Search Documents

By Ian Vaz, Takefumi Takuma

"The New Orleans area has been repeatedly flooded by major storms and hurricanes since its French colonial era. After severe flooding in May 1995, the U.S. Congress authorized a massive flood protection project called the Southeast Louisiana Urban Flood Control Program (SELA) in 1996 to improve interior drainage in Orleans, Jefferson, and St. Tammany parishes. However, the project was not fully funded before the landing of Hurricane Katrina in 2005 and Hurricane Rita, which breached many of the area’s levees and flooded 80 percent of the city. Finally, the project was fully funded in 2008 and has been worked on towards its 2017 completion. Another large project simultaneously worked on in the area is the Hurricane and Storm Damage Risk Reduction System (HSDRRS). This system was designed for a 100-year level of flood risk reduction. One particular project within the HSDRRS rendered successful due to an unconventional method of pile driving that was utilized to install sheet piles to reinforce an existing concrete I-wall. This paper will discuss how and why this non-vibratory method of sheet pile installation allowed the project to be successfully completed ahead of schedule.INTRODUCTIONSteel sheet piles were utilized on many of the SELA and HSDRRS projects for permanent cutoff walls under concrete I-walls or T-walls or for temporary earth retaining walls of drainage structures. Although the SELA Project was established in 1996 after severe flooding the year before, hardly any work was done on it until the two catastrophic storms Hurricanes known as Katrina and Rita triggered its revival. These two hurricanes also triggered the HSDRRS soon after the storms’ devastation. The SELA project authorized to improve interior drainage systems while the HSDRRS project was authorized to raise or restore levees and floodwalls mainly along Lake Pontchartrain, the Mississippi River, and Lake Borgne in addition to other areas. Figure 1 shows the SELA Projects that have been completed, are still under construction, or approved for construction. The projects fully highlighted in yellow within the map specified the press-in piling method. These improvements included drainage systems, pump stations, surge walls, and outfall canals as enhanced protection for future storms similar to Hurricane Katrina that caused so much damage by inundating the New Orleans area in August and September 2005 respectively (Facts and Figures, 2012). The completion of these projects were the responsibility of the U.S. Army Corps of Engineers, New Orleans District.Due to the fact that many of the projects were in densely populated areas, the Army Corps of Engineers specified a non-impact, non-vibratory press-in piling method for driving and extracting sheet piles for many of the projects to mitigate noise and vibration impacts. The soft soil conditions in the New Orleans area was also a contributing factor in the Army Corps of Engineers’ decision to specify this piling method due to the risk of settlement for existing historical as well as modern structures. In addition, there were other projects that elected to use the press-in method without any contractual requirements. One of these projects was the Inner Harbor Navigational Canal Reach II Emergency Interim Repair which was part of the HSDRRS project that has been under construction since its authorization in 2005 (Facts and Figures, 2012)."

Jan 1, 2017

Jan 1, 1993

By S. Maurhofer

The Uetliberg Tunnel in Switzerland is the longest tunnel in Zurich?s new Western Bypass Expressway, connecting the Birmensdorf bypass in the west with the existing Zurich-Chur national motorway in the east. Thus the tunnel links the Zurich-West motorway interchange with the Zurich-South interchange (shown in Figure 1). The Uetliberg Tunnel project comprises two parallel tubes, each about 4.4 km long. The two tunnel tubes are connected every 300 m by a transverse walkway and every 900 m by a transverse roadway (Figure 2). The SOS niches are spaced 150 m apart. Portal stations with machinery rooms are located at the west and east portals. The tunnel falls with a gradient of 1.6% from the west portal at Wannenboden to the east portal at Gänziloo. The Project costs are about CHF 1.12 billion. The carcass construction started in March 2001. The Opening of the Uetliberg Tunnel is planed in spring 2009.

By A. C. Fieldner

"INTRODUCTION In a previous report3 prepared for the American Gas Association, the influence of washing coal on coke properties and on gas and by-product yields was discussed on the basis of answers to questionnaires sent to coke-oven superintendents and a review of the literature on the subject. This review indicated that the elimination of free impurities by cleaning coal improved coke quality by (a) reducing ash and sulphur, (b) decreasing clinker trouble in burning the coke, (c) diminishing cross fractures in the coke, resulting in greater resistance to breakage on handling, and less small coke and breeze, and (d) greater uniformity in chemical composition and physical properties of coke. Washing also reduced the sulphur in coke and gas and increased the yield of gas and by-products per ton of dry coal charged.This paper is supplementary to the previous report and presents some experimental data obtained with Pittsburgh bed coal from Pennsylvania and Mary Lee bed coal from Alabama.ACKNOWLEDGMENTSGrateful acknowledgment is made to F. J. Pfluke, of the Rochester Gas and Electric Cc., of Rochester, N. Y., for the plant test data on screened lump and washed coal; and to Ray W. Arms, Manager of the Coal Cleaning Department, of Roberts & Schaefer Co., of Chicago, for the data on effect of air cleaning."

May 1, 1931

By David J. White

The decreasing availability of land in urban areas, and the increasing demand for urban development is leading to the construction of taller and heavier buildings at increasingly marginal sites. Such structures usually require founding at depth and modern construction methods are making the economics of piled foundations ever more attractive (Salgado, 1995). However, the urban environment is not suited to pile driving. Conventional dynamic installation techniques (i.e. drop hammer or vibro-piling) induce vibrations and settlement in a zone close to the pile, and cause noise and dust pollution. Damage to existing structures resulting from pile driving vibrations is not uncommon (Tomlinson, 1986).

Jan 1, 2000

By Thomas J. Weaver

Piles extending through soft soil near the ground surface will have a relatively low lateral stiffness. As a result, lateral serviceability limits may control the number of piles required for foundation support. Improving near surface soil properties may significantly increase lateral pile stiffness and thus reduce the number of piles required for the foundation. A series of analyses have been performed to assess the depth and lateral extent of soil improvement required to significantly increase lateral foundation stiffness. Analyses consisted of Winkler type beam on a spring foundation and three-dimensional, linear elastic finite element analyses. Results from the analyses show that lateral pile foundation stiffness can be doubled when soil properties are improved to a depth and lateral extent of 5 pile diameters. In order to achieve this increase in foundation stiffness, the modified/improved soil modulus of elasticity needed to be approximately 5 times greater than adjacent unimproved soil. This magnitude of soil improvement over such a limited lateral extent suggests that limited soil improvement can result in more economical foundation designs at soft soil sites.

Jan 1, 2006

By J. D. Nye, I. A. Farr, W. J. D. Stone

"A unique deposit of barite exists near Brookfield, Nova Scotia. The crystals are extremely fine and the whole deposit virtually free of heavy metals. The deposit size was not large enough for conventional uses, such as the production of barium carbonate and drilling mud. In an effort to obtain maximum utilization, a program was begun to determine if U.S.P.-grade pharmaceutical barium sulphate for X-ray diagnosis could be produced. Early work was sufficiently encouraging to institute a development program under the federal Program for Advancement of Industrial Technology. This has been very successfully completed. Canadian and U.S. process patents have been issued, clinical trials have been successful, a production plant has been designed and the plant’s production sold. The processing plant will include magnetic separation for the removal of iron minerals, fine grinding by paddle milling to minus one micron and acid leaching. The process is unique in that at no time is the barium taken into solution.Information is given on the deposit, process, markets, use, plant capital and operating costs, and projected profits. The initial production plant will have an annual capacity of 2,000 tons per year of end product. Capital cost is $850,000 and annual turnover more than $1.5 million. As this capacity only represents approximately 15% of the North American market, rapid plant expansion is foreseen."

Jan 1, 1980

By Constance Holmes

President Lien presented Mrs. Holmes with the first of speaker appreciation gifts presented by his firm Amax Coal West, Inc. These were books by Rand-McNally entitled The Executive Golfer Guide. Following the coffee break, Clark Moseley presented the first annual Institute Safety Achievement Awards for the safest mines in the eight member state region. The awards were based on: 1. Total man-hours 2. Total number of lost time accidents 3. Incidence rate 4. Number of S&S violations 5. Description of safety program 6. Safety awards received 7. Health and safety training efforts 8. Safety Policies 9. Does the operation take employee suggestions and implement them? 10. Letter(s) of commendation from agencies individuals The awards were judged by the senior/graduate level class of Mine Safety & Health at the Colorado School of Mines under the supervision of professor Edward Hollop. The two handsome traveling trophies were awarded to and accepted by: Surface: Big Sky Mine. Colstrip, Montana Gordon Brannon, Manager of Safety Underground: Skyline Mine, Scofield, Utah Dave Hales. Safety Supervisor and Doug Johnson, General Production [ ]

Jan 1, 1998

By Robert Hopler

This article, advocating having employees whose specific job would be to fire blasts in underground coal mines in llinois, was written 5 years prior to the establishment of the U.S. Bureau of Mines, and 2 1/2 years before the worst month in U.S. coal mining history, when 692 miners were killed in three separate explosions in December 1907. Obviously something had to be done to improve safety in the use of explosives, and having dedicated shotfirers was a good first step.

Jan 1, 2006

By J. Kuijpers

Failure and fracturing are often regarded as synonymous. While this is obviously true in an environment dominated by tensile stresses, it is still not clear how failure and macro fracturing are related in a compressive stress environment. Excavations at great depths are typically subjected to compressive stresses only. The fracturing observed around such excavations is therefore commonly assumed to be induced by such compressive stresses. The physics of such a phenomenon have unfortunately never been explained properly, so that the formation of these so-called extension fractures still remains a mystery. As the presence of fractures is an important factor affecting the stability of underground excavations, it is of practical relevance to understand their formation. In this paper, a possible explanation is proposed. It is argued that fracturing in a compressive stress environment is a secondary effect. Primary failure, in the form of micro fracturing and associated damage is assumed to precede the major fracture processes. The fractures are thus generated in response to material failure and may not directly be the cause of failure. The implications for material response and behaviour are discussed. Keywords: micro fracturing, macro fracturing, extension fractures, failure, compressive stresses, damage, excavations.

Jan 1, 2000

By A. Krause

Shovel-truck systems for loading and hauling material in open pit mines are now routinely analysed using simulation models or off-the-shelf simulation software packages, which can be very expensive for once-off or occasional use. The simulation models invariably produce different estimations of fleet sizes due to their differing estimations of cycle time. No single model or package can accurately estimate the required fleet size because the fleet operating parameters are characteristically random and dynamic. In order to improve confidence in sizing the fleet for a mining project, at least two estimation models should be used. This paper demonstrates that the Machine Repair Model can be modified and used as a model for estimating truck fleet size in an open pit shovel-truck system. The modified Machine Repair Model is first applied to a virtual open pit mine case study. The results compare favourably to output from other estimation models using the same input parameters for the virtual mine. The modified Machine Repair Model is further applied to an existing open pit coal operation, the Kwagga Section of Optimum Colliery as a case study. Again the results confirm those obtained from the virtual mine case study. It is concluded that the Machine Repair Model can be an affordable model compared to off-the-shelf generic software because it is easily modelled in Microsoft Excel, a software platform that most mines already use. This paper reports part of the work of a MSc research study submitted to the University of Witwatersrand, Johannesburg, South Africa. Keywords: simulation, bunching, probability distributions, cycle time, queuing, matching, shovel-truck, OEM.

Jan 1, 2007

By K. Hoover, G. Labarre, S. Rantanen

"As part of the Namew Lake project a mill was constructed to treat 1900 tpd of ore grading approximately 0.90% CU and 2.45% Ni to produce copper and nickel concentrates.Nickel occurs mainly as pentlandite and violarite while copper occurs as chalcopyrite. Two main ore types are present1 lower grade disseminated sulphides in a talcose ultramafic gangue and a higher grade solid sulfide with a granitic breccia matrix.Primary crushed ore from underground is treated on surface in a conventional closed circuit crushing plant using 2-stage cone crushing. Crushed ore is conveyed to storage and then fed at a controlled rate to a grinding circuit employing a rod and ball mill with hydrocyclone classification. Rougher flotation separates and cleans nickel and copper sulfides from waste materials followed by a high lime separation circuit to separate the minerals into final concentrates. Dewatering is achieved through use of high capacity thickeners and pressure filters prior to delivery to a loadout area. The crushing and milling control is highly automated.Plant design was based on metallurgical samples obtained from drill cores. After the first year of operations, plant results compared favourably with design projections.INTRODUCTIONThe Namew Lake Project is a joint venture partnership between Outokumpu Mines Ltd. (Canada) and Hudson Bay Mining and Smelting Company Ltd. (60%). The project included construction of a mine and milling complex to treat approximately 500,000 tonnes per year of copper-nickel ore grading o.91% and 2.44% Ni. Known reserves are estimated at 2. 65 million tonnes. The deposit is located approximately 65 km south of Flin Flon (120 km by road) and about 5 km east of the Manitoba-Saskatchewan border. The decision to construct a concentrating facility was made June 15, 1987 and construction started a week later. The facility, designed for 1900 tonne per day throughput, was ready for commissioning in September 1988. Outokumpu Engineering of Finland was chosen to prepare metallurgical flowsheets, select and develop plant layouts, and provide construction management. Kilborn (Toronto) contributed detailed engineering for civil, structural, mechanical and electrical components and outokumpu Equipment of Canada, the design, the supply, and commissioning of the instrumentation package. Hudson Bay undertook the initial metallurgical test work and preliminary design work."

Jan 1, 1990

By Gerrit V. R. Goodman

In This Chapter [Design and operation of machine-mounted scrubbers Dust control with scrubbers and blowing ventilation Dust control with scrubbers and exhaust ventilation Dust control with exhaust ventilation and no scrubber Dust control methods common to all continuous miner sections Dust control for roof bolters] This chapter explains how to control dust at continuous miner sections in coal mines where the main dust sources are continuous miners and roof bolters. In relation to dust, there are three categories of continuous miner faces depending on the type of ventilation and whether or not a machine-mounted dust scrubber is used. These are— 1. Mining machines with dust scrubbers used with blowing face ventilation 2. Mining machines with dust scrubbers used with exhaust face ventilation 3. Mining machines without scrubbers used with exhaust face ventilation The approach to dust control is somewhat different in all three of these. However, there are many dust control features (such as the need to provide adequate airflow) common to all continuous miner sections. For workers at roof bolter faces, there are two dust sources: 1. Dust from the continuous miner when it is upwind. 2. A malfunctioning dust collector on the bolter, which allows dust to escape DESIGN AND OPERATION OF MACHINE-MOUNTED SCRUBBERS [Almost all new continuous miners are equipped with scrubbers. When the dust is excessive, it is possible that the scrubber needs some maintenance.]

Jan 6, 2003

By Oliver Bowles

This paper is the third of a series of reports on asbestos prepared by the Bureau of Mines. The reports already issued contain general information, including descriptions of deposits throughout the world.3/ The present paper deals chiefly with milling and marketing. Many grades of asbestos are marketed, and an important phase of milling is the grading of fiber; these subjects therefore are related so intimately that contiguity in their treatment is fully justified. Although the Bureau of Mines is interested primarily in the mining and preparation of raw materials, the fabrication of asbestos products has attained such importance in the United States that brief reference to processes of manufacture is included. CLASSIFICATION OF FIBER Canadian asbestos fibers are divided into three main groups - crudes, mill fibers, and shorts. The term "crude" is applied to fiber of spinning grade measuring three eighths inch or longer, that is. hand-cobbed and not passed through a mill. Mill fibers are obtained by crushing and beating the fiber-bearing" rock, until the, asbestos is freed and, then removing the fiber from the rock by screening or air separation. Shorts are the lowest grades of mill products.

Jan 1, 1935

By T. P. Williams, M. B. Rydzewski, B. Corner

Konkola Copper Mines (KCM) plc is an integrated copper producer operating on the Copperbelt in Zambia. KCM has numerous mining operations located in the towns of Chililabombwe (Konkola Mine), Chingola (Nchanga Open Pit and Underground operations), Lusaka (Nampundwe Mine), with a smelter located in Kitwe (Nkana Smelter) and an SX-EW plant in Chingola (Nchanga Tailings Leach Plant). [ ]

Jan 1, 2005

The AusIMM/AMIC code for reporting Reserves seeks to improve the calibre of professional reporting on this subject. But have they gone far enough? Should the code appreciate that the degree of reliability of estimates required will vary with the type of mining planned? How does one "confirm continuity" as required by the code? The aim of optimum development drilling is to achieve appropriate ore zone definition for acceptable estimates of reserves and their economic extraction. Can this procedure be in conflict with the code? How does it affect finance decisions?

Jan 1, 1989

By R. B. Toombs

In describing the Canadian mineral industry in a world setting, this paper examines the industry from four points of view. First, mineral industry growth is related to trends in economic activity thereby providing a measure of the industry's importance in the Canadian economy. To give perspective to the Canadian scene, reference is made to economic trends in several of the world's leading mineral producing and mineral consuming countries. The Canadian mineral industry is next examined in terms of its major developments of the past 20 years and the resultant size, structure, and production diversity of 1964. The position of the Canadian mineral industry in the world industry is then analyzed by tracing changes in mineral supply and demand patterns. Growth of the Canadian industry depends greatly on expansion of export markets because three fifths of the value of production is accounted for by exports. Finally, attention is directed to the outlook for the Canadian mineral industry. Problems facing the industry are surveyed, and an appraisal is made of economic policies that have encouraged industry growth. A forecast of mineral production value in 1970 is included.

Jan 1, 1964

By Antonio Karzulovic, Ricardo Sepulveda, Manuel Schellman

Mantoverde Division of Empresa Minera Mantos Blancos S.A., Anglo American Chile, developed an open pit mine to exploit copper oxide ore. Mantoverde mine is located in the Province of Chañaral, Northern Chile, about 1,020 Km far from Santiago. Currently, the East wall of the mine is reaching the condition of final pit. To evaluate the possibility of a pit optimization on this wall a geotechnical study was performed, including slope stability analyses by limit equilibrium and numerical methods. As a result of this geotechnical evaluation, it was decided to allow a probability of failure of 12% for instabilities affecting up to 600,000 tonnes, and use steeper slopes on the East Wall of the mine. This paper describes this geotechnical evaluation and how the results of the stability analyses were used to define a flexible slope design, which allows modification if the observed slope behaviour deviated from the expected one.

Jan 1, 2006

By X. S. Tan

This paper deals with the analysis of stress condition on the interface between two types of floor rock materials when the vertical stress is larger, or when the horizontal stress is larger in a rectangular opening. It indicates that the floor Failure and the failure stress of floor rocks are closely related. It also demonstrates that a larger horizontal stress is one of the most important factors in increasing the potential for floor rock failure and floor heave.

Jan 1, 1990

By Gray Mullins

This paper presents experimental results from a study to assess the interface bond between a cast-in-place concrete seal slab and prestressed concrete piles in cofferdams. Three different seal slab placement conditions - fresh water, salt water and bentonite slurry - were evaluated and the results compared against controls where no fluid had to be displaced by the concrete. Normal pile surfaces were investigated. Additionally, the situation of ?soil caked? piles was also investigated. Both model and full-scale tests were conducted. In the model tests, twenty eight 15 cm square prestressed sections were used with the embedment depth varied between d-2d, where d is the width of the pile. In the full-scale tests, 16 specimens were tested. The prestressed piles were 36 cm square with the embedment varied between 0.5d-2d. Four of the sixteen piles were cast with embedded gages located at the top, middle and bottom of the interface region. The results showed that loads were transferred to the piles over an effective area, not the entire embedded depth. Significant bond stresses developed even for the worst placement condition. Recommendations are made for revising current values in specifications.

Jan 1, 2013