Search Documents

By Stephen H. Stow

Economically important heavy minerals have been studied in the sediments of offshore Alabama and Mississippi. Sandy samples have been collected from a 200 square mile area from Dauphin to Horn Islands. The minerals concentrate in sediments under 10-35 feet of water and may reach 2.4% by weight. The distribution of total heavies is related to the hydrodynamics of offshore Alabama-Mississippi; the greatest concentrations are in the Gulf where the longshore current is diverted from its westerly flow. Preliminary observations indicate that the distribution of individual minerals can be correlated with wave energy, particle size, specific gravity, and morphology of the mineral grains. The coarser, lighter minerals--kyanite, sillimanite and staurolite--are concentrated in relatively low energy areas in the Mississippi Sound and at the end of Dauphin Island in the Gulf; maximum concentration for each is 34.5%, 6.0% and 43.2%, respectively, of the heavy minerals. The smaller, more denseminerals--ilmenite, rutile, leucoxene, zircon and monazite--are concentrated in high energy areas in the Gulf; maximum concentration for each, respectively, is 42.0%, 5.9%, 9.652, 10.7% and 1.3% of the heavy minerals. On the basis of a minimum concentration of 1% heavy minerals, two areas have been identified and the total amounts of different minerals have been calculated to a depth of 25 feet of sediment. The data are preliminary and in no way indicate recoverable reserves, but they do show that on the order of 20 million tons of heavies exist. These deposits should be termed "indicated resources".

Jan 1, 1975

By Behzad Khorshidi

"The ultimate objectives of the post-tensioned strands are to connect the precast segments into a ring and provide pre-stress in the tunnel circumference. The method involves inserting the strand through the preliminary embedded duct in the precast concrete segments and then tensioning the strand by jack and fastening it. The post-tensioned strand eliminates the necessity of bolt connections between the segments and may reduce the labor cost and increase speed of lining construction. Pre-stressing of the segmental lining reduces the steel reinforcement or fiber volume in precast segments and/or thickness of the precast segments which would result in reducing the manufacturing cost of them. Pre-stressing would reduce cracking and increase water tightness, and would provide smooth intrados due to eliminated bolt joints and pockets in the tunnel lining. Pre-stressing would increase resistance to internal pressures as well. Further, this system could work very well structurally in tunnels with squeezing rock or tunnels with high seismic loadings. INTRODUCTION OF THE METHODPost-tensioning is commonly used in the construction of bridges, large buildings, nuclear power stations, and water tanks but its utilization in tunnels is still in its infancy.The precast pre-stressed concrete segmental lining can be used for shield tunnels. It provides a reinforced lining ring by the following construction stages and as shown in Figure 1:1) Segments to be assembled by TBM to complete a full ring2) Steel strand to be inserted through embedded duct (sheath) within the segments3) The strand to be tensioned by Jack after anchorage of the other end4) The strand to be fastened after reaching required tension load5) The horizontal strands (if necessary) to be installed, tensioned and fastened6) The recesses and gap between strand and duct to be filled by groutingFurther, Figure 2 shows an unbonded post-tensioning strand model; Figure 3 shows an anchor sample (Xanchor); Figure 4 shows a duct (sheath) and anchor within reinforcement; Figure 5 depicts the posttensioning of a strand by jack; and Figure 6 is an image of the Midorigaoka Trunk line tunnel in Sagamihara, Japan which was constructed using this system."

Jan 1, 2016

By Turan Uysal, Ramazan Aydogmus, MURAT ERDEMOGLU

The paper investigates the effects of calcination for thermal activation and intensive milling for mechanical activation on aluminum recovery by acid leaching of pyrophyllite ore enriched via attrition scrubbing and froth flotation. The study compares these methods in terms of energy consumption and aluminum recovery, concluding that mechanical activation is more economical and environmentally friendly.

Nov 1, 2023

By J. R. Batista

Leachates from gold heap-leaching mines contain selenium concentrations as high as 2 mg/L. Previous studies report satisfactory selenium adsorption by activated alumina when using relatively "clean" drinking waters. However, the findings of these studies cannot be directly applied to the treatment of mine leachate where other ions compete for the alumina adsorption sites. This study evaluated the adsorption of selenium from a mine leachate to develop design parameters for full-scale activated alumina processes. The study revealed that 68% of the selenium in the leachate could be removed by alumina at pH > 5.0. Silica adversely affected the selenium adsorption capacity. At pH values < 4, silica was poorly adsorbed by alumina and selenium adsorption was improved.

Jan 1, 1994

By David B. Brooks

I gratefully acknowledge the help of a number of American and Canadian geologists, in both federal surveys and in private firms, who took the time to discuss this problem with me. Hans Landsberg and Bruce Netschert also followed the study with interest and encouragement. In their 1961 monograph, THE FUTURE SUPPLY OF THE MAJOR METALS, Bruce Netschert and Hans Landsberg noted that identified potential resources (that is, known but submarginal resources) of lead and zinc were much lower relative to reserves (that is, known and supermarginal resources) than was the same ratio for other metals.1/ Put another way, it seemed that for such metals as iron, manganese, copper, and aluminum, slightly more favorable economic conditions or modest advances in technology would greatly increase reserves by permitting the exploitation of vest quantities of leaner or deeper or otherwise less valuable mineral deposits. But for lead and zinc, Netschert and Landsberg concluded that either: "(1) there is relatively little material below present cutoff grades; [or] (2) such material exists, but for some reason there are no data.? 2/ This situation, which they called "the lead-zinc anomaly" has been subsequently discussed by other authors. The purpose of this paper is to carry the discussion further by examining the evidence in favor of (1) and (2) and by advancing a third alternative.

Jan 1, 1967

By R. J. Roman

The "mass balance" is unquestionably the most common class of problems for the process engineer&apos;. Closely related, mathematically, is the "heat balance". Every laboratory test requires a mass balance to describe the results. Mass balance calculations can be subdivided into several sub-categories based on whether the results are time dependant or not and depending on whether the input data are measurements that contain errors or are hypothetical values with no errors. Time dependent mass balances are dynamic process simulations and in addition to the conservation of mass constraints require kinetic data input. They are one step beyond simple mass balances.

Jan 1, 1992

By Manuel Gomez

This, report presents correlative data on ash and sulfur forms for Pittsburgh seam coal from Greene County, Pa. Prediction equations were developed for sulfur form distributions and washability characteristics. The equations developed were evaluated with an independent set of exploration core samples. It was demonstrated-that both sulfur distributions and washability characteristic&apos;s can be predicted from exploration core data ahead of mining. This information can improve the efficiency of selective mining techniques for the production of a uniform metallurgical coal product.

Jan 1, 1967

By CASSANDRA L. HOEBBEL, Emily J. Haas, MARGARET E. RYAN

Researchers examined datasets from two separate studies that measured common demographic variables but different safety performance outcome variables. Of specific interest was how types of experience might relate to workers’ preparedness to effectively mitigate or respond to both routine and nonroutine risk in the mining industry. The results suggest that individual factors such as length of job, industry, and mine experience are predictive of routine safety performance — as measured by self-reported proactive and compliant safety behaviors — and/or nonroutine safety performance — as measured by perceived competence in self-escape knowledge, skills and abilities (KSAs) — in significant and sometimes unexpected ways.

By E. M. Frizzell

This paper addresses the use of the microcomputer programs BACKONE and BACKWEDG for an estimation of rock mass strength characteristics by back analysis of plane and wedge failures. The artificial support requirements are also determined by the programs PLANE2, BOLTPAT, and BOLTWEDG in terms of rock anchor installation angles, tensions, and installation patterns. These programs have been combined into a package called BACKPACK, which can be applied in open pit mines where some failures have already occurred.

Jan 1, 1988

By Richard C. Mayberry

Phosphate reserves have been and still are a controversial subject. Some published estimates are particularly conservative and have caused concern in government and political circles that southeastern phosphates are a dwindling resource. "Ores and ore bodies" are a function of economics that relate to a time/demand factor. The history of phosphates and other mineral commodities is one of mineral deposits (resources) ever becoming ore (reserves) via a long term logic based on price, supply, and demand factors operating through time and improved technology. Projections indicate that southeastern phosphates are sufficient for several centuries of operations at present production rates.

Jan 1, 1981

By Miche1 Dagbert

In most open pit operations mining porphyry type deposits, production planning rests on an are reserve inventory block file which is derived from diamond drill hole data. With such a practice, the way by which block values are generated is critical and in the recent years many studies deal with the comparison of different estimation methods for block grades (Mueller, E. (1), Knudsen et al (2) (3), Barnes, (4), Williamson and Mueller (5). Typically in such studies, one selects a bench or a group of benches where there is a "sufficient" number of blast holes (BH) with assay values in each of the blocks (generally 30.5 x 30.5 m (100 x 100 ft) or 15.2 x15.2 m (50 x50 ft). Then the arithmetic mean of the BH values in each block is computed and it is assumed to represent the real block grade against which different estimated values are compared. However it is sometimes observed that the variation of these BH values within a block is high and that their arithmetic average may significantly differ from the real average grade of the block (Barnes (4). The problem of the precision of the mean BH grade in a block has been examined by Williamson and Langlois (6) in an experimental way. They strove to find a better estimate of the average block grade than the mean BH grade but their results were not conclusive. The purpose of this study is to investigate the same problem within the frame of geostatistical models (David (7). Besides practical results obtained with these models, two general points are emphasized and illustrated in the text. First, "good results" are obtained if "good geostatistics" is done (David et al (8).

Jan 1, 1978

By E. Kurt

The field of percussion rock drilling is subdivided into two areas of application; that which takes place on the surface and that which takes place underground. Surface drills are used in quarrying, highway construction, and maintenance work; underground equipment in mining and tunneling work. Two basic principles are involved in the operation of all percussion drills. First, the principle that reciprocates the impacting piston and second, the principle that causes the drill steel and bit to rotate. The back and forth motion of the piston is accomplished by a self-acting automatic valve that admits air alternately to each end of the piston (Figure 1). Drill steel and bit rotation is imparted by an integral ratchet mechanism (Figure 2) in the so-called "rifle bar" machines (Figure 1) or by a separate pneumatic motor in "independent rotation" drills (Figure 3). While rock drills are subject to all kinds of physical and operational abuse, they are most sensitive to faulty lubrication. Proper lubrication is the single most important factor in the longevity of a percussion drill.

Jan 1, 1970

By J. L. Post

A large body of readily available Na-montmorillonite is present about 24km (15 miles) east of Fallon, Nevada. The clay is comparable to Wyoming Na-bentonite, but with somewhat less MgO and somewhat more Fe2O3 in its crystal structure. The physical and industrial properties of the Nevada clay are comparable to those of the Wyoming clay. The Na-montmorillonite is presently mined for use as hazardous waste barrier material and as a sealant for canals. It may be economically feasible to process the clay material for removal of impurities.

Jan 1, 1996

By C. H. Grant

The Dew Chemical Company has been engaged in explosives research since 1953. The incentive for this research was based on the desire to find additional markets and uses for magnesium metal of which Dow is a heavy producer. The thermodynamic calculations for explosives incorporating light metals indicate energies approximately twice that of non-metallized explosives currently being used. Early in 1960, we acquired additional patent rights from independent inventors and decided to set up a development station at Virginia, Minnesota, to conduct a commercial testing and market evaluation program with this new product. The actual manufacturing of the explosive was to take place in the bore holes. Due to the complexities involved in controlling the manufacture of the explosive in the bore hole, performance was sometimes in doubt. Furthermore, our experience indicated that the metallized explosive systems could not be evaluated by the standard laboratory methods then being used, and it was necessary for us to look for more suitable research methods. Tests were conducted on several known methods for explosive evaluation. The most promising were the Navy underwater method for energy evaluation, and a modified Livingston crater method intended to compare explosive performance in rock. After shooting over two thousand charges of eight to 60 pounds under water and in taconites and granites with many types of explosives, we have developed a metallized explosive which is now being manufactured at a pilot plant in Virginia, Minnesota, and is being evaluated commercially.

Jan 1, 1963

By S. A. McGhee

ASARCO Incorporated embarked on a modernization and expansion program to improve overall operating efficiencies and to more effectively develop the large mineral reserve at the Ray Complex Open-Pit Mining operation located near Kearny, Arizona. Major elements of this Ray Modernization and Concentrator Expansion Project included engineering and construction of a 54,400 MTPD (60,000 STPD) In-Pit Crusher and Overland Conveying System. and a 24,200 MTPD (30,000 STPD) Copper SAG Concentrator and Tailings Disposal System. Detailed engineering, procurement, and construction management were initiated in November 1989 under contract with Bechtel Corporation. Field construction commenced in May 1990 leading to mechanical completion and start-up during February 1992.

Jan 1, 1993

By E. Rubenstein, V. Gangrade, K. V. Raj, M. L. Harris

Underground stone mine ventilation is characterized by large openings with low resistances. These mines primarily face three challenges: moving adequate volumes of air, controlling and directing the airflow, and planning ventilation systems that work well with production requirements. Given these challenges, this paper examines the data collected by the Mine Safety and Health Administration (MSHA) to determine the extent to which respirable crystalline silica (RCS) and diesel particulate matter (DPM) are an issue in underground stone mines. Out of 522 sampled mines, there were 108 personal samples exceeding the RCS Permissible Exposure Limit (PEL) during 2000–2020. DPM were more prevalent than RCS in these mines with 382 personal samples exceeding the DPM PEL out of the 929 mines sampled during 2002–2020. Dilution of DPM is usually the defining parameter for design of mine ventilation systems in largeopening underground stone mines. With this knowledge, focused attention can be directed to these mines so that appropriate prevention and mitigation techniques can be utilized to prevent stone miners’ exposure to RCS and DPM and subsequent respiratory diseases.

Mar 2, 2022

By Joseph W. Leonard

Much progress has been made in the application of geostatistics to hard rock ore deposits.1,2,3 4,8 Progress in the application of geostatistics to coal deposits has developed over a period of time out of hard rock technology.5,7 Exploratory drilling in many hard rock deposits is frequently significantly more productive than exploratory drilling in coal deposits. For example, hundreds of feet of drilling and/or many drill setups are frequently necessary to obtain a few samples from a typical 4 to 6 foot thick coal seam. With hard rock deposits, which are frequently thick or volumetric, less drilling dead work is involved in sampling the deposit. To produce a variogram, which is the basic element needed for geostatistical analysis, a few well positioned holes drilled into a hard rock deposit where the core(s) can be divided into many sections can produce a detailed variogram. To produce a similar type variogram in coal, it is necessary to drill many dozens of holes with much of the core length consisting of overburden data which is frequently of only secondary importance. To apply geostatistics to coal, not only are many separate sample sites needed, but frequently a problem exists in that the interval distance between samples cannot be controlled with the ease that hard rock drilling intervals can be controlled where it is only necessary to cut core segments according to some preassigned interval of distance. Because the uses of existing coal deposit samples are frequently handicapped by irregular sample distances and lack of sampling density along certain directions needed for the development of variograms, the application of geostatistics to coal deposits frequently does not proceed with the same efficiency and rapidity as when these techniques are applied to ore deposits. Grid-fitting was developed by the writers, as a logical and evolutionary improvement over the long and successful application of geostatistics to coal seams.6,9 Grid-fitting combines the trending of variance as well as other aspects of probability theory to optimize informational yields from the commonly less productive data derived from coal exploratory programs. Grid-fitting is basically a technique where a hypothesis involving numerous grid patterns, where each pattern is of a given geometry, size and direction is repeatedly matched against actual sample data to determine which match results in the closest fit of the hypothesis to the data. To determine the closest fit, a special index known as a selectivity index was developed. The selectivity index is basically the product of the mean and variance of the variances contained within each of the grids. hence, if SI is the selectivity index then [SI = Xs E (S i - Xs) /N] where [X]s is the mean of individual grid variances Si2 for any pattern of given geometry, direction and size.

Jan 1, 1984

By F. J. Sotillo

"Scrubbing both horizontal (drum) and vertical (attrition) are considered simple unit operations in the beneficiation of phosphate ores. In general, the operating conditions are fixed at high solids content based on the experience of the engineering or equipment manufacturing company responsible of designing this beneficiation step. Nevertheless, scrubbing is a complex unit operation designed to clean the surfaces of phosphate mineral particles of slimes, break loose weak inclusions or attached particles of impurities, and break aggregates of clayish material. Therefore, it is considered that as high solids content as possible should be used to enhance particle-particle interactions (impact and rubbing) without taking into consideration the rheology of the system. However, scrubbing unit operations design requires studying the balance between the increase of particle-particle interactions with the cushion effect that may occur when slimes, clays and fines decrease the availability of free water increasing the apparent viscosity of the phosphate slurry up to that of a paste consistency. This paper presents data from laboratory tests to determine the best operating conditions for the design of these unit operations based on the highest P2O5 grade obtained with the lowest impurities for different size fractions. INTRODUCTION In the beneficiation of phosphate ores, unit operations such as horizontal scrubbing (drum) and vertical scrubbing (attrition) are considered simple unit operations. Therefore, little attention is given to the design of horizontal and vertical scrubbing during the basic engineering studies, and the detail engineering stage, the manufacturers recommending “standard” units and operating conditions based on their experience. Due diligence of several beneficiation phosphate plants at industrial scale indicates that a deficient scrubbing of the phosphate ore results in significant problems in downstream unit operations, such as classification, clarification, gravity separation, magnetic separation, flotation, dewatering, and filtration. Scrubbing is in fact a complex unit operation designed to clean the surfaces of phosphate mineral particles of slimes (clays and fines), break loose weak inclusions or attached particles of impurities, and break aggregates of clayish material. Two phenomena occur, the particle-particle interaction (impact and rubbing), and the rheological effects of releasing significant amount of fines into the slurry. Therefore, high solids contents are recommended to enhance the particle-particle interactions, which may result in a change in the rheological regime of the system due to the slimes, clays, and fines decreasing the availability of free water. This increases the apparent viscosity of the system up to that of paste consistency resulting in a cushion effect that suppresses scrubbing. Under these conditions, not all fines are release and rejected (deslimed), downstream unit operations being affected by the release of clays, resulting in P2O5 losses."

Jan 1, 2017

By W. J. Aitken

The pneumatic conveying of relatively large abrasive materials by dilute-phase conveying techniques has been applied in the underground mining industry for many years especially for backfilling mines and the hoisting of ore, coal, or rock out of the mines. The technique was extensively used in Europe, especially Germany and Britain for backfilling coal mines with rejects from the coal cleaning plants which not only helped to reduce environmental problems on the surface, but offered support to the overlaying strata in the deep underground mines, Similar techniques are being employed in the U.S.A. especially in uranium mines for the disposal of tailings, the main purpose being to extract a larger percentage of the ore from the pillars especially under weak roof conditions. Other than for the backfilling of abandoned mine entries, pneumatic conveying has not been applied in the mining industry in surface applications. In this paper, some consideration is given to three applications for open pit mining which may prove beneficial, namely hoisting coal up the high wall, sealing off auger holes, and stabilizing the high wall when being undercut by a longwall system.

Jan 1, 1981

By S. McAlister

This paper outlines the development of the Falcon enhanced gravity separator. Design objectives included continuous operation with sharp separations, mechanical simplicity, minimization of process water demand, the ability to apply a centrifugal field up to 300G&apos;s, unit capacity in excess of 100 t/h within a footprint of 10 square meters, a capital cost below $US 4,000 per t/h capacity, and total operating costs of less than $US 0.40 per tonne. A parallel development has been inexpensive, effective, semi-continuous equipment for recovery of precious metals in the free metallic state. These objectives have been largely met. There are significant opportunities for the technology in many mineral processing applications.

Jan 1, 1998