Search Documents

By Kadri Dağdelen, Matthew Deutsch, Thys Johnson

Nested pit analysis in open-pit long range mine planning is used to define approximate ultimate pit limits and an initial high-level schedule in the early stages of a project. Modern ultimate pit optimizers can solve for dozens, or even hundreds, of nested pits however often a smaller subset of pits which are evenly spaced with respect to contained tonnage are desired for downstream analysis. In situations where that pushback selection process must be automated, such as when performing sensitivity analysis, or when the best subset of pushbacks is required; an optimization procedure is warranted. This paper describes a dynamic programming algorithm for selecting pushbacks following nested pit analysis, which is performant and addresses a long-standing inconvenience faced by long range open-pit mine planners.

Jun 25, 2023

By S. Usui

In a previous article1 the methyl stretching vibrations for a series of xanthates and amines were reported, and the frequency of the methyl stretching vibrations in a homologous series of the alkyl compounds were shown to decrease exponentially with chain length and approach a limiting value corresponding to that of saturated hydrocarbon beyond six or seven carbons. These observations were explained quantitatively by the theory of Goto and Takenaka2 who proposed an equation relating the frequency shifts to the inductive effect of polar groups. As a result, the alkyl groups in the shorter chain heteropolar compounds were interpreted as becoming somewhat polar, and a good correlation was observed between the CH3-stretching frequencies and such surface chemistry parameters as contact angle, surface tension lowering, solubility, and critical micelle concentration" The substitution of fluorine atoms, the most electronegative of all atoms, for the hydrogen atoms in alkyl groups was expected to reverse the direction of the inductive effect within a heteropolar molecule, and its effect on the C-F stretching frequency shifts and on some surface chemical properties became of interest. In a recent study the C-F stretching frequencies of a series of normal perfluorocarboxylic acids and a few 1,1' -dihydroperfluoro alcohols were determined as a function of chain length and the results were compared with the corresponding hydrocarbon analogs. Furthermore, the nature of the induced polarity in the hydrocarbon and fluorocarbon groups was investigated through surface potential measurements at the interfaces of air-aqueous solutions of normal butyl alcohol and of l,l'-dihydroperfluorobutyl alcohol and through differential capacity and electrocapillary measurements at the interfaces of mercury-aqueous solutions containing the above two alcohols. Experimental Normal perfluorocarboxylic acids and 1,1' -dihydroperfluoro alcohols were provided through the courtesy of the 3M Company, St. Paul, Minnesota. Normal butyl alcohol was purchased from Distillation Product Industries, Rochester, New York. A Perkin-Elmer Model 621 infrared spectrophotometer was used to investigate the spectra in the frequency region of 1200 to 1270 cm-l with frequency scale

Jan 1, 1971

By James McManus

The Lornex mine is located on the Southern slope of the Highland Valley in South Central British Columbia. The large low grade deposit was discovered in 1964; stripping began in 1970, and the mill started commercial production in October of 1972. The orebody is classified as a complex porphyry type having as major constituent quartz diorite, with varying amounts of quartz, grano diorite, and porphyry. A substantial degree of alteration is evident in the host rock, and this became the key factor in major equipment selection for the grinding section. A pilot plant was constructed on the property capable of treating 100 TPD of ore. The ore was mined to be as representative as possible of the entire orebody by sinking a shaft and cross cutting the deposit underground.

Jan 1, 1975

By G. S. Dobby

Particle collection is considered to occur by particle collision with the bubble followed by the particle sliding over the bubble during which attachment may occur. Collision is quantified by a collision efficiency, EC. The existing model for EC is extended by including particle inertia. Attachment is quantified by an attachment efficiency, EA calculated as the fraction of particles which reside on the bubble for a time greater than the induction time. These calculations use recent data on the liquid velocity distribution over the upper half of rigid spheres. Collection efficiency, EK is given by EK = EC ? EA. Detachment is not considered. The mode is examined and shown to agree with much experimental data. For example the maximum observed in recovery vs particle size (d) can be explained as E increases with increasing d , while EA decreases. The decrease in selectivity at fine sizes is in accord with the model result that for dp < 5µm, EA ? 100% (i.e. EK ? EC) almost regardless of induction time. A decrease in bubble size does increase EK but does not improve selectivity. A high particle density (> 5g/cm3) is shown to cause a sharp peak in recovery vs size and a decreased maximum size of floatability. Finally, the possible effects of bubble and particle concentration are explored.

Jan 1, 1985

By M. C. Williams

The solution of the dynamic population balance model (PBM) of a closed grinding network consisting of a mill, sump, and cyclone is problematic. The fact that the dynamic PBM model equation solution to the Inverse Problem for grinding systems is degenerate or underspecified is demonstrated. Two numerical solution approaches to the Inverse Problem are used. These are: 1) providing additional constraints on breakage selection functions or 2) performing the Arbiter-Bhrany (or other) normalization of the selection functions. Actual experimental anthracite batch grinding data is used to demonstrate the non-unique functionality of the batch dynamic mill selection and breakage functions for a real physical system. The Levenberg-Marquardt algorithm for systems of constrained non-linear equations is used to solve the batch dynamic PBM grinding equations to obtain the grinding selection and breakage rate functions. Different solutions to the same PBM transport equations are provided. The mill, sump and hydrocyclone were modeled as a CSTR operating at various retention times. Batch dynamic PBM data was used to provide the mill kinetic and breakage selection function data. Two different solutions were obtained depending on the numerical solution approach. The severity of the non-uniqueness problem for dynamic grinding is demonstrated. Each solution approach to a dynamic PBM with transport, while giving the same prediction for a single batch grinding time, gives different solutions or predictions for mill composition for other grinding times. This fact makes dynamic nodal analysis and control problematic. The fact that the constraint solution approach gives a solution may suggest that normalization for closed networks is not necessary. Differences in solutions to the PBM cannot be excused away by inaccuracies in the data used to model the grinding phenomenon.

Jan 1, 1995

By John W. Brauns

18.1-RAILROAD JOHN W. BRAUNS Conventional railroad haulage can be employed at both open-pit or strip and underground mines-in the latter case, largely for transfer of ore from distant openings to processing plants, or processed material to loading points or docks, using standard hopper cars for bottom unloading or gondolas for rotary dumping. The major application, however, is in surface mining for moving ore and/or waste out of the pit to a crushing plant or dump. Consequently, the following will deal largely with this phase of railroad operation, though the conclusions apply equally, for the most part, to other rail-type surface haulage. In surface mining, trains consisting of a locomotive and gondola or side-dump cars suitable for loading by power shovels are used. Gondolas are restricted to hauling ore as a rotary dumper is required. Side-dump cars are more versatile, carrying both ore and waste, but because of their additional dumping mechanism they are likely to be more expensive to maintain.&apos; Also they weigh up to twice a flat-bottom car of the same capacity and. therefore, fewer" cars can be hauled per train. Standard-gage track is most commonly used. Track systems incorporate low-quality temporary track where moves are frequent and permanent high-quality track on main lines. Rail haulage can be used alone, or in combination with other surface haulage methods, thus permitting a selection best adapted to the peculiar requirements of each mining project. 18.1.1---GENERAL APPLICABILITY, CONTROLLING PHYSICAL CONDITIONS For handling rough rock, the shovel-train system is unexcelled.&apos; The ideal applica¬tion is in a large, but not excessively deep, open pit mine from which the coarsely blasted ore and waste must be transported over 3 mi. If. in addition, a high production rate is to he maintained, railroad haulage probably will afford a lower cost per ton transported. Grade must he relatively gentle-usually 3% uphill and 4% downhill. The greater the differences in elevation involved, the greater are the track grade space requirements; for example, a 3 c ramp out of a pit only 300 ft deep is almost 2 mi long. Main-line track locations should he selected carefully so that the number of moves during the life of the mining operation can he kept to a minimum. This applies both to the ore haulageway and that for waste. Such moves are not only expensive, but are difficult to execute without adversely affecting production rates. The large mine affords greater opportunities for judicious location of semipermanent trackage. Figs. 18-1 and 18-2 illustrate typical track layouts. The effect of terrain in considering railroad haulage is confined chiefly to the initial cost of the installation. Grade construction in mountainous territory is ap¬preciably more expensive. However, if that expense can be borne, the subsequent maintenance cost of trackage will not he much higher than in areas of low relief.

Jan 1, 1973

By Nathaniel Arbiter, Robert R. Beebe

The U.S. mining industry - once world dominant and largely independent of foreign sources for most major commodities - has today lost this position, with little likelihood of regaining it. But even though Business foretold The Death of Mining four years ago, the current outlook is less pessimistic because of drastic restructuring of the industry; a major reduction in its labor force, with resulting large increases in productivity; and introduction of improved technology. In the face of this clearly changed climate for domestic mining, it is important to examine the role of the development and research establishment in the industry&apos;s future, which raises a complex set of questions: 1. Where and to what extent can new technology assist in the continued survival of the industry ? 2. What is the past record of the research establishment in developing new technology; and what is the industry&apos;s record in supporting and adopting it ? 3. In the light of these records, and of the drastic cuts in both research staffs and expenditures, what areas should be the most important targets for new technology? New Technology vs. Old A1 though mineral processing&apos;s origins can be traced back through five or six millennia, its modern structure is about 200 years old.

Jan 1, 1989

By John A. Folinsbee

Placer Dome Canada owns and operates the Campbell mine and mill at Balmertown, in the north western corner of Ontario. The mine operates at 1.3 kt/d (1,500 stpd). It produced more than 9.3 t/a (300,000 oz/year) of gold during the last three years. Changes to the gravity concentration circuit have resulted in a 10% to 15% increase in gravity recovery. The mill head grade at the Campbell Mill is relatively high, averaging 18.5 g/t (0.54 oz/st) over the total reserve tonnage. During the past several years, the head grade was averaging close to 20 g/t (0.6 oz/st). Before 1994, gravity concentration was achieved by using a combination of conventional mineral jigs and tables. Jig concentrates were upgraded on shaking tables to produce a concentrate, which was refined to bullion. In May 1994, management decided to buy two Knelson CD 760-mm (30-in.) concentrators. The objective was to replace the existing jigs and increase gravity gold recovery by up to 15%. Gravity recovery with jigs averaged between 30% to 35%. Gravity recovery was anticipated to increase to about 50% with the Knelsons.

Jan 1, 1997

By M. M. Fine

One of the most persistent topics at technical gatherings and in the recent scientific press has been the reduction of iron ore. To cite some of them, in May 1960, a symposium on the subject was sponsored by the Electrochemical Society. The proceedings, comprising two dozen papers, were later published.3/ More recently, November 1966, a similar gathering took place at Michigan Technological University, Houghton, Mich. The latest meeting was the International Congress on Production and Utilization of Reduced Materials, Evian, France, May 1967. If the volume of literature, symposia and conferences is a measure of industry concern, then current interest must be at a high level. To the casual observer of the metallurgical scene, the abiding and recurring attention to iron ore reduction outside the blast furnace must be somewhat puzzling in that so much research endeavor has resulted in so little commercial activity.

Jan 1, 1968

THE FUTUREGEN CLEAN Coal project will be the recipient of $1 billion worth of federal stimulus money by way of the U.S. Department of Energy (DOE), which announced the commitment to the project. The money is expected to kick off years of further work that could finally see the project completed. One of the companies involved, Ameren Corp., said the $1.2 billion project ? which will include some private funding ? still has a number of hurdles to clear.

Jan 1, 2010

By E. Martinez

A heavy mineral sand sample was tested containing 13% heavy mineral consisting of rutile, zircon, and ilmenite. Eleven tests were run at a mill site with a Mineral Deposit Limited MG 4 spiral to determine the effect of the addition 0; magnets to the spiral compared to conventional gravity separation. Different magnet configurations and field strengths were tested. Optimum results were obtained with the spiral retrofitted with magnets. The heavy mineral content of the concentrate was increased from 55.5% in the control to 64.2% with the magnets. The 8.7% improvement in heavy mineral recovery was due not only to the weakly-magnetic ilmenite, but also to increased recoveries if the non-magnetic zircon and rutile. The increased recoveries were achieved with no loss of concentrate grade.

Jan 1, 1992

By Hung-Kei H. Lam

Rubidium and cesium were discovered by Bunsen and Kirchhoff about 100 years ago. These two elements are by no means as abundant as sodium or potassium. Their occurrence in minerals is widespread, but usually as minor constituents. There is no known specific ore containing rubidium, but rubidium is found replacing the. other alkali metals in .some minerals.. Perhaps the highest concentration of rubidium found in one mineral is in lepidolite, KLi(OH,F)2A12Si3010, which contains from 0 to 3.5%*Rb20. 0n the average, lepidolite contains about 0.5% Rb20. Other sources of rubidium are carnallite, KMgCl3?6H20; pollucite, H20.2Cs20.2AI203.9SiO2; rhodizite, R20.2A1203-3B203; biotite, H2K(Mg,Fe)3A1(Si04)3; sea water, rivers, marine and fresh water organisms, soils, and plants. Cesium, even though it is the least abundant. of the stable alkalies, has a specific ore. Pollucites a hydrous cesium aluminum silicate, may con¬tain as high as 42.5% Cs20, although again, the average Cs20 content is about 25% among the handful of known deposits. Other cesium-containing minerals are lepidolite and carnallite. Rubidium and cesium are very much like potassium in chemical properties, consequently, they are hard to separate. Because of the difficulty in obtaining pure cesium and rubidium compounds coupled with the scarcity-of supply, prices were high and the two elements enjoyed little industrial use. Just before the Second World War, the world. supply of rubidium and cesium, from Germany, was a matter of tens of kilograms per year and prices were about

Jan 1, 1959

By N-h. Mao

We applied kriging (geostatistics) to interpret the structure of basement rock in Yucca Flat, NTS from borehole data. The estimation error for 118 data is 81 m comparable with those based on both gravity and borehole data. Using digitized topographic data, we tested the kriging results and found that the model validation process (Thomas option) on data gave a fair representation of the overall uncertainty of the kriged values.

Jan 1, 1985

By C. O. Petter

This paper, in its first part, compares the profile and economic weight in the extraction of industrial minerals and aggregates to the so called conventional mining activities (metals, coal, gas and oil extraction) in Brazil. In its second part, a descriptive analysis of the present situation of the education in Brazil is made, emphasizing the graduation and post-graduation formation especially in engineering. The curricular structure of the schools that prepare the mining workforce is discussed and the presence of specific subjects in industrial minerals is evaluated. Finally, considerations are made on the actions being taken in the main universities and companies, aiming to improve the formation of the specialized workforce. The Brazilian mining production, comparing 2010 to 2011 showed an expansion of more than 3% (IBGE, 2012). Not bad, but nothing to do with the 13% growth between 2010 and 2009 (influenced by a recovery effect from the 2008 commodities? nightmare). The commodities that had a rising behavior were titanium, gypsum, nickel, graphite, bauxite, phosphate, chrome and chrysotile. All of them were eclipsed by the impressive growth of iron ore production. Some decreases could be noticed, eg. in zinc, kaolin, magnesite and salt production (DNPM, 2012). In fact, the mining activities followed the positive growth of the country these last 5 years. The commercial balance (exports against imports) was not spectacular (positive in US$ 30 billion in 2010). It is important to notice that the mineral commodities balance was US$ 35 billion, representing 27.4% of the total exports and 15.6% of the total imports of Brazil (DNPM, 2012). In this positive environment, the workforce in Brazil showed progress in number of formal jobs and average revenues.

Feb 23, 2014

By Bruce A. Kuyper

Routine core drilling at the Cove deposit failed to confirm gold-silver grades and length of intercepts observed in reverse circulation drilling. A drilling program was designed to ascertain whether the disparity was due to problems with reverse circulation drilling techniques, core drilling techniques, or the erratic nature of the gold-silver mineralization. Special sampling devices and core drilling methods were employed. Data obtained from core-reverse circulation twins showed that down-hole contamination during reverse circulation drilling accounted for much of the variation between reverse circulation and core drill results. Down-hole contamination occurred as a result of high ground-water inflows eroding friable vein material from hole walls.

Jan 1, 1991

By Elmer H. Citron

The Monterey Coal Company, a wholly owned subsidiary of The Carter Oil Company of Houston, Texas, recently awarded a contract to build the Monterey No. 1 Preparation Plant, which will be located near Carlinville, Illinois, to the McNally Pittsburg Manufacturing Corporation. The preparation plant will be one of the most modern jig preparation plants in the State of Illinois. Illinois No. 6 coal will be delivered by a 48" slope belt having 35-degree carrying idlers, operating at 650 FPM and operating on an incline of nearly 17 degrees. The slope belt is driven by two 450 BP motors and will deliver the mined coal at the rate of 1800 TPH to a stationary step-type &apos; screen having six-inch openings. The overproduct from the stationary screen will discharge into a 10&apos; x 24&apos; McNally Rotary Breaker and the underproduct will bypass the rotary breaker. The rotary breaker is equipped with heavy manganese screens with 6 ½" diameter openings. The sized 6" x 0 coal from the stationary step screen and the rotary breaker will be discharged by gravity to a 4%" raw coal incline storage belt. The 48" raw coal storage belt will deliver the 6" x 0 sized coal at the rate of 1800 T?H to an 8000 ton concrete raw coal silo, 70 feet in diameter and 1x7 feet high. The 6" x 0 sized coal will be drawn from the concrete storage silo by seven (7) 36" wide reciprocating plate feeders. Five feeders are to have constant speed drives at a rated capacity of 145 TPH each. Two (2) feeders will have remote con- trolled variable speed drives, to provide a varying feed.

Jan 1, 1970

By Dan Nilsson

Rock from underground mining has a size-distribution, that varies from mine to mine, depends on rock conditions and mining method and on how much explosives etc, that is used. Because at the high costs, associated with full-scale studies of the size-distribution of blasted rock in a mine, detailed information is seldom published about such size-distributions. However, some facts can be noticed. Rock from tunnelling and other types of development work has a fine fragmentation. Cut-and- fill mining is a method that normally results in blasted rock with an advantageous size distribution. Block caving on the other hand often results in large amounts of boulders, since blasting of the rock is normally not used.

Jan 1, 1985

By E. Woodburn, H. W. Smith, M. C. Fuerstenau, R. Putman

This paper presents a review of developments to date in computer control practice, based in large part on Canadian experience. The basic problem examined is that of stabilizing control; matters considered are control strategies, hardware and software aspects of system implementation, reliability, human factors, and economic results.

Jan 1, 1976

By Li. S. D., R. X. Zhang, K. M. Li, Y. D. Zhang, Y. J. Hou, S. G. Li

A computer aided design software system for long range coal surface mine planning has been developed by the authors. The system is composed of two subsystems: a coal deposite sub- system and a long range mine planning system. The geological parameters are estimated and a grid model is formed, then a 3-D block model can be developed for mining design. The long range surface mine planning system is based on oriented graph simulation and combined approaches to seek for the optimal deign alternative. This mining model consists of a number of sub-models to realize mining design functions such as: calculation of mining volume and coal quality by graph scanning; determination of operational stripping ratio by interactive design; varification of annual coal production; delimitation and development of dumping site; optimization of material flow direction and volumes by Linear Programming; surface mine production scheduling by interactive iteration; etc. The software package was developed on PC computer 486. It features classified menu guide, module structure, figure and graph representation on the screen and flexible interactive functions. This system has been applied to an open cut coal mine and predicted functions have been obtained.

Jan 1, 1996

By Kanaan Hanna, Mir Heydari, Dipack Sengupta, Gordon B. French

This article, first in two, discusses the safety, technology, and economic impact of eliminating safety fuse from metal and nonmetal mines. It is based on operation and manufacturer experience over the past five to 10 years. If safety fuse is eliminated, blasting accidents will decrease. There should be only limited technical impact. The economic impact will be minor for large operations, but will be significant enough for small operations that some will likely close rather than change. Most mines would probably change over, with the market absorbing the extra cost. Elimination of safety fuse would obviously have an impact on the two safety fuse manufacturers. One manufacturer produces an alternative system and would be unaffected. The other, however, will be affected if it does not change its production strategy. From the standpoint of employment and production, abolishing safety fuse will have a very minor effect on the mining industry as a whole. This article discusses the current use of initiation systems, incidence of accidents, and fuse consumption. Next month, part two describes the economic impact of eliminating safety fuse on the mining industry and manufacturers, and presents an economic analysis of the initiation systems. Introduction The objective of this study was to determine the safety, technology, and economics of eliminating safety fuse from metal and non-metal mines. There were five major tasks: • Studying initiation-related accidents from the Health and Safety Accident Center (HSAC) data file; • Visiting mines, collecting relevant data, and interviewing mine operators; • Establishing the trend in safety fuse consumption and type of users; • Corresponding with fuse manufacturers, domestic and foreign; and • Developing an idealized blasting cycle to evaluate the possible economic impact of safety fuse elimination on large and small operations. More than 450 explosives-related accident reports have been screened and analyzed by investigating HSAC files. These reports have been studied and classified according to the four initiation systems, size and type of mines, and time and frequency of accidents from 1973 through 1978. Twenty-four mining operations were visited to obtain supporting data for this study. Mine personnel were interviewed to determine attitudes about safety fuse and alternative detonating systems. This article decribes available data. It also attempts to provide information that can be used to answer such questions as: • Is the use of safety fuse (an antiquated detonation system) a major cause of mining accidents? • Are alternative systems available that could result in fewer in-juries to miners?

Jan 1, 1984