum erosion, improvement of material parameters for geotechnical slope stability through compaction from hauling trucks as well as economical evaluation of new dumping concepts are the areas of the current research. The project has been financed by German Federal Ministry for Research and Education (BMBF). The ultimate aim of the sub-project is the compilation of the project results in the form of a "Best Practice Guide" and software based "Decision Support System" for planning and management of solid mine waste dumps."

Jan 1, 2011

By J. R. Thoenen

[Before 1914 Germany held virtual monopoly on the world supply of potash for fertilizer purposes. During the world War, potash shipments to the United States ceased, and recourse was had to domestic supplies. High war-time prices stimulated interest n various sources, and domestic production increased rapidly. At the close of the war, resumption of shipments from Germany and other sources reduced prices to below pre-war levels, and, as a result, most of the domestic producers ceased operational.]

Jan 1, 1941

By L. Su, S. Liu, K. Jiang, K. Xie

The reduction of iron dissolution and acid consumption is fairly important in the extraction of Ni and Co from laterite ores from both economic and efficiency perspectives. BGRIMM conducted detailed research to investigate the behavior of iron in a nickel laterite leaching process. The mineralogy of Ni and Co was studied. In limonite ore about 76% of nickel is present in goethite while in saprolite ore 79% of nickel is associated with magnesium and silicon minerals. Test work revealed that limonite can be decomposed completely with enough acid concentration during atmospheric leaching. More than 98% of Ni and Co were leached into solution while 85% of the iron was also dissolved with 130-140 g/L iron in solution. Iron precipitates as hematite in the temperature range 250-270?C without neutralization reagents. That’s why limonite is treated by high pressure acid leaching (HPAL) technology to achieve nickel extraction and iron precipitation in the same autoclave. BGRIMM’s test results indicated that the remaining acid in atmospheric leaching solution and acid released by iron precipitation at a lower temperature was enough to leach saprolite efficiently. The so-called inverse leaching technology leaches limonite at atmospheric condition and the leaching slurry combined with saprolite is pumped into an autoclave to leach saprolite at 150-170?C. In the autoclave iron precipitates as hematite without acid consumption. Total nickel and cobalt extractions in the test program were more than 90% with iron content in solution below 8 g/L. In this inverse process iron dissolves in the atmospheric leaching stage and precipitates as hematite in the low temperature leaching stage. Compared with HPAL the leaching temperature is reduced to 150-170 ºC from 250-270 ºC. Compared to atmospheric tank leaching acid consumption is reduced from 850-950 kg/t ore (atmospheric) to 550-650 kg/t ore (inverse).

Jan 1, 2016

By James V. Errico

On October 1, 1993 the regulations for assessing and cleaning up contaminated soil and groundwater in the Commonwealth of Massachusetts were revised. These new regulations, known as the Massachusetts Contingency Plan (MCP) 310 CMR 40.0000, were developed to keep routine releases out of the regulatory system and rely on private parties to handle most releases without Department of Environmental Protection (DEP) oversight. An integral part of the new MCP is the Licensed Site Professional (LSP). An LSP is required to handle activities and render opinions once a site enters the MCP. These regulations must be adhered to where ever a release has occurred, including construction sites. A brief overview of the new MCP is given below; see attached MCP Flowchart for graphical summary. Entering the MCP Process A release of oil or hazardous material (OHM) to the soil or groundwater above applicable reportable quantities (RQ's) or reportable concentrations (RC's) will require notification to the DEP and compliance with applicable provisions of the MCP. RQ's and RC's are listed in the MCP (310 CMR 40.1600) for most compounds that are typically encountered. For each compound there are two RC's for soil (S-1 and S-2) and two for groundwater (GW-1 and GW-2). The S-1 and GW-1 RC's apply to sites that are environmentally more sensitive, as a result they are lower than the S-2 and GW-2 RC's.

Jan 1, 1994

By Z. Xiao, A. R. Laplante

"The recovery of gold by gravity from grinding circuits differs from virtually all other gravity recovery approaches in that stage (or unit) recoveries are low, typically 1 to 5%, but overall recoveries are generally in the 25 to 60% range, because individual gold particles are presented many times to the primary recovery unit. Full-scale recovery is difficult to predict from benchscale tests. Further, maximizing metallurgical recovery is generally not the primary objective, because of the more efficient downstream recovery circuit (flotation or cyanidation). In this paper, a new concept, the gravity recovery effort, is presented to assist in the design and optimization of gold gravity circuits. It is defined as the product of the circulating load treated by the primary gravity unit, the recovery of this unit, and the gold room recovery. Predicted gold recovery is linked to the recovery effort, the size distribution of gravity recoverable gold (GRG), the dimensionless retention time in the mill and the partition curve of GRG. A case study of economic optimization of the gravity recovery effort is presented. INTRODUCTIONPredicting gold gravity recovery from grinding circuits has always been a hit-and-miss exercise. The problem can be traced to the highly variable gravity recoverable gold (GRG) content of ores, high GRG circulating load, fraction of the circulating load treated, and performance of primary gravity recovery and gold room. Typical values, highs and lows are shown in Table 1."

Jan 1, 2001

By Tumilty JA, Schmidt CG

Sulphide ion is a powerful poison in gold cyanidation, however, the detrimental effect is less severe in plant practice. This is thought to be due to the presence of depassivating elements in the ore, mainly lead. Trace amounts of lead can counteract the poisonous effect of considerable amounts of sulphide. The reaction is instantaneous and is likely to be a direct involvement in the electrochemical surface reaction. Lead addition cannot be regarded as an all-round cure when experiencing poor leach efficiencies. A possible beneficial effect depends on the mineralogy of the ore and has to be determined individually for every material.

Jan 1, 1989

By D. F. Scott

Seismic tomography, as used in mining, is based on the principle that highly stressed rock will demonstrate relatively higher P-wave velocities than rock under less stress. A decrease or increase in stress over time can be verified by comparing successive tomograms. Personnel at the Spokane Research Center have been investigating the use of seismic tomography to identify stress in remnant ore pillars in deep (greater than 1220 m) underground mines. In this process, three-dimensional seismic surveys are conducted in a pillar between mine levels. A sledgehammer is used to generate P-waves, which are recorded by geophones connected to a stacking signal seismograph capable of collecting and storing the P-wave data. Travel times are input into a spreadsheet, and apparent velocities are then generated and merged into imaging software. Mine workings are superimposed over apparent P-wave velocity contours to generate a final tomographic image. Results of a seismic tomographic survey at the Sunshine Mine, Kellogg, ID, indicate that low- velocity areas (low stress) are associated with mine workings and high-velocity areas (higher stress) are associated with areas where no mining has taken place. A high stress gradient was identified in an area where ground failed. From this tomographic survey, as well as four earlier surveys at other deep underground mines, a method was developed to identify relative stress in remnant ore pillars. This information is useful in making decisions about miner safety when mining such ore pillars.

Jan 1, 1996

By J. J. Brummer

The possibility of diamonds occurring in Canada was first raised by W. H. Hobbs in 1899, who concluded: "that the apex of the fan of diamond distribution probably lies somewhere in the strip of the territory bordering James Bay on the east." This was based on the occurrence of diamonds in surficial sediments at various locations south of the Great Lakes. There are two recorded discoveries of drift diamonds in Ontario: (a) the Peterborough Diamond, 33 carats in size, poorly documented and found sometime before 1920;and (b) the Jarvi Diamond, 0.255 carat, found during 1971 in Sheraton Township near Timmins . Both discoveries were in surficial sediments and their source(s) have not been located. During 1960, Selco Exploration Company Ltd. started a heavy-mineral sample program of river gravels in the James Bay Lowlands of Ontario. This was continued by Canadian Rock Company Ltd. (1962-1963) and the Ontario Division of Mines (1973). The surveys discovered the presence of kimberlite minerals in gravel samples from streams draining the Moose River Basin. A total of 53 pyrope grains, four magnesian ilmenites and one grain of chrome diopside were identified from 32 sample locations. A study of the distribution of these minerals suggested the kimberlite source rocks to be located along the north margin or within the Kapuskasing gravity "high" in the area immediately south of James Bay. The Jarvi Diamond, found on an esker east of Timmins, could well have originated from this area. During 1965, an esker was sampled by the Geological Survey of Canada, and the results attracted attention to the area south of Lake Abitibi. At 9 out of 34 sites sampled along the Munro esker, Lee recorded the presence of pyrope garnets and very minor chrome diopside.

Jan 1, 1978

This paper reports on recent field observations on the performance of support systems under different corrosion environments in Canadian underground mines. Phenomenological data are used to gain a better understanding of the main causes of corrosion in underground metal mines. Preliminary field data collected from five metal mines have been complemented by atmospheric and water sample analysis as well as fractography and metallographic studies. This has identified dominant factors that control the corrosion of support systems. The data are analysed in order to develop a support strategy for mines operating in corrosion environments.

Jan 1, 2008

IN this paper it is proposed to present certain features of operating practice at the Port Pirie works of The Broken Hill Associated Smelters Proprietary Limited, in the smelting in a blast furnace of lead ores carrying a high concentration of zinc.The subject matter selected for presentation is:(i) The effect of zinc on lead blast-furnace operations, together with an outline of the methods adopted in actual practice in dealing with the zinc problem.(2) Development of the height of tuyere above the bottom of the jacket, and the extension of the tapping interval and the combined effect of both factors upon the lead content of blast furnace slag.It will later be seen that one phase of the investigation carried out in connection with the effect of zinc on blast-furnace operations was largely responsible for the decision to increase to a marked degree the height of the tuyere above the bottom of the jacket.Due to this interdependence, it has been considered advisable to deal with the two features above mentioned.The high concentration of zinc in the lead-bearing materials smelted at Port Pirie has brought with it those troubles which are associated with zinc in the smelting operation.In the early stages of the history of The Broken Hill Associated Smelters Pty. Ltd. the trend towards increasing cost for labour, fuel, and stores, etc., rendered it necessary to increase the lead content of the charge, and reduce to a minimum the quantity of barren flux used.

Jan 1, 1931

By J. M. Dean, R. L. Grayson, R. C. Althouse, M. J. Klishis, G. L. Winn

Using powerful database management software, nested-field analysis and microanalysis of narratives have been made of West Virginia accident data, resulting in a new approach for targeting and prioritizing safety interventions by county, mine size, specific mine, job title, type injury, etc. and combinations of these parameters. The analyses have been useful in focusing training and discussion sessions on specific work problems, trends, conditions, and situations for targeted groups of miners. Application of the technique will be presented in this paper, along with comparisons of various mine performance measures.

Feb 24, 1997

Models are used in engineering to reproduce reality as faithfully as possible so that the expected response of a system for given actions or inputs can be determined. In the field of rock engineering, both empirically based and numerical models are widely used to determine the likely response of the rock surrounding excavations. Many of the empirical models are developed from statistical analysis of case histories or from direct observation; however, empirical models are limited because they should be used only within the range of conditions of the observational database. Synergy exists between empirical and numerical models, because empirical models can be used to calibrate and validate numerical models. The empirical approach can benefit from the capability of numerical models to investigate specific mechanisms, which would not be possible using observations alone. Two cases are presented in which the synergy between empirical and numerical models is demonstrated. The first case examines the analysis of discontinuity effects on the strength of slender pillars in limestone mines, and the second case evaluates the effects of stress orientation on coal mine entry stability. It is concluded that numerical model calibration and verification comprises an important first stage in the successful application of models in rock engineering design. Application of numerical models allows mechanisms and interactions of various parameters to be analysed, greatly improving the understanding of the system. The improved understanding can be used to extend the application of empirical design methods, resulting in improved safety and efficiency of rock engineering designs.

Jan 1, 2014

By Joram M. Amir

Even when they are cased! [ ] In bored piles, as well as in drilled shafts, and in caissons too, defects will occur! [ ]

Jan 1, 2001

By A. Uiga

The U.S. Bureau of Mines funded a project which addressed objectives concerning irrigation of native plants and inoculation of native plants with vesicular-arbuscular mycorrhizal (VAM) fungi. The specific irrigation objectives were 1) to demonstrate the performance capabilities of solid-set irrigation for reclaimed mineland conditions, and 2) to demonstrate and evaluate three irrigation concepts under two separate water supply conditions. The VAM inoculations were to assess irrigation benefits in establishing VAM relationships for transplanted native species. Following the seasonal demonstration (May to September 1983) at 3 separate mine sites, conclusions were made that apply to the 6 state Western mining industry. The demonstration sites were located in Montana, Wyoming, and New Mexico. Positive conclusions were reached for 1) the use of soil moisture sampling with or without irrigation, and 2) the selection of solid-set sprinklers as the irrigation method. The conclusions about the irrigation concepts and strategy were mixed, due to the short-term (1 season) nature of the project. No conclusions could be reached for the VAM inoculations because the study time was too short.

Jan 1, 1984

Updraft sintering of lead concentrates was introduced at Port Pirie in 1955 and since that time a considerable amount of investigational work has been carried out in the laboratory and on the plant with the objective of improving both the understanding of the process and its practical application.From this work it is now possible to predict trends in design and operation, which should result in capital savings and increased efficiency of future updraught plants.INTRODUCTIONOver the last 70 years a remarkable advance has been made in the method of preparing lead concentrates for smelting in the Port Pide blast furnaces of The Broken Hill Associated Smelters Pty. Ltd. (RH.A.S.). Beginning in 1889 with heap roasting, the process progressed to Ropp roasters and Huntington-Heberlein pots in various combinations, then to multiple small Dwight Lloyd (D.L.) downdraught machines. In 1940 two large 10 ft by 50 ft D.L. downdraught machines were installed, and finally in 1955 updraught sintering was ,introduced with the installation of the present 10 ft by 99 ft sinter machine.At the time this last machine was built it was the first unit of its type and thus, of necessity, an experimental machine. During the eight years it has been operating a considerable amount of investigational work on sintering has been carried out both on the plant and in the laboratory.It is now felt that sufficient information is on hand to predict at least tentatively, some of the future developments in lead sintering, whereby both the quality of the sinter and the rate of production may be improved. This will result in a considerable reduction in smelting costs.

Jan 1, 1964

By Amy McBrayer, Andrea Brickey

Area mining is a surface mining method that allows for efficient mining and contemporaneous reclamation of tabular or bedded deposits, e.g., coal. Mine planning methods for area mines differ from those of open pit metal mines. Area mines in the Powder River Basin (PRB) use various processes for mine planning at both the strategic and tactical stages. With the ever changing commodity markets, it is becoming increasingly important for mine operators to be able to react quickly to the changing business environment. Tools that allow for the development and rapid comparison of production schedule scenarios are key to ensuring agile mine operations. A survey of mine engineers responsible for mine design and production scheduling at coal operations provides clarity on the current mine design and production scheduling processes in the PRB, as well as a discussion on potential solutions to upcoming challenges. In this article, we describe various mine planning processes used by the coal producers in the Powder River Basin. The survey identifies a clear gap in the ability to create comprehensive schedules associated with limited tools and lack of engineering labor needed to frequently conduct the mine design and scheduling process.

Jul 8, 2023

By Walter I. Paniagua

A housing complex of 76 buildings is being constructed in the city of Morelia, in western central Mexico; the buildings are 5 levels high, with a shallow concrete slab foundation. Soil conditions include a soft clay stratum, with up to 8 m depth, in a highly seismic area. Pile foundations and micro-piles were considered, but discarded due to economic factors. The alternative of soil improvement with rigid inclusions was used. An FEM (Finite Element Method) analysis was conducted to determine the diameter, spacing, length and arrangement of the inclusions. Construction was implemented with traditional methods: soil boring, and mortar tremied with pipe and the aid of a sock to contain the material (no steel reinforcement was used). So far, 46 buildings have been built, and level measurements for 18 buildings have been recorded since 2006, with resulting good behavior in both total and differential settlements.

Jan 1, 2008

By Seffen Leppla, Rolf Katzenbach, Matthias Seip

"Abstract The economic and safe design of deep foundation systems in difficult soil conditions is based on a reduction of construction material used, construction time spent, energy consumed and a high-level modelling of the soil-structure-interaction. The special foundation system Combined Pile- Raft Foundation (CPRF), in-situ load tests on the construction site and a sufficient soil investigation allow cost optimised constructions. In any case at challenging projects the observational method has to be applied for verification and quality control of the design. Regarding the 4-Eye-Principle as basis of the quality control management an independent peer review of the planning, design and construction phases is the guarantee for safety, serviceability and optimisation of all projects. Main execution standards for the construction of deep foundations based on the Eurocode 7 are summarised and discussed. The paper presents the basics of the safe and qualified design and construction of foundation systems including quality assurance. The application in engineering practice is shown on achallenging project of high-rise buildings with difficult boundary conditions.IntroductionThe construction of deep foundation elements in inner cities are special challenges due to the limited space for the construction works and the effects on existing buildings (Figure 1).An economic and safe design of deep foundation systems in difficult soil conditions is based on the following main aspects:•,qualified experts for planning, design and construction•,interaction between architects, structural engineers and geotechnical engineers•,adequate soil investigation•,design of deep foundation systems using the Finite-Element-Method (FEM) in combination with•,enhanced in-situ load tests for calibrating the soil parameters used in the numerical simulations•,quality assurance by an independent peer review process (4-eye-principle) combined with theobservational method if necessary"

Jan 1, 2014

By E. C. Perkins

As part of a program for developing methods of using domestic titanium deposits, the Bureau of Mines investigated methods for chlorinating titanium slags prepared from titaniferous minerals by electrosmelting. Titaniferous slags were made from ilmenites in the following deposits: Valley County, Idaho; Trail Ridge, Fla.; Aiken, S. C.; and Maclntyre, N. Y.; titaniferous magnetite from Iron Mountain, Wyo., were also evaluated. The tests were made in two chlorinators, a 4-inch and a 36-inch unit. Preliminary testing was done in a 40-millimeter bench-type unit. Chlorine gas was contacted with a loose mixture of titaniferous slag and carbon at a high temperature to form titanium tetrachloride. The moving-bed system used in this work involved a downward movement of feed countercurrent to the chlorine flow, and residues continuously removed from the bottom of the reactor. The performance characteristics of these slags depended on their composition, which varied widely according to the geographic source of the ore. The results showed that all but two of the slags could be chlorinated as effectively as rutile, converting 70 to 80 percent of the titanium to the tetra-, chloride. The two slags that proved difficult were made from New York ilmenite and Wyoming titaniferous magnetite. These slags contained enough magnesium to cause clinkering, which necessitated that the bed be prematurely withdrawn before more than 70 percent of it could react. The iron content of the slags did not interfere with operating the chlorinators. The data from the 4-inch and the 36-inch units were in agreement on the relative amenability of the slags to chlorination.

Jan 1, 1962