Search Documents

By R. Tabanrad

This article examines the stability analysis of intake tunnels of Karun III dam & power plant. The tunnels have been excavated with a 3-dimensional and fairly complicated geometry in Pabdeh weak formation rocks at Zagros region. Due to the particular excavation geometry and inapplicability of plane-strain status, the stability of these excavations has been analyzed using both the 3D elastic software Examine 3D and the 2D non-elastic software UDEC simultaneously. The geomechanical parameters have been estimated by back analyzing the measured displacements from instruments, which were installed in the tunnels, and the parameters have been used in non-elastic numerical model. The results of the analysis show that the strains occurred in surrounding rock mass are less than the allowable failure strain and that the tunnels are stable. In addition, considering the results of non-elastic 2D analysis, the areas with unstable potentiality were identified and after the instability occurred at the areas predicted by the model , it was stopped up to the allowable strain limit through installing additional support . Bei diesem Artikel handelt es sich um eine Analyse der Festigkeit der Eingangstunnel des Damms und Elektrizitätswerks “Karoon III”.Die Tunnel haben drei Dimensionen und eine sehr schwierige Form und sind in brüchigen Felsen in “Pabedeh ,in Zagrossgebirge”eingebohrt.Aufgrund besonderer Form der Bohrung wurde ihre Festigkeit durch elastische dreidimensionale Soft-ware analysiert,die gleichzeitig die drei-und zweidimensionale unelastische Soft-ware UDEC benutzt hat.Die geometrische Parameter sind mit Ausnützung der Analyse berechneter eingesetzter Versorgungen,die in Tunnel aufgebaut sind,bewertet.Und diese Parameter sind in Zahlen-Analyse benutzt.Die Ergebnisse dieser Analyse zeigen,dass die Drücke an Felsen weniger als problematischer Grad der Drücke sind und die Tunnel fest sind.Ausserdem wurde mit einem Einblick auf die Ergebnisse der unelastischen zweidimensionale Analyse die eventuellen unfesten Teile bestimmt.Nach entstandener Unfestigkeit an diesen Teilen wurde die problematischeDrücke für Aufbau mehrere Anlagen gestoppt. Cet article examine l'analyse de la stabilité de tunnels de la prise de Karoun barrage III et centrale électrique. Les tunnels ont été excavés avec une 3 dimensionnel et compliqué géométrie dans Pabedeh que la formation faible balance à région Zagros équitablement. Dû à la géométrie de l'excavation particulière et inapplicabilite de statut de tension plane, la stabilité de ces excavations a été analysée en utilisant les deux le 3D logiciel élastique Examen 3D et le 2D logiciel non - élastique UDEC simultanément. Les paramètres du geomechanical ont été estimés en analysant le déplacement mesuré d'instruments qui ont été installés dans les tunnels et les paramètres en arrière a été utilisé dans les modèles numériques non - élastique. Les résultats de l'analyse montrent que les tensions se sont produites dans masse du roc environnante est plus petit que la tension de l'échec admissible et que les tunnels sont stables. De plus, les régions avec potentialité instable ont été identifiées étant donné les résultats de 2D analyse non - élastique, et après que l'instabilité se soit produite aux régions prédites par le modèle, il a été arrêté jusqu'à la limite de la tension admissible à travers installer du support supplémentaire.

Jan 1, 2003

By F. S. A. de Frey, F. C. Kruger

Personnel management has undergone a remarkable change over the course of the past ten years. Personnel departments have played an increasingly important role, which today requires highly trained people and cannot be adequately served by the lesser qualified officials of yesteryear. Changes in the mining industry that stem from the demand for skilled labour to keep pace with technological developments and the mechanization of mines today demand that emphasis should be placed on the maximum utilization of manpower. Maximum utilization of manpower calls for more scientific and effective methods of recruiting, selecting, training, and placing workers so as to offer them the best opportunities for development and promotion, which naturally ensure a minimum labour turnover and eliminate labour unrest. This can be achieved only if well-qualified and properly trained personnel administrators are prepared to accept the challenge and apply themselves purposefully by assisting line mangement with the attainment of the company's corporate objectives.

Jan 1, 1982

By E. J. Magri

This paper describes a geostatistical study of the relative merits of diamond-saw sampling and conventional chip sampling, using results from experimental work carried out on Randfontein Estates Gold Mine and Western Areas Gold Mine. The diamond-saw sampling procedure is described, and it is concluded that this is a very efficient operation and leads to good-quality sampling that is clearly an improvement over conventional chip sampling. The study principally involved the computation of the errors of estimation of the mea gold value of mining panels for the two sampling methods, revealing that, in the normal production environment, the diamond-saw sampling method is a significant improvement over conventional chip sampling, as evidenced by the reduced estimation errors achieved. The question of optimum sample spacing is discussed, and it is concluded that the required spacing for chip sampling needs to be smaller than for the diamond-saw method.

Jan 1, 1986

By A. P. I. Popoola

Aluminium AA1200 was laser alloyed with a combination of nickel and titanium diboride using different weight ratios. Chemical reactions took place with the formation of different phases. The characterization of the alloyed surfaces was carried out by x-ray diffraction (XRD), optical and scanning electron microscopes. The alloyed surfaces are composed of the initial phase of Al-Ni dendrites and eutectics of TiB2/Al and TiB2/Ni distributed on the initial phase. Experimental results obtained showed that Al-Ni intermetallics brought about a significant increase in the hardness property of Al; however, these intermetallics are highly brittle and prone to fail by brittle fracture or stress corrosion cracking when put in service. The addition of TiB2 brought about a reduction in the formation of the seintermetallic phases. A microhardness increase of over 10 times the hardness of the substrate was achieved. Keywords Dendrites, intermetallics, metal composite, Nd: YAG laser.

Jan 1, 2011

By Paul Fouchè, Danie van der Merwe

Contents ?Purpose ?Introduction ?Development of RF tracers ?Test procedure ?Results ?Conclusion ?Way forward ?Acknowledgements

Jan 1, 2005

By M. U. Ozbay

The stability of pillars is analysed on the assumption that pillars shed load in a stable manner if the slope the strata load-deformation relation is steeper than that of pillars in the post-peak regime. Concepts of local stiffness, mine structural stiffness, and critical stiffness are discussed. Procedures are described for the determination of strata stiffness for various pillar layouts by use of the available boundary-element computer programs. The postpeak stiffness of pillars is assessed from the available data relating to the post-peak load-deformation relationship and width-to-height ratio. Stability analyses are carried out by the contrasting of strata stiffness with post-peak pillar stiffness. It is shown that the strata stiffness becomes unacceptably small for a stable yield-pillar layout when the span exceeds about 5 times the depth. The strata stiffness is found to increase, thereby increasing the stability, as the span-to-depth ratio, number of pillars, and percentage extraction are decreased. It is also found that the stability in a yield pillar becomes difficult to achieve when al the pillars in a layout are in the descending part their post-peak load-deformation curve

Jan 1, 1989

By R. Falcon, A. J. Ham

This paper summarizes the characteristics of Southern African coals, presents a fundamental approach to the combustion performance of coal, and reviews some of the recent developments in the fields of technological evaluation and boiler design for coals typical of this region. This includes a summary of the petrographic constituents of coa~ highlighting the differences between the Palaeozoic coals of the northern and southern hemispheres (Laurasia and Gondwana respectively), and the effects of these properties on the combustion performance of coal as seen in terms of laboratory, pilot-scale, and full-scale operating conditions. Recent developments in boiler design linked to advanced characterization studies and commercial experience have led to unprecedented use, with maximum effect, of the low-grade, high-ash, high-inertinite coals typical of some parts of this region. In the light of this success, more adequate understanding and better methods of assessment of the coals typical of the Gondwana region are called for, particularly in the light of the price premium for high-grade coal and the more cost-effective lower grade coals on the international steam markets.

Jan 1, 1988

By C. S. Erasmus, L. C. Woollacott

The distribution of gold loaded onto carbon particles from a carbon-in-pulp operation was measured by neutron activation analysis. The nature of the distribution is examined, and the implications for operating plants and CIP simulators are discussed.

Jan 1, 1992

By R. P. King

The ideas leading to the formulation and utilization of a flotation model are developed. The main theoretical and experimental work that has been carried out by the National Institute for Metallurgy Research Group at the University of Natal is presented. The two experimental flotation plants available to this Group are described.

By H. Knorre, A. Griffiths, R. Higgins, S. Gos

Hydrogen peroxide is gaining acceptance as a reagent for the treatment of mining effluents containing cyanide. In this paper some of the chemical and environmental aspects of treatment with hydrogen peroxide are discussed, and one way of improving the economics of the process is described. This is known as selective detoxification, which involves the oxidation of the less stable (cyanide) complexes while not affecting the more stable complexes, which contribute very little to the concentration of free cyanide or to the toxicity of the treated water.

Jan 1, 1987

The relationships between backfill-transportation parameters (solids concentration, velocity, and pipe diameter) and the wear rate of backfill-transportation pipelines is well understood. However, the degree of wear experienced by a pipeline depends not only on the transportation parameters, but also on the characteristics of the solids making up the backfill, i.e. the particle-size distribution, hardness, shape, and sharpness of the particles. Therefore, unless data corresponding to the specific wear rate of the solids are available, the determination of the wear rate for pipes transporting an uncharacterized backfill is largely guesswork. This paper describes an evaluation of particle characteristics with special reference to particle sharpness so that pipe wear rates can be correlated with solids of different size distributions and sharpnesses.

Jan 1, 1993

By H. D. Mtegha

The Southern African Development Community (SADC) aims to harmonize mineral policies and regulatory regimes in the minerals sector. This paper provides a review of the progress made towards harmonization of mineral regimes in the region. It singles out only the mining fiscal environment, as this is normally one of the key issues of interest to potential investors as well as the host state. Indications are that the region is slowly progressing towards a more harmonized approach, and there is evidence that the ?race to the bottom? has been prevented, which is the basis for an integrated mineral sector that the region aspires to.

Jan 1, 2011

By S. O. Choi, H. -S. Shin, W. -K. Song

Nuclear waste should be disposed with the best warranty for the national health and welfare. Among the several repository systems, the deep underground disposal is considered to be a most suitable system in Korean peninsula. However it demands basically the comprehensive stability analysis such as the behaviour of discontinuities in rock mass, the behaviour of ground water, and the reaction of rock stress according to the heat from the nuclear waste. For these purposes, the underground nuclear waste disposal repository was simulated in two- and three- dimensions. It shows that emphasis will be given to the thermal conductivity of discontinuities and the thermal convection of ground water as well as the thermal stress generated by the nuclear waste for design and construction of repository system, and they should be obtained from the field measurements. Déchets nucléaires devront tre déposés avec la meilleure garantie pour la santé et le bien public. Parmi les plusieurs systèmes de dépôt, la disposition en souterrin profond est considérée au système le plus approprié en Corée. Pourtant ce système demande essentiellement l’analyse éten-due de stabilité comme le comportement des discontinues en masse rocheuse, le comportement de l’eau souterrin et la réaction des contraintes de roche selon la chaleur depuis les déchets nucléaires. Pour ce but, le dépôt des déchets nucléaires en sous-sol a étè simulé en deux et trois dimensions. Il montre que l’accent sera donné à la conductivité thermale des discontinues et la convection thermale de l’eau souterrin aussi bien que la contrainte thermale générée par les déchets nucléaires pour le plan et la construction du systèmes de dépôt, et ils devront tre obtenus depuis les mesures sur place. Die Kernwüste muß mit der besten Gewähr für die nationale Gesundheit und die Wohlfahrt angeordnenet werden. Unter einigem Fundgrubesystem, das tief unterirdisch Wegwerfen werde in Betracht das passendest System in der koreanisch Halbinsel gezogen. Jedoch, es verlangt grundzätzlich die umfassend Stabilitätsberechnung so wie das Behnehmen mangelnder Konti-nuität in der Felsmasse, das Behnehmen des Grundwasser, und die Reaktion der Felsenbelastung nach der Hitze von der Kernwüste. Für diesen Zwecke, die unterirdische Wegferfenfundgrube der Kernwüste wurde in der zwei und drei Dimensionen gesimuliert. Es beweist daß die Betonung wird zur thermisch Leitfähigkeit mangelnder Kontinuität und thermisch Konvektion des Grund-wasser sowie die thermisch Belastung ergezeugt durch die Kernwüste für den Entwurf und die Konstruktion des Fundgrubesystem gegeben werden, und sie müssen von den Feldmaße ergelangt werden .

Jan 1, 2003

By D. Harbottle, D. Rhodes, T. F. Jones, S. R. Biggs

Multiphase process design and optimization often depends upon the rheological properties of sludges and slurries. In practice the task of determining these important properties is usually carried out by removing small samples from a process line or process unit and performing tests with proprietary bench-top analysers near to site or at a remote laboratory. Sampling will remain an important procedure in industrial processes, but there is also a strong case for augmenting the routine information obtained using an in situ sensor, as suggested below. ?Sampling protocols can result in extensive turnaround periods from sample collection to the generation of results. The delay can have an effect on a variety of factors such as product quality, process operability and efficiency. ?Sampling of toxic or radioactive material can prove an even greater challenge to minimize human involvement. ?Removal often changes the rheology of a specimen, and might lead to incorrect conclusions being drawn about the condition of a sludge. ?Sludge and slurry in a containment suffers a gravitational gradient, so that a removed sample should be paired with its location, particularly in the vertical dimension.

Jan 1, 2007

By I. J. Barker

This paper argues that the scale up of furnaces and the supply of electricity are going to be two major issues that will affect the ferro-alloy industry in the near future, and that economic factors will drive this development. The most common type of furnace for producing ferroalloys at present is the submerged-arc furnace with three electrodes, fed from a three-phase AC electrical supply. The scale up of this technology has now reached a fundamental constraint, which is caused by the electrical reactance of the secondary circuit. If the economy of any further scale up is to be achieved in the future then a different technology will have to be used. The supply of electrical power in future is likely to become amore complex issue than it is at present. Existing submerged-arc furnaces tend to run at fairly steady loads, but the ability to swing the load under demand-side management may offer advantages, and may allow a furnace to obtain cheaper power from the organizations that supply this power. This will have to be counterbalanced against the nuisance factors incurred by having a varying load in the operation of the furnace. Various options are therefore discussed in this paper. The possibility of scale up of Søderberg electrodes is discussed, as well as the use of DC power and multiple electrodes. Some of the issues with load swinging are also examined. A particular scenario is also briefly presented to show that considerable further scale up of ferro-alloy furnaces is still possible.

Jan 1, 2011

By A. Nicotra, E. H. Roux, J. H. du Plooy, D. H. de Jagger, P. De Waal, G. J. van der Linde

This paper reviews the geology, history, current beneficiation practices, uses, marketing, and future outlook of phosphate in South Africa. The vastness of the reserves, and the industry's efficiency and competitiveness in world terms, are highlighted.

Jan 1, 1989

By R. J. Davidson

The mechanism of gold adsorption on activated charcoal by R. J. DAVIDSON: M.Se., Ph.D. (Rhodes) (Visitor) The adsorption of gold onto activated charcoal is most dependent on the concentration and character of the 'spectator' cations present in the adsorption medium. In the presence of calcium ions, gold is adsorbed as the calcium aurocyanide complex. The degree to which the aurocyanide complexes are adsorbed follows the series Ca> Mt:> H> Li> Na> K, calcium aurocyanide being the most stable complex and potassium aurocyanide the least firmly bound. If a loaded charcoal, where the gold is present as the calcium complex, is treated initially with either sodium carbonate or potassium carbonate solutions, the gold can subsequently be eluted from the charcoal with hot deionized water as either the sodium or the potassium complex respectively. The elution of gold with deionized water appears to be most attractive practically and economically, and has several potential applications in the recovery of gold from dilute solutions.

Jan 10, 1974

By W. Wittke, D. Schröder, H. Polczyk

ABSTRACT: The Urft dam, the Diemel dam and the Eder dam are three old masonry damslocated in Germany. The paper describes the rehabilitation measures and the correspondingstability analyses carried out to adjust the dams to today's standards. Remedial works such as theexcavation of inspection galleries, the installation of a grout curtain with a downstream drainagescreen as well as the installation of pre-stressed permanent tendons were carried out. In all threecases the stability of the upgraded dam could be proven on the basis of finite element analyses. ZUSAMMENFASSUNG: Die Urft-, Diemel- und Edertalsperre sind drei alte deutscheSchwergewichtsmauern aus Bruchsteinmauerwerk. Im Beitrag werden Instandsetzungsmaß-nahmen und Standsicherheitsnachweise beschrieben, die erforderlich waren, um die Staumauernan den heutigen Stand der Technik anzupassen. Hierzu wurden Kontrollgänge aufgefahren,Dichtungsschleier mit luftseitiger Dränage sowie vorgespannte Daueranker hergestellt. In allendrei Fällen konnte unter Berücksichtigung der Instandsetzungsmaßnahmen die Standsicherheit derMauer auf der Grundlage von Berechnungen nach der Methode der finiten Elemente nachgewiesenwerden. RÉSUMÉ: Les barrages de Urft, Diemel et Eder sont trois barrages-poids vieux allemandsconstruit de maçonnerie de moellon. Dans cet article, opérations de remise en état et preuves destabilité sont décrits, qui étaient nécessaires pour adapter les barrages à l'état de la techniqueactuelle. À cet effet, des galeries de contrôle étaient creusés, voiles d'étanchéité avec des drains àla face aval et tirants précontraints permanents étaient fabriqués. Dans tous les trois cas, tenantcompte des opérations de remise en état, la stabilité de la barrage pouvait être prouvée à partir decalculs selon la méthode des éléments finis.

Jan 1, 2003

If the Journal is to fulfill its mandate to the mining and metallurgical industry, it needs to expand its readership and, by implication, membership of The South African Institute of Mining and Metallurgy. This we hope to do by increasing the appeal of the Journal to a wider audience through the inclusion, in addition to our high-quality research papers, of equally high-quality papers, articles, and contributions that will be of interest to our less research-minded members.

Jan 1, 1990

By N. Graham, C. Walker

The SORD Miner is a patented mining principle being developed to exploit mineral and energy resources that current technology can not access. SORD Miner is designed to operate in underground wet, granular, continuously collapsing geological environments such as alluvial and marine deposits. It is somewhat like a cutter suction dredge and should be capable of mining its way through any fine granular material like sand or gravel, pumping the slurry back to the surface. In areas where the target layer is covered, the SORD Miner is inserted below the water table and will tunnel its way to the mineral deposits at depth. This paper describes the development, concept testing and prototype construction of the SORD Miner.

Jan 1, 2007