Search Documents

By Wolfgang Roth

In 1990, a residential area above the North Outfall Sewer (NOS) tunnel constructed in 1924, experienced subsidence. After sewage was diverted into the North Outfall Replacement Sewer (NORS), soil probing from within the tunnel was conducted, soil-improvement options were developed, and a preferred grouting scheme was analyzed by numerical modeling to evaluate the stability of the 80-year+ old tunnel liner under grouting-induced loading conditions. This paper discusses the initial field investigation and the development and analysis of a grouting scheme originally intended to be implemented before relining of the tunnel. The scheme was later modified, and the new liner was installed before the final probing and grouting work was done.

Jan 1, 2008

By Tim O’Neil

If you build a big truck, build a big tire to match it. Let that haulage synergy aid the economics, productivity and lessened maintenance for the unit. Now, Cater-pillar and Michelin have done just that. Discussions began in 1996. Caterpillar was making plans for its 797 ultra-class haul truck. The development team realized the need for a tire that could withstand extreme loads. The 797 would weigh 558 t (615 st) and be capable of 64 km/h (40 mph) speeds. So Caterpillar approached Michelin. The two companies realized the benefits of jointly developing a tire for the 797.

Jan 1, 2002

By P. Roghanchi

The Rock Mass Rating (RMR) system is an internationally recognized classification system that can be used for preliminary ground control design. The RMR system assigns quantifiable values to predefined classified parameters of a rock mass. Assigning a single value rather than a range to each parameter is a source of uncertainty, however, assigning a single value can be useful for further studies related to RMR ratings. Fuzzy systems are being used in an increasing number of application areas where linguistic rules are used to describe the system. In past decades, fuzzy systems have been successfully used in geotechnical and mining engineering problems to cope with uncertain data as well as with vagueness. In such scenarios, linguistic rules and rating-based classification of rock masses have always been questionable. The objective of this study is to apply fuzzy set theory to the RMR classification system. The fuzzy system proposed in this study is specified for weak and very weak rock masses (RMR<50) based on data collected from Nevada gold mines where 68% of RMR data is in the ?poor? and ?very poor? classes. In this approach, a Mamdani fuzzy algorithm has been constructed to evaluate basic RMR89 rating for the ?wet condition.? Comparison between basic RMR89 and fuzzy RMR shows the fuzzy RMR system is valid to predict RMR from the discrete rating of each input parameter.

Feb 27, 2013

To build an effective entry roof beam, a roof bolting or supporting system must be of the ability of providing a clamping force to the bolted roof strata. Currently, two roof bolting systems are widely used to serve the purpose of providing such a clamping force. They are resin and mechanical anchorage bolting systems. Both numerical modeling and double shear testing results indicate that a greater pre-installed load or pretension of a roof bolting system is very critical for effective beam building. Although it?s generally accepted that a mechanical anchorage bolting system can provide a greater pretension than a resin anchorage bolting system does (Su and Poland, 2007 and Peng, 2008), no published field data are available to support such a conclusion. This paper analyzes the results of our field tests on both roof bolting systems, explains why one roof bolting system is better than the other under a typical roof condition, and finally discusses the effective means for coal mine operators to determine the best roof bolting system for their roof conditions.

Jan 1, 2011

By Frank C. Stevens

Many changes have taken place in the "World Cement Market" since Joseph Aspdin discovered portland cement in the early 1800&apos;s. At the turn of the century, production of cement world wide was a few million tons; today, it is over one billion tons. By 1995, world production is estimated to reach 1.2 billion tons. Cement processing has changed from inefficient, small vertical kilns to large efficient, precalcining kilns, and large automated crushing, blending and grinding systems. Consequently the cost of production has declined in real terms, resulting in significant economic benefits to the general public. In addition, quality and uniformity of cement have increased, strengths have increased, and at least 25% fewer pounds of cement are needed for each cubic yard of concrete. Today, cement moves thousands of miles on the inland rivers and great lakes of the U. S., across Siberia and across the oceans of the world. The volume of cement moving more than a few hundred miles is almost 100 million tons, or 10% of world production. Today, on a per ton basis, it costs no more to move 40,000 tons of cement to the United States from the Western Pacific rim or from Europe than it does to truck cement 200 miles. For example, cement shipped by water from Spain costs $5.00 to $7.00 per ton compared to cement shipped by truck 200 miles at $16.00 per ton. This low cost water transportation has been a major factor for the increased movement of cement between countries. Table 1, Cement Production Summary-World, gives a global picture of production, export and import tonnages in recent years. Figure 1 is a graph showing CEMENT PRODUCTION SUMMARY WORLD WIDE.

Jan 1, 1987

By D. Kwietnewski

The 4th bore of the Caldecott Tunnel is a 50-ft horseshoe shaped highway tunnel located in the hills east of Oakland, California. Tunnel excavation was mostly completed using one of the world?s largest commercially available roadheaders, a Wirth T3.20. The geologic profile included seven different geologic units, which displayed a range of different behavior with regard to excavation and initial support. Following a brief introduction to the excavation and support methods, this paper will discuss roadheader performance in the various geologic units encountered during excavation. Comments will also be made concerning the relationship between the roadheader method of excavation and observed ground convergence during excavation.

Feb 27, 2013

By C. Demir, M. S. Celik, I. Gülgonul

Na-feldspar (albite) and K-feldspar (microcline or orthoclase) are major feldspar minerals with identical crystal structures and physicochemical properties. Flotation appears to be a unique method of separating these minerals. Fundamental studies on amine/feldspar system in the presence of monovalent salts showed that separation of these feldspar minerals by flotation is possible at certain concentration of monovalent salts in HF medium and natural pH. A comparison between natural pH and HF medium indicates that the latter provides a better selectivity at the expense of higher collector requirement. A general mechanism for both systems involving an ion exchange between the uncommon ions and adsorption of the common ions is proposed to be responsible for creating differences in the charge of albite and microcline unto which amine adsorbs.

Jan 1, 2002

By Rex E. Loesby

The dramatic increase in molybdenum prices from the low of less than $2.50/lb in 1999 to more than $40/lb in 2005 has caught the attention of molybdenum mine owners and exploration project developers. Between 2005 and early 2007, prices pulled back and stabilized within a trading range of $25/lb to $30/lb. This 1,000 percent price increase has motivated most existing producers to expand production and is motivating those with molybdenum prospects to accelerate the development process for earliest possible production. It is still unknown how much new production will come from existing mines, how much production will be needed from new mines if demand continues to grow and how many potential new mines might be available to meet future demand. And of course, the billion dollar question is whether molybdenum prices will remain high, or will they fall back to the low levels seen during the 1980s and 1990s? This article attempts to answer these questions in a way that will help molybdenum project developers and financiers plan for the future.

Jan 1, 2007

The OptiPit® software program is developed based on expertise gained at the Colorado School of Mines (CSM) using Mixed Integer Linear Programming (MILP) techniques. This program has been developed to satisfy the need in the mining industry for a multi-time period schedule and cutoff grade optimization tool that handles large scale open pit and underground mining operations involving many dumps, stockpiles, complex processing options and blending requirements. The current software (or earlier development versions) has been beta tested and used on various large scale projects within Placer Dome Inc., Newmont Mining Corporation, and Phelps Dodge Corporation since 2003. Through the use of this software, these companies experienced additional value creation by optimizing mine sequences, cutoff grades, material process flows and stockpiles under complex operational and processing constraints. This paper will present simple case study results to demonstrate the power of OptiPit® when used as a cutoff grade optimization tool. Furthermore, the paper will show, by example, how significant the difference in the Net Present Value (NPV) of a given project can be, depending on whether results are obtained by way of cutoff grade optimization using OptiPit®, or by using traditional breakeven cutoff grade approach.

Jan 1, 2007

By J. D. Bittner

The ST separator utilizes electrical charge differences between materials produced by surface contact or triboelectric charging. When two materials are in contact, material with a higher affinity for electrons gains electrons and thus charges negative, while material with lower electron affinity charges positive. This contact exchange of charge is universally observed for all materials, at times causing electrostatic nuisances that are a problem in some industries. Electron affinity is dependent on the chemical composition of the particle surface and will result in substantial differential charging of materials in a mixture of discrete particles of different composition. In the ST separator (Figures 1 and 2), material is fed into the thin gap 0.9 ? 1.5 cm (0.35 -0.6 in.) between two parallel planar electrodes. The particles are triboelectrically charged by inter-particle contact. For example, in the case of coal combustion fly ash, a mixture of carbon particles and mineral particles, the positively charged carbon and the negatively charged mineral are attracted to opposite electrodes. The particles are then swept up by a continuous moving open-mesh belt and conveyed in opposite directions. The belt moves the particles adjacent to each electrode toward opposite ends of the separator. The electric field need only move the particles a tiny fraction of a centimeter to move a particle from a left-moving to a right-moving stream. The counter current flow of the separating particles and continual triboelectric charging by carbon-mineral collisions provides for a multi-stage separation and results in excellent purity and recovery in a single-pass unit. The high belt speed also enables very high throughputs, up to 40 tonnes per hour on a single separator. By controlling various process parameters, such as belt speed, feed point, electrode gap and feed rate, the ST process produces low carbon fly ash at carbon contents of 2 % ± 0.5% from feed fly ashes ranging in carbon from 4% to over 30%.

Feb 27, 2013

By William H. Hansmire

The Modified Detroit River Outfall No. 2 (MOD DRO-2) will discharge treated wastewater to the Detroit River. Construction of a 6.4-m-diameter, 1.9-km-long tunnel was halted in 2003 by flooding during tunneling with an open face hard rock TBM. A new design for a higher rock tunnel, a ?Modified? design, was completed in 2007 and Notice to Proceed to the tunnel contractor was given in November 2008. Project duration is four years for completion of tunneling and start of outfall tunnel operation. This tunneling project has high groundwater pressure (5 bar), pervious limestone rock of up to 140 MPa (20,000 psi) strength, and hydrogen sulphide in the groundwater. The new tunnel will be connecting to access shafts and outfall diffuser riser shafts previously built for the now-abandoned tunnel. The new tunnel design construction contract, and initial planning to use a pressurized-face (slurry) hard rock TBM are presented.

Many investigators measured surface forces between hydrophobic macroscopic surfaces using atomic force microscope (AFM). Some investigators observed long-range attractions and attributed them to the presence of hydrophobic forces, while others suggested that they are artifacts of the nano-bubbles and cavities associated with the hydrophobic surfaces. Still others suggested that the long-range attractions are due to the electrostatic interactions between charged patches present on opposing surfaces and hence are unrelated to surface hydrophobicity. In the present work, we have measured long-range attractions between gold- (or silver-) coated surfaces hydrophobized in potassium ethyl xanthate (KEX) solutions at pH 9.2 under controlled potential conditions. The results of our AFM force measurements are consistent with those of the contact angle and voltammetry experiments, indicating that the long-range attractions are hydrophobic forces.

Jan 1, 2012

By D. A. Norrgran, J. A. Wernham, D. E. Walsh

A qualitative test program was sponsored jointly by the University of Alaska and Eriez Magnetics, in order to study placer gold nugget recovery using an eddy-current separator. Various gold nuggets from Alaska, ranging from 6.4 mm to 63.5 mm in size, were tested. All testing was performed using an Eriez Laboratory ESC, Model REA, fitted with 2000 gauss, surface field strength magnetic rotor. The belt speed was set to 91 meters per minute and the rotor speed was set to 2500 rpm in the forward direction. The splitter was adjusted to just reject the largest pieces of rock that measured an average 76 mm x102 mm x 127 mm. Based on the results of this limited test work, it can be recommended to placer gold mine operators, that Eriez Magnetics ECS technology is a viable and practical concentration technology for coarse gold recovery. Silver and platinum were also tested.

Jan 1, 2003

By R. Tamblyn

Vertically stirred media mills are a highly effective low-footprint solution for the ultrafine grinding of industrial minerals. This work investigates the effect of media density on flow patterns within the mill. Direct irradiation of a media particle leads to decay through positron emission, consequently forming two anti-parallel gamma rays, which allow for the real time tracking of particle position. Grinding media of the same size, but with a range of specific gravities are followed using this method, and the effect on the flow within the mill is revealed. The technique is seen to be an effective method to highlight the velocity profiles within the mill, as well as the zones where grinding is less efficient ? areas of relatively low velocity and high residence time. The changing media is seen to effect the overall flow patterns within the mill, having consequential effects on the efficiency of the grind.

Jan 1, 2009

By A. D. Davis

Limestone-based material shows great promise for removal of arsenic from water. In laboratory tests, it has removed more than 95% or arsenic and more than 99% of cadmium and lead. In addition, the waste material appears to be suitable for recycling or disposal in an ordinary landfill. However, the efficiency of limestone for arsenic removal could be improved. Recent research has shown that iron treatment of limestone can enhance its arsenic-removal efficiency greatly, increasing its attractiveness as an alternative to other methods.

Jan 1, 2012

By M. Hamarat

Freeport-McMoRan Copper & Gold (FCX) is committed to preserving and enhancing biodiversity in the areas in which we operate. As a member of the ICMM, FCX is committed to implement the 10 Sustainable Development (SD) Principles throughout our business. FCX is also a member of the Wildlife Habitat Council (WHC), a nonprofit coalition dedicated to protecting and enhancing wildl ife habitat. In alignment with ICMM SD Principle 7 and our Environmental Policy, FCX has set a performance goal to prepare a biodiversity inventory in 2010 and land management plan by end of 2011 for all active mining sites. In 2010 FCX established a Biodiversity Task Force to assist sites in biodiversity management; optimize use of resources around the globe; implement FCX goals and targets; and align biodiversity programs with ICMM principles and guidance. The task force consists of Environment and SD Department management, scientists and engineers from FCX sites, and WHC staff. The Task Force recently issued a biodiversity inventory guidance document to set expectations and provide consistency across the sites when developing a biodiversity inventory and land management plan.

Jan 1, 2011

By T. Patten

Inter-Mountain Labs, IML, performed a study comparing mining waste rock sample analysis by Net Carbonate Value (NCV) and Modified Sobek acid-base accounting procedures. The study looked at 468 waste rock samples and compared the data for Neutralization Potential (NP), Acid Generation Potential (AGP), Net Neutralization Potential (NNP), and the ratio of NP/AGP. The study found that a majority of the samples were below 50 Tons CaCO3/kTons. This subset of ?low-level? samples was also examined separately for Acid Base Accounting parameters. The analysis compared the NCV procedures to the Modified Sobek procedures and concludes that the NCV procedures are as protective of the environment as Modified Sobek procedures.

Feb 27, 2013

By Graham A. Davis

?The ideas of economists and political philosophers, both when they are right and when they are wrong, are more powerful than is commonly understood. Indeed, the world is ruled by little else. Practical men, who believe themselves to be quite exempt from any intellectual influences, are usually the slaves of some defunct economist. Madmen in authority, who hear voices in the air, are distilling their frenzy from some academic scribbler of a few years back. I am sure that the power of vested interests is vastly exaggerated compared with the gradual encroachment of ideas. . . . But, soon or late, it is ideas, not vested interests, which are dangerous for good or evil.? John Maynard Keynes The General Theory (1936) Policy analysts, economists and others have tradition-ally considered mining and mineral wealth a boon, providing rich countries with the resources needed to sustain their modern industrial economies while helping poorer countries generate the foreign exchange, tax revenues and other assets necessary for economic growth and development. Nevertheless, this conventional view has always had its critics.

Jan 1, 2008

By E. C. Robertson

D.G. Wilder I found the suggestion that the amount of displacement of a fault can be numerically related to the thickness of gouge or breccia to be both intuitively satisfying and intriguing. I have long agreed that there is some type of relationship between the amount of gouge and the amount of displacement of faults. I congratulate the author for developing a numerical relationship between them. However, I am concerned that the limits for applying this relationship be fully understood. An underlying assumption in this approach is that there is either a uniform thickness of gouge or breccia along a given fault or the thickness does not vary widely. Since it is not always possible to confirm this, the displacements derived by this method should be viewed with caution unless significant fault extent can be observed. At the Nevada Test Site, in drifts constructed in granite for test emplacement of spent nuclear reactor fuel, we found a fault with 0.3 to 0.4 m (12 to 16 in.) of clay gouge. Within a few meters of this location, the fault had no clay gouge, but rather consisted of a highly fractured zone with significantly altered rock and some slickensides. Based on Fig. 1, the 0.3 to 0.4 m (12 to 16 in.) thickness of gouge would indicate a displacement in excess of 30 m (98 ft). However, no gouge thickness would indicate essentially no displacement. Based on a quartz vein that terminated on the fault, and is not identified nearby, an estimated displacement of more than a few meters was made. This estimate is consistent with that obtained using the regression line proposed in the paper if the 0.3 to 0.4 m (12 to 16 in.) thickness for the gouge is used. However, using the regression curves with zero thickness would not yield results consistent with what was observed in the field. Therefore, it is important to recognize that the suggested procedure would properly yield a range of probable displacements. ? *Work performed under the auspices of the US Department of Energy by the Lawrence Livermore National Laboratory under Contract W-7405-Eng-48. Reply by E.C. Robertson It is certainly true that the t (thickness) of gg-bx (gouge and breccia) on a fault does vary along the fault. My observations have been that near the termination of a fault, the displacement d is small and the t is also small, whereas the maximum d and t will usually be found in the central part of the fault. The information on gg-bx and t of the fault found in granite in the NTS tunnel by Mr. Wilder could be interpreted somewhat differently than he does. He speaks of the fault changing within a few meters from 0.3 to 0.4 m (12 to 16 in.) of clay gg to "a highly fractured zone with significantly altered rock and some slickensides," but no gg. The highly fractured rock may be taken to be bx, rock not so finely ground as gg but still crushed by the fault movement, equivalent to the gg in my usage, and probably occupying about the same t. Mr. Wilder&apos;s estimates for the fault in the NTS tunnel for t of 0.3 to 0.4 m (12 to 16 in.) and for d of a quartz vein, in excess of "a few meters," would place the point on the low side of the central trend line in my Fig. 1, at the lower limit. There is, of course, a problem with determining d using displacement of only one planar surface. It would be greater or lesser depending on the rake of the movement. Finally, estimating the d of a fault from its t should be made with awareness of our present uncertainties, as pointed out by Mr. Wilder. Although the central trend line in my Fig. 1 has a ratio of d/t of 100, I have put the limiting ratios at 10 and 1000. Understanding of the values of the ratio will be improved only with collection of more data, for which the discussion of Mr. Wilder is much appreciated. G.C. Waterman E.C. Robertson&apos;s paper provides significant information to a geologist attempting to deduce fault offset by noting the products of structural dislocation. However, considerable mapping in underground and open-pit mines, and examination of structures produced in different geological settings, have convinced me that gouge and breccia thickness are controlled by geological conditions and fault movement. The following paragraphs suggest geological variables that control them. 1. Depth of Loading A near-surface fault resulting from tensional stress has more breccia/gouge than is produced by a similar stress at considerable depth. A deep-loaded compressional stress may produce a linear zone of schist, or structural dislocation may occur along an earlier formed belt of schist. Such "shear zones" are common in Canadian mines in precambrian rocks. In neither case can offset be directly deduced by an analysis of the minimal gouge/breccia in the shistose rocks. At greater depth, stress may be partially to wholly relieved by flowage. I vividly recall first noting the regional "Midas Thrust" in the Lark mine, Bingham Mining District, UT (where we called the structure the North Fault). My recorded notes, as I remember them, showed a narrow gouge streak separated the `Jordan" and "Commercial" limestone units from impure, muddy limestone beds of uncertain stratigraphic position. The visible structure did not indicate the great importance of this premineral fault

Jan 12, 1984

By Steve Kral

Improved metals and other commodity prices have caused the mining industry to open new mines, re-evaluate development opportunities at potential mines and increase production at existing ones. This sense of renewed optimism is being seen at operations and development projects around the world. Except in the United States. The regulatory structure there has not allowed the domestic industry to share much in mining’s resurgence. It can still take up to 10 years to permit a new mine. And, while Clinton-era regulations regarding mill sites have been put on hold, existing mines that wish to expand operations still face significant regulatory and environmental hurdles. But things may begin to improve in the United States.

Jan 1, 2005