Search Documents

By B. J. Arnold

Utility coal specifications usually contain a requirement for a maximum moisture content in order to prevent coal handling problems and to minimize evaporative losses in the boiler. As most coal cleaning processes are water-based, dewatering and sometimes thermal drying steps are required to meet moisture specifications. Screens are often used for dewatering, with centrifuges and filters used to further reduce moisture in many cases. Algorithms to predict the performance of commercial dewatering devices were developed for the Coal Cleaning Simulator running under Aspen Plus? during a project sponsored by the U.S. Department of Energy and the Electric Power Research Institute. These algorithms include calculations for size degradation in the devices and fines loss to effluents, where appropriate, and a calculation for moisture content of the product based on particle size and specific gravity distribution. This paper discusses the algorithm for coarse and fine coal centrifuges and gives comparisons between predicted moisture and solids loss and published moisture and solids loss values for various particle size ranges.

Jan 1, 1996

By S. Tuylu, D. Adiguzel, A. Bascetin, O. Ozdemir, U. Cinar

"In recent years, use of mineral processing tailings as a paste backfill has been significantly increased due to the environmental problems occurred during the disposal of the tailings in mine area. The paste material used to fill the stopes excavated is generally consisted of tailings (solid ratio: 70–85%) and cement (3-7%w/w). Meanwhile, the strength of the paste material is completely related to ratios of these materials. Cemented Paste Backfill (CPB) system is used as support depending on the roof pressure and also as an underground disposal method. Therefore, temporary strength value of the paste material gains a great importance. For example, the paste backfill material must compensate the minimum 4 MPa strength value in order to procure the permanent fortification, and the mixture cost must be minimal as well. For this reason, in this study, the Pb-Zn tailings were used to prepare for the paste backfill material using cement in order to perform the uniaxial compressive strength (UCS) tests. Additionally, a statistical experimental design and linear programming techniques was used to find the optimum mixture in terms of strength and cost. The pulp solid ratios (PSR) of the tailings and cement (by the solid) were varied as 75-85% and 3-8%, respectively. The results of this study; the optimum mixture is ~79.5%PSR and 6.8% cement ratio (by the solid) for 4 MPa UCS (28 day) and 16-17 cm slump value determined by this method with statistically reviewed experimental data. INTRODUCTION Fine-grained tailing waste materials resulting from mining activities are an important environmental problem. In terms of environmental protection, the use of tailings with paste backfill is a very attractive approach and a desirable solution to tailings management. Paste backfill, which is used to fill underground openings, is made by primarly mine tailings mixed with hydraulic binders and water. Its main benefits are not only disposal of mine tailings in underground, but also providing a certain strength to ensure a safe working environment. Therefore, it is necessary to use hydraulic binders due to durability of the system (Benzaazoua et al., 2004). Paste backfill, formed from the mix of dewatered plant tailings (75-85 wt. % solids), water and binder (3-8 wt. %) (Brackebusch, 1994; Landriault et al., 2005).Water is used to determine the chemical reactions between tailing and binder materials for strength as well as increasing pumpability. Portland cement and ash can be used as binder materials (Douglas and Malhotra, 1987). The factors which affect strength and stability of paste backfill separate into two groups called interior and exterior factors. Interior and exterior factors determine the strength, stability and deformation features of backfill in short and long terms and also affect the transportation of backfill to underground (Benzaazoua et al., 2004; Erçikdi et al., 2006; Yilmaz et al., 2010; Nasir and Fall, 2010). Material properties of tailings as well as site operations to fill the underground openings are the most important steps for the design purposes. Grain size distribution, chemical, and physical properties of tailings, and mechanical properties of paste fill material are used to understand the suitability of tailings as paste fill material (Ozturk et al., 2014). In addition, Fig. 1. is also proposed to apply a typical design for the operational stages of paste fill applications on the site."

Jan 1, 2016

By B. J. Arnold

Coal froth flotation cells typically receive little attention in coal preparation plants. They process only a small portion of the total coal feed (perhaps 5-1 0% of the total plant feed in the United States), they are viewed as a way to take the load off the refuse thickener, and their operation is not well-understood by cleaning plant operators. Operating parameters are set based on the equipment supplier information, and reagent dosages are set at the recommendation of the latest chemical vendor. The cells then operate day in and day out, recovering coal and producing a product that may not meet ash or sulfur specifications or that may be the wrong percent solids for downstream dewatering operations. If improvements can be made to this circuit, then the whole plant will benefit. Paying attention to rate and residence time and the wealth of data from the literature or from a series of targeted laboratory tests can give operators the key to improving the performance of froth flotation cells AND overall plant performance. This paper provides an overview of froth flotation rate and residence time data and gives practical suggestions for specifying and using laboratory tests to improve froth flotation performance. Suggestions for improving froth cell performance are also given based on available literature data.

Jan 1, 1999

By B. J. Vorster

The South African Iron and Steel Company Ltd operates a large Iron Ore Mine in the Cape Province of the Republic of South Africa. The Mine is situated on the farm, Sishen, approximately 600 km west of Johannesburg. The annual capacity of the Mine is 100 million ton of ore and waste and the present production level is 60 million ton. The Mine operates continuously for 6 days a week. The primary equipment used to maintain the above production are 55, 154 t trucks (Wabco and Unit Rig) and 14 P & H shovels. During 1979 an urgent feasibility study into the application of a trolley assist system was launched at the Mine. This was due to the unrealistic escalation in the cost of diesel fuel and the appeal from the South African Government to reduce the use of fossil fuels. Tests and economic evaluations proved the system technical feasible. The estimated discounted cash flow return exceeded 50% and the diesel fuel consumption would be reduced by 120 million litres in the next 10 years. Management subsequently approved the implementation of the system at Sishen. The construction of 7,7 km of line and the conversion of 66, 154 t trucks were completed in March 1982.

Jan 1, 1985

By Norbert Patzelt, Hans Knecht, Wolfgang Baum

Future ore reserves of major gold producers in North America and elsewhere will consist of refractory gold ores. About 60 % of the current U.S. gold production is mined in Nevada. Several of the large gold operations in this state indicate that 40 to 90 % of their future ore feeds will contain refractory gold. To compound problems, average head grades for refractory U.S. gold ores have fallen from 8 - 9 g/mt to about 4 g/mt by 1991. In Latin America, 52 % of the gold operations will require milling for optimal recovery. Deeper reserves are, like in North America, refractory. Particularly in hard, (semi)refractory sulfide ores, many operations may experience substantial decreases of gold recov­ery. For example, Martins et al. (1991) report that at an Austra­lian mine, sulfide ore treatment led to 4 - 10 % lower gold reco­veries as the work index increased from 8 kWh/t to 14 kWh/t and the grind coarsened. Many refractory ores should actually be classified as semirefractory since a fine sulfide fracturing and liberation would make 80 - 90 % of the gold cyanide leachable. However, conventional comminution is often prohibitively expensive for these ore types.

Jan 1, 1995

By Stephen G. Tough, Ted M. Noskiewicz

INTRODUCTION For many years, in Europe and in North America, pre-formed metallic and concrete segmental linings in tunnels have been used extensively as temporary and permanent ground support systems. In the United Kingdom the use of cast iron as a means of ground support in mining shafts dates from the first decade of the 19th century. Although at that time wood tubbing was extensively employed, cast iron was used in shafts at Wallsend and Percy Main collieries in the North East of England. The original form of cast iron tubbing consisted of cylinders which were lowered bodily into the pit and were built from the bottom up, but subsequently they were subdivided into segments which involved the making of vertical as well as horizontal joints. Principally, the practice of providing immediate pre-formed support developed because of the incompetent state of the surrounding ground and, although this still remains the over-riding consideration nowadays, several other factors are examined before finally deciding what type of lining to use. Other branches of sub-terranean technology such as tunnel thrusting or immersed tubes (both of which involve pre-formed linings) can provide alternative solutions to problems hitherto thought better solved by bored tunnelling methods. However, this paper will confine itself to those linings developed for the more traditional tunnelling methods. Usually the shape of segmentally lined tunnels is circular because this profile is the most suitable for bad ground and many tunnelling machines. This does not always lead to the most economic use of space within the tunnel and horseshoe or elliptical linings are sometimes used in suitable ground. The number of segments

Jan 1, 1974

By J. B. Offei, K. Awuah-Offei

Mining companies registered with the SEC were required to comply with Regulation S-K 1300 for their annual report covering the first fiscal year ending on or after January 1, 2021. Consequently, most mining registrants filed their first S-K 1300 compliant disclosures in 2022. The US Securities & Exchange Commission (SEC), as part of its disclosure review program, has been issuing comment letters in response to these filings. This paper presents an overview of the trends in these comment letters. The authors reviewed comment letters retrieved from the SEC’s EDGAR database based on Standard Industrial Classification (SIC) Codes that cover mining, the content of the comment letter (whether it references S-K 1300 or not), the names of SEC staff listed in the comment letters, and other criteria. The analysis shows the SEC staff's reviews have been comprehensive covering the breadth of S-K 1300 and eliciting compliance with the rule. The staff through their comments are eliciting all the disclosures required by S-K 1300 and are not allowing registrants to substitute disclosures based on other standards for S-K 1300 disclosures. It is important, however, not to over generalize as the comments are based on the particular context.

Feb 1, 2023

By J. H. Bassarear, P. F. Thomas

Large-scale equipment can reduce both capital and operating costs for concentrators. Large semiautogemus (SAG) mills can be effectively utilized in big mills but they must be kept fully loaded to tab advantage of their great potential. With varying hardness ores, controlling throughput is difficult and careful design must take this into consideration. A variable speed drive on large primary semiautogemus mills can overcome this problem to a considerable degree. This paper provides a base case using standard accepted technology of two wound rotor single speed 4476 kW (6000 hp) motors to drive the primary SAG mills of a hypothetical 36,364 t/d (40,000 stpd) typical porphyry copper mill. One other fixed speed drive will be described and jive variable speed drive configurations will be reviewed. Capital costs for the entire grinding circuit, from crusher product to flotation feed, were developed for the base case and each of the alternatives. A technical evaluation comparing the advantages and disadvantages of each drive is presented.

Jan 1, 1987

NIOSH is conducting research to reduce the silica dust exposure of workers at surface coal mines. One goal of this research is to evaluate the relationship between drilling parameters, rock strata and silica dust generation. This study involved measuring blast hole emission dust from a rotary drill rig which required sampling high concentration dust (>400 mg/m3) for silica content in a high velocity airstream. To measure dust initially, traditional sampling methods using personal sampling instruments were attempted in and around the shroud area of the drill with no success. Variations in the dust cloud concentrations under the shroud, the condition of the shroud and its orientation over the hole, and ambient air conditions prevented consistent and accurate dust measurements from being obtained. Amore consistent dust cloud is necessary for accurate measurements. An area of the drill’s dust collector system that consistently draws the emitted airborne dust from the hole is the collector tube. This tube connects the drill collector’s vacuum and dust filtration system to the shroud area. Assuming the collector system is working as designed, sampling from the collector tube would enable more consistent and accurate samples to be taken. However, current personal samplers are unable to sample in the concentrations and velocities experienced in the collector tube, so another method had to be devised. To achieve the desired results, an in-stack cascade cyclone was used. Preliminary field testing shows positive results.

Jan 1, 2003

By D. Pappas

Over the past decade, the number of contractors working in underground coal mines has nearly doubled; however, the effect this has had on the industry's injury rates has been the subject of much speculation. The confusion exists because the U.S. Mine Safety and Health Administration (MSHA) database does not assign contractor hours to the individual mining operations where they worked. To better understand the safety record of the contractor segment of the industry, the National Institute for Occupational Safety and Health (NIOSH) undertook a comprehensive analysis of the data contained in the MSHA database. The first part of the study compared overall contractor and operator trends from 1983 to 2009 related to employment, hours worked and injury rate. One unexpected finding was that the larger contractors tended to have higher injury rates than the smaller ones. The second part of the study directly addressed the role of contractors on the safety record of 10 large underground coal mines. A detailed analysis provided both injuries and estimated contractor hours worked at these mines for the period 1992-2007. Comparison between the estimated contractor injury rates and the reported operator injury rates at these mines indicated that the contractor injury rates were significantly higher at most of the operations studied. However, the industry-wide data indicates that contractor and operator injury rates have converged since 2005 and are now equivalent. Mining Engineering, 2011, Vol. 63, No. 11, pp. 73-79. Official publication of the Society for Mining, Metallurgy and Exploration, Inc.

Jan 1, 2011

By Joseph Padgett

Of all the fossil fuels produced in the U. S., coal is by far the most abundant. U. S. reserves amount to an estimated 1.5 trillion tons, 2,500 times the 600 million tons produced in 1970. Although it would not be possible to recover all of this coal economically with current mining technology, a significant portion would be available given the proper circumstances. With existing technology, approximately one-eighth of these reserves is accessible, an amount which would last for several hundred years at the 1970 level of production. On the face of it, this substantial reserve should go a long way in meeting the Nation's energy needs. But coal offers special problems. As additional coal is mined and then burned, there are increased costs to the Nation's land, water, skies, and health. Hence, coal poses a dilemma because of its dual status as one of our most abundant domestic fuels and as one of our major sources of environmental degradation. Against the benefits that would be chalked up in the areas of national security, balance of trade, and economic well-being from the increased use of coal, we must enter on the debit side of the ledger the increased environmental cost. This paper reviews the use of U.S. fossil fuel, the drawbacks of coal as an energy source, the means being developed to overcome these drawbacks, and the background behind the present sulfur emission regulations relative to coal combustion. It also discusses in detail the Federal Environmental Protection Agency's (EPA's) current policies to ensure the continued use of coal as a major source of energy for fossil-fuel fired power plants.

Jan 1, 1973

By A. T. Yu

Two key components make up the core of a rapid excavation operation. They are: the breaking up of the rock and its removal. Owing to the complexity inherent in mechanical rock-breaking and the relative infancy of the art, for a number of years the first of these two components has received virtually undivided attention from the industry. Only recently has some concern been expressed about the technology and the economics of the much ignored second component: muck removal. As the continuous boring machine's percentage downtime continues to trend lower in the future, the need for adequate and more effective materials handling systems in rapid excavation will become increasingly more acute. (1) Recognition of the need for a broader and more far-sighted approach to our problem has been eloquently underscored in the conclusions of the Committee on Rapid Excavation sponsored by the National Research Council: "Ultimate attainment of the desired cost and speed improvements is significantly dependent on recognition of the excavation process as a system whose subsystems are critically inter-related. Substantial amounts of full-scale field testing of integrated driving, muck removal, and support subsystems are required." (2)

Jan 1, 1997

By P. James, L. J. Steiner, F. Turin

NIOSH researchers and an industry partner conducted an investigation to study the effectiveness of ergonomic interventions in mining. The study required a significant commitment of time and resources from the cooperating site, Bridger Coal Company. This paper focuses on some of the challenges faced by the researchers and their cooperator. Challenges included the need to redesign methods of identifying and prioritizing injuries, and the need to train the workforce in ergonomics while still maintaining progress and interest in the process. The authors discuss some practical interventions implemented by Bridger Coal to date, and discuss future research implications brought about by PacifiCorp’s Generation Business Unit, who monitored the project to determine whether an employee-owned ergonomic process could be implemented throughout their operations.

Jan 1, 2003

By Thomas J. Regan

The first stage of the Massachusetts Bay Transportation Authority's Red Line Extension Northwest, is a two-track rapid transit extension from Harvard Square in Cambridge, through three stations, to the Alewife Station/Garage complex in North Cambridge. The extension, about 5.0 km. (3.1 miles) in length, is entirely in tunnel, with the Alewife Station/Garage complex and adjacent line sections of tunnel constructed by cut-and-cover methods. The Station/Garage complex, just west of Alewife Brook Parkway, is in an area underlain by deep deposits of very soft highly sensitive clays. It is proposed to construct the station and adjacent tunnel sections by the slurry trench method, using the slurry wall as the permanent structural wall of the station and tunnel. The unusual nature of the underlying clay and its very high sensitivity raised questions concerning the feasibility of the proposed construction. Since research failed to reveal any construction precedent for the specific conditions encountered, a test section was undertaken to determine construction problems, resolve uncertainties, and to establish acceptable parameters for the construction of the slurry walls. PROJECT ORGANIZATION Sverdrup & Parcel as tunnel and transit systems consultant for the Red Line Extension-Davis Square to Alewife had overall responsibility for determining program objectives, project management and test implementation.

Jan 1, 1979

By A. Hoath, V. Paul, F. Haslam McKenzie

This paper considers mining ventures occurring in rural communities in Galicia, Spain and Western Australia, Australia. It compares and contrasts the communities where mining is taking precedence over other industries, examining the potential land use conflicts and the future of both the communities and the mines currently operating there. The Galician case study, Trevinca, is located 200 km inland and was once a primary producing area, notable for its scenic alpine landscapes, which have since been developed for small scale tourism purposes. The Australian case study, Boddington is located 100 km inland in what has been a highly productive farming area. Mining was a marginal industry in the case study areas but due to the comparative devaluing of agriculture and tourism and the increased value of mining outputs, mining has increased in scale and economic importance. This paper will consider the environmental, social and economic impacts that have occurred in both the case study localities. Where there have been land use conflicts, strategies for minimising the adverse outcomes will be considered.

Jan 1, 2011

By John W. Critchfield

This paper presents an overview of some of the basic issues related to tunnel construction in the presence of flammable and toxic strata gases. Gas properties and possible sources are outlined for the various gases that are commonly encountered underground. Assessment of potential gas hazards prior to construction is discussed. Measures for mitigating the problem during construction are summarized. This RETC Session on Gassy Ground has been organized by the Underground Technology Research Council (UTRC), Technical Committee on Gassy Tunnels.

Jan 1, 1985

By K. F. Jakob

Sustainable development is a principle for the way we should act in the present. It ensures also options for the future to achieve a balance between social, economic and ecology development. The efficiency of raw material utilisation is being enhanced through technological developments, starting from extraction through all the following stages of the value creation chain. The use of domestically produced resources helps to assure the technological know-how. Additional indicators being collected and published by individual companies are questionable in countries with a tightly regulated legal framework such as in Germany, but make sense in developing and threshold countries. Sustainability in terms of efficient use of raw materials will manifest itself at the next stages of the value creation chain. Examples for efficiency improvement can be found in the steel, the power generation and agriculture industries. The approval procedures for German mining operations entail an internationally extremely strict assessment of the potential impact on the environment. All the mining activities include remediation and recultivation where the practise in Germany has become model character by international levels.

Jan 1, 2005

By B. J. K. Sullivan, Brian Hornsby

INTRODUCTION Mount Isa Mines Ltd. operates a copper and silver- lead-zinc property at Mount Isa in northwest Queens- land, Australia. Mount Isa is located in the tropics at latitude 20°43'S and longitude 139°30’E (Fig. 1). It is on the upper watershed of the Leichhardt River and at an elevation of 365 m above sea level. The average rain- fall is 360 mm/y, the greater part of which falls in January to March (the hot summer months). The mean summer temperature for these months is 30°C (dry bulb), with a maximum temperature of 43°C; the mean wet bulb temperature is 25°C with a maximum of 28°C. Mount Isa is located geologically towards the western edge of the Precambrian Shield of northwestern Queensland. This complex forms a north-tilting dissected peneplain which extends in the north-south direction for 640 km, with widths varying from 32 km to 190 km. The combination of differential erosion, regional strike, and steep dips has produced a corrugated topography of low north-south orientated hills and valleys. The field was first discovered in 1923 as a silver- lead-zinc field. Mount Isa Mines Ltd. was formed the following year and subsequently became the sole operating company on the field. Lead and copper ore have been mined and treated separately and simultaneously at Mount Isa since 1953. Intensive exploration commenced in 1954 and an active exploration program provided the justification for a series of production expansion programs in both silver- lead-zinc and copper (see Table 1 ). The most recent and largest production expansion program at Mount Isa commenced when a decision was reached in December 1969 calling for an increase in copper production from 100 000 to 150 000 t/y of blister copper. A major factor which influenced this decision was the substantial additions to the ore reserves in the so-called 1100 ore body which is a massive copper sulfide ore body with a known strike length of approximately 2500 m, a height which is variable up to 300 m, and a width of generally 300 m up to a maximum of 370 m (see Figs. 2 and 3). Host to the copper mineralization is a complex and variable rock generally called "silica dolomite." The ore body strikes 6.02 to 6.1 rad (345° to 350°), dips west between 0.78 and 1.13 rad (45° and 65°), and is truncated at depth by fault implaced basement rocks. It first occurs some 600 m below the surface and bottoms at about 1000 m below the surface. The unconfined compressive strength of the silica dolomite ore varies from 150 to 250 MPa, whereas the basement rocks, carbonaceous mylonite, slaty shale, buck quartz, and greenstone (a chloritic schist) are considerably weaker, varying in strength from 20 to 80 MPa. The distribution of mineralization within the ore body is variable, but can be considered as generally high grade at or just above the basement contact and diminishing towards the upper reaches of the ore body. The current

Jan 1, 1982

By D. W. Wu, M. T. Haque

A novel impedance probe was commissioned specifically for capturing fast dynamic information about filtration processes. It provides an attractive alternative to more complex measurement techniques in situations where the slurry system is primarily one-dimensional. The probe can monitor mudline, slurry densification and drainage. Dynamic variations in cake permeability are obtained by combining dynamic mudline information obtained with the probe and filtrate rate data derived from a leaf test apparatus. The measurements are reviewed in relation to micro structural measurements obtained on iron ore filter cakes. The practical significance of these measurements for optimization of the filtration process is discussed.

Jan 1, 2002

By Martha McJunkin, Lawrence Pietrzak

This paper describes and demonstrates the application of systems analysis and mathematical modeling techniques in the planning of actual tunnel projects and research and development to improve tunneling techniques. A recently completed tunnel project located in Utah is used as an example. Although cost estimating computer programs are used in tunnel project planning, the introduction of performance modeling, simulating the time to excavate, has added advantages that are explored here. The performance/cost tunneling model (TM) described herein mathematically simulates on a high-speed digital computer the important activities of a number of tunneling techniques accounting for activity interactions, variable external environments, mechanical failure, and other uncertainties. A cost accounting segment is included to facilitate cost-effectiveness comparisons. It is shown that, when combined with informed judgment and appreciation of limitations, the TM can be a useful tool that may help improve tunneling operations and cost estimation, for example, by achieving more balanced system designs or bounding the performance/cost implications of geologic and other uncertainties. Ultimately, this might lead to more competitive bids and greater profits. The need for systems analysis and modeling in tunneling research and development (R&D) is well recognized and documented.(1-5) In R&D one must seek broadly useful solutions to the basic problems of face fragmentation, materials handling, ground support, and environmental control. These solutions must take account of the interdependence of these elements and, for a variety of ground conditions, the limitations or constraints that any innovation in one element may impose on total system performance and cost. In this regard the structure and logic of the TM has been kept as simple and modular as possible so

Jan 1, 1974