Search Documents

By M. Nicolle

The Tati Activox® Project will be the first full-scale implementation of the patented Activox® process (The Tati Activox® project was deferred in 2008. Please refer to the Norilsk Nickel press issue on the topic for more info). The process was developed by Norilsk Process Technology and has been tested on Tati mine sulphide concentrates in laboratory, pilot and demonstration plant scales and demonstrated its viability. There are inherent risks to the final scale-up of the process from the demo plant and one of them will be investigated in this paper. Compartment 1 is designed to leach approximately 77% of the total nickel leached. For this reason agitation requirements in the first compartment of the autoclave are reviewed. An attempt is made to minimize the process and mechanical risks associated in achieving oxygen mass transfer into the slurry solution. The agitator powers for oxygen mass transfer are calculated using empirical correlations and compared to demonstration plant testwork. The resulting gassed power per unit volume (P/V) is higher than most commercial autoclaves and raises uncertainty on the viability of using such high unit power inputs. Additionally, there is concern about the ability of the autoclave shell to withstand and support the higher loading of large agitators. An alternative solution to designing for the increased P/V is assessed in which the number of compartments within the autoclave is reduced from 5 to 4 by removing the compartment wall separating compartments 1 and 2. This results in an enlarged first compartment containing 3 agitators instead of 2. Therefore the compartment 1 oxygen demand is supplied through 3 agitators, which lowers the P/V per agitator. The reduction in the number of autoclave compartments raises the potential for short-circuiting the mean flow pattern by slurry particles. Short-circuiting and low velocity zones could result in a lower recovery of metal and localized hot spots, respectively. A computational fluid dynamic (CFD) analysis was conducted to quantify these concerns and also to evaluate further design considerations. The results indicate that the proposed design change to 4 compartments affects short-circuiting. The impact of increased short-circuiting on the overall autoclave recoveries is not quantified, however; it is expected to be negligible based on testwork done in the Tati Demonstration Plant and similar modifications made to another operating autoclave. The CFD analysis also suggests that there will be no low velocity zones within the compartment.

Jan 1, 2009

The case for national research in mineral processing PRESIDENTIAL ADDRESS given by R. E. Robinson*, Ph.D., B.Sc. (Eng.) (Wits.) Some of you have only raised your eyebrows, some have made tactful comments, and a few of you have been fairly outspoken, but all of you in industry are concerned at the high level of State expenditure by bodies such as the National Institute for Metallurgy. The case for a national research organization in mineral processing is not clear-cut and in fairness I must present both cases - for and against. Competition for student members Each year the South African Institute of Mining and Metallurgy offers a prize (or prizes should the entries warrant it) of up to Rl00 for the best paper or dissertation on a topic appropriate to the interests of the Institute.

Jan 10, 1975

By O. Bazhko

Regular analysis of different streams is important for the control of hydrometallurgical processes. Various physical and physical-chemical methods are applied for this purpose. Many modern methods require costly equipment and are subject to interferences. Therefore, redoxtitration methods remain of interest. The use of different types of oxidizing and reducing agents as well as redox indicators enables many cations and anions to be rapidly and accurately analysed. Sometimes redox titrations require the prior preparation and addition of masking agents. Selective, sensitive and low-cost methods of redoxtitration of copper and SO2 in plant conditions are described.

Jan 1, 2009

By E. A. Brinkmann

A kinetic model framework for single particle kinetics in combined diffusion and adsorption processes is presented. The framework applies to the general case in which both diffusion and the adsorption reaction play important roles in determining the overall rate in processes where the migrating species can both adsorb and accumulate. The technique, which should be applicable to a wide range of reaction mechanisms, consists of an iterative integration procedure for the coupled diffusion and reaction equations. The case of a reversible linear adsorption reaction rate is developed. In order to verify the technique as a legitimate method of model development, an analytical solution for the identical case is derived and compared to the numerical solution. Excellent agreement exists between the two solutions.

Jan 1, 1987

By S. K. Murphy

A partial shaft pillar extraction project was embarked on at a mine in the West Wits mining region in South Africa. Prior to the extraction, a rock engineering assessment was conducted with the main objective being to establish which areas of the shaft pillar could be extracted without unduly affecting the stability of major infrastructure within the shaft pillar. Standard numerical modelling methods were used to conduct this assessment and several areas were identified for extraction. However, during the extraction process, it was found that the infrastructure was affected more than was originally predicted by linear elastic modelling. In addition to this, several large events resulted in far more large aftershocks than would normally be predicted. In order to gain an understanding of this phenomenon, seismic data was integrated with numerical modelling as follows: > The seismic data in the form of displacements was integrated in 3D space within the model to assess the effect of static stress changes associated with seismic activity > Data from large events was integrated onto specific structures, where displacements associated with large events were integrated onto the plane of structure in question. This paper describes the methodology and results obtained from each of the above processes and include insights into the mining process that were previously unfathomable using standard linear elastic numerical modelling. The way forward for this rock engineering assessment of partial shaft pillar extraction is also discussed.

Jan 1, 2012

By N. G. Cook, N. C. Joughin, A. J. A. White

The rate of face advance in the gold mines is between 3 and 10 m a month, with a median value of about 5 m a month; it follows that faces are blasted less frequently than is planned. There are many advantages in the use of short holes for stoping to give face advances of from 0,7 to 0,8 m per blast. This has the potential for so increasing the frequency of blasting that monthly rates of face advance could be improved significantly. Cleaning with face scrapers is too slow to permit the maximum achievement of a complete clean, drill, and blast cycle for each shift. Short-hole blasting, combined with the use of mechanical conveyors for face cleaning, offers the possibility of completing two such cycles each day, yielding monthly rates of face advance of up to 35 m. Experiments aimed at developing safe, unitized explosive charges well-suited to produce reliable face advances of 0,7 to 0,8 m per blast under a wide range of gold-mining conditions have been notably successful. A novel method of assessing the effectiveness of a blast based on the percentage of holes that leave socket lengths of 5 cm or less was used. Unitized charges of 60 per cent Ammon gelignite, 600 mm long by 25 mm in diameter, appear to be near optimal. The explosive is de-sensitized to obviate detonation by chance mechanical impact, but requires only a 6D detonator for initiation; it has good water-resistance. Means have been developed for producing these cartridges automatically, but the necessary machines will have to be built specially and the cartridges are not yet available in large numbers. A second experiment by way of an extended pilot production trial using these cartridges in holes 0,9 m long is now under way. Preliminary results indicate that drilling and explosive efficiencies and productivity are well above average, even though face scraping is being used. Unitized charges of this type are likely to prove even more advantageous when mechanical face conveyors come into use.

Jan 1, 1975

By D. A. J. Ross-Watt

Right now the South African mining industry is a high-profile, vital contributor to the nation just as it has been for the past one hundred and twenty-six years since the discovery of diamonds-perhaps even further back if the mining of copper, iron ore, tin, and other minerals in earlier centuries is included. The media in 1995, as has been the case over the years, bear testimony to the complex interactions between the industry and its stakeholders: shareholders, government, employees and their unions, training and educational institutions, researchers, markets, the public, and suppliers of goods, services, and infrastructure. The pressures and challenges that the industry continues to face can be summarized as safety and health, competitiveness, and social and environmental responsibility. There are no surprises here. The motivation for the industry to perform well in these areas is clear; the focus I intend to bring is on the most important tool required for success-that of good mining engineering. This Address sets out - to review the mining aspects that have been discussed in South Africa during the first five years of the decade, a discussion that shows the return of the country as an important mining forum, confirms the role of professional institutes and associations in the development of mining engineering, and brings current relevant issues into focus - to highlight the vital role of mining engineering in the industry, and to identify priorities for the remainder of the decade - to provide the prospective mining engineer, the mining-engineering student and trainee, and the practising mining engineer and mine manager with a better appreciation of the mining-engineering discipline. institutes and ssociations

Jan 1, 1995

By S. K. Kawatra

Feasibility studies of the on-stream analysis of lead in mineral slurries by S. K. KAWATRA. P. Eng. (Canada). Ph.D. (Australia). M.Sc. (India) (Visitor) Instruments for the measurement of lead in mineral slurries by the use of isotopes can be based on the absorption of Iow-energy gamma rays, backscattering of beta particles, or X-ray fluorescence. The merits of each method are discussed, and the reasons for the selection of the beta-backscattering technique are given. A system using this technique has been designed, constructed, and tested on samples of concentrates from an industrial concentrator.

Jan 8, 1976

By Y. R. Murthy, P. K. Satija, A. Srinivasulu, S. K. Tripathy, A. Ranjan

"In this investigation, we optimize the grinding circuit of a typical chromite beneficiation plant in India. The run-of-mine ore is reduced to a particle size of less than 1 mm in the comminution circuit and concentrated using gravity separation. The comminution circuit comprises two-stage crushing and single-stage grinding in a ball mill in closed-circuit with a highfrequency screen. A detailed circuit audit was undertaken at the plant to understand and evaluate the performance of the grinding circuit. The audit revealed abnormalities in the process and design parameters which caused high energy consumption, lower throughput, and loss of ultrafine chromite. Laboratory studies indicated the differences in the grinding properties (work index, breakage rate, etc.) and liberation sizes of these ores. Studies also revealed that grinding media size, particle retention time, and pulp density are crucial in coarse grinding. Based on the laboratory grinding and characterization studies; simulation studies were performed to optimize the operating parameters of the grinding circuit.IntroductionComminution is a critical process in mineral processing which strongly influences the economics of production. In mineral processing, particles containing valuable minerals must be disintegrated at a sufficiently fine size to liberate valuable minerals from waste constituents, so that they can be easily separated by an appropriate beneficiation method. The Sukinda chrome ore beneficiation plant utilizes different types of run-of-mine (ROM) ore with different physical properties (viz. grindability characteristics, work index, mineral composition, liberation, chemical composition, etc. for the production of chrome concentrate. In the feed preparation circuit, the ROM ore is crushed and ground to below 1 mm. Grinding in the chromite beneficiation plant is a critical unit operation to achieve the desired product size of below 1 mm and to control the generation of the ultrafine particles. Furthermore, about 40% of total power consumption in the beneficiation plant is accounted for by the grinding of the ore. This implies that any improvement of the circuit performance will lead to an overall increase in productivity."

Jan 1, 2017

By A. J. Feltenstein

A theoretical model for prediction of dissolved gold loss from a rotary vacuum filter was developed as part of a program to implement optimizing control on gold plants The filter was modelled using a modification of the Hagen-Poiseuille equation and the Choudhury and Dahlstrom washing equation. The model has three parameters which must be determined from accumulated data before predictions can be made. These are the cake and cloth resistances and the filter washing efficiency. The model predicts with a fair degree of accuracy the response of the filter to changes in the independent variables and will therefore be a useful tool in the plant optimization study.

Jan 1, 1987

By M. Rudman, L. Pullum, L. J. W. Graham

Centrifugal pumps are the workhorse of hydraulic conveying systems but their performance is derated when viscous non-Newtonian fluids, such as pastes and/or coarse solids are present. The reduced performance for purely viscous Newtonian fluids may be calculated using techniques such as the Hydraulic Institute method, but similar deration for non-Newtonian fluids is not so easy to apply. As part of the AMIRA P599 project investigating high concentration suspension pumping, centrifugal pump tests were systematically conducted on a wide range of non-Newtonian coarse particle suspensions. Suspension sup to 38% v/v of coarse particles with mean diameters in the range of 1.1 < d50< 3.4 mm suspended in carrier fluids with dynamic yield stresses of 0 < t?< 17.2 Pa and shear thinning indices in the range 0.35 < n< 0.79 were examined. Techniques such as the Hydraulic Institute de-ration method require a characteristic shear rate to be assigned before application with a non-Newtonian fluid, and a method based on pump geometry, fluid rheology and flow rate is proposed. This method predicts the dramatic characteristic reduction in head at low flow rates that is often observed and explains why larger pumps are relatively insensitive to this form of head deration. Head deration due to the presence of coarse particles in non-Newtonian carrier fluids is seen to follow similar trends to that of Newtonian suspensions and often dominates the total deration procedure.

Jan 1, 2007

By G. J. G. Juby

The Chamber of Mines Research Organization has been evaluating three membrane-desalination processes for use within the South African mining industry. These processes are electrodialysis reversal (EDR), tubular reverse osmosis (IRO), and slurry precipitation and recycle reverse osmosis (SPARRO). The evaluation of EDR and TRO is complete, and the operating costs (1988) associated with each process are expected to be about 50 cents per kilolitre for a plant of 50 l/s (4 Ml/d) installed capacity. The SPARRO process is still being evaluated. Pilot plant results, water Qualities, and expected capital costs are presented where appropriate.

Jan 1, 1992

By M. Berjak, D. M. Hawkins, V. E. Marting, R. B. MacGillivray

Contributions to discussion V. E. Marting (Associate Member): The authors of this paper should be congratulated in having pioneered the application of the Sharapov predictor to local data, and in having made a valuable contribution to South African experience in the quantitative treatment of geological information using a digital computer. Although the existing set of three programmes has been described as a &apos;suite&apos; it does not represent an integrated system in the accepted sense since the communication between runs is made in the form of punched card files to enable the mining engineer to exercise discretion and control over the data entered at each phase. Although the authors are justifiably proud of the successful results obtained through the application of this method, I feel that it is my duty to comment that the computer aspect of the work has not reached full development and is deserving of the financial support needed to increase its widest usefulness. At the present moment a routine to detect &apos;missing information&apos; has not been commissioned. Due to the lack of documentation the use of the programmes is restricted since the format for the submission of data is known only to the authors. It is very unlikely that a profitable return on the development costs will be enjoyed before the programme is fully documented and made available to wider use. My criticism of the present incomplete state of the work is being voiced purely with the intent of focussing on the significance of this project and the fact that it is deserving of development on an industry basis. It should be noted that at the economical cost of R4.00 per sq ft of computer print-out, a mining engineer can hardly afford to miss the opportunity of using the programmes on other (e.g. metalliferous) mineral deposits of tabular formation. Since the publication of this paper I have had an opportunity to see the results of the programmes developed by Drs M. D. G. Salamon and F. Deist for designing bord and pillar workings. The basic data for these latter programmes are extracted from iso-line plans drawn conventionally by geologists, a task that could be considerably expedited through the use of Mr Hawkins&apos; programmes. It appears that the efforts of these respective teams are complementary and it is in the interests of the industry that these individual components should eventually form part of an integrated system. E. Margo* (Member): This paper is a good example of how and where the backroom scientist-in this case the mathematical statistician-can aid the mining engineer to develop not only more accurate means for dealing with valuation problems but to develop a tool that can also cope with changed geological specifications.

Jan 1, 1969

By S. Pathak, B. Nilsen

Abstract: In recent years, probabilistic approach with the calculation of probability of failure instead of a factor of safety against failure is emerging in practice. The main objective of the paper is to discuss a probabilistic approach in rock slope stability analysis for Himalayan conditions. Due to the fragile geology brought about by the tectonic movements along the hill slopes, dramatic variations of the topography and intensive surface runoff during every monsoon season, serious slope failures occur frequently in Himalayan region. Slope failures have also been triggered by seismic activities. The probabilistic approach is applied to stability analysis for a road cut along the Desander back slope of the Kali Gandaki hydropower project in Nepal. It is concluded that the probability approach offers a more accurate grasp of the actual condition than any factor of safety. Zusammenfassung: In den letzten Jahren ist es mehr gewöhnlich geworden, ein stochastisches Verfahren und eine Berechnung von der Wahrscheinlichkeit eines Zusammenbruchs statt einer Berechnung von Sicherheitsfaktoren zu verwenden. Das Hauptziel dieses Artikels ist das stochastische Verfahren in Stabilitätsanalyse von Gebirghängen, welches an Himalayische Verhältnisse angewandt worden ist, zu diskutieren. Wegen der spröden Geologie die durch tektonische Bewegungen entstanden ist und den dramatischen topographischen Variationen sowie viel Oberflächenwasser während des Monsuns, kommen in der Region des Himalayas oft mehrere erhebliche Abhangszusammenbrüche vor. Abhangszusammenbruche ist auch von seismische Aktivität ausgelöst worden. Das stochastisches Verfahren ist auch benutzt worden, um die Stabilität von einem Wegschnitt in dem Desander Gebiet von dem Kali Gandaki Wasserwerk-Projekt zu analysieren. Die schlussfolgerung ist, dass die Ergebnisse eines stochastisches Verfahren die wirkliche Verhältnisse eines Abhangs besser beschreibt als der Sicherheitsfaktor. Résumé:- Ces dernières années, une approche probabiliste basée sur le calcul d’une probabilité de cassure au lieu d’un facteur de sécurité préventif d’une cassure est de plus en plus utilisée. L’objectif principal de ce papier est de discuter une approche probabiliste de la stabilité de versants rocheux en himalaya. Due à la fragile géologie causée par les mouvements tectoniques sur les versants de collines, aux dramatiques variations de topographie, ainsi qu’au lessivage intense du relief à chaque mousson, de sérieux glissements de terrains se produisent fréquemment en Himalaya. Les glissements de terrain sont aussi déclenchés par l’activité sismique. Cette approche probabiliste est appliquée aux analyses de stabilité d’une section de route le long du versant arrière Desander du projet « hydropower » du Kali Gandaki au Népal. On en conclut que l’approche probabiliste offre une estimation plus précise des conditions actuelles que n’importe quel facteur de sécurité.

Jan 1, 2003

By K. Hodgson, J. P. M. Hojem, N. G. W. Cook

Already about one-third of South Africa&apos;s coal is mined at depths exceeding 100 metres. Almost all this mining is done by the bord and pillar method. Conventional design procedures call for ever larger pillars as depths of workings increase, resulting in the loss of large amounts of coal and reductions in productivity. Barrier pillars are in general use to ensure against large collapses. The presence of these strong pillars would allow a more efficient design of the bord and pillar layout to yield improved extraction ratios by using smaller, yielding, pillars between the bords. Knowledge of the complete load- displacement curves for such pillars is a prerequisite for the design of such a system. A 100-MN, stiff jacking system for measuring the complete load-displacement curves of pillars with cross-sections of up to 2 m X 2 m is described. The jacks are installed in a slot cut across the central plane of symmetry of a pillar, thereby ensuring that the stress distribution in the pillar during a test, especially at its contacts with the roof and floor, is identical to that caused in a similar pillar by convergence across the seam. Preliminary results in the form of complete load-displacement curves for test pillars of about 1.5 metre square section are given.

By R. P. King

The flotation behaviour of phoscorite from the Phosphate Development Corporation was measured in a pilot plant, the flotation cells in the plant being varied in configuration so as to operate with or without circulating loads. The ore was floated in a batch cell so that the parameters for a kinetic model could be estimated, and these parameters were then used in a flotation-plant simulator, which is based on the kinetic model, in the prediction of the performance of a pilot flotation plant operating on phoscorite. The simulator predictions compare well with the measured performance of the ore in the pilot plant, but the comparison shows that the kinetic model is not completely adequate for the prediction of performance in continuous flotation plants. The model is weakest in its ability to model the behaviour of the froth phase. The flotation behaviour of the ore could be adequately described when it was assumed that the apatite and gangue each consist of floatable and unfloatable components. The effect of particle size on the specific flotation-rate constant of apatite was found to have a maximum at 85 µm and to fall to zero at 400 µm that for the gangue had a maximum at 50 µm and was zero at 350 µm.

Jan 1, 1978

By P. J. Nel, A. Täuber

SYNOPSIS A method is described whereby finely ground glassy granulated blastfurnace slag mixed with small quantities of clay, whiting and quartz has been used for making ceramic tiles in the laboratory. The tiles were semi-dry pressed and devitrification as well as sintering occurred during firing. The properties of the resulting product compared favourably in many respects with ordinary ceramic flooring materials.

By I. M. Macleod

An adaptive steady-state on-line optimizing regulator is proposed as an integrated approach to the control of autogenous run-of-mine milling circuits. This optimizing regulator continuously estimates an internal model of the controlled process, and, based on this, determines mill fresh solids feed rate, mill water flow rate and sump water addition flow rate such that a circuit performance objective is optimized. The dual -requirement of controlling both the mill pulp load and the load of particles of grinding media size is thus directly and simultaneously addressed. The concept and theory underlying the operation of the adaptive optimizing regulator are discussed.

Jan 1, 1987

By A. Ward, A. Smith, D. Harpley

Methods for the prediction of seepage quality from waste-disposal facilities are evaluated for input to the design of desalination treatment facilities. This is done by reference to a waste dump seeping into a near-surface aquifer, the contaminated seepage being collected by scavenger wells. As the quality of contaminated water intercepted by the wells will vary with both space and time, it is necessary for predictive methods to accommodate such variations. One-dimensional and two-dimensional predictive solute transport models are described and applied to the seepage and scavenger-well example mentioned above. The advantages and disadvantages, interims of overall applicability, data requirements, and possible accuracy, are described and discussed. While one-dimensional models have the advantages of speed, simplicity, and cost, the frequent requirement of prediction in both space and time necessitates more complex, two-dimensional simulation.

Jan 1, 1987

By I. E. Lane

Conventional demand management techniques invariably fail to offer optimum control flexibility in an operationally complex gold mining environment. An improved control system for electrical demand management is proposed. The system is designed to provide more effective load scheduling and control strategies by means of a computer aided demand management system (CADMS). The objective of the CADMS is to provide a responsive computational aid and adaptive control system for effective demand management. The system consists of a short term load forecasting module, an interactive load scheduling module, an incentive based electricity cost allocation module and a power management information module.

Jan 1, 1987