Search Documents

Experimental investigations were made into the decoppering of lead, tin, and bismuth using a technique which approximates on the small scale to industrial practice.Decoppering lead with sulphur alone in the absence of tin and silver did not proceed to low copper values. With a minimum of 0·02 per cent Ag or 0·10 per cent Sn, lead was decoppered to less than 0·01 per cent Cuby stirring with 0·2 per cent S over 10 min. Decoppering of tin or bismuth proceeded rapidly to very low levels in the absence of any "catalytic" impurities, at any rate in excess of those concentrations normally encountered in commercially pure tin or bismuth.

Jan 1, 1971

By Goldney L. H

The authors review the literature and discuss the application of methods to the design of thickeners for ilocculated metallurgical pulps. The use and evaluation of flocculents is described. Experimental data show that design based upon laboratory settlingdata is acceptable. The economic aspect of design is also discussed.INTRODUCTIONFor many years there has been little change in the methods for the design of thickener installations. While modifications have been made in the method of applying the data all methods have been based on the observee settling rate of the solids. The development of a theoretical approach based on physical data would involve so many variables which affect the settling rate that the more practical approach of direct observation seems unlikely to be replaced as the basis of design.The advent of synthetic fiocculents has introduced a modification in operation which affects design and should be considered. The authors review the subject and attempt to bring it up to date with present day procedure. Until recently the original work of Coe and Clevenger (1916) remained the basis of thickener design. They described their observation of the different zones encountered in settling, namely clarification, feed, transition, and compression or thickening- zones. The solids pass through the transition zone in settling from feed density to some higher density where settling ceases and ·some compression or compaction effect controls. the density obtained. The point at which the settling zone ceases to exist is known as the critical point.

Jan 1, 1959

By M. J. McLeod, S. Watters, G. G. Lutes, S. Castonguay

"Gold-bearing mineralization at Anomaly A occurs in polydeformed Ordovician turbidites of the Kendall Mountain Formation of the St. Croix belt in southwestern New Brunswick, and is hosted by WSWtrending, shallow-dipping, brittle-ductile high-strain zones associated with the latest stage of the second of four regional deformation events. Gold-bearing syn-deformational stockwork, massive, and multiply brecciated quartz-sulfide veined zones form irregular pods and sheets up to several meters thick, which contain arsenopyrite, pyrrhotite, pyrite, stibnite, and a variety of rare minerals that are gold-bearing. Mineralized zones are enveloped by locally auriferous, weakly to intensely altered wall rock. Vein paragenesis includes: (1) early (pre- to syn-D2) quartz-chlorite veins that are largely the product of migration of quartz by pressure solution; (2) crosscutting, multiphase, vuggy quartz-sulfide veins that contain most of the gold and are interpreted to be structurally controlled; (3) late, crosscutting, nondeformed, non-gold-bearing veins containing laumontite, chlorite, muscovite, quartz, fluorite, and base metal sulfides. Carbonate-poor alteration associated with zones of gold mineralization is lithology-specific, and appears to reflect overprinting of multiple events. Major elements removed during alteration include Si, Na, Mn, and Mg. The minor and trace elements removed include Co, Li, Sc, and possibly Sr, Ni, and Zn. Minor and trace elements added include Au, Ag, As, Sb, S, and possibly F, Cu, Pb, and Zr. On the basis of proximity, time constraints, and a similar ore mineral assemblage, gold mineralization at Anomaly A is interpreted to be a distal equivalent of the intrusion-related gold mineralization at the nearby Clarence Stream Main zone deposit. La minéralisation aurifère de l’Anomalie A se trouve dans des turbidites Ordoviciennes polydéformées de la Formation de Kendall Mountain, dans la ceinture de Ste-Croix du sud-ouest du Nouveau Brunswick, où elle est contenue dans des zones de déformation fragile-ductile à faible pendage de direction OSO associées au dernier stade du second de quatre épisodes de déformation régionale. Les zones aurifères syn-déformationelles se présentent en forme massive, de stockwork, ou de veines de quartz-sulfure bréchifiées à répétition formant des lentilles irrégulières et des couches de plusieurs mètres d’épaisseur contenant de l’arsénopyrite, de la pyrrhotite, de la pyrite, de la stibine, ainsi que divers minéraux aurifères rares. Les zones minéralisées sont entourées d’une enveloppe de roches faiblement à intensément altérées, localement aurifères. La paragénèse des veines comprend : (1) des veines précoces de quartz-chlorite (pré- à syn-D2) qui sont principalement le produit de la migration du quartz par solution-pression; (2) des veines polyphasées de quartz drusique et de sulfures contenant la plus grande partie de l’or, celles-ci sont considérées comme étant sujettes à un contrôle structural; (3) des veines tardives stériles, sécantes et non déformées contenant de la laumontite, de la chlorite, de la muscovite, du quartz, de la fluorite et des sulfures de métaux usuels. Les zones de minéralisation aurifère sont associées à une faible altération en carbonate contrôlée par la lithologie et semble résulter de la superposition d’événements multiples. Les éléments majeurs perdus durant l’altération sont le Si, le Na, le Mn et le Mg. Les éléments mineurs et traces perdus durant l’altération sont le Co, le Li, le Sc et possiblement le Sr, le Ni et le Zn. Les éléments mineurs et traces enrichis comprennent l’Au, l’Ag, l’As, le Sb, le S et possiblement le F, le Cu, le Pb et le Zr. Étant donné sa proximité géographique, les contraintes temporelles et les similitudes de leurs assemblages minéraux, la minéralisation aurifère de l’Anomalie A est interprétée comme un équivalent distal de la minéralisation aurifère associée aux intrusions du gisement avoisinant de la zone principale (Main"

Jan 1, 2008

THE art of mine surveying has made very great progress in recent years, and is still advancing, perhaps faster than any other branch of surveying. The scope of the mine surveyor's duties has greatly increased, his instruments and methods have improved, the responsibility of his position is greater, and the end is not yet in sight.It might be supposed that such a steadily growing subject would have an adequate literature, but this is by no means the case and outsiders commonly judge mine surveyors by their text-books. Hardly any condemnation can be too strong for most of these books. The English books truckle to the antiquated and crude methods apparently still in use in England, and thereby largely aid in perpetuating them; they commonly in illustrative examples give the distances in fathoms, feet, and inches; they spend page after page discoursing on instruments that should have been forgotten long ago; they try to antagonize theory and practice by detailing such calculations as that a certain vein will contain 2,003.907 pounds of galena per square fathom, and then reduce this amazing quantity to hundredweights, quarters, and pounds. Nothing can be more unscientific, or, for that matter, less businesslike, than unwarranted assumptions of accuracy; it is, perhaps, the greatest curse of applied science. Here we have a calculation to thethousandth part of a pound, when there is probably an unavoidable error of two hundred pounds. What shall we say of a man who explains how to measure the depths of shafts to the hundredth part of an inch by means of short brass rods screwed together...

Jan 1, 1909

The addition of cement to underground backfill at The Zinc Corporation, Limited and New Broken Hill Consolidated Limited, Broken Hill commenced in 1967. A deterioration in metallurgical performance at each concentrator occurred as a result, with increased loss of lead and zinc to residues. Investigations to determine the reasons for this problem and methods to counteract it have been undertaken. This paper outlines the effects of cement on lead-zinc beneficiation at Broken Hill and presents an interim report on attempts to overcome the metallurgical deterioration.

Jan 1, 1971

By Fernanda da Silva Machado

Em um mundo de recursos naturais decrescentes, com a intensificação das indústrias automatizadas de todos os tipos (I4) e contínuo aumento da população, é necessário desenvolver melhores caminhos para a geração e distribuição de riquezas. Uma das alternativas para este objetivo é o conceito da Economia Circular. Este artigo apresenta um exemplo focado na intensificação do uso de resíduos de biomassa na produção integrada de aço exclusivamente baseada na combinação de reatores industriais existentes em um layout que favorece o conceito da economia circular. O ferro também é obtido do processamento tradicional de sucata, reprocessamento de resíduos de ferro e óxidos de ferro, como a escória, pequenos óxidos de ferro, reversos metálicos, resíduos da indústria siderúrgica integrada tradicional. Os resíduos de biomassa são provenientes da demolição de casas de madeira, e outros resíduos de biomassa, como limpeza florestal para evitar-se incêndios, resíduos de moinhos, paletes usados e qualquer outra fonte de biomassa. As combinações dos reatores tornaram-se possíveis devido à nova versão do processo de Carbonização Contínua, Carboval, um reator especialmente projetado da tecnologia Lambiotte tradicional, para produzir, de preferência, o carvão vegetal que possui as mesmas características necessárias para alimentar o Mini Alto Forno tradicional a base de carvão.

Oct 30, 2017

By Christian J. Sorensen, Christopher Armstrong, Andrew Matejunas

A team consisting of junior and senior mechanical engineering students at New Mexico Tech worked on the design of an explosively loaded vessel, with a maximum load of 15 grams (0.53 oz) TNT equivalent explosive. The main challenge presented was to meet the stringent sample positioning specification of 3 microns in two Degrees Of Freedom (DOF) and one degree of rotation in a third DOF. This is to accommodate precise sample placement in a tight x-ray beam, and to bring areas such as explosives/metal interfaces into magnified field-of-view photography. This presentation describes the process and design decisions to arrive at the final product presented to LANL in December 2014. Our engineering analysis techniques will be reviewed, including use of American Society of Mechanical Engineers (ASME) Boiling & Pressure Vessel Code (BPVC) Code Case for Impulse Loaded Pressure Vessels (ASME BPVC Code Case 2564-3). Also discussed will be integration of Hydrocode computer models with Finite Element Method analysis.

Jan 1, 2015

By D. Govender

In recent years, economies of scale have continued to drive copper projects to larger throughputs to offset depleting lower grade resources. A decade ago there were only a small number of projects that stretched beyond 100,000 Mtpd throughput rates. Nowadays and moving forward virtually all the major copper projects are sized beyond this, with throughput rates up to 250,000 Mtpd now under evaluation for a number of key projects in Chile and Peru. This paper explores the development from the 160 m3 flotation cells, through to the 257 m3 cells and nowadays to the 660 m3 machines. The contributions of specific copper concentrators to this growth phase are reviewed herein. The historical basis of flotation machine scale-up is also briefly discussed. Metallurgical results as well as layout, maintenance and operational aspects are highlighted.

Feb 27, 2013

By Axel Sahlin

Jan 1, 1898

By M. Hancer, J. D. Miller

It is known from soluble salt flotation practice that the K, Mg double salts of kainite (KClMgSO43H2O), and carnallite (KClMgCl26H2O) are difficult to float and must be converted to other salts such as schoenite (K2SO4MgSO46H2O) and sylvite (KCl) in order to recover potash values. The flotation characteristics of these double salts have now been confirmed in some detail by carefully controlled laboratory experiments with both cationic and anionic collectors. The experimental results are discussed in view of recent experimental findings regarding the flotation characteristics of simple salts, in which the flotation response was shown to be determined by the interfacial water structure and whether the salt could be considered to be a water structure maker or a water structure breaker. The same approach can be use to explain the flotation response of the potassium double salts ; schoenite, kainite, and carnallite. In addition, the sign of the surface charge of schoenite (K2SO4MgSO46H2O), was determined as a function of pH from nonequilibrium electrophoretic mobility measurements. Schoenite appears to exhibit three charge reversals (CR) which can be explained based on surface hydrolysis reactions. The flotation behavior of schoenite is further considered based on solution chemistry calculations, electrophoretic mobility measurements, and microflotation results.

Jan 1, 2001

By Larman J. Heath

Wellbore enlargement was tested using hydrazine hydrate in a gas-storage well in Ohio to increase the well productivity. The wellbore was to be enlarged by chemical disaggregation of the sandstone adjacent to the wellbore. Productivity immediately declined 49.1 percent and gradually declined to zero in 7 months. A down-hole camera survey showed a white-to-gray precipitate covering the entire wellbore surface. The precipitate was chemically analyzed and identified as mostly carbazic acid, a hydrazine derivative of carbonic acid. Formation of this precipitate was not anticipated; this viscous sub-stance caused the gradual loss in productivity of the well. The wellbore was not enlarged. Laboratory tests were run to determine what clay stabilization measures could be taken in sandstone cores to prevent clay swelling and particle migration caused by hydrazine hydrate. Normal clay stabilization methods did not prevent the virtually complete loss in permeability to hydrazine hydrate. Other laboratory tests using natural gas diluted with small amounts of carbon dioxide confirmed the ease with which carbazic acid could be formed in a hydrazine hydrate-saturated environment within and adjacent to the wellbore.

Jan 1, 1970

By Grant P. Cordon

Our subject, "Safety, Legal, and Contracting," is a range of topics which covers a broad spectrum, but is obviously Intended to focus our attention upon certain particular aspects of tunnel problems. These are all fascinating and complex subjects, and others are much more qualified to discuss to discuss the fine points involved. Put after some 45 years' involvement as an inspector, engineer, contracting officer, and especially for the last 22 years as a contractor's estimator and manager, I have developed some strong and definite convictions to share with you. I hope it will serve to get you started thinking. My first tunnel experience was in a soft ground tunnel which was dug by hand, literally. The crown or arch back was taken out, a pebble at a time, by bare hand. The face was constantly breast-boarded, and the mucking was all done by hand shovel. My first rock tunnel was drilled by hand held drifters from the muck pile. Since then, most tunneling techniques have improved greatly. The jumbos, booms, muckers, and moles have taken over many of the back-breaking chores, and reduced the manpower requirements.

Jan 1, 1974

In the 1980s and?90s the gold mining industry in South Africa came under pressure from the continued poor dollar gold price and escalating Rand based costs, furthermore the external impacts on the industry were changing. Thus, the Chamber of Mines (COM) shifted its focus away from many historical areas of support towards the new industry challenges in safety and health, labour markets, environmental responsibility, mineral rights legislation and social responsibility. During 1997 the lack of funds and the changes facing the tertiary institutions were often subjects of discussion at the various sub-committee meetings. The Metallurgical Sub-committee of the Chamber Education Fund or the Sub-committee of Consulting Metallurgists as it was known identified the need for the funding structure to change with the times. Up to this time the Chamber of Mines operated an Education Fund that supported mining industry academic departments at various South African tertiary institutions; these funds were derived exclusively from the country?s gold and coal mines the basis of Chamber membership. Funds of less than R5 million per annum were available for distribution by the three disciplinary sub-committees of mining, metallurgy and geology.

Jan 1, 2003

By H. Kenworthy

This report concerns cooperative milling investigations of the Central mill of the Eagle-Picher Mining &. Smelting Co, The work carried on at the Central mill and the Rolla, Station shows that: It is possible to reduce the Central mill heavy-medium plant tailings by 0.05 to .15 percent zinc; the 3/16-inch to 10-mesh fraction of the jig feed can be treated by sink-float to obtain a tailing containing only half as much zinc as the jig tailing; Humphreys spiral concentration of the flotation tailing does not recover enough zinc to be economically attractive; and crushing and wet grinding of ferrosilicon for heavy medium are commercially feasible. The Eagle-Picher Co. operates extensive mines in the Tri-State area of Missouri, Kansas, and Oklahoma. The ore is milled at its Central hill, which also accepts custom ores. During the recent war the mill handled about 12,-000 tong- of low-grade ore per day. The company milled about 50 percent of the district tonnage and purchased nearly 90 percent of the custom ore. About 50 percent of the mill feed was from company mines. Zinc is the chief value in the Tri-State ores,-with Varying quantities of lead and cadmium minerals, as well as small amounts of germanium and gallium.

Jan 1, 1949

By G. R. Dunning, M. R. Wilson

"Abstract - The early Paleozoic accretionary tectonic regime that was established along the Laurentian margin of the Newfoundland Appalachians provided a favorable setting for shear-hosted gold mineralization along a major terrane suture, the Baie Verte-Brompton Line. The Stog’er Tight prospect is one of several mesothermal-style gold occurrences hosted by shear zones within accreted ophiolites and oceanic arc terranes on the Baie Verte Peninsula. It is an epigenetic, stratabound deposit that is confined to shallow-level gabbro sills within the volcanic cover sequence of the allochthonous Point Rousse ophiolite complex. Gold mineralization at Stog’er Tight is associated with hydrothermal mineral assemblages represented by chlorite-calcite, sericite-ankerite, red albitepyrite (±Au) and chlorite-magnetite alteration zones. Gold occurs with pyrite within the intensely altered gabbro, along the margins of syn- to late-shear, quartz-rich, replacement veins.The Stog’er Tight gabbro served as a rigid body conducive to shear deformation and fluid penetration, whereas, its high Fe-Ti oxide content induced fluid oxidation and gold-pyrite precipitation. Hydrothermal alteration involved progressive CO2, S, Na, and LILE metasomatism, along with significant enrichments in the REE, HFSE, and Th in the high-grade ore zone. Temperatures of vein formation and alteration are constrained by oxygen isotope thermometry to be between 250°C and 480°C. Isotopic compositions of vein quartz from the Stog’er Tight prospect are uniform (??O = +12.5 ± 1‰) and fall within the range cited for many shear-hosted, auriferous quartz veins.A U-Pb zircon igneous age of 483 +3/-2 Ma for the Stog’er Tight gabbro is consistent with its stratigraphic correlation with other Ordovician ophiolitic and volcanic arc/back-arc assemblages in Newfoundland. The U-Pb age of a rare variety of hydrothermal zircon recovered from the high-grade ore zone directly constrains the timing of gold mineralization to 420 ±5 Ma, in accord with a major orogenic episode of Silurian age that produced many of the magmatic and metamorphic rock suites in north-central Newfoundland. Our results are consistent with a post-peak metamorphic, late-magmatic model for gold mineralization that occurred during the waning stages of Silurian orogenesis, driven by emplacement of I-type granitoid intrusions into the crust."

Jan 1, 2000

By Peter Zhang

Shield recovery in a longwall move is normally conducted from tailgate to headgate. However, if the face is wide and the immediate roof is weak, difficult conditions with considerable roof sag, excessive shield load, and local roof falls could occur as the shield recovery proceeds to the middle of the face, causing delays in shield recovery. The situation could be aggravated when a pre-driven longwall recovery room is employed. Alternatively, a bi-directional approach for shield recovery, i.e. shield recovery starting from the middle of the face towards both tailgate and headgate, can alleviate the roof sag significantly by quickly withdrawing the shields towards the lower abutment pressure zones at the headgate and tailgate sides. In this case, the bi-directional shield recovery approach was used in a longwall move for a 1450 ft wide face under weak roof conditions. Shields were successfully withdrawn within five days without experiencing significant roof sag. The time-dependent roof-to-floor convergence, shield pressure, and roof conditions were monitored during shield recovery. 3-D finite element modeling was conducted prior to longwall move to evaluate the difference between a uni-directional and a bi-directional shield recovery during a longwall face move. Vertical stress, yield zone in and around the recovery room, load on the shields, and convergence at the center of the shield canopy were obtained from computer modeling, and compared with the data from field monitoring. Finally, the advantages of the bi-directional shield recovery are discussed.

Jan 1, 2007

By M. W. Von Bernewitz

The Bureau of Mines receives frequent requests for information on the treatment of mercury ores, but as its own and almost all other publications on mercury are out of print, the Bureau has prepared this circular on the metal for the prospector and operator of small mines and plants. Mercury, commonly though improperly termed ?quicksilver?, is the only common metal that is liquid at ordinary temperatures. Mercury is used in the amalgamation of gold and silver, in power boilers, explosives, friction-less bearings, laboratory apparatus, lamps, medicine, paint, rectifiers, and for ?silvering.? The last mentioned is being superseded by silvering with silver. The use of mercury boilers may increase when they are thoroughly understood, but amalgamation is -being replaced to some extent by the use of corduroy and other collecting mediums, such as jigs and flotation cells.

Jan 1, 1937

IN concentrating mills, where several millerals are recovered for realisation in more than one product, various systems are used to express the relative economic value of the work done, and, in the hope that it may prove of use to other operators, the writer will describe a system which, in his opinion, is more complete than any other that he has seen published.The controlling factor in all mill work must be based on the economic result represented by the greatest margin possible between the realizable value of the products and the cost of obtaining same.From a mill-man's point of view these are affected by the following factors:1. Metal contents of ore.2. Grade of products.3. Recoveries.4. Working costs.The grade of ore milled is usually outside the mill-man's control, but this may exercise a considerable influence on the grade of his products, metal recoveries, and revenue per ton of ore. Higher grades or recoveries may be obtained by using a more expensive process, or by additional grinding or reagents, and the economic comparison can only be arrived at by obtaining an analysis showing the monetary value of each variation within the possible limits.In the system to be described, the value of unit variations of metal contents of the ore, grade of products and recoveries are calculated in terms of a monetary unit per ton of ore with the returning charges ruling, and any suitable metal prices. To do this it is necessary to assume what, for convenience, is termed a "standard" set of results from the mill, preferably representing about average conditions, and having calculated the effect of unit...

Jan 1, 1931

The roasting of sulphide ores and concentrates is often the first step in the production of metals or chemicals. In many processes, the production of sulphuric acid is viewed as a by-product, whereas in some plants production is an important economic factor. Regardless of the purpose, a pyrite roasting plant consists of mainly three plant sections: roasting, gas cleaning and sulphuric acid. With the addition of air, the pyrite concentrates are transformed into solid oxides and gaseous sulphur dioxide at temperatures of 600?1000°C. After cleaning and cooling, the sulphur dioxide in the roasting gas is further processed to sulphuric acid. Two types of reactors are used depending on the application: stationary or circulating fluid bed. For over 60 years, Outotec has progressively been developing the principle of fluidized bed technology in several different reactor types for a multitude of process applications. The versatility of the fluidized bed reactor system has manifested itself in the treatment of minerals, including solid fuels, and for metallurgical processes both in the ferrous and non-ferrous fields. Process applications have included roasting, calcining, combustion and charring of coals, as well as off-gas treatment. This paper provides a summary of the pyrite roasting technology currently used along with a simple cost comparison of pyrite roasting and sulphur burning processes.

Jan 1, 2009

From a vast army of workers to gargantuan machines to immense volumes of material being moved, almost everything about the Port of Miami Tunnel (POMT) project points to tunneling on a massive scale. Almost.The star of this underground and underwater show is a Herrenknecht tunnel boring machine (TBM,) nicknamed ?Harriet? by a local Girl Scout troop. With her 12.9-m- (42.3-ft-) diameter cutting head and a total length of 139 m (457 ft), Harriet is boring through thousands of cubic meters of clay, dirt and sand, which is often mixed with coral and other materials, to create two 1,280-m (4,200-ft) traf?c tunnels connecting Watson Island and the Port of Miami (Dodge Island) beneath Biscayne Bay, FL. But in the midst of all of the oversized equipment and machines, a strong contender for the best supporting nod goes to a relatively tiny machine: the Brokk 400. Bouygues Civil Works Florida crews are using the compact, remote-controlled and electric-powered machine to excavate five cross passages between the twin traffic tunnels. The pas-sages will be essential to the safety of people who drive their vehicles under the bay every day.

Sep 1, 2013