Search Documents

By Donald Koch

The project investigated regional impacts of mining on the ground water system of the Powder River Basin by: 1) establishment of a regional ground water monitoring network, and 2)development of , set of digital computer models to simulate ground water flow and quality, ground water contributions to surface water flow and quality (i.e., baseflow), and watershed run-off and recharge. Over 100 wells were monitored for physical and chemical parameters. Data were used as input to the model; and for the development of a comprehensive data base. The basin was modeled on a regional and subregional scale using a finite -difference model employing an alternating difference technique. Two water-shed models were evaluated for their ability to provide runoff and recharge inputs to the basic ground water model. Application of the regional and subregional models using conservative mining scenarios showed that drawdowns may extend west from the mines as far as ten miles but that impacts would be insignificant on a regional scale. The watershed model could be effectively applied to small watersheds only.

Jan 1, 1982

By W. G. Freeman

It is unlikely, as In the past, improvement in truck efficiency and capacity can fully offset the effects of inflation, fuel costs/shortages and ever increasing haul distances. There-fore, investigations of haulage systems less sensitive to these problems are warranted. Thus, this U.S.B.M. contract research study on alternative continuous haulage systems was prepared. This study identifies the physical, economic and technological parameters in the application of continuous haulage systems with special attention to under pit slope conveyors and skip hoisting systems. The evaluation data was gathered from extensive literature searches. European/North American mine visits, and industry comments. The study concludes that continuous underground haulage is a viable method within the proper geometric configuration.

Jan 1, 1978

By Thomas F. Connors

The end of an era is here. The pony-express era of industrial relations in the coal industry is ending. Those professionals who know it must end to insure the industry's future are happy, relieved, but somewhat saddened. They are sad because it did have its elements of suspense, thrills, frustrations, and at times, plain fun. The days of the Company town are ended; the wildcats are declining; violence (while a big part of today's industrial relations) is beginning-to decline. The spirit of sound industrial relations is beginning to take hold. This has to happen for the industry to compete in today's economy and it is causing major changes for those who have grown accustomed to the pony-express type industrial relations.

Jan 1, 1981

By Jae R. Lee

Keywords: Self-propagating high temperature synthesis, AlN, Powder synthesis The particle size and shape effects of starting raw powders on the synthesis of aluminum nitride by self-propagating high temperature technique under high nitrogen pressure were investigated with various AlN diluents and Al reactants. It was found that the structure of beds of the starting raw particles largely affected the pore channels for nitrogen gas infiltration as well as the passages for combustion propagation before and during the reaction, resulting in the morphology and purity changes of the synthesized products. The AlN product of purity over 98% with about 30 microns was obtained.

Jan 1, 2005

By E. I. Gedgagov, A. V. Tarasov, V. M. Paretsky, A. D. Besser

"Hydrometallurgical technology and equipment have been developed in the Gintsvetmet Institute (Moscow, Russia) for processing of rhenium-containing alloys waste to produce commercial- grade metal products with recovery of all valuable components. The technology is based on waste treatment with hydrofluoric acid with subsequent decomposition with nitric acid at pH = 1 to 1.5 to ensure maximum degree of rhenium conversion to the liquid phase of pulp. Some experimental lots of ammonium rhenate and ammonium molybdate were produced at a pilot plant. The following main techno-economic performance values have been achieved when processing grinding residues (balance-based tests were conducted with a lot of SP-2 alloy waste) to produce ammonium rhenate of high purity, as well as tantalum-niobium, nickel-cobalt and tungsten-molybdenum concentrates: rhenium recovery of 92.3% into a commercial product from grinding waste; production cost of 170-210 US Dollars per 1 kg of rhenium in commercial-grade ammonium perrhenate taking into account its recovery; tantalum and niobium recovery of 75- 77% into bulk concentrate; nickel and cobalt recovery of 88-89% into a mixed concentrate; tungsten and molybdenum recovery of 88% to 91% into concentrate. Introduction During the recent years the use of rhenium has been increasing at a fast pace worldwide [1]. The growing prices for this refractory metal are an essential factor encouraging collection and processing of rhenium-containing wastes. Double-component waste, such as molybdenum- rhenium or tungsten-rhenium alloys can be readily decomposed and the process of rhenium recovery does not cause, therefore, any difficulties. The main separation of metals takes place at the stage of waste digestion with acid, because molybdenum and especially tungsten remain in precipitate in the form of hydrated oxides and rhenium reports in the liquid phase, from which it can be easily extracted by solid ion-exchange or solvent extraction techniques. However, most of rhenium is contained in super-alloy waste [2]. Such waste has different contents of valuable components, such as tantalum, niobium, molybdenum, tungsten, cobalt, nickel, chromium and other metals. The basis of all such super-alloy waste is nickel. Refractory metals in the super- alloy composition are in the form of metallized target-oriented eutectics, and due to this reason hydrometallurgical decomposition of such alloys is a difficult technological task."

Jan 1, 2008

By Shawn Orser, Jennifer Waddell, Mike Sierakowski, Tom Barrett

Production evaluations were conducted at Daisy Gold Mine (Glamis Gold, formerly Rayrock), between August, 1997 and August, 1998 to quantify the effect of 3M fluorochemical surfactants (fluorosurfactants) on extraction kinetics and gold recovery in gold heap leach mining operations. Ore was treated at a level of 7-10 grams surfactant per ton of ore using 3M Pluorad TM Leach Mining Additive PC-GOLD. Kinetics and gold recovery were determined by solution assay for each of the tests. Both tests indicated improved kinetics, and data from Test 2 was used for determination of a quantitative increase in gold recovery resulting from PC-GOLD addition. A discussion of test results including methods used to determine gold recovery is provided.

Jan 1, 2000

By Richard C. Moore

The U.S. Bureau of Mines contracted a study to review the air and water monitoring requirements of five Federal environmental acts (the Federal Water Pollution Control Act, the Safe Drinking Water Act, the Clean Air Act, the Surface Mining Control and Reclamation Act, and the Resource Conservation and Recovery Act) and to compile information on the currently available monitoring instruments. A literature review of the acts and their associated regulations was conducted to determine applicability to the mining industry as well as any air and water monitoring requirements. In addition, an industry search and literature review was performed to assess the instrumentation available to comply with the monitoring regulations. Based on this research, the instruments are classified by general applicability to air, surface water, or ground water monitoring, then catalogued by monitoring parameters. A discussion is provided on recommended and innovative monitoring techniques.

Jan 1, 1981

By A. Philipp, A. S. Middleton, G. A. Harron, A. B. Durham

"Basal till sampling techniques were used to search for gold mineralization in the Timmins, Ontario area. During 1978 and 1979, approximately 90 overburden sampling drill holes were completed in Murphy and Hoyle Townships to test specific geophysically defined target areas. A conventional tricone dual tube drill system, and a unique retractable tricone/rock coring system were used to various advantages.First pass till sampling at 800 to 1200 ft intervals perpendicular to ice transport direction yielded anomalous gold values in till and carbonatized quartz pyrite-rich bedrock chips, and lateritic soil. Subsequent induced polarization-resistivity surveys defined the areal extent of a pyritic carbonate alteration zone. A second pass till sampling/limited rock coring program evaluated the gold mineralization potential of the alteration zone. Diamond drilling has substantiated the till and bedrock gold anomalies. Further evaluation of this mineralization is currently in progress. IntroductionThis paper describes an integrated geochemical/geophysical gold mineralization discovery case history in Hoyle Township. This discovery is on a property jointly owned (I983) by Canamax Resources Inc. and Du Pont of Canada Exploration Limited. Exploration of the property began in 1978 by Rosario Resources Canada Ltd. and in 1979 a joint venture agreement was signed with Du Pont of Canada Exploration Limited. Rosario Resources Canada Ltd. was taken over by Amax Minerals Exploration in 1981, which became Canamax Resources Inc. in 1982.The work described in this paper deals with a gold mineralization discovery located three-quarters of a mile northwest of the gold deposit currently being readied for underground exploration and development. Further drilling is required to investigate the economic potential of the gold mineralization herein described."

Jan 1, 1987

By R. W. Lawrence

"In the past year, BioteQ Environmental Technologies Inc. have initiated design and construction of new plants to add to an existing list of plants that utilize the BioSulphide® and ChemSulphide™ process technologies for metal recovery and water treatment. In these plants, low cost biogenic sulfide or, in some cases, chemical sulfide reagent is used to selectively remove metals from contaminated water. The process produces high grade, marketable, metal sulfide products even from low grade feed solutions. The revenues generated from the sale of products can allow for water treatment at a profit in some cases, offset treatment costs in others, and generally reduce sludge disposal and management costs. The effluents produced from the process can meet stringent environmental standards. Current plants in operation and under construction range in sulphide demand from 50 kg/day to 3.7 tonnes/day, with the feasibility of larger plants with sulfide demands ranging from 6 to 43 tonnes/day under review.Biogenic sulfide reagent can also be considered for other applications in hydrometallurgy and mineral processing. Uses under consideration by a number of mining companies include: (1) replacement of sodium hydrosulphide in the SART process for cyanide regeneration and copper recovery in the processing of gold-copper ores, and (2) replacement of sodium hydrosulphide for use in the separation of copper and molybdenum in flotation. Biogenic sulphide, produced on demand at site, offers significant cost savings and provides the additional benefit of improved safety due to the elimination of the transportation, handling and storage required for chemical sulphide reagents.This paper reviews the applications of the BioSulphide® and ChemSulphide™ technologies for water treatment and metal recovery, and introduces projects where biogenic sulfide can be applied in hydrometallurgy and mineral processing."

Jan 1, 2007

By Louis J. Sousa

This Bureau of Mines report examines aggregate trends in foreign direct investment in the U.S. mining and mineral processing industries between 1977 and 1984, and provides an analysis of foreign investment in several major mineral commodity industries. In 1984, 11.1 pct of total employment in the U.S. minerals industry was at firms that were U.S. affiliates of foreign firms. In 1985, the proportion of U.S. capacity held by foreign investors in nine major mineral commodity industries was as follows: steel, 5 pct; silver, 16 pct; lead, 18 pct; aluminum, 25 pct; zinc, 26 pct ; copper, 30 pet; cement, 32: pct; gold, 44 pct; and ferroalloys, 56 pct. Almost 90 pct of the total foreign investment in the U.S. minerals industry was accounted for by eight countries-Canada, the United Kingdom, France, Federal Republic of Germany, Switzerland, Japan, Australia, and the Republic of South Africa. The most fundamental reason behind the growth in foreign investment in the U.S. minerals industry has been that an increasing proportion of U.S. mineral firms and assets have been for safe, while foreign mineral companies have been the ones most willing and able to purchase these firms and/or their assets. mile the growth in foreign ownership in the minerals industry has not been without controversy, it has helped save jobs, reduce the minerals trade deficit, and- from the national defense perspective-maintain the Nation's overall mineral and metal self-sufficiency at reasonably high levels. In the absence of domestic buyers, foreign investors have helped to maintain a viable domestic minerals industry.

Jan 1, 1987

By W. D. Monaghan

Flame cutting and welding is one of the major causes of fires and explosions in underground U.S. coal mines. On May 20, 2006, a flame cutting operation at the Darby Mine No. 1 led to an explosion that resulted in five fatalities. On January 22, 2003, another explosion caused by flame cutting at the McElroy Mine resulted in three fatalities and three serious injuries. On June 22, 1999, a flame cutting and welding operation at the Loveridge Mine caused a fire that resulted in sealing of the mine for an extended period. Finally, on March 19, 1992, an explosion at the Blacksville No. 1 Mine that was caused by welding resulted in four fatalities. The National Institute for Occupational Safety and Health (NIOSH) conducted a study on fires and explosions in underground U.S. coal mines that were caused by flame cutting and welding operations to determine the root causes of these types of fires and explosions. The methodology included interviewing mining personnel who perform flame cutting or welding operations in underground U.S. coal mines and visiting mines to observe these operations, and MSHA reports of investigations and accidents statistics were analyzed. The results were used to identify and compare differences between flame cutting and welding practices and techniques in small and large mines, Eastern and Western mines, low seam and high seam mines, room and pillar and longwall mines, and between experienced miners and new miners. As a result of this study, best practices and interventions were developed to reduce the number of fires and explosions caused by flame cutting and welding. This paper provides a summary of this work. Disclaimer: The finding and conclusion in this report are those of the authors and do not necessarily represent the views of the National Institute for Occupation Safety and Health.

Jan 1, 2009

By R. G. Burn

"A brief outline will be given of the concept of risk and its implications with regard to investment in exploration. The relationship between risk and decisions under uncertainty will be examined as a prelude to identifying those factors which contribute to exploration risks:consideration of the effects of corporate objectives (e.g. survival, expansion, diversification) on exploration strategy and ultimately on success or failure, exploration and mining as an investment (the relationship between risk and reward) and the desired return on investment; exploration odds, funding levels, staying power, financial exposure and the concept of gambler's ruin;origins of uncertainty in exploration decision-making-man-made risks and natural hazards; the nature of introduced constraints at each exploration decision stage and their effect on the rate of success;improving the chances of success and the invest reduction of risk through sound exploration strategy, effective project generation and efficient target detection capabilities."

Jan 1, 1984

By Alla D. Mah

The need for more and better basic thermodynamic data for the oxides of many of the rare metals is evident to anyone who attempts thermodynamic calculations involving these substances. In continuation of a Bureau of Mines program to meet this need, this paper reports new experimental values of the heats of formation at 298.15° K. of the hexagonal crystalline variety of germanium dioxide and germanium dioxide glass. The values were obtained by means of combustion calorimetry and sodium hydroxide-solution calorimetry. The calorimetric results also made possible the derivation of values for the heat and entropy of fusion of hexagonal germanium dioxide at its melting point. The newly measured data were combined with previously known entropy and high-temperature heat content values to obtain heats and free energies of formation of germanium dioxide (in the hexagonal crystalline, glassy, and liquid states) over the temperature range from 298.15° to 2,000° K.

Jan 1, 1962

By Braam Blom

PK2 Ventilation shaft is part of Paardekraal No 2 twin shaft system that is being developed to replace depleting Merensky reef production at Paardekraal shaft complex. The sinking team at this shaft faced considerable challenge of improving the total sinking cycle in order to be able to deliver the fully equipped shaft on time and on schedule. The cladding support cycle was identified as the tedious and time consuming activity in the overall shaft sinking operation. Reduction in the time required for handling and setting up the support installation equipment, and the time required for subsequent installation of the necessary support has a direct impact on the overall cycle time, and consequently the overall productivity and efficiency of the sinking operation. This reduction in support cycle was achieved by making use of machine carousel. The objective of this paper is to describe the support methodology that was used during the ventilation shaft sinking and the use of the machine carousel to reduce the cladding support cycle. The machine carousel replaces the traditional use of machine kibble in conventional vertical shaft sinking and has been designed specifically for installation of sidewall support at the shaft bottom during the sinking process.

Jan 1, 2009

By Dave Bulled

"This paper describes the design of a molybdenite flotation circuit using FLEET technology applied to kinetics data produced from laboratory flotation testing and distributed across the blocks of a mine plan using a geostatistical approach. The geostatistics assigned the statistical error that arises from having a limited amount of sample testing data to the kinetics estimates of each block of ore in the mine plan. The final design then included a quantification of risk based on the accuracy of the block flotation kinetics and model fitting. The design made reference to the extensive technical reports describing earlier metallurgical test work including some pilot plant work over thirty years ago.The testing involved conducting MinnovEX Flotation Tests (MFT) to determine the rougher flotation kinetics at the specified reagent conditions and rougher-cleaner tests to determine the change in kinetics resulting from regrind. These flotation kinetics were used within FLEET simulations to create a full-scale flowsheet and plant design including recommended equipment sizes and the forecast of operating results. Measurement of detailed flotation kinetics for a wide range of samples allowed the effect of size of grind and efficiency of classification (i.e. width of size distribution) to be predicted for the whole ore body.INTRODUCTIONAdanac Moly Corp. proposed to develop a 20,000 ton per day mill to produce high quality molybdenite concentrate from its Ruby Creek resource in north-western British Columbia. It is a relatively clean low grade porphyry-monzonite occurrence containing minimal quantities of other sulphides such as chalcopyrite, pyrite, sphalerite and galena. Molybdenite occurs mainly as coarse flakes with lesser amounts of finer sized values. An optimum plant design was required to can achieve the predicted operating results, at a known level of risk, while treating the variability inherent in the ore body."

Jan 1, 2007

By William C. Cooley

SUMMARY A review is presented of the state of development of high pressure water jet equipment and of large impact hammers for rock tunneling. Information from the U.S.S.R. is based on published literature and three personal visits. Applicable papers which were presented at the International Symposium on Jet Cutting Technology in Coventry, England in April 1972 are reviewed. Data are presented on continuous jet systems, pulsed water cannons, and hydraulic-powered impact hammers with respect to the specific energy of rock breakage and potential application in tunneling machines. INTRODUCTION It has been estimated that the cost of underground excavation during the period 1970-1979 in 15 countries of the Organization for Economic Cooperation and Development will be over $54 billion, an increase of 104% over the period 1960-1969. It is expected that 55% of the tunneling construction will occur in hard rock (Ref. 1). Present tunneling machines are generally limited to soft and medium-hard rock. When used in hard rock, the cost of replacing mechanical cutter bits is high. Therefore there is a need for improved rock fracture methods which can be applied economically in tunneling machines for hard rock. Water jets and mechanical hammers are two

Jan 1, 1997

A composite iron ore-reductant pellet is a mixture of fine iron ore and fines of coal/char/coke, bonded at essentially room temperature with sufficient green strength for subsequent handling. In ironmaking, these pellets offer the advantage of fast reduction, utilisation of fines, non-coking coal and coke breeze. The composite pellet-based alternative ironmaking processes constitute a promising route for ironmaking in future. The present paper is a brief review of kinetics and mechanism of reduction of iron oxides into iron and other associated reactions, when these pellets are heated to high temperature. It would draw significantly from investigations conducted by the author and his co-workers.

Jan 1, 1999

By Norman O. Lotter

Drill core is preferred as the sample material for metallurgical and mineralogical characterisation and flowsheeting of an orebody. The question arises as to how to do this at the economic optimum, since geologists have several other strategic uses for their drill core. The limiting factors are the cost of extra drilling for the metallurgical testwork and the need to preserve the drill core record. In this study, the representative sampling of drill core at an economic optimum for metallurgical testing is addressed. This phase of the drill core work is preceded by earlier drill core characterisation - for which other appropriate sampling protocols are used - that has provisionally categorised the orebody into geometallurgical units. In stratified sampling of drill core, use is made of a version of the stratified approach to compound distributions proposed by Cochran in 1946. Use is made of Gy’s 50-piece minimum sample mass model to estimate minimum requisite sample mass. In the case where sampling and testwork are required on a Lifeof- Mine blend of a given ore deposit, whereby defined ore types or geometallurgical units are present, the sample mass requirement is significantly reduced by working from drill-core at the geometallurgical unit level. A case study using Raglan drill core is discussed. Using nickel as an indicator paymetal, and sampling at a fundamental variance level of 8%, the minimum sample masses for disseminated sulphides, net-textured sulphides, and massive sulphides are 3.80, 7.37 and 4.39 kg respectively. When the same drill-core is sampled as a Life-of-Mine mixture without knowledge of the geometallurgical units, the minimum sample mass increases to 84.28 kg. It is thus possible to assemble a representative Life-of-Mine sample of drill-core more economically, at the same time validating its representativity. Equivalent calculations for copper, platinum and palladium are discussed, with outcomes consistent with this finding. When all four paymetals are considered, one selects the largest minimum mass out of all four cases. This results in minimum sample masses of 11.67, 74.90 and 175.16 kg for disseminated sulphides, net-textured sulphides and massive sulphides respectively. The simulated Life-of- Mine blend would require a minimum sample mass of 377.33 kg to cover all four paymetals.

Jan 1, 2010

By K. G. Wheeland, J. E. Dutrizac, M. Wasserlauf, A. A. Condy

Numerous processes for the treatment of thiosalts in base metal milling effluents have been examined in the past decade. Flowsheets for thirteen processes are outlined, and cost estimates are presented for a base case of a 720 mi/h effluent flow containing 1400 mg/L thiosalts. The processes are ranked on the basis of Numerous processes for the treatment of thiosalts in base metal milling effluents have been examined in the past decade. Flowsheets for thirteen processes are outlined, and cost estimates are presented for a base case of a 720 mi/h effluent flow containing 1400 mg/L thiosalts. The processes are ranked on the basis of

Jan 1, 1988

By John Russell

"The South American mining community leads the world in recognition and adoption of the latest grinding mill relining technologies. Clearly this region has recognised the benefits of improved relining performance.Six of the seven RUSSELL TWIN 8 Mill Relining Systems, ordered to date, are either operating or being manufactured for South American mine sites.This paradigm shift, towards very short relining times, aims at displacing mill relining activities from the critical path of concentrator maintenance shutdown schedules.The first uses of the RUSSELL TWIN 8 Mill Relining System have seen some of the highest SAG mill new liner placement rates ever observed by RME, as would be expected with two, independent Machines working simultaneously in the one mill.The liner-replacement-rate, averaged over the whole reline, is good (27% improvement over single Machine System in the same mill) but short of full potential. This modest result can be attributed to reline crews unfamiliarity with RUSSELL TWIN 8 System operation.This paper compares a sample of conventional (single machine) RME Mill Relining System performance data with one ‘double head’ mill liner handler by others. Early performance of Escondida’s new RUSSELL TWIN 8 System performance is then compared with recent single Machine data from Escondida, immediately prior to RUSSELL TWIN 8 commissioning. RME and Escondida look to constantly improving RUSSELL TWIN 8 System performance as full operational familiarity is achieved.Also, the preparation of this paper revealed a need to develop a global industry standard for mill relining data collection. A web based platform, to develop and then distribute standardised data collection templates, is discussed in Annexure 1."

Jan 1, 2010