Search Documents

By R. M. Jara

This work evaluates and characterizes the impact of the support size and mining dilution of a block model in the operation and selection of equipment at an open pit mine. An exploratory analysis and geostatistical modelling of the grades assayed on a set of drill hole samples is performed, which allows constructing a grade model on a dense grid by means of a conditional simulation. The grades are then averaged to greater selective mining unit supports in order to proceed with the study and methodology. First, the metal-tonnage curves are used to analyse the loss of selectivity on the in situ resources caused by a change of support. Concerning the ore reserves and their mining sequence, defined in the pit optimization and analysis process, the same curves prove that the loss of selectivity is more accentuated. Second, the importance of the block boundary dilution produced during mining operations is assessed. Its value depends on the amount of ore in contact with waste, on the loading error of the equipment and on the ore loss/waste dilution criterion assumed by the planner. The dilution percentage and the differences between waste and ore grades become higher when the block size decreases. For these reasons, considering the dilution in the production plans makes mining a small support more constraining. An adequate delimitation of the orebody can improve the mining selectivity, leading to greater income. Finally, a study of the increase in mining cost that provides a zero difference in NPV between the different block size options is carried out, in order to determine the maximum increase in mining costs for which it remains profitable to mine at a smaller block size. Keywords: Mining selectivity, support effect, block boundary dilution, selective mining unit size, block model.

Jan 1, 2006

By Y. He

The nature of the density distribution in a gas-solid phase fluidized bed for dry coal separation is an important factor in influencing the performance. However, during coal processing, fine slime would mix with dense medium of magnetite powder and accumulate in the bed, and its influence will affect the density of the bed. The mathematical model of the density distribution with fine slime behaviour was studied in an experimental laboratory system. The functional relationship between the density of the air dense medium fluidized bed and the coal slime content were fitted, applying the principle of least-squares method with damping factors. With the model, by analysing the trial testing data, the mechanism of the density distribution of the bed was studied and applied to a coal separation test with a pilot scale separator. Keywords: dry coal separation, gas-solid phase, model fitting.

Jan 1, 2002

By L Singheiser, W. Willenborg, M. Mueller, K. Hilpert

The limitation of fossil fuel resources and the necessity of reducing CO2emission require an increase of the efficiency of power plants by using combined cycle power systems. Pressurized Pulverized Coal Combustion (PPCC) is a potential concept to realise these objectives. The direct use of hot flue gas for driving a gas turbine requires a hot gas cleanup to achieve corrosion prevention of the turbine blading. One of the main problems is the alkali release during the coal combustion process. Molten coal ash slag has a high potential for alkali retention which depend son the alkali oxide activity in the slag. Knudsen Effusion Mass Spectrometry (KEMS) was used to determine thermodynamic data of alkali gas species over molten coal ash slags and of alkali oxides in molten coal ash slags. The main interest of the investigations focused on the structural dependence of the thermodynamic properties of the alkalis. It was found that there is a strong correlation between the thermodynamic properties and the ratio of nonbridging oxygen to tetrahedral oxygen (NBO/T). An increase of the polymerization of the slag results in a decrease of the alkali oxide activity in the slag and thus a decrease of the alkali partial pressure over the slag. Keywords: coal ash slag, structure, alkali oxide activity, alkali vapour pressure, PPCC, KEMS.

Jan 1, 2004

By N. Ogbonna

A mathematical model for bioleaching at the agglomerate scale is developed. The agglomerate is defined as a unit volume of a heap which contains a solid phase (a size distribution of ore particles), a liquid phase (stagnant and flowing leaching solution) and a gas phase (flowing air and air pockets). Leaching at the level of an ore particle is modelled using a diffusion-reaction equation, and oxidation by attached and detached microbes is treated separately. With the aid of the mathematical model, the effect of particle size distribution on the bioleaching of an ore containing a mixture of chalcocite and pyrite, and a culture of iron oxidizers, is investigated.

Jan 1, 2006

By J. Nell

An overview is given of the matte melting process used for the beneficiation of South African platinum group metal (PGM) ores. Most producers use six-electrode furnaces to melt the concentrate and Pierce Smith converters to oxidize excess iron sulphide from the furnace matte. Concentrates from two reef types (the so-called Merensky and UG-2 reefs) dominate the feedstock supply. Concentrate from the Merensky Reef is low in chromium and does not pose significant melting problems. Concentrates from the UG-2reef contain much higher levels of chromium, which results in the formation of chromium-rich spinels during melting. This is attributed to the low solubility of chromium in furnace slag under typical operating conditions (an oxygen partial pressure of 10-8?10-9bar at temperatures of 1550°C to 1600°C). During the converting process, care is needed to avoid excessively oxidizing conditions, which result in cobalt, nickel and copper losses to the slag. High nickel losses result in the formation of Fe2NiO4 (trevorite), which often forms solid solutions with FeCr2O4and Fe3O4. In future, the main challenge in the processing of South African PGM ores will be to cope with ever-increasing levels of chromium in the concentrate. A short-term solution to the problem would be to melt the concentrate under slightly reducing conditions to promote the formation of CrO, which is more soluble in the slag than Cr2O3.A longer-term solution to the problem would be to abandon the current matte-smelting process in favour of an alloy-based process, which would offer total flexibility with respect to the amount of chromium that can be tolerated in the feed. Keywords: Merensky, UG-2, furnace, slag, matte, converting, spinel, chromium

Jan 1, 2004

By F. T. Cawood

The definition of mineral rents has historically been somewhat unclear, but a growing understanding of the source and composition of the revenues that comprise these rents mean that they can be more easily identified and quantified. Furthermore the way in which the flow of the rents from mineral developments are captured and then distributed has been a point of contention amongst the various stakeholders. Investors, the host government, the resource owners, environmental interests, indigenous groups and land owners are identified in this paper as the principal participants in mineral development and while each is entitled to a portion of the rent, the size of their portions will differ. A competitive rent-sharing model for southern African countries has been established and indicates how the range of stakeholders could be rewarded for their contribution. Acceptance of the sharing ratios amongst the recipients is a function of their understanding of the size of the rent and their position in the hierarchy of stakeholders. At first glance investors appear to receive the largest share of the rent, but they disburse some of the rent to hidden costs, which when all is said and done, means that investors and host governments retain approximately equal shares of the mineral rent. Both the investor and government are faced with the dilemma of how to equitably distribute the rents they have captured to minority stakeholders. Government captures corporate tax, mineral royalties and a wide range of subordinate taxes, but is required to construct policies that will ensure distributional equity among the various levels of government as well as among the provinces that comprise the country. Investors will have to ensure that a portion of the rents they capture are diverted to other stakeholders namely resource owners, environmental interests, indigenous peoples groups and the landowners. This paper identifies the major recipients of rent and provides some indication of equitable distribution ratios for mineral wealth among them?a first step in ensuring that mineral development is compatible with long-term sustainable development and in the best national interests.

Jan 1, 2002

The environmental impact of solid waste materials is closely linked to their potential to produce a hazardous leachate once deposited in a landfill. This potential is conventionally assessed with simple laboratory batch leach tests, which find more and more frequent application also in the minerals and metals industry. Such tests are intended to help distinguish between high and low risk wastes, but are completely unsuitable to allow quantitative prediction or modelling of the long-term leachate generation potential. In the present approach the leachate generation process is perceived as a combination of bulk convective transport, stagnant zone and inner particle diffusion, as well as reaction kinetic effects. Model equations are formulated accordingly. A modelling frame work, WASTESIM, has been developed at UCT, which allows flexible combination of the model components and simulation of leach scenarios. Quantitative model parameters are obtained from a systematic laboratory study on the waste material in question. The combined assessment and modelling approach is demonstrated with a study on Cr (VI) leaching from a ferro-chromium slag material. Although not straightforward, the approach is particularly useful in determining long-term liabilities in the context of waste disposal sites with considerably more reliability than has previously been possible. Keywords: waste deposits, waste leaching, heap leaching, environmental, risk assessment, Cr (VI), ferro-chromium, slag.

Jan 1, 2000

By H. Saroglou

The anisotropic behaviour of Athens Schist has been brought out through the testing of specimens with varying orientation of schistosity with respect to the major principal stress under uniaxial, triaxial and dynamic conditions. A large number of results from tests on intact rock specimens of the Athens Schist were statistically analysed and evaluated.

Jan 1, 2004

Electricity supply constraints in SA are increasingly challenging mines to operate more energy efficiently without reducing production output. Mining compressed air systems are well known to be operated inefficiently and are also a major power consumer. Two available and proven technologies can be applied on new and existing mines to replace or and optimise available compressed air facilities and achieve meaningful reductions in electrical power consumption; ? Hydro powered drilling and mining is significantly more energy efficient than compressed air and provides drilling rates that are twice as fast. ? Stope drilling systems using compressed-air or water drills allow further energy savings. The technologies are discussed and a broad strategy to selectively apply these them together is presented.

Jan 1, 2008

By M. Moys

The use of temperature measurements for unusual applications in the analysis and control of column flotation and milling is discussed. This is followed by a review of some of the authors current research in the application of the discrete element method to the modelling of particulate processes, specifically milling, fluidized beds and chute flow.

Jan 1, 2005

After the closure of collieries, they naturally start to fill up with water. As a result, hydraulic gradients develop between them and different hydraulic pressures are exerted onto peripheral areas or compartments within mines. This results in water flow between mines, or onto the surface. This flow is referred to as intermine flow. The collieries in the Witbank Coalfield have geometries such that there are several areas where this intermine flow is possible. Since the Department of Water Affairs and Forestry has declared intermine flow as one of its greatest concerns for granting closure to South African mines, much research into this phenomenon is required. The challenges in determining intermine flow are numerous, and attention has focused on identification of areas where these flows can take place. The quantification of these flows is problematic due to the uncertainties in exact geometric configurations and the variation in site-specific hydraulic properties of thecoal and overlying lithilogical layers. During this study, use has been made of numerical flow modelling and several analytic solutions to test the applicability of the flow models as well as to predict groundwater flow directions, filling times of voids and flow volumes. The numerical modelling methodology entailed a downscaling approach starting with a broad regional model covering the entire area, followed by modelling the interactions between interconnected mines, and finally looking in detail at the major areas of interaction.

Jan 1, 2005

By P. W. van Deventer

?Soil quality is the capacity of a soil to function, within ecosystem and land use boundaries, to sustain biological productivity, maintain environmental quality, and promote plant, animal and human health?. In the long-term, vegetative rehabilitation of mining wastes aims at, as far as possible, the proper ecological integration of the reclaimed area into the surrounding landscape, which is sustainable and requires minimal maintenance. A certain succession pattern is therefore needed. Recent ecological concepts recognize the role of the substrate?s quality and nutrients in affecting the rates and directions of succession patterns. Although pedogenesis and eventually soil quality in mine waste are not well known, monitoring of soil quality parameters in kimberlite mine tailings reveal a remarkable establishment and or improvement of specifics oil quality indicators. During the same time the vegetative cover?s total functionality as well as reproductive ability improved. Functions of soil, and thus soil quality, can be assessed at the field, farm, ecosystem, pedosphere, and global scale. It is recognized, however, that management of soil becomes increasingly difficult at larger scales, but for demarcated mine waste sites it is possible to ameliorate and manage and assess soil functions and quality. Therefore the significance of the study is the following: soil functions and quality become inseparable from the idea of system sustainability, and are considered as key indicators of ecosystem sustainability on rehabilitated mine tailings material.

Jan 1, 2008

By J. G. Bruwer

Paper written on project work carried out in partial fulfilment of B Eng Met Surface coatings persisting on zircon particles, after being leached in an acidic solution, are believed to be the cause of zircon misplacement during the electrostatic separation of heavy mineral beach sands. Electrostatic separation is employed to separate non-conductive zircon particles from more conductive rutile particles. Surface coatings on zircon particles are believed to render the non-conductive zircon particles more conductive, resulting in the contamination of the more conductive rutile stream with zircon particles. Resistivity measurements, X-ray photoelectron spectroscopy (XPS) and scanning electron microscopy (SEM) were performed to compare the surface characteristics of zircon particles found in the different product streams following electrostatic separation. XPS analysis showed that no significant difference exists in the outermost layer of the zircon particles found in the different streams. SEM analysis showed the existing surface coatings on zircon particles from different product streams to have similar chemical compositions. Resistivity measurements confirmed the results obtained from both the XPS and SEM analysis; no significant differences in the resitivities were observed. From the results obtained it suggests that surface coatings present on zircon particles are unlikely the primary cause of zircon misplacement. Zircon losses can possibly be a result of machine related aspects. Key words: XPS; SEM; resistivity measurements; electrostatic separation; heavy mineral sands.

Jan 1, 2007

By P. J. Foster

A common theme running through recently introduced mining health and safety legislation in many parts of the world is risk assessment. Most recently, risk assessment legislation has been introduced across the mining industry of South Africa and the view that the introduction of risk assessment based legislation provides an ideal opportunity to improve on past health and safety performance is presented. Risk assessment techniques range from highly complex safety system techniques that are used in high technology process industries, to subjective techniques based on simple judgements that are finding use in many other industries. The objective of this paper is to shed some light on risk assessment, not by detailing the risk assessment process but by identifying the crucial elements that need to be considered if risk assessments are to be successful in changing health and safety performance. A case study is presented illustrating the introduction of risk assessment into the Ingwe Coal Corporation, one of South Africa?s largest mining houses, to indicate how the system was developed and how it is being used.

Jan 1, 1998

This paper reviews ore pass practice in some Canadian mines in Quebec and Ontario. In particular it reviews ore pass configuration, flow control mechanisms and monitoring practice. A review of the type of problems encountered and the tools to restore flow is also presented.

Jan 1, 2005

By L Tolmay, L Nair

Investor confidence can be compromised when one observes large discrepancies between the SAMREC reserves and the mining plan. It is therefore up to the responsible persons to ensure that all contributing factors get taken into account when determining a reserve declaration. Confounding factors could be further aggravated by large oscillations in the commodity price thus resulting in major changes to the mining plan, if the accepted price was either too optimistic or pessimistic. Additional factors that must receive our attention are, uncertainty in geological facies type, mining practices, geology and grade estimation. The paper outlines (in the authors? opinion) some of the important factors that need to be taken into account, in order to ensure proper alignment between the estimates of the life of mine (LOM) reserve grades, and the corresponding actualisation of the mining plan. These parameters provide an historical insight into what actually happens when attempts are made to implement the mining envisaged in the LOM plan. In turn these allow judicious application of discount factors that enable a realistic estimate of SAMREC reserve classification and declaration. Some of the factors that will be covered are: - 1) Flexibility of developed reserves and the ability to maintain this. 2) Mining control mechanisms and their overall efficacy. 3) The ability to extrapolate facies types and its effect on grade control. 4) The ability to control the mining mix and value variation. 5) Finding a happy medium between optimism and pragmatism.

Jan 1, 2007

By U. Sachse

This paper explores a systematic approach for mining decision-makers to use when faced with choosing which method to use for a specific rockpass length. The different excavation methods available in the broad South African mining industry are compared against a number of critical parameters, as applied to rockpasses of varying length. This approach is not meant as a definitive, prescriptive planning tool, but rather as a proposed approach to enable designers and planners to choose the best system to excavate their specific rockpasses

Jan 1, 2005

The paper deals with the results of dynamic tests carried out on a range of surface support liners consisting of combinations of mesh (various types), shotcrete, and wire rope lacing. The testing was carried out over the period 1993 to 1998. The dynamic testing method made use of drop weight impact loading of test samples which attempted to simulate realistic in situ conditions, and the range of loading imposed was equivalent to small to severe rockburst conditions. The results of the testing provide quantitative data, in the form of input energy, which is relevant for support design and for the choice of support types appropriate for situations in which significant mine-induced seismicity occurs or is expected to occur. In addition to the wire mesh and shotcrete liner systems tested, estimates of energy capacity are made for other, untested, systems.

Jan 1, 2001

By H. Saroglou

Anisotropy is a characteristic of intact foliated metamorphic rocks (slates, gneisses, phyllites, schists). Testing was used to establish the anisotropic behaviour of selected gneissic rocks. The effect of anisotropy on various mechanical properties (strength, deformation) and dynamic properties (wave velocity) was examined. The rock samples were also tested at successively higher confining pressures in order to evaluate the effect of anisotropic behaviour at high overburden pressures.

Jan 1, 2004

By I. K. Craig, F. R. Camisani-Calzolari

Defects which occur at the surface of a continuously cast slab impede the throughput of final product, because an extra stage in the process is required to grind the defects away before further processing can take place. Defect prediction and the minimization of the occurrence of defects is required. The use of two models to define the defect propagation is explained. Both models are derived using system identification techniques such as auto-regression with exogenous input(ARX). One model is used to determine the effect of manipulated variables such as casting speed and measured disturbances such as mould level on temperatures within the mould. The other isused to determine or indicate the effect of the mould temperatures on the occurrence of defects such as transversal cracks. The latter model can be used to predict when the defects will occur and the former can be used to control the occurrence of the defects. Keywords: continuous casting, surface defect, control system, predictor, system identification, ARX

Jan 1, 2003