Search Documents

By L. Sh. Tsemekhman

The results of laboratory, large-scale laboratory and commercial scale investigations regarding the process of slag melts cleaning by oxidizing-reduction gas mixtures with a wide range of Po2 and the use of matte of various compositions as an extracting phase are presented. The copper, nickel and cobalt behavior during the cleaning process has been studied based on SEM and x-ray Microprobe of the quenched slag melts. The general cleaning mechanisms have been found. On the basis of the obtained data the most efficient cleaning methods have been proposed.

Jan 1, 2003

By Xu Zhang, Xuewei Lv, Guibao Qiu

Slag foaming phenomenon is of vital importance to the mass and energy transfer in metallurgical processes. A considerable extensively studies carried out via out-gas in the past cannot simulate well the foaming phenomenon formed in the blast furnace where high TiO2 iron ore is used. A gas reaction was designed in the water-glycerol system to simulate the inner-gas system. This study investigated the influences of solution viscosity, particle concentration and particle size on foaming caused by endogenetic gas. The results show that the foaming height decreases with the increase of solution viscosity, which means reduced foaming ability, more difficult foaming elimination process and prolonged time for natural defoaming. With increasing the solid particle content, the foam height presents a trend which increases firstly and then decreases. Under a certain solid particle content, foaming height decreases with the increase of solid particle size, indicating a weak foaming ability.

Jan 1, 2015

By Masayoshi Matswnoto

The Kosaka Smelter and Refinery produces copper and lead, and has a history of more than 100 years as a metallurgical department of Dowa?s Kosaka Mine. The Smelter treats complex sulfide concentrates which are difficult to smelt. Valuable metals are recovered using various processes developed by Kosaka Smelter and Refinery. Effluent waters from the smelter contain large quantities of heavy metals. This paper describes how Kosaka Smelter and Refinery recovers valuable metals from various effluent waters and handles overall waste waters in order to meet strict environmental standards.

Jan 1, 1993

By Xia Hong-ying, Peng Jin-hui, Zheng Zhao-qiang, Zhang Li-bo

"Preparation of activated carbon from the walnut shell by microwave assisted steam activation was studied. Influences of the three parameters, activation temperature, activation duration and steam flow rate on the adsorption capacity and yield of walnut shell activated carbon(WSAC) were investigated,optimization process was obtained by the Response Surface Methodology (RSM). The optimum preparation conditions were as follows: activation temperature of 980°C, activation duration of 41 min and steam flow rate of 1.66 ml/min. The optimum conditions resulted in an activation carbon with an iodine number of 1025 mg/g and a yield of 52.17%, while the BET surface area, total pore volume and average pore diameter of WSAC were 1328m2/g, 0.72ml/g and 2.2nm respectively. The study supported the potentiality of comprehensive utilization ofWalnut shell and the benefits of the microwave heating.IntroductionActivated carbons are one of the most important adsorbent materials in modern society because of its abundantly developed pore structure, strong adsorption ability, high surface area and thermo stability. They have extensive application in many industries fields which include gas purification [1], catalyst supports [2] and other pollutants [3]. However, in recent years, the industrial production of activated carbon is facing the problem of raw material scarcity and high cost, which limit to be widely used. Therefore, the selection of an appropriate precursor plays an important role and it has become hot sport to seek cheap raw material to lower preparation cost. As a kind of reproducible resource, the waste from agriculture and forestry is a high-grade raw material for preparing activated carbon due to is high carbon content, such as palm shell [4], rice hull [5], and coconut shell [6]. At present Walnut shell is widely accepted to be a renewable source of biomass. According to statistics, there is more than 1000,000 tonnes of walnut shells are produced in China annually [7]. As a good precursor for activated carbon production, Walnut shell is a major agricultural waste, to make better use of the cheap and abundant agricultural waste, it is proposed for activated carbon production."

Jan 1, 2014

By Javier Antoñanzas, Susana Caballero, Eduardo Fernández, Jorge Aragón, Juan Carlos Múgica, Lourdes Yurramendi

Air Pollution Control (APC) residues treatment by plasma was studied as a technology for vitrification. During the project a protocol to verify the plasma technology was developed and afterwards applied to a specific case study: the APC residues from Municipal Solid Waste Incinerators (MSWI). Different operational conditions were tested and the vitrified products obtained were analyzed using standardized leaching tests in order to evaluate their new properties concerning safety storage. Two leaching tests were used for the evaluation, the European EN 12457-4 compliance test for leaching of granular waste materials and the French XP X 31-211 test for the determination of the leachability of a solid waste material initially massive or generated by a solidification process. Finally, conclusions about the environmental performances of the technology were obtained.

Jan 1, 2008

By Young-Chul Kang

The Onsan Copper Smelter of LG-Nikko Copper Inc. is a unique plant, which has been operating two smelting processes since 1998. The operation of the first one was started in 1979 with a capacity of 80,000tpy of copper in concentrates utilizing Outokumpu flash-smelting technology. The other one was started in 1998 based on Mitsubishi continuous process with a capacity of 160,000 tpy of copper in concentrates. Through several expansion projects, the total smelting capacity of both processes is expected to reach 430,00Otpy of copper in concentrates towards the end of 2002. This article describes operation advantages of having two different processes at one plant and comparative operation results in terms of productivity, impurity distribution, energy consumption and environment issues and etc.

Jan 1, 2003

By Federico Chavez

The process for recovering lead from battery residues used in several Mexican Plants include lead blast furnace and rotary furnaces. The formers are basically fed with recycled batteries together with the necessary additives to produce metallic lead. One of the by-products generated in the blast furnace is a dust mainly formed by lead sulfide. The rotary furnace is used to recover lead .from lead batteries, dross from the refining-alloying process and the leady fines produced in the blast furnace. This paper describes thennodynamic analysis made to the rotary furnace process to understand the effect that each component of the system has upon the lead recovery. In order to enhance the process, the influence of iron chips composition and excess coke on slag viscosity is discussed. A computer optimization program . has been developed to design the furnace charge based on material and energy balances, .together with the thennodynamic equilibrium calculation.

Jan 1, 1995

By K. Yamaguchi, Y. Takeda

"Partial pressure - temperature - composition correlation diagrams of the Ga-As, In-As, Ga-P and In-P systems were contracted based on the obtained experimental data of the phase diagram and thermodynamic properties for the III-V systems. The total vapor pressures of arsenic or phosphorus at melting point of GaAs, InAs, GaP and InP were determined as 101, 10.1, 1510 and 253 kPa, respectively, at the corresponding melting points of 1509, 1211, 1739 and. 1336K , These diagrams are applied to the analysis of the horizontal Bridgman method and the liquid phase epitaxial growth technique. On the other hand, the analysis of the equilibrium state of the. chloride-CVD process was carried out using the data of the Gibbs energy of the compounds obtained by· authors.IntroductionThe group III-V compound semiconductors ate important materials used in optoelectronic liquid high speed electronic device. The crystal growth of the III-V compounds can involve processes that require contact between the solid, liquid and vapour phases at near equilibrium condition. Examples of processes that involve contact between the solid, liquid and vapour phases include bulk crystal growth such as the horizontal Bridgman and the liquid encapsulated Czochralski method and liquid epitaxy, and between the solid and vapor include chemical vapour deposition and molecular beam epitaxy. Therefore, the knowledge of the phase diagram and thermodynamic properties for the III-V binary alloys is essential for the analyses of crystal growth techniques of III-V compounds.For these reasons, a series of different · types calorimetric measurements had been carried out: (1) The heat contents of alloys for the Ga-As, In-As, Ga-P and In-P systems by a drop calorimeter [1;2,3]; (2) the heats of formation of the GaAs, InAs, GaP and InP compounds by a twin solution calorimeter [4]; and (3) the standard entropy of these compounds by an adiabatic calorimeter [5]. Based on the third law method, the Gibbs energies of these compounds were derived from the heat capacity, standard heat of formation and standard entropy data obtained by authors. Integral molar thermodynamic quantities of the liquid III-V .alloys were also determined from combining the heat contents of alloys with standard heat of formation and standard entropy data of the compounds· by applying the thermodynamic analysis method developed by Oelsen [6]. In the present study, the thermodynamic calculations for the crystal growth processes of the III-V compound were carried out using newly experimental data of the phase diagram and thermodynamic .properties measured by authors"

Jan 1, 2000

By Keiji Okumura, Jiayi Shan, Jian Yang, Masamichi Sano

"A new method of deoxidation and desulfurization of molten iron with magnesium vapor has been developed. An immersion tube, which was filled with pellets of the mixture of magnesia and carbon powders, was put into the molten iron. Magnesium vapor produced by carbothermic reduction of magnesia inside the tube was injected directly into the molten iron with argon carrier gas. The effects of temperature and carrier gas flow rate on deoxidation and desulfurization were investigated. A mathematical model of the reactions was developed. The rates of deoxidation and desulfurization were controlled by mass transfers of magnesium vapor in the gas-phase and oxygen and sulfur in the liquid-phase. This method may offer high efficiency for magnesium deoxidation and desulfurization of molten iron.IntroductionMagnesium is a strong refining agent in steel-making processes1 • At steelmaking temperatures, magnesium has a very low solubility in liquid iron, and a very high vapour pressure2 • Deoxidation and desulfurization with magnesium take place essentially through the interaction of magnesium vapor with oxygen and sulfur dissolved in molten iron, and magnesium can change chemical composition of nonmetallic inclusions3 • However, addition of magnesium to the steel bath is dangerous and does not give high efficiency in the refining process4 • Furthermore, as a refining agent, the price of magnesium is higher than aluminium and CaO fluxes. In the present study, a new method of the deoxidation and desulfurization of molten iron was developed using magnesium vapour in-situ produced by carbothermic reduction of magnesium oxide. Pellets made of mixture of magnesia and carbon powders were charged into an immersion tube, which was made of alumina or graphite. The magnesium vapor was injected directly into the melt. The effects of pellet mass, experimental temperature and carrier gas flow rate were studied on the refining rate. A mathematical model of the refining reaction was proposed on the basis of the experimental results."

Jan 1, 2000

By Kang-In Rhee

A series of processes to recover the gold from electronic scrap which contains initially about 200-600 ppm Au have been developed. First, mechanical beneficiation including shredding, crushing and screening was employed. Results showed that 99 percent of gold component leaves in the fraction of under 1 mm of crushed scrap and its concentration was enriched to about 800 ppm without incineration. The scrap was leached in 50% aqua regia solution and gold was dissolved completely at 60°C within 2 hours. Other valuable metals such as silver, copper, nickel and iron were also dissolved. This resulting solution was boiled to remove nitrous compounds in the leachate. Finally, a newly designed electrolyzer was tested to recover the gold metal. More than 99% of gold and silver were recovered within an hour in electrowinning process.

Jan 1, 1995

Smelter operating and environmental requirements demand high on-stream time (high reliability) from the primary smelter sulfur retention device - the sulfuric acid plant. The key to reliable smelter sulfuric acid plant operation is the gas cooling and cleaning system. Problems in the gas cleaning system cause corrosion, plugging, equipment failure, etc - plant down time, in the contact section of the plant. The last fifteen years have seen major changes in gas cleaning system design to the current standard of brick lined venturi scrubber, packed gas cooling tower with plate type liquor coolers and lead or plastic tube precipitators. The current-design offers improved impurity scrubbing along with increased reliability. In addition, a number of alternate gas cleaning systems have been offered. Chematics LAB System: Monsanto DuPont Dynawave System; Lurgi venturi scrubber with lead star gas cooler. This paper will review the design and operating advantages, disadvantages, and risk of the standard gas cleaning system and compare it to the alternate systems.

Jan 1, 1992

By Richard B. Stein

Bechtel's BEMSIM computer program is a useful tool for solvent extraction-electrowinning plant design optimization. Its power (up to 90 stream components, 240 process streams, 180 process steps) has been applied to investigate floweheet configurations in order to perform basic engineering, sizing of plant equipment and to optimize performance of commercial-size copper plants. Flowsheet variations presented include series, parallel and series-parallel extraction stages, while heat balances simulate operations in summer and extreme winter conditions. The BEMSIM program has also been applied to nickel-cobalt, gold and manganese extraction.

Jan 1, 1993

By F. J. Tavera

The column flotation technology, at first developed for application in mineral dressing, has received special attention in processing of non-mineral dispersions as a result of its low cost, high efficiency and relatively simple operation. This paper presents the results from the operation of a laboratory flotation column for the separation of vegetable oil and soap from aqueous industrial effluents, The flotation system was operated under continuous countercurrent conditions without and with additions of a cationic collector. The experiments show that it is possible to separate about 80% of the organic phase in a rougher flotation stage. These results suggest that the recovery of the organic phase is highly dependant on the dispersion characteristics (i.e. bubble size, gas holdup and bubble surface area flux) and the existing an optimum bubble size from which either smaller or larger, the recovery of the organic decreases.

Jan 1, 2003

By Itavahn Alves da Silva, Izabela Diniz Duarte, Carlos Antonio da Silva, Varadarajan Seshadri

Mathematical modeling using computational fluid dynamics has been employed to assess the thermal losses in a steelmaking ladle. Thermal losses lead to thermal stratification and convective flow inside the ladle. The effects of preheating, mineralogical and physical characteristics of the lining as well as thickness of slag cover have been studied and the results obtained from application of the model have been discussed.

Jan 1, 2016

By Eren Hüseyin Obuz

In this study, the leaching kinetics of rare-earth elements were investigated using HCl and HNO3 solutions. A standard crushed complex ore was utilized as raw material. The complex ore (particle size of under 54 μm) contains REE (Ce, La, Nd, Pr, etc.). Different leaching durations were selected for the kinetic studies. The highest leaching efficiency was obtained in HCl solution, and the leaching mechanism was identified to diffusion through a product layer. The rate constants of Ce, La, Nd, and Pr were calculated as 1.08 × 10−2, 0.86 × 10−2, 1.87 × 10−2, and 1.34 × 10−2 h−1, respectively.

By Okechukwu Anopuo, Gerhard Tober, Petra Maier

"In this study, an investigation on the microstructure of hot rolled steel S355J2+N was conducted to optimize process parameters of complex forming, which combines rolling and bending. The best sets of parameters are worked out based on homogeneous mechanical properties and microstructure within the varied deformation degree with maximum at <p = 1.14 on a 25 mm thick plates. Mechanical properties, especially of heavy plates, are strongly influenced by the local deformation degree, strain rate and temperature. Detailed microstructural analyses showed that the ferrite-pearlite band structure changes near the surface, while maintaining homogeneous microstructure within the deformed work piece. Surface decarburization was also observed and this leads to decrease in hardness. To minimize iron oxide formation which could lead to side cracking, reduction in exposure time to temperature was suggested. On the other hand, temperature reduction below a critical value would risk the accurate forming process.IntroductionThis work presents the preliminary results of research to develop a new complex deformation process of thick steel plates. Complexity is given because the forming process combines rolling to reduce thickness and profiling by bending. The work piece will experience a thickness reduction from 25mm to 8 mm and is double curved. To explain and understand forming of thick plates basics of sheet forming as well as massive forming need to be used. At the moment there is no forming process established to produce double curved plates including reducing thickness in one process step. Technologies nowadays consist of two process steps: flat rolling and pressing in shape. Due to good weldability and formability the final product will be made of steel S355J2+N. This low-carbon steel is well understood and has a low strengthening exponent, which is expected to keep the forming forces down. Reduction of thickness from 25 mm to 8 mm gives furthermore a high deformation degree. Thus, hot forming has to be applied. The determination of process parameters is the main aim of overall research project; temperatures above lOOO°C are expected. Flow curves in literature are given at various temperatures and strain rates [1]. However, experiments with data close to the industrial application are rarely found, especially at low strain rates and high deformation degrees. Pre-test were done by flat rolling, being aware that the influence of bending is eliminated. The microstructure evolution were characterised in relationship to material formability with special attention to grain size change and recrystallization. Representative samples should be selected from specific locations in the deformation zone according to the knowledge about the metal forming process [2]. Due to no further alloying elements in S355, no precipitation hardening is expected to take place during hot forming, which keeps the mechanisms simple and the concentration on the feasibility of the complex forming process is given."

Jan 1, 2012

By Jin-tao Gao

In order to recover Ti resource from titanium bearing blast furnace slag, a new technology to separate perovskite phase from CaO-TiO2-SiO2-Al2O3-MgO system by supergravity is researched. In the condition of gravity coefficient of 750g, treatment temperature of 1305°C and time of 20min, the significant layers appear in samples which are obtained by means of centrifugal treatment. Along the direction of the supergravity, the volume fraction of perovskite phase increases gradually, and the equivalent diameters of perovskite phase crystals increases with the area approaching to the bottom of the sample. It is indicated that TiO2 is enriched in the bottom of sample as concentrate with a recovery ratio of 74.05% by supergravity treatment.

Jan 1, 2014

By Kim Verbeken, Evelien Van de Steene, Marc Verhaege, Jeriffa De Clercq

"AbstractThe industry is confronted with stricter discharge levels and an increasing awareness to avoid toxic waste (such as heavy metal containing sludge obtained in physicochemical water treatment) and recover valuable metals. This can be realized by ion exchange or by electrodeposition. Both techniques however show an optimum concentration range to efficiently remove and/or recover metals: electrolysis can recover the metal in its metallic form but suffers from low efficiency when applied to diluted solutions, whereas ion exchange can only be applied economically in the low ppm range.A combination of ion exchange followed by electrodeposition was applied to an industrial wastewater. The strong acidic ion exchange resin was stripped with H2SO4 giving a solution of 9g/L nickel. From this solution, nickel was electrodeposited in an ammonia buffer on a Ti-mesh cathode with high current efficiency. It is shown that organic compounds (surfactants, brighteners, …) present in the industrial wastewater do not influence the recovery process.IntroductionAlmost all rinse waters emerging from metal plating plants are generated during the washing operation of plated materials. These solutions with low metal content must either be recycled within the process or be discarded to the surface water after decreasing their metal content to acceptable levels determined by the local environmental regulations, which become more and more stringent. Today, the most commonly used practice is a physico-chemical treatment (precipitation) and a resin post treatment to meet the standards. A more sustainable approach should use a technology to recover efficiently the metal or metal salt without the production of sludge and the effluent should be consistent with environmental regulations."

Jan 1, 2008

By Guanghui Li, Xuling Chen, Zhiyun Ji, Min Gan, Tao Jiang, Xiaohui Fan, Zhiyuan Yu

With the increase of proportion of biochar(without modified) replacing coke breeze, the physical strength of sinter decreases due to the faster burning speed of biochar. An investigation upon passivating biochar with boric acid was then conducted to strengthen sintering in this paper. A layer of thin film of B2O3 distributed in the surface of biochar was observed, which could reduce the contact between reaction gas and biochar. So the burning speed of biochar was decreased properly after passivation, and the combustion efficiency increased due to the inhibition of carbon gasification. The comprehensive effects of above changes could increase the maximum temperature of sintering bed, which facilitated to the mineralization of sintering mixtures. Eventually sintering indices got reinforced. Thus the indices of sinter as applying 40% passivated biochar were comparable with that of 100% coke breeze.

Jan 1, 2015

By Laszlo Kadar, J. D. Lavers

"In the continuous casting of aluminum killed steel, the tundish nozzle often experiences clogging problems. Water model studies have shown that the clogging problem is dependent on the flow pattern in the nozzle entry region. In particular, the flow can separate at the entrance to the nozzle, leading to the development of a recirculation region. Although a nozzle can be designed such that no recirculation develops, even a small misalignment from the vertical positioning of the nozzle may render the design ineffective.To reduce the possibility of nozzle clogging, the recirculation zone must be reduced or eliminated. This may be achieved by moving the fluid downwards or raising the turbulence level in the separation region. In the case of a tundish nozzle, it is proposed that this can be achieved by using electromagnetic forces.To generate the required electromagnetic force, two systems are considered. The first is based on injecting a DC current; the second by using electromagnetic induction. Both methods are described in this paper. Order of magnitude calculations are provided to illustrate that both methods are essentially feasible. The performance of each method in terms of modifying the turbulent flow characteristics in the nozzle entry region is then examined using a numerical model. It is shown that both methods can greatly reduce the recirculation zone. A cylindrical nozzle was chosen for the model studies since it represents a worst case situation.On the basis of the model studies, it can be concluded that whereas both of the proposed methods have the potential to reduce the troublesome recirculation zone, the induction method appears to be simpler in terms of practical implementation."

Jan 1, 1999