Search Documents

By Jiulong Cheng

Underground coal mining causes overburden deformation and failure, one major form of which is bed separation in the overburden. Surface subsidence can be controlled by injecting grout into the bed separations. For a long time, the grouting results of bed separation can not be validated. This is the problem in the application of this technique. This paper analyzes the conditions leading to bed separation, develops mathematical models for seismic wave fields generated before and after bed separation, and bed separations grouted with different materials, and computes the seismic wave field characteristics using the finite difference method. The results show that the existence of bed separation causes changes in the characteristics of seismic wave field, and that different grouting materials generate different seismic wave field characteristics. Intact strata, bed separation, and bed separation filled with air or water all display distinctive seismic wave field in amplitude and frequency spectra. After mining, the original location that provides strong seismic reflection wave no long exists. It is replaced by a weak and syncline-shaped reflection wave. The area, where the seam wave disappears, is larger than that of the mined area. The location, where a bed separation occurs, generates a set of reflection waves stronger than the normal one. The energy of the reflection waves varies with the materials filling the separations. Bed separations filled with air generate stronger reflection waves than those filled with water. The major frequencies for those filled with air are lower than those filled with water. Therefore, it is possible to determine the property of filling materials by analyzing and comparing the amplitude and frequency spectra of the reflection waves. Case studies of application of seismic method for exploring bed separations and grouting were analyzed. The results show that it is feasible to use seismic technique for exploring bed separations and grouting.

Jan 1, 2006

By Shosei Serata

The Stress Control Method improves productivity and safety in underground coal mining. The method stabilizes the roofs and floors of mine openings in both shallow and deep coal beds, regardless of whether or not there are ground stability problems. This paper describes the means by which a tapered pillar experiment is used to collect in situ data, which is then used as input for a computer model. The resulting computer model is then used to optimize Stress Control design for the mine under study. The behavior of any underground coal mine is not elastic, as is generally conceived in the conventional view of rock mechanics, but rather is highly time-dependent and site-specific. Unfortunately, conventional rock mechanics methods based on the elastic principle are not able to capture the highly non-elastic nature of ground behavior which actually occurs. To capture actual behavior, a new method of study is required. In this regard, geomechanical study of an underground coal mine may be compared to studying the behavior of a living fish. Its true behavior zannot be understood by examining it "dead in the laboratory. It Is the "live" nature of the coal mine that is required for design optimization of the Stress Control Method in the given mine. The Stress Control Method is based on a time-dependent theory of the global behavior of the mine ground, which generally contradicts the conventional elastic theory of ground behavior. Therefore, site-specific adaptation of the Stress Control Method required a comprehensive understanding of the global behavior of the mine as a function of time and site-specific ground conditions.

Jan 1, 1986

By Jeffrey K. Whyatt

The Crandall Canyon accident investigation included an interesting and unexplained observation by rescuers that the ?barrier rib had shifted northward as a unit, as much as 10 feet.? This is not the first mention of such a movement, although such reports are rare. Historical accounts describe unusual movement and displacement of intact coal, cribs and timbers. Two movements of particular interest are the creation of gaps above coal pillars and falling of standing support elements without apparent damage. A dynamic boundary element program was used to explore movements induced by slip on geologic features removed from the affected panel. While the resulting models are much too simple to fully replicate these observations, they do show that the types of phenomena observed are possible. They can also provide insight into the types of motions that ground support elements are subjected to during large bump events. This was demonstrated for the case of a large bump in a Book Cliffs coal mine. Seismic information suggested the source mechanism to be normal slip on a fault. A model of that source showed initial dilation of the panel followed by dynamic compression and rebound ? consistent with underground observations. The initial dilation is important as it may allow slender standing support to shift or fall.

Jan 1, 2009

By D. C. Oldroyd

Western Coalfield?s Tandsi Mine, has difficult support conditions and a history of roof falls, resulting in mining roadway widths and depths being restricted for safety reasons. Rock Mechanics Technology Ltd was contracted to improve the support system to allow the introduction of mechanised room and pillar mining. The introduction of a ?world best practice? bolting system resulted in major improvement in roof stability, allowing mining restrictions to be lifted and Tandsi to become one of the first two Indian mines to introduce a mechanised continuous miner system. The first year?s production was some six times previous levels. Because of the improvement in the support system, RMT was also able to design a partial de-pillaring system suitable for the Tandsi continuous miner districts together with the introduction of monitoring procedures and guidelines to maintain safe roof support conditions. In situ monitoring of pillar and roof behaviour was undertaken as the first pillars were extracted to confirm the design. De-pillaring operations have also proved highly productive, and to date there has been no associated support related major injury or dangerous occurrence. The success of this project demonstrates the potential for mechanised room and pillar mining in India.

Jan 1, 2006

By Rudiger Baltz

The sudden failure of bodies of rock is a serious problem commonly experienced in the international mining industry. These explosive releases of energy are referred-to as ?bumps?, ?outbursts? and ?rockbursts?. Rockbursts can occur at such a rapid speed that they present a direct threat to safety in large parts of the mine workings. The build-up of excess stress within the body of rock can be attributed to different causes. In shallow workings, for example, sudden and violent failure of the roof strata can be caused by leaving insufficient pillar width when practising room-and-pillar mining. At much greater working depths, as it is the case in the German coal industry, rockbursts are generally attributable to high levels of rock pressure. This can even result in coal outbursts when driving individual roadways. More than thirty years ago the German coal industry suffered from numerous rockburst incidents which caused many deaths and serious injuries. This led directly to the establishment of the Rockburst Prevention Centre, which was created at the instigation of the mining companies and the chief mines inspectorate. The consistent logging and analysis of all rockburst incidents has led to the development of a system that is still used as a basis for preventing underground rockbursts and minimising the risk of such phenomena occurring. Working closely with the mining authorities and mining companies the accredited experts of the Rockburst Prevention Centre have played a key role in helping to develop and implement a range of methods for the early detection and prevention of rockbursts.

Jan 1, 2008

By Guangyi Sun

Wall rock classification method for coal mine support is the main factor affecting mine support. It is greatly affected by the combined effect of randomness, fuzziness and human being's incomplete knowledge. There are several coal rock classification methods. Using different rock classification methods the same engineering rock mass can be classified into different classification leading to different construction practices.

Jan 1, 2005

By Alan A. Campoli

The U.S Bureau of Mines is conducting research to develop improved guidelines for selecting the type and pattern of roof support in different geologic environments (Mucho, et al., 1995). As a part of this wider research effort, a multifaceted ground control investigation was conducted at the Diamond TB Mine of RoxCoal, Inc. The study included statistical analysis of mine-wide roof bolt performance, instrumented bolt test areas, stress damage mapping, and pillar design analysis. The mine employs state-of-the-art continuous miner technology, including mobile roof supports and continuous haulage, to retreat mine the Lower Kittanning Coalbed. A herringbone section design makes the stability of the center belt entry critical to efficient retreat mining. Roof cutters formed during section development sometimes set up unstable immediate roof conditions in advance of the belt entry mobile roof supports during retreat mining.

Jan 1, 1996

By Kazem Oraee

Falls of ground have historically been the main cause for fatalities in underground mines. Although recent advances in technology have reduced the number of such accidents, when failures occur they usually result in severe consequences. Risks of rock falls, use of heavy machinery and electrical apparatus, entry to confined spaces, working in noisy and dusty environments, and working on unstable platforms are some of the hazards in ground control operations. Managing these risks requires a management regime involving strict adherence to operational codes of practice and an enshrined culture of safety. These should be subsequently reinforced through active participation of management, systematic training, and stringent internal and third party auditing. Accident reports show that the major contributing factor in most rock fall accidents is the failure to adequately manage known risks due to the lack of a systematic process. OHSAS 18001 (Occupational Health and Safety Assessment Series) is an international occupational health and safety management standard specification to develop occupational health and safety at the workplace. This standard is intended to help mine operators control occupational health and safety risks. Addressing the requirements of OHSAS 18001 can be a complex and demanding task. A comprehensive guide for efficient and accurate implementation of this standard is provided in this paper. The discipline can be used to establish an accountable management system foreground control activities in underground coal mines. The paper also provides guidelines for preparing necessary documents, devising safety policies, procedures, performing risk assessment, and handling instructions. Finally, the paper concludes by providing a sound analytical basis in terms of the creation of a robust safety management system foreground control operations in underground mines. Full benefits of implementing an effective and systematic operational health and safety management system are illustrated. The procedure adopted and prescribed in this paper can be used in all underground coal mines where lack of appropriate ground control practices can create deficiencies in both safety and productivity.

Jan 1, 2012

By H. J. Siriwardane

This paper presents results from three case studies involving longwall mine panels at which the measured ground movements were compared with the numerical model predictions based on the finite element method. A new approach called the "displacement approach" was used in this study. The general concept of this method is based on the assumption that total roof collapse occurs behind the mine face as it advances. This assumption appears to be true for almost all longwall mining conditions. The prediction based on the numerical model appears to compare well with the measurements.

Jan 1, 1988

By Mark K. Larson

Researchers at the National Institute for Occupational Safety and Health?s (NIOSH) Spokane Research Laboratory are developing a borehole profilometer to dynamically measure the roughness pro-file of boreholes used to install roof bolts fully encapsulated with resin. Numerical measures of roughness were calculated from profiles of borehole surface roughness to determine potential roof bolt anchorage capacity. The concept of dynamically profiling was proven through the following series of laboratory tests: a sensitiv-ity test using various grits of sandpaper, a known-profile test along a section of a concrete hole, and a simulated borehole test in a pipe with machined grooves. Two profilometer prototypes were devel-oped that measure slight changes in the radius of a borehole using either strain-gauged, spring-steel arms or rigid, steel arms attached to a spring-loaded cone and a linear potentiometer. Both instruments performed reasonably well in the laboratory and were subsequently tested in boreholes drilled in two concrete blocks using different drilling techniques to obtain three different borehole surface roughnesses. A Z2 roughness parameter was calculated with data from the first profilometer, and an average radial increment was calculated from the test results of the second profilometer. Although both instruments were able to readily distinguish the difference between smooth and rough boreholes, the correlation coefficient (r2) for a linear relationship between Z2 and average radial increment was 0.577. Pull tests were conducted with resin bolts installed in the concrete blocks, but maximum pull-out strength could not be correlated to borehole roughness because in each of these tests, failure occurred at the resin-bolt interface. A more sophisticated prototype has been designed to measure surface roughness and also accurately determine the location and tilt of the instrument in the borehole. However, this instrument has not yet been fabricated or tested.

Jan 1, 2007

By F. E. Chase

Mobile roof supports are shield-type support units mounted on crawler tracks. Mobile roof support (MRS) units are used during retreat mining, and they eliminate the setting of roadway, turn, and crosscut breaker posts which are required during pillar recovery operations. Mobiles are a more effective ground support than timbers, and their usage enhance the safety of section personnel and reduces material handling injuries. MRS usage is rapidly increasing, and approximately 40 U.S. coal mines have successfully employed this relatively new technology. This paper is in response to increasing requests from operators, State and Federal Regulatory Agencies, and others on the practical aspects of MRS usage in underground coal mines. During this investigation, nearly half of the U.S. mines which have utilized mobiles were visited. This report depicts the more common pillar extraction methods which operators have found successful. The Christmas tree and outside lift methods are illustrated and discussed. Roof control plans that do not require breaker posts or allow pillar extraction with fewer than four mobiles are also examined. In addition, operators' experiences with setting pressures, loads, and rates of loading during pillar extraction are addressed. Mining and support strategies to more effectively control hillseams, weak roof, and gob overrides which have entrapped equipment are also discussed.

Jan 1, 1996

By Christopher C. Woomer

Cyprus Shoshone Mine uses the longwall method to extract a deep, thick, pitching coal seam in the Hanna Basin of South Central Wyoming. The immediate, and main roof rock consists of weak, thinly-bedded, silty mudstones with weak, interbedded fine-to medium-grained sandstone. Tailgate ground control has been a critical factor impacting productivity at the mine. A gateroad condition mapping program for the 11 left longwall gateroads indicated potentially severe ground control problems for the tailgate. It was predicted that the existing, secondary support pattern of wood cribs would not provide adequate support capacity. As predicted, severe deterioration of the tailgate occurred in the form of a roof cutter, sloughing ribs, and failing wood cribs. Productivity was affected and additional support was required. Shoshone personnel evaluated several options for providing the additional support needed in the tailgate. The additional support system and placement method had to satisfy several requirements with respect to access, materials handling, placement method, set-up time and support capacity. Approximately 6,000-ft. of deteriorating tailgate had to be supported. The initial wood crib support system left a 6-ft. walkway for access and construction of the additional support. This access was further reduced as the roof loaded the wood cribs. This eliminated the possibility of mechanized material handling to the construction locations. All materials would have to be transported by hand. The additional support system had to be placed quickly to stay ahead of, and keep pace with, the required longwall advance rate. It had to incorporate the existing wood cribs and provide at least 500 tons of extra support capacity. And most critically, the system could not affect longwall ventilation. Longwall coordinators and engineers made the decision to use a low density, pumpable cement known to the industry as TeksealTM, to provide the system required. A 200 psi ultimate strength mix was decided on to provide the required load capacity. The existing cribs were formed with 1-in. by 6-in. boards and brattice cloth to provide the containment. To overcome the access limitations, three boreholes were drilled from the surface to the tailgate on 2,000-ft centers. A mobile pumping station was established on the surface and the TeksealTM was pumped 900-ft. down the boreholes through a 1.5-in. steel pipe, then as much as 1,800- ft. along the tailgate entry through 1.25-in. miner spray hose. The materials required for the TeksealTM supports could all be carried into the construction locations by hand. As a direct result of incorporating relatively new methods of pumping high yield, low density, cementitious grouts, the Shoshone Mine reduced downtime due to tailgate ground control problems by approximately 70% in comparison with previous Longwall panels. The longwall set three monthly production records while mining the 11 left longwall under the deepest cover, steepest pitch, and most extreme ground control conditions ever encountered at the mine.

Jan 1, 1995

By G. M. Molinda

Ground Penetrating Radar (GPR) is being investigated for the potential to determine roof hazards in underground mines. GPR surveys were conducted at four field sites with accompanying ground truth in order to determine the value of GPR for roof hazard detection. The resolution of the current system allows detection of gross roof fractures (>63 cm (s1/4 in) zone) or rider beds in coal measure roof. Data quality is not yet sufficient to detect small bed separations or subtle lithologic changes in the roof. Differences in data quality are discussed, as well as suggestions for collecting improved data.

Jan 1, 1996

By Hamid Maleki

In this paper, the authors present a review of data gathering programs and stress analyses for improving mine layout designs at BRL mines located near Paonia, Colorado. BRL and other companies have used both longwall and continuous miner methods for the extraction of the Upper D, Upper B, Lower B and C seams from the multiple-seam reserves in the North Fork Valley. Historic mining in the B and C seams has created stress footprints in the neighboring unmined seams compounded by stress transfer from recent longwall extraction in the Upper D Seam. Thus optimum positioning of workings in the remaining reserves requires careful collection of pertinent data and consideration of load transfer from previous workings through remnant abutment pillars. Based on long-term subsidence monitoring, underground mapping and stress analyses, we have confirmed initial load transfer analyses finding mild interactions between the UD and LB workings, and the mining conditions have proven to be good and manageable during the development stage of the LB Seam. This has been achieved through prudent mine planning, prudent positioning of the gateroads in multiple seam workings and support allocations.

Jan 1, 2007

By Craig Compton

Falls of small pieces of rock from between roof bolts continue to cause fatalities and to injure hundreds of coal miners each year. Roof screen is the most effective way to prevent these incidents, but some mines are reluctant to use it because they believe installing screen can be awkward, expensive and time-consuming. The most common type of roof bolting machine used in mines today is the dual boom, outside-controlled roof bolter. Mines who install roof screen using these machines have developed some machine modifications and techniques to ease roof screen installation. This paper describes some successful techniques and machine modifications that are being used in productive mines to assist with roof screen installation. Since the material handling involved with roof screen installation can expose miners to an increased risk of musculoskeletal injuries, the National Institute for Occupational Safety and Health (NIOSH) ergonomists, designed machine modifications and implemented a series of tests to evaluate roof screen handling procedures for outside-controlled, dual boom roof bolting machines. Roof screen installation can also have a positive economic impact on a mine by reducing the cost of injuries, workers? compensation, required spot or re-bolting, and clean-up of long term travel and belt entries.

Jan 1, 2007

In this paper a numerical formulation is presented for determination of the axial load along a cable bolt for a prescribed distribution of rock mass displacement. Results using the program CABLE indicate that during excavation, the load distribution that develops along an untensioned fully grouted cable bolt depends on three main factors: (i) the properties of the cable itself, (ii) the shear force that develops due to bond at the cable-grout interface (i.e. bond stiffness), and (iii) the distribution of rock mass displacement along the cable bolt length. In general, the effect of low modulus rock and mining induced stress decreases in reducing bond strength as determined from short embedment length tests, is reflected in the development of axial loads significantly less than the ultimate tensile capacity even for long cable bolts. However, the load distribution is also dependent on the deformation distribution in the reinforced rock mass. Higher cable bolt loads will be developed for a rock mass that behaves as a discontinuum with deformation concentrated on a few fractures, than for one which behaves as a continuum, either due to a total lack of fractures or a very high fracture density. This result suggests that the stiffness of a fully grouted cable bolt is not simply a characteristic of the bolt and grout used, but also of the deformation behavior of the ground. In other words, the same combination of bolt and grout will be stiffer if the rock behaves as a discontinuum than if it behaves as a continuum. This paper also explains the laboratory test programme used to determine the constitutive behavior of the Garford bulb and Nutcase cables bolts. Details of the test setup as well as the obtained results are summarized and discussed.

Jan 1, 1996

By Luis Giraldo

The installation procedure of fully grouted rebar bolts requires that the bolt be pushed through the resin grout until it is fully inserted in the borehole. Resin grout is a highly viscous fluid that is forced to flow through the annulus between the bolt and the borehole as the bolt advances. Variables such as bolt insertion speed, bolt vs. borehole diameter and grout viscosity determine the magnitude of the pressure generated ahead of the bolt tip. Under weak rock conditions, the magnitude of the pressure of bolt insertion is often sufficient to initiate hydraulic fracturing along joints or bedding planes that allow injection of grout into the strata leading to significant loss of bolt encapsulation. The grout pressure front has also been linked to gloving, a bolt installation problem that reduces bolt effectiveness. A series of tests were conducted to characterize the pressure of bolt insertion during bolt installation under various conditions. Analysis of the data shows three distinct stages of pressure build up during bolt installation. Understanding of the mechanisms involved may allow development of strategies for controlling the pressure buildup and its negative impact during roof bolting under weak rock conditions.

Jan 1, 2006

By Anthony Iannacchione

Designing coal pillars to provide resistance against overburden loads has long been an aim of rock mechanics engineers. The need for accurate pillar strength models has become more urgent as greater overburdens are encountered and pillar sizes grow larger. Current pillar design models differ widely in their predictions of the trend in pillar strength with increasing pillar width-to-height ratio. The goal of this paper is to evaluate current pillar strength theories, using a comprehensive data base of stress measurements from coal pillars. The stress measurements indicate that coal pillars maintain relatively high stresses near the ribline, and that the stress gradient within the yield zone can be approximated as a straight line. Several problems are identified for further research, including calibration procedures for different types of stress cells, strain softening behavior in the yield zone, and measurement of stresses in the cores of very wide pillars.

Jan 1, 1992

By X. S. Tan

This paper deals with the analysis of stress condition on the interface between two types of floor rock materials when the vertical stress is larger, or when the horizontal stress is larger in a rectangular opening. It indicates that the floor Failure and the failure stress of floor rocks are closely related. It also demonstrates that a larger horizontal stress is one of the most important factors in increasing the potential for floor rock failure and floor heave.

Jan 1, 1990

By Ulrich Paschedag

The WESTFALIA group of companies developer and manufactures underground mining machinery for complete high-performance longwalls. WESTFALIA uses a state of the art electrohydraulic system as the most important component for the realisation of today's fully automated plow or shearer longwall. The shield control unit (SCU) allows maximum custom designed software flexiblity as well as maximum hardware reliability. The master control unit (MCU) monitors shield support data as well as the plow/shearer position. By using an industry standard PC in an explosion-proof box with an intransically safe keyboard nearly unlimited software capabilities can be obtained with inexpensive hardware. Among various other modes of operation this MCU allows the monitoring and recording of data which can be transmitted to a surface computer. Production and operational adjustments can be made by the mine management based on the MCU information. Statistical analysis of the distribution of roof pressure under various conditions is also possible. The WESTFALIA automation system PM-4 gives the operator maximum flexibility and helps the mine management to run their longwall more efficiently and safely.

Jan 1, 1994