Search Documents

By Matthew S. Sanchez, Richard J. Lee, Matthew D. Zock, Drew R. Van Orden, Yumi Kamiya, Edward B. Ilgren

In many developing countries, asbestos is still used for friction products, insulation, and asbestoscement products. However, there is very limited modern data evaluating the airborne concentrations of asbestos fibers in operating asbestos plants. We have conducted an Industrial Hygiene survey, using state of the art PCM and TEM analysis, of a Bolivian asbestos cement plant that uses crocidolite during the production of roofing shingles and water tanks. The study is the first to use modern analytical measurements in an uncontrolled asbestos environment. Thus, this study offers insight into the historical airborne exposures at asbestos plants operating before modern dust control measures were introduced or airborne fiber levels regulated. The results suggest that fiber concentrations are far in excess of those for which current models would predict the onset of asbestos disease and mesothelioma. Significantly, the plant and community do not have an elevated incidence of asbestos disease or mesothelioma. Airborne fiber levels during comminution and fiber sizing ranged from 100 to as much as 1,000 f/cc. Fiber levels in the mixing, forming and finishing areas ranged from 0.5 to 9 f/cc. Based on the number of overloaded samples and estimates of their concentration, historical estimates of exposure may be underestimated by an order of magnitude. Also, an excellent correlation (1:1) between the PCM and TEM fiber concentrations (for fibers _0.25 um diameter) were obtained, raising questions about the conventional wisdom that the PCM systematically undercounts fibers. The results of this study further indicate that current models may overestimate the risk of asbestos disease and mesothelioma.

Jan 1, 2012

By V. I. Lakshmanan, Dan A. Mackie

Traditional vat leaching methods have had limited success, primarily due to the high cost of loading and unloading the vats. In general, such batch methods are labor-intensive and costly. Heap leaching has emerged as a viable, low- cost alternative, but low recoveries, normally in the 70% range, offer opportunities for improvement. Also increased regulatory guidlelines for effluent and spent heap leach pads disposal offer potential for alternative methods. The Mackie Vat Leaching Jig (MVLJ) has had its incubation at Ortech International, where bench scale through pilot scale testing continues. Design developments and testwork over the past two years indicate that the time may be right for field trials.

Jan 1, 1990

By J. A. Mielczarski

Surface properties of minerals could be modified selectively and very specifically by adsorption -desorption (dissolution) processes. This requires a monitoring and control of the outermost surface layer at a molecular and atomic level. The nature and structure of self-assembled submonolayers and monolayers at the interface of minerals were studied by infrared reflection spectroscopy. The external reflection spectra of the adsorbed monolayers on any type of minerals: transparent, opaque or non-transparent, recorded at different angles of incidence and for two polarizations are an excellent source of information about the nature and surface distribution of the adsorbed species. The developed method allows to obtain detailed information at a molecular level about the adsorbed surface species. By combination of the simulated and experimental data, the qualitative description of the adsorbed species as well as quantitative evaluation of orientation and the thickness of the adsorption layers were obtained. This fundamental knowledge allows to determine the mechanisms of surface phenomena which govern selective separations. Examples of different surfactant - mineral systems and industrial applications will be discussed.

Jan 1, 2000

By M. Zuckerberg, E. Mader, R. Pasyar

We describe a new software product designed for the net present value optimization of multi-open-pit blended ore operations in which it is desired and/or necessary to dump some or all of the waste rock produced in the course of operations back into the voids created in the process of ore extraction. The software product simultaneously decides over the entire life-of-mine which material to mine in which year, once mined what to do with it, and where to put that material which it has decided to waste, all subject to annual blend and capacity constraints.

Jan 1, 2007

By Verya Nasri, Agustin Rey

Once completed, the Montreal Réseau Express Métropolitain (REM) will be the fourth largest automated transportation system in the world. The REM represents construction costs of approximately 7.0 billion Canadian dollars. The project consists of 67 km of twin tracks over four branches connected to downtown Montreal. The project includes 26 stations with 3 underground stations in downtown Montreal. One of the underground stations was built using the NATM method with thin permanent shotcrete initial and final liners separated by a sprayed on waterproofing membrane. The 2 other underground stations were built with the cut and cover approach including one using permanent secant pile wall with permanent walers and struts as the support of excavation and the final perimeter wall of the station. The project also includes the rehabilitation and enlargement of the Mont Royal Tunnel. This 100-year-old double track tunnel is about 5 km long. The REM also consists of 3.6 km new TBM tunnel connecting downtown to the Montreal International Airport through saturated soft ground and karstic rock. By the time of RETC, the construction of REM underground structures will be completed. This paper presents the design and construction aspects of the underground structures of this mega project.

Jun 13, 2023

By Z. T. Mathe, M. A. Vera, M. C. Harris

This contribution presents a methodology how to quantify froth zone recovery in a continuously operated laboratory mechanical flotation cell. The methodology consists of relating the overall flotation rate constant to the froth depth of the flotation cell. As a result, a froth zone recovery factor (Rf) can be extracted. This froth performance parameter has been studied as a function of the flotation cell operating variables. By understanding the effect of these operating variables on Rf, an integrated methodology for modelling froth zone performance in batch and continuously operated laboratory flotation cells has been proposed. The Rf modelling is based on a semi-empirical approach which considers a number of parameters to be used. Some of these parameters may have physical significance, i. e. they may be easily and physically measured. The modelling approach consists of taking into account the interaction between the pulp and froth zones. This interaction allows froth zone recovery (Rf) to be predicted. The whole modelling exercise process lies on auxiliaries relationships which indicate the dependence of the parameters with the operating conditions of the flotation cell. This contribution is part of a larger project that deals with the modelling and optimisation of flotation plants (Project P9L, 2000).

Jan 1, 2001

By Franz Albert Nonnen

Backfill systems have been used for as long as mining activities have existed. Various backfill methods have been developed over the centuries with consideration for geological necessities, the technical means available, security requirements, and available finances. In the past, backfill systems were introduced and upgraded geographically in accordance with local experiences. In modern times, mining engineers participate in international forums for the exchange of knowledge so that backfill techniques and experiences are shared concurrently in mining areas all over the world. Mine backfilling increases the cost of mining so that great attention must be paid to choose a low-cost, reliable, and low maintenance backfill system. Some methods are described in this paper.

Jan 1, 2001

By David R. Gossett

For the 22nd year, the chance to exchange knowledge, experience and business cards drew hundreds of mining and phosphate professionals for a two-day regional Phosphate Conference in Lakeland, Florida Nearly 400 people participated in the October conference, which focused on the phosphate industry?s future success. There were 41 exhibitors, 13 program advertisers and 23 sponsors among those supporting the conference. It was chaired by David Gossett, 2006-2007 SME Florida Section Chairman. In the opening panel session that he chaired, John Garlanger (SME) of Ardaman and Associates posed the questions; ?How successful has the industry been? How do we measure it and what factors contributed to the industry?s success? How long will the ethanol boom last? Can the industry obtain the permits it needs to mine for the next 30 years? Can the industry attract and retain the quality of workers it needs??

Jan 1, 2008

By Sabina Brady

Nearly a decade and a half after the US and China established formal diplomatic relations, and two decades after the two countries signed the Shanghai Communique and established commercial ties, the world, and perhaps China itself, has discovered that a wealth of natural mineral and energy resources lie beneath China's soil and directly off its coast. The country's coal reserves and oil and gas potential are well known. Its ferrous and nonferrous metal reserves are respectable and in a number of instances pre-eminent. According to 1981 Minerals Yearbook estimates - more often than not below those now being claimed by China - the country's aluminous metal reserves are about 907 Mt (1 billion st); iron ore reserves are 40 Gt (44 billion st); and copper reserves are about 46 Mt (54.4 million st) of contained metal. In addition, the country has about 10.7 Gt (11.8 billion st) of phosphate reserves, the fourth largest in the world, and 3 Gt (3.3 billion st) of pyrite. China's national Sixth Five Year Plan promulgated in late 1982 ended a stringent three-year retrenchment or readjustment period in which a number of major development projects involving foreign participation initiated in the late 1970s were shelved. The new Five Year Plan is a signal both within and outside of China that things are now moving again, and that major industrial and service sectors are receiving the kind of funding and flexibility they need for expansion, construction and modernization. The new plan's strategy for growth is measured and much less grandiose and frenetic than it was five years ago when China flung open its doors to foreign companies and invited participation in large-scale development projects. Now, the country's reticence to spend foreign exchange to purchase key equipment, technology, and services -a reaction to these projects and the spending they entailed - is clearly on the wane. In China's effort to quadruple its GNP by the year 2000, there is a new willingness to use some of its substantial foreign reserves. In fact, it is projected that 1983 will witness a $1.9 billion deficit, with a $2-3 billion deficit in 1984 and 1985. The following article discusses implications the Sixth Five-Year Plan has for nonferrous metal development in China. It is the first in a series of three articles on Chinese mineral resource development to be published in Mining Engineering over the next few months. The second article will identify specific nonferrous projects underway, while the third in the series will focus on trade and development opportunities for phosphate and potash producers in China. China's Ambitious Plans In the last few months, the exploitation of China's nonferrous resources and development of its industrial processing capabilities have begun to receive increasing attention on both provincial and central levels. Unlike the earlier modernization drive of 1978 when China's ferrous sector - best typified in the Baoshan iron and steel project - got the lion's share of the Ministry of Metallurgical Industry's (MMI) energy and resources, it now appears that in some respects the nonferrous and industrial sectors are finally moving out from beneath the dominating shadow of ferrous and getting their own day in the sun. Separation of Nonferrous from Ferrous One clear demonstration of this is the establishment in April 1983 of the China Nonferrous Metals Industry Corporation (CNFMIC). The corporation is composed of 819 enterprises with over a million workers, and also includes 12 nonferrous metal construction companies, eight design institutes, and three prospecting companies. Of ministerial rank, CNFMIC is responsible for the development of both the country's nonferrous resources and its processing facilities. Although closely tied to the parent ministry from which it sprang (i.e. MMI), CNFMIC, at least theoretically, is separate and independent from it. One strong indication that this independence is, or soon will become a reality, can be seen from the fact that the new corporation is not headed by the former MMI officials, not even those who made up the ministry's now defunct nonferrous bureau. Instead, its president Qiu Chunfu is formerly of the State Economic Commission and the China International Trust and Investment Corp. Its general manager Fei Ziwen, an engineer in his early 50s, is from the Jiangxi Province Copper Corp. The new nonferrous corporation appears to be powerful

Jan 7, 1983

By G. T. Lineberry, L. Adler

Due to safety-imposed constraints on clearances for mobile bulk handling equipment, it is necessary to optimally select a unit based on speed and size. The unit cannot be both large and fast. Since output is proportional to both size (or capacity) and speed, the combination must be carefully examined to maximize output. A simple graphical procedure and a calculus-based solution are presented to accomplish this. While the procedure applies to all mobile bulk handlers, as an example of the solution technique, attention is focused on shuttle cars. Background Major variables To fully define a bulk handling problem, the conditions, equipment, and activities must be characterized. The conditions and activities, when lumped together, are termed "encumbered space," since they "act to impede motion, as with a burden" (Lineberry, 1979). The insertion of mobile bulk handling equipment into what is already a difficult set of conditions and activities compounds the state of encumbrance, as limited space is competed for by many normal and life support systems. Long (1972) recognized the effects of design criteria, including road width, on haulage vehicle speed and, therefore, on production. Velocity -clearance curves Velocity-clearance curves are either available or can be constructed in the field. A preliminary set of curves for average conditions and activities is shown in Fig. 1, where clearances are only for the side of the vehicle (Lineberry and Adler, 1984). These curves set the safe speed limits for a vehicle operating at given clearances, under given conditions and activities. When feasible, velocity-clearance curves should be constructed through field measurement and observation. Curve construction should also consider haulway roughness, distances, and operator skill, as well as loading and dumping characteristics. It should be noted that haulage capacity determination is a total systems problem, not one just dependent on velocity and clearances. Production requirements and company capabilities also influence capacity determination.

Jan 10, 1985

By T. Clarkin

This paper presents a hydrologic closure design concept to minimize the risk of water discharges from closed mine tailings facilities. It evaluates the applicability of U.S. Nuclear Regulatory Commission guidelines to develop acceptable designs for the closure of tailings facilities that have a calculated adequate surcharge capacity for environmental protection and an emergency spillway for dam safety. The guidelines provide a basis to estimate an acceptable surcharge capacity of a Probable Maximum Flood series for storage of surface runoff. To be conservative and for redundancy with respect to dam safety, an emergency spillway is provided to pass the Probable Maximum Flood. Depending on the annual water balance, the surcharge capacity may be used by surface runoff and minor amounts of sediment that accumulates in the impoundment from year to year. The emergency spillway crest is then set at this level or above the surcharge capacity, whichever is higher. An example is given of the active Red Dog Mine tailings facility in Alaska where this method was used for the preliminary design of the tailings main dam at its ultimate closure configuration.

Jan 1, 2012

The Earth?s population is approaching 6.6 billion people. More than half live in urban areas. And, as those figures continue to grow, the need to make wise use of the world?s natural resources as well as its living space will also grow. Thus, the concept of sustainable development ? meeting the needs of the current generation while preserving resources for future generations. The use of underground space is only one part of the sustainable development concept. But it is an important one. Tunnels and underground space are environmentally friendly and contribute significantly to sustainable development. But it takes years to plan and build tunnels and other underground infrastructure. And the demand for infrastructure in the world?s mega cities has grown significantly. In December, about 100 people representing several developed and developing nations spent a day at the United Nations (UN) in New York City discussing the future of underground space development throughout the world. The meeting was put on by the UN?s Department of Economic and Social Affairs and the International Tunnelling and Underground Space Association (ITA). The conference was titled ?The Use of Underground Space as an Unexpected Solution for Promoting Sustainable Development.? Its aim was to promote practical solutions to the use of underground space and tunnels as feasible alternatives to promote sustainable development throughout the world. A panel of speakers from government, academia, the UN and the ITA stressed that development is not sustainable without infrastructure. And, as the world?s population grows, there is now an urgent requirement to efficiently plan for the use of underground space to preserve it for the future benefit of mankind. The benefits of the use of underground space are many, they said. Among them: ? Tunnels channel clean water in and waste water out. This promotes health and sustainability worldwide, particularly in developing countries. ? The use of tunnels and underground space helps conserve energy and increases its efficient use ? the use of tunnels cuts commuting time and so saves energy. ? Tunnels, microtunnels and other underground structures promote the more efficient use of space in large cities ? the bulk storage of water, fuel and other goods. ? Underground structures are subject to less stress than surface structures, making them safe havens for natural and man-made hazards, including earthquakes. And, because underground structures are more durable, lifecycle costs are less than surface structures. ? Underground structures promote the multiple use of available land. Land owner-ship at several layers increases land use and provides more usable space. Han Admiraal is director of the Center for Underground Construction in the Netherlands. He said that urban planners need a new vision concerning the use of underground space. Going underground protects historical and archaeological surface facilities, he said. Underground space use can also protect populations located in adverse climates. And sensitive environmental areas on the surface can also be protected from development. In addition to the transportation of people, freight and water, underground development can also store water, as well as provide storage for waste, hazardous materials, carbon dioxide and geothermal energy. The upshot of this new awareness and vision for under-ground space is that its use should be considered before surface development, Admiraal said. And planners and developers are placing more emphasis on underground space development as part of their overall development plans for urban areas. That was not always the case, he said. In the past, underground space was not considered until after the surface space had run out, he said.

Jan 1, 2008

By W. C. Goldberg, E. M. Frizzell

Monitoring slope displacement in open-pit mines can help predict collapses and prevent serious damage, injuries, and fatalities. Early detection of movement may indicate the need to modify slope geometry, initiate dewatering if the slope is wet, or consider artificial support measures such as cable bolting. Slope monitoring at the Berkeley pit was carried out with varying degrees of intensity and continuity for about 15 years. Some of the old mine records are still intact and accessible. Slope monitoring data can therefore be collected and published for the benefit of other mine operators. Because prediction of slope failures is empirical in nature, publication of several well documented case studies will be a valuable contribution to the industry. Background - Berkeley pit Open-pit mining of copper from the Berkeley pit, located on the east side of Butte, MT, began in 1955 and ceased in 1982. During that time, about 1 Gt (1.2 billion st) of material were removed to form a pit about 1.8 km wide by 2.1 km long (6000 ft by 7000 ft) at the rim, and 550 m (1800 ft) deep as measured from the high hill on the northwest side. From the south side, the pit only measures 365 m (1200 ft) deep. The Berkeley pit was first owned and operated by Anaconda Minerals Co., and subsequently by Arco. Following its closure in April 1982, the mine began to fill with water. Washington Construction purchased the property in 1986, and Montana Resources Inc. began mining to the east of the Berkeley pit in July 1986. Numerous instances of slope failure were recorded during the course of mining and several intensive geotechnical investigations were conducted in an effort to optimize the mine design. One of the last and most comprehensive studies was initiated in 1977. For purposes of geotechnical analysis, the mine was divided into nine design sectors on the basis of geologic conditions, geographic orientation, and economic importance (Fig. 1). Only two of these sectors - the concentrator and the southeast corner - are considered here. Material properties were obtained from several studies of samples collected from the mine and adjacent areas. The slope was monitored using standard surveying techniques to record the amount of movement in an area. The

Jan 1, 1989

By Dean Brox

The use of Tunnel Boring Machines (TBMs) for tunnel construction of long tunnels in the Andes of South America has been of mixed success in the past due to a variety of reasons and key lessons can be recognized. A review of past TBM tunnel projects in the Andes has unveiled some interesting findings for different TBM tunnel approaches with both world records of progress as well as nearly in-completed projects with machines being abandoned. Key considerations for the use of TBMs for tunnel construction in the Andes include geological issues; (faults, rock type, rock strength, rock abrasivity, durability, groundwater inflows),depth of cover and the potential for overstressing/rockbursts, site access and terrain, portal locations, intermediate access possibilities, minimum tunnel size, support requirements, contractor and labour experience, and project schedule demands. TBMs offer highly recognized schedule benefits(high progress, no concrete lining) for a project if intermediate access adits are limited as well as hydraulic benefits for water conveyance projects. Minimum specifications for TBMs can be easily developed to suit the unique requirements of any project so as long as all factors are carefully considered. The overall conditions and factors associated with some projects may suggest that it is not appropriate to use TBMs due to a perceived high risk. Finally, access for geotechnical investigations by drilling in the commonly steep terrain of the Andes is typically difficult and often not impossible. Alternative approaches for geotechnical investigations for TBM tunnels including comprehensive mapping, high-resolution airborne electric-magnetics for delineation of possible fault zones, and rock block sampling is presented and discussed.

By E. Fahrenkrog, D. Sbartaro, E. N. Cifuentes

An intelligent supervisor using expert system tools and applied to a crushing plant has been developed with a structure based on a model of a human operator. It consists of a knowledge base containing a qualitative model of the process and a rules base with the heuristic logic used by an operator when supervising a plant. The simulation results obtained show the potential of this type of system to supervise the automatic operation of a plant. There has been very significant development in artificial intelligence over the last two decades. Within this development, two approaches can be distinguished, (Winston, 1984). The "model approach," in which the main objective is to understand and model the be¬havior of living systems. The second approach is the "engineering approach." Here, systems capable of performing tasks usually requiring human intelligence are created. As part of this latter approach, knowledge engineering and its main achievement, expert systems, have been developed. Expert systems arose from the need to incorporate the abilities of a human expert in solving realistic problems in which the conventional approach has great difficulties. The first successful applications of expert systems were in medical diagnosis, geophysics, and fault detection. However, since 1971, when Fu (1971; defined intelligent control as the inter action of artificial intelligence and automatic control, some significant developments in the use of artificial intelligence tools for process control have been achieved (Astrom, 1986; Pinto 1988; Fahrenkrog, 1988; and Porter 1987). The modern control theory has made important advances. And, although successful in some applications, it has failed to cope with the practicalities of many industrial processes. As a result, the automatic operation of a plant has been confined to a small region around a normal operating point and to periods without any great disturbance. One of the main reasons for this is the lack of accurate and structured knowledge of the processes involved. Despite this, operators applying their knowledge, experience, and a little intuition, often obtain good results controlling the plant in such situations. Considering the above, the next obvious step is to include similar reasoning capacities in a computational system. The development of such an expert supervisory system prototype applied to a mineral crushing plant is presented. Problem description The problem is to conceive a control system with the ability to handle quali-

Jan 1, 1989

By Clay Haynes

While the Kansas River Tunnel is a relatively short, small diameter tunnel, the shaft excavation methods implemented were long and large on innovation and use of reverse circulation drilling equipment. ATS Drilling, L.P. used mechanical excavation techniques for both soil and rock segments of the 42.7 m (140 feet) and 38.1 m (125 feet) deep shafts that were 2.9 m (9.5 feet) and 4.1m (13.5 feet) diameter, respectively.

By R. Mier

The metals and minerals mining industry has evolved dramatically from the earliest objects ever made out of native copper circa 9,000 BC to the modern developments we see today. To better appreciate past developments and to get a sense of where the industry is heading, a brief overview of mayor industry highlights over the last 100 years will be presented, followed by a discussion on potential global scenarios and by a review on mayor industry trends.

Feb 27, 2013

This geometallurgical study examines the gangue mineral variability at the Bingham Canyon porphyry copper mine in Utah. Understanding an orebody?s mineralogy is important for mine and mill planning because it provides information on the size, texture, and distribution of ore minerals, the relationship between ore and gangue minerals, and the extent and type of alteration. Quantification of the mineralogical variability and properties of an orebody provides valuable input to the ore model and may have a significant effect on recovery optimization. This study was designed to be carried out on an initially detailed scale in order to develop a robust methodology for measuring and quantifying specific parameters, such as the distribution of mineral phases, alteration assemblages and fractures from key ore domains at the Bingham Canyon mine (Figure 1). Details of the methodology are reported below. This technique can be applied to testing the impact of mineralogy on a number of processing parameters. [ ] Figure 1. Ore domain map of Bingham Canyon (Kennecott Utah Copper, 2003) showing the 33 geometallurgical ore domains. The samples for this study were collected from the northwest part of the deposit circled on the map. PROJECT BACKGROUND Geology The Bingham Canyon deposit is a large porphyry Cu-Mo-Au deposit with associated skarn and base-metal replacement deposits mined in an open-pit mine measuring about 2.5 miles across and 4,000 feet deep. The deposit is hosted by the Bingham Stock, a Late Eocene to Mid-Oligocene intrusive complex. The skarn is hosted by the Late Carboniferous-age Bingham Mine Formation, which is comprised of quartzites and basal limestones (Babcock Jr. et al., 1998). The Bingham Stock is a composite intrusive complex that was emplaced over a period of about two million years. The oldest phase is described as a fine-grained equigranular monzonite (MZ), which intruded the country rocks at 39.8 ± 0.4 Ma (U-Pb zircon TIMS age) (Parry et al., 2001). Subsequently, the quartz monzonite porphyry (QMP) was emplaced, followed by intrusion of a latite porphyry (LP). The final intrusive phase, which forms narrow dikes that crosscut the Bingham Stock, is represented by a quartz latite porphyry (QLP), which is dated to 37.5 ± 0.4 Ma by 40Ar/39Ar dating of sanidine (Deino and Keith, 1998). Also present, are a minette dike in contact with a QLP dike (Waite et al., 1998; Deino and Keith, 1998), and a biotite porphyry (BP), a quartz latite porphyry breccia (QLPbx), and a pebble dike (Redmond, 2002). The copper orebody is centered above the Bingham Stock and forms an inverted cup shape with three high-grade copper zones extending to depth. Molybdenite mineralization occurs within and extends below the copper orebody, but is not correlated with copper mineralization. The main sulfide assemblage is chalcopyrite, bornite, molybdenite, and pyrite. Gold is locally intergrown with chalcopyrite and bornite (Babcock Jr. et al., 1998; Phillips et al., 1998). The surrounding country rocks host skarn deposits with three main ore types - garnet skarns, massive sulfides, and iron oxides. The garnet skarns contain chalcopyrite and pyrite with magnetite veins. In the massive sulfides chalcopyrite and pyrite occur either in banded sulfides or in unconsolidated microbreccias. The iron oxides contain disseminated chalcopyrite with minor chalcocite and bornite (Harrison and Reid, 1998). The deposit is overprinted by several stages of alteration. Potassic alteration is concentrated at the center of the deposit. It is surrounded and partially overlapped by a propylitic alteration zone. Both zones are overprinted by sericitic alteration. In the northern part of the deposit evidence for argillic alteration can be found (Bowman et al., 1987). Similarly, the skarn deposit was also overprinted by several stages of alteration: wollastonite, idocrase, and garnet in cherty limestones, and quartz and diopside forming in calcareous quartzites. Distally, diopside was replaced by talc, tremolite, dolomite, secondary calcite, and pyrite, and quartz and sulfide veinlets with biotite and actinolite selvages are present. Andradite garnet, diopside, quartz, magnetite, hematite, and copper sulfides were overprinted by wollastonite (Babcock Jr. et al., 1998). Because the monzonite, quartz monzonite porphyry, latite porphyry, and quartz latite porphyry host the bulk of the mineralization, our research is focused on these lithologic units. Geometallurgy On the basis of geological (lithology, alteration assemblages, fracture density, copper mineralization) and metallurgical properties, the deposit has been divided into 33 ore domains by mine geologists and metallurgists (Figure 1). In map view, these domains cross geologically defined boundaries (MZ, QMP etc.). These domains reflect regions of the deposit that have particular, mapable attributes or properties. They reflect a combination of geological and mineralogical characteristics that combine to impact processing. Alteration, for example, as shown by talc mineralization, is one such key feature. Hardness may reflect the absence of sericitic but presence of potassic alteration. Structural discontinuities such as faulting, fracturing, or development of void

Jan 1, 2009

The Colorado portion of the Rio Grande rift is clearly defined physiographically from the south in the San Luis valley northward to the latitude of Leadville where sediments of the Dry Union Formation (Tweto, 1961) accumulated within the subsiding rift zone. To the north of Leadville is a system of faults active in the late Tertiary, including the Mosquito fault that offset a portion of the Climax mineralization (Wallace et al., 1968). Tweto (197B) describes remnants of Dry Union Formation against the Mosquito fault north of Dillon in the Blue River valley, so it is apparent that the rift and associated sediments extended well to the north of Leadville. Kelley (1952, 1954, 1956) and Chapin (1971) have noted in New Mexico that the Rio Grande rift is a series of en echelon basins, offset to the east, with constrictions connecting them (Fig. 1). In Colorado the structural basins are offset to the west. The net effect of all the rift zone basins in New Mexico and Colorado is an arcuate pattern (Fig. 1) abutting the Colorado Plateau and Sari Juan Volcanic Province on the west. The width of the rift system gradually decreases northward to about Leadville where rift definition is not apparent.

Jan 1, 1987

By G. P. Tomaino

Talc is a layered, hydrous magnesium silicate mineral. It has a soft, soapy feel and typically a smooth texture. Talc is also known for its insulation, heat resistance, chemical stability, oil absorption and strong covering quality. Talc, Mg3Si4O10 (OH)2, has a theoretical chemical composition of MgO at 31.7 percent, SiO2 at 63.5 percent, and H2O at 4.8 percent. However, talc’s chemical and mineralogical composition can vary depending on its geological history/parent rock association. These mineral associations and variable levels are usually chlorite and carbonates (magnesite, calcite and dolomite). Two key elemental substitutions that can occur in the talc crystal structure are iron for magnesium and fluorine for hydroxyl. These compositional differences may limit or enhance the talc’s usage in specific market niches. The United States remains self-sufficient in most grades of talc.

Jan 1, 2005