Search Documents

By M. J. Nicol, P. D. Scott

The kinetics of the non-oxidative dissolution in acids ofthe iron sulphides FeS, Fe-FeS, and Fe9S10 were studied by the use of rotating-disc electrodes of the various compounds. It was found that the rates of dissolution vary by orders of magnitude with changes in surface potential. The dissolution rates depend on non-integral orders of hydrogen-ion concentration, which in turn vary with potential. A mechanism based on the following premises is proposed to explain the kinetics of dissolution of the iron sulphides. (I) Only an FeS compound that is exactly stoichiometric dissolves in accordance with the accepted theory of ionic charge transfer. (2) Any non-stoichiometric iron-deficient iron sulphides must be reduced to exactly stoichiometric FeS before spontaneous non-oxidative dissolution can occur. The dissolution of Fe.S1o and slightly iron-deficient FeS compounds under open-circuit conditions occurs only when an oxidation reaction (usually the oxidation of hydrogen sulphide to elemental sulphur) can provide the electrons necessary for the production of exactly stoichiometric FeS. The establishment of such a mixed-potential system is the reason for the induction period that occurs during the dissolution of pyrrhotites in acids.

Jan 1, 1979

By N. Mulaudzi

The use of SO2/air gas mixtures as an oxidant to precipitate Mn from Co(II) leach liquors was investigated. The effects of SO2/air ratio, pH and temperature on Mn precipitation were evaluated. It was found that the use of SO2/air gas mixtures resulted in significantly higher Mn precipitation kinetics compared to using air or pure O2 alone. The SO2/air ratio was varied from 0% to 6% SO2(v/v) in air and similar Mn removals were achieved at 0.75% to 3% SO2 at pH 3. The solution pH was varied from pH 2 to pH 4; Mn precipitation did not increase considerably from pH 2 to pH 3, but increased significantly at pH values higher than pH 3. Cobalt co-precipitation also increased as pH increased, with 1% Co co-precipitation at pH 3. An increase in temperature from 30°C to 60°C also increased Mn precipitation and 100% Mn precipitated at 50°C. Cobalt co-precipitation also increased significantly with an increase in temperature. An activation energy of 25 kJ/mol was calculated from the Arrhenius plot, which is an indication that the precipitation reactions were both chemically and diffusion controlled. XRD analysis showed that Mn precipitated in the form of Mn2O3 instead of MnO2 that was predicted from thermodynamic data. SEM and XRD analysis also revealed that the precipitate consisted mainly of gypsum or bassanite (99%), with the Mn containing phase (< 1%) distributed within the gypsum phase. The co-precipitated Co reported to the Mn phase. Keywords: manganese precipitation; SO2/O2 gas mixtures; cobalt solutions.

Jan 1, 2009

By S. A. Lorentz, Y. Xu, C. Theron

The failure of tailings storage facilities (TSFs) results in the discharge of significant quantities of hazardous waste material into the natural environment. Research studies relating to slope instability have identified physical mechanisms such as rainfall-induced erosion, liquefaction, and shear failure as the main triggers. The generation of transient pressure waves and the mobilization of pre-event water in the unsaturated zone have been found to trigger shallow landslides in natural hillslopes. In this paper we review these physical mechanisms, known as groundwater ridging (GWR) and the Lisse effect (LE), from other studies. Previous researchers have explained both these phenomena through field and laboratory observations, numerical modelling, as well as conceptual discussions. These case studies demonstrate the impact of rainfall characteristics on the generation of transient pressure waves that rapidly increase the phreatic surface and change pore water suction. Reference is also made to the influence and behaviour of physical porous medium characteristics on the establishment of a continuous water phase that facilitates the transmission of an induced pressure head. However, previous studies fail to recognize the possibility that the pressure increase in pre-event water through pore air propagation could cause slope instability in tailings dams. The authors suggest that the physical properties and hydraulic behaviour of unsaturated porous tailings media make it susceptible to GWR and the LE, resulting in the creation of a potential failure plane.

Feb 2, 2022

A large body of work exists discussing the impact of grinding media on mineral flotation. Generally, the work indicates that a change to a less electrochemically active grinding environment has positive benefits on downstream processing. There is a fear, however, that these benefits may not be realized when treating low sulphide containing ores, typified by UG2 style deposits. A series of experiments was developed to test the flotation response of UG2 ores using the Magotteaux Mill® to determine if measurable differences in the pulp chemistry could be discerned using a range of grinding media types. Further, the flotation responses of the contained sulphides (chalcopyrite, pentlandite and pyrrhotite) were determined. The data collected provided strong evidence that the grinding environment can significantly influence the pulp chemistry and flotation characteristics of all sulphide minerals, even when the ore contains less than 0.5 per cent total sulphide. The results show that the change to an inert media type produced a substantial improvement in the flotation rate of all sulphide minerals, as well as the PGMs.

Jan 1, 2009

It is well understood that to develop wagon wheels with higher abrasion resistance, fracture toughness, and fatigue resistance, steels with lower amounts of inclusions need to be used. Clean steels are produced with technologies that minimize the amount of inclusions in the microstructure. The demand for cleaner steels is high, and lowering of non-metallic oxide inclusions and controlling their morphology, composition, and size distribution is vital. Reduction of residual impurity elements such as sulphur, phosphorus, hydrogen, nitrogen, and trace elements is essential in the production of cleaner steel. Material cleanliness is vital for fatigue endurance, since oxide inclusions may act as stress concentrators and initiation points for fatigue cracks. To better understand the relationship between the cleanliness and toughness of the 34-inch cast wagon wheels, two samples of different levels of cleanliness were supplied for investigation. This paper presents the results of metallurgical analysis using scanning electron microscopy(SEM), energy-dispersive spectrometry (EDS), and mechanical tests for the pearlitic high-performance cast rail wagon wheel (identified as Class B) that are currently being used. The Charpy V-notch impact test results for the three samples from wagon wheels were compared. With the aid of SEM/EDS analysis system, non-metallic inclusions in these steels were detected, and it was possible to determine the position, size, shape, and composition of each particle. Alumina and manganese sulphide inclusions could be identified as the dominant inclusion types in the investigated samples. Fracture surface analysis of the Charpy specimen with high inclusions indicated that transgranular cleavage was the predominant fracture mode. Fractography of fracture surfaces of Charpy impact test samples also showed improvement of toughness properties on the clean sample.

Jan 1, 2013

By M. Dobbins

Magnetic separation has long been used to upgrade and beneficiate a wide variety of industrial minerals. Advances in both wet and dry magnetic separators over the years has broadened their use, and questions are often raised about which separation technique or equipment type is most appropriate for a particular operation. This paper will provide a brief look at existing magnetic separation technologies, and discuss their potential advantages and disadvantages when applied to heavy mineral applications. Relevant case studies for the separation of ilmenite and chromite are then presented. The process development efforts undertaken for each case are described, and the rationale for selecting appropriate magnetic separation technology is explained. The nature of the material being treated must clearly be understood, knowledge and access to testing the best separation technologies is required, and careful process development and economic evaluations are a must. As is shown in the case study discussions, it is imperative that these principles drive the separation technology selection and placement, rather than looking at typical or existing similar flowsheets as rules. As examples, the ilmenite tailings case study presented in this paper shows how advances in technology have allowed for increased recovery of -45 µm ilmenite by utilizing a multi-stage SLon® wet magnetic separator circuit equating to an additional 30 000 tons of ilmenite produced per year. The virgin chromite case study presented shows that through careful testing and circuit design efforts using RED technology, a 20% increase in overall chromite recovery was achieved over previous demonstration work.

Jan 1, 2007

Good blasting practices based on the careful application of explosive energy lead to significantly safer mining operations. Case studies demonstrate how the selection of the correct charge mass, explosive type and round design are vital for extracting the exact amount of rock required and preventing spurious damage to the remaining rock mass. In other cases the explosives are applied to precondition the rock mass, design rockburst resistant support, prevent damage to important excavations and reduce the exposure of miners to unsafe conditions. The Hybrid Stress Blasting Model is used to understand the explosive rock interaction and to illustrate and contrast good and bad blasting practices. In all cases, good supervision is required to continue safe mining according to the design. Keywords Blasting, safety, production, preconditioning, explosives, numerical modelling, drop raising, vibrations, and presplitting.

Jan 1, 2011

By S. A. Abdel Sabour

Strategic decisions in the mining industry are made under multiple technical and market uncertainties. Therefore, to reach the best possible decision, based on information available, it is necessary to integrate uncertainty about the input variables and model financial risk of the project?s merit measures. However, this provides few useful insights to decision-makers unless accompanied by modelling management responses to uncertainty resolutions. It is widely acknowledged that conventional decision-support methods based on static, no-change, discounted cash flow (DCF) techniques such as net present value (NPV) and internal rate of return (IRR) tend to provide inaccurate value estimates. This could mislead the strategic decision-making process and result in significant value losses. This paper aims to model financial risk related to uncertainty about market variables such as metal prices and foreign exchange rates. Other sources of risk that are related, for example, to geology and production costs are not considered in this work. The article outlines a flexible financial model that integrates uncertainty about market variables and management flexibility to react to uncertainty resolutions into mine project valuation using a real-options valuation technique based on Monte Carlo simulation. Significance of information generated from this simulation-based flexible valuation model to the strategic decision-making process is tested using an illustrative case study of a Canadian mining project. The project is a typical multi-metal, open pit mine that produces copper and gold. In this case, there are three uncertain market variables, which are: copper and gold prices and US$/CAN$ exchange rate. Financial valuations are carried out using both the conventional static DCF method and a flexible real-options model. In the flexible model, management flexibility to decide whether to go ahead with the next expansion or terminate production operations is integrated. Results show how the flexible financial model can enhance the decision-making process.

Jan 1, 2009

By J. Danoczi

South Africa is running out of fresh water and is looking at ways to improve water usage. This report addresses how a diamond mine in Gauteng has improved the utilization of its water resources. In the past, water from the local river was deemed the most suitable to use in the grease recovery plant but subsequent tests on the water from the slimes dam have shows that this water source is in fact more suitable for diamond recovery. Utilizing the slimes dam water provides a more stable water source than the local river while also reducing the impact of the mine on the water resources in the area.

Jan 1, 2008

By D. G. Millenbruch

An account is given of a four-phase system for the appraisal of a mineral project while it is still in the exploration stage, and for continual consideration of a favourable appraisal until the production stage is reached. There are ten stages from the idea of a likely project to the production stage, and all the staff that are eventually to be concerned with the development of the project are involved at an early stage.

Jan 1, 1979

Colloquium and General Meeting were held at Kelvin House on 19th May, 1971, the theme being &apos;Modern trends in coal mining practice.&apos; Mr V. C. Robinson (President) was in the Chair. The Colloquium was attended by 205 delegates and was opened by the President at 9 a.m. OBITUARY The President: &apos;It is my sad duty to announce the death of C. C. Cullen, Fellow, who joined the Institute in 1946 and passed away on 15th March, 1971. As a mark of respect to the memory of the deceased and in sympathy with the bereaved I would ask you all to rise and observe a few moments silence&apos;. ELECTION OF SCRUTINEERS The President: &apos;In terms of Clause 9.4 of the By-Laws I now call for the nomination of seven Corporate Members to act as scrutineers of the ballot for Council&apos;. Messrs V. C. Robinson, Prof D. D. Howat, Dr J P Hugo, D. G. Maxwell, J. K. E. Douglas, R. J. Adamson and P. Lambooy were nominated by P. W. J. van Rensburg and seconded by P. A. von Wietligh. The President: &apos;Are there any further nominations? If not I declare these gentlemen elected.&apos; MEMBERSHIP The President: &apos;I have much pleasure in announcing that the names of candidates, having been published in accordance with By-Law 5.2.2, Council has elected them to membership of the Institute in the following grades: Members: Douglas Edward King, Bryan Rudolph Scott, James Gregor Phimister, Anthony David Walters. Graduates: Cornelius Johann Muller, Marthinus Stephanus Mulder. Associates: John George Everson, Colin Robert Llewellyn Davies. Students: Francois George Enslin Beetge, Ewald Boshoff, Christiaan J. Cloete, Christopher John Davies, Cameron George Elvin, Kenneth Eric Field, Johannes Louis Fourie, Hans Gert Gastrow, Peter John Ledger, James Robert William Lindsay, Kynaston Lloyd McDonald, Richard Peter Mohring, Arthur Leslie Painting, Matthias Arthur Pascall, Ian Neil Sinclair, Donald Allan James Ross-Watt. MEMBERS TRANSFERRED TO A HIGHER GRADE From Member to Fellow: Peter Norman Roberts. From Associate to Graduate: Alfred Eric WaIter Fletcher. From Student to Graduate: Wilfried Pierre de Villiers, Edward Emile Eichenberger, William Alan Nairn, Lodewyk Johannes de Jager, Colin Henry Obray, John Grenig Rees. COLLOQUIUM The President opened the proceedings and introduced Mr N. W. S. Schumann as the overall chairman for the day. The following papers and contributions were presented: FIRST SESSION: Chairman R. C. J. GOODE. Paper: &apos;Problems encountered in the operation of a new colliery&apos; by P. M. C. Wilson and A. A. Oakes. Contributors: D. J. Moloney, G. R. Canny, I. G. Evans, R. B. MacGillivray, Dr F. G. J. de Jager, M. J. Deats, and N. Zolezzi. R. B. MacGillivray Mr President and gentlemen, I would like to congratulate the authors on presenting a most interesting paper on a very important subject. After several attempts at finding suitable reserves to extend the life of Welgedacht Exploration Company&apos;s Utrecht Colliery a block of coal rights was acquired south west of the town of Utrecht. A study of these reserves showed that they would enable a satisfactory return on capital invested to be achieved. It was decided therefore to open up what is now called the Zimbutu section of Welgedacht Exploration Company, to produce 41 000 metric tons of coal per month. The decision to open this section was taken in August, 1968 and due to certain allocation requirements it was necessary to bring it into production by the 1st of January, 1970. Fortunately a fair amount of statistical data had been collected prior to August, 1968 from the old Utrecht Colliery in anticipation of opening a mine and a fairly detailed rechnical report had been prepared. As a result the dead line was only missed by four days. Main features of the Design A feasibility study was carried out on three possible shaft positions and the final position was selected from these three on economic grounds. As the coal seam at the selected shaft position was only 21 metres below the surface it was decided to sink two twin incline shafts to enable rapid establishment of through ventilation and alternative hauling arrangements for quick development. This also allowed the final vertical ventilation shaft to be placed at some distance away to avoid the nuisance of fan noise. Second outlet requirements are also very well met by these twin inclines. Again on the basis of economics and also due to the uncertainty of roof conditions it was decided to use hand loading methods underground. However, to allow for future possible conversion to mechanised loading, should this become economical through rising wages, a conveyor belt was installed in the hauling shaft. This conveyor belt is fed from an endless rope haulage in the east companion by means of tipplers, a bin and a feeder. The main development heading was left clear for the future installation of a conveyor belt which would afford easy conversion to mechanisation.

Contribution by G. Narsimhan It was with much pleasure that I went through D.F. Malan&apos;s excellent paper. The following explanatory and critical note has been the result of my deep study of the paper. Although by qualifications and experience I have been a chemical engineer, involved over four decades with problems in the modeling and simulation of transport-limited (heat and mass) chemical reactions in multi-phase systems, I have of and on interested myself in challenging problems in extractive metallurgy. This is the first time I have veered of to continuum mechanics, at the age of 71! Author&apos;s reply. I thank Professor Narsimhan for his extensive contribution to the paper. It provided me with the stimulus to derive an extended model. However, there are some inaccuracies in his arguments that need further discussion. Professor Narsimhan&apos;s main concern is that there is not a good enough fit between the derived viscoelastic Kelvin model and the experimental data supplied by Güler1 (see Figure l1 on page 218 of my paper). I will therefore explain the choice of a viscoelastic model in more detail and also make specific comments on the arguments given in his contribution.

Jan 1, 1996

By B. X. Huang

Hydraulic fracturing technology is presented as a solution to improve permeability and thus solve the extraction problem of coal seam gas in low-permeability gas-bearing coal seams. Given an existing group of original cracks, the propagation of main hydraulic cracks and hydraulic wing cracks was simulated using realistic failure process analysis software. The process represents the structural transformation of hydraulic fracturing and permeability improvements caused by it. In addition, a field test for improving the permeability of gassy coal seams by hydraulic fracturing was also conducted. The propagation of the main cracks and wing cracks by hydraulic fracturing forms a network of original joint cracks, hydraulic wing cracks, and main hydraulic cracks, which improve the permeability of the coal seam. High-pressure water in the drill hole and in the main hydraulic cracks permeates the two flanks of the hole, forming the permeating water pressure. With an increase in drill water pressure and an extension of the main hydraulic cracks, the permeating water pressure on both sides of the main hydraulic cracks in the coal mass also increases. Hydraulic cracks tend to form connections through rock bridges. The extension of hydraulic wing cracks through connections in the rock bridges between the cracks transforms the rock mass to a fractured structure and improves its permeability. Hydraulic fracturing technology for improving permeability in underground conditions can increase the amount of gas drainage by a factor of 15. A stress relief area develops at a radial distance of 10-2.0 m from the hydraulic fracturing drill hole, while an area of rising stresses, called the pressurized area, develops a further 15 m away from the pressurized hole. Practice has proved the existence of the stress transfer phenomenon and the high stress area after fracturing. This kind of hydraulic fracturing technology is more effective in holes drilled from underground than in surface drill holes, with respect to costs and controllability, and is therefore the major trend in gas drainage development in coal mines.

Jan 1, 2012

By I. V. Filippova, Y. Foucaud, M. Badawi, O. Barrès, L. O. Filippov, S. Lebègue

Sodium silicate (Na2SiO3) is one of the most common reagents used in the froth flotation process, in which it is an efficient dispersant as well as a powerful gangue minerals depressant. Due to its high affinity with a lot of minerals, mostly silicates, it adsorbs on their surfaces and prevents the adsorption of the collectors, maintaining them hydrophilic. Hence, Na2SiO3 is widely used in the flotation separation of rare earth minerals, zinc minerals, iron minerals, scheelite, fluorite, apatite, and many other minerals. For decades, authors have demonstrated higher efficiency of Na2SiO3 when it is used in combination with sodium carbonate (Na2CO3), a common pH regulator. Among many well-known depressants, this system presented the best efficiency for many ores, including the Tabuaço scheelitebearing skarn studied herein. However, the mechanisms resulting in these strong positive synergistic effects are not well understood at the moment. Hence, the response surface methodology (RSM) was applied to this ore, considered as a case study, to optimize the depressing conditions and to study deeply the flotation behavior of this system. Strong synergistic effects between the two reagents were exhibited by the RSM, mostly affecting the scheelite, fluorite, and calcium-bearing silicates recoveries. This was attributed to surface carbonation of the minerals by Na2CO3, subsequently leading to a better depression by Na2SiO3. Overall, a 1:1 ratio between the two reagents displayed the best results in terms of WO3 grade and recovery. To gain understanding in the molecular mechanisms responsible for the aforementioned synergistic effects, FTIR studies were combined with state-of-the-art molecular modelling (Ab Initio Molecular Dynamics at 300 K) on fluorite, an archetype of calcium minerals. Keywords: Synergistic effects, scheelite, depressants, FTIR, DFT calculations

Jan 1, 2020

By N. B. Prenn, R. H. Robinson

"The model described is a design and economic planning tool for analyzing surface mineral deposits. Mineralization, topography, costs and significant geologic features are input to the model. The results are:(i) final pit limits yielding the maximum total profit,(ii) annual cut-off grades and plant sizing yielding the maximum present value, and(iii) annual maps of the pit and annual production statistics for the mine, concentrator and smelter.Additionally, summaries are printed of the block mining sequence and cash flow. A special feature is an option to include dump-leaching operations. Stockpiling of material can also be simulated by the model. The model is built around theories of dynamic cut-off grades and a pit design algorithm. The dynamic cut-off grades maximize present value by examination of all economic and physical constraints for the optimum combination. The pit design algorithm is a set of rules formulated to find the maximum value from a special graph. The graph is different from graphs of analytical geometry, being made up of points and arrows connecting some of the points. These graph elements describe the relationship between any point in the deposit and the material which must be mined to get at that point. The model was designed to bring together the interdependent theories of economics, pit design and production scheduling."

Jan 1, 2014

By D. Lunt

This paper describes and sets in context the commercially proven uranium extraction processes. It also discusses some of the technologies that are currently being pursued with the aim of reducing costs and overcoming a number of technical issues that are faced by process designers and operators. In doing so, opportunities for the transfer of extraction technology from other industries/commodities are identified. The key processing areas that are examined include: ?The influence of mineralogy. The type of uranium mineralization and the nature of its association within a particular deposit will have a major impact on process route selection. Uranium minerals are classified according to their influence on extractive metallurgy. As the uranium price has risen in recent times, so opportunities are increasing for the recovery of uranium from less conventional resources such as phosphates and fossil fuels. ?The opportunities for employing techniques aimed at reducing the capital and operating costs of the overall process such as heap leach and beneficiation. Preconcentration by screening, gravity separation and radiometric sorting can potentially reduce the mass flow to the downstream leach and recovery plants. ?Purification or separation of uranium in carbonate systems. While it is possible to directly precipitate uranium from clarified leachate, the presence of impurities such as vanadium, molybdenum and others may dictate that ion exchange or selective precipitation is employed. Advances have been made in other industries in terms of improved ion exchange equipment aimed at reducing resin inventories and hence costs. ?Separation in acid leach systems. Earlier developments included the use of combined SX-IX systems (Eluex or Bufflex) and the introduction of continuous countercurrention exchange (CCIX). Column SX has found a ready application to uranium in view of the rapid extraction kinetics. With the renewed interest in uranium processing, efforts are being redirected towards further development of resin-in-pulp (RIP) as a means of driving down capital and operating costs. ?Extraction in a chloride environment. Australia and Namibia are desert countries where good quality water comes at a cost. However, both have access to saline water from either the ocean or subterranean aquifers. The issues associated with operating a uranium extraction operation in such environments is discussed. ?Extraction from less conventional sources. Recent price increases for U3O8 have resulted in a number of companies examining the recovery of uranium from sources such as fossil fuels and phosphate deposits. Both of these areas were examined in the 1970s and 1980s and a number of approaches were commercialized. The paper reviews the extraction options.

Jan 1, 2007

The depletion of favourably located and higher-grade mineral deposits, combined with more favourable metal prices and higher capital costs, has stimulated research into heap leaching of lower grade ores and wastes. This has resulted in renewed interest in heap leaching of uranium ores, and in the development of processes for the bacterial heap leaching of low-grade chalcopyrite ores and the acid heap leaching of nickel laterites. A complete programme of heap leach testwork typically involves a sequence of bottle roll tests and column tests, followed by piloting on test heaps. The initial testwork is aimed at determining the amenability of the ore to heap leaching, which depends on the characteristic of the ore with respect to porosity and permeability to leach liquor, acid consumption, metal recovery and percolation. Subsequent phases of the testwork focus on the development of the process design criteria for the treatment of the ore. Basic techno-economic models have also been developed as a tool for the initial estimation of heap leach viability. Mintek has also developed in-heap monitoring probes, coupled to an operator guidance system, in order to assist the operator in achieving optimal conditions for bacterial growth and heat preservation during pilot-plant operation.

Jan 1, 2009

By Paul Fouchè

Contents ?Purpose ?Introduction ?Why manage a mineral resource ?Sampling or tracking from source ?How can RF tracking help ?Project Goals ?RF System ?Tracer Layout ?Antenna

Jan 1, 2005

Notices COMPETITION FOR STUDENT MEMBERS OF THE SOUTH AFRICAN INSTITUTE OF MINING AND METALLURGY Each year the Institute offers a prize (or prizes should the entries warrant it) of up to RlOO for the best paper or dissertation on a topic appropriate to the interests of the Institute. The competition is open to all Student Members of the Institute. APPLICATION AND PRACTICAL OPERATION OF HYDROCYCLONES Dr H. F. Trawinski of Amberger Kaolinwerke, Hirschau, West Germany, gave a very interesting lecture on this subject to an audience of over one hundred, composed largely of members of the Institute, on 15th August, 1973, at the University of the Witwatersrand. ROTARY INTERNATIONAL Applications are invited before 15th March, 1974, for the following awards of The Rotary Foundation: Post-graduate Fellowships Under-graduate Scholarships Awards for Technical Training Awards for Teachers of the Handicapped. NIM REPORTS Report No. 1509 The instrumentation developed for electrochemical studies of the le(Whing of uranium dioxide. Report No. 1550 A fundamental study of the dissolution in (Wid solutions of uranium minerals from South African ores. Report No. 1552 The preparation and analysis of minerals for use as reference material.Progress report No. 2. Report No. 1556 The spectral analysis of solutions.2. The analysis of leach liquors, concentrates, slags, and residues. Report No. 1559 A cost assessment of the production of elemental sulphur by chlorination roasting. Report No. 1562 Application of a flotation model to an industrial plant

Jan 11, 1973

The key functions of project evaluation are to assess potential profitability and to develop an effective operational design. For mining projects, design aspects include mining methodology, ore treatment methodology and production rates. All of these characteristics impact on project economics and overall value. Resource models, which form the ultimate basis of project evaluation, typically consist of tonnes above cut-off, grade above cut-off and the spatial distribution (connectivity) of tonnes/grade above cut-off, for one or more variables. Dilution, ore loss and metallurgical recovery are all modifying factors applied to the resource model during evaluation and determination of profitability. A key issue is: how is the value determined? In addition to traditional combination of in situ tonnes/grade, the following merit serious consideration: the concentration of deleterious elements, throughput rates, mining/processing costs and - importantly - metallurgical recovery. Geometallurgy is an emerging field targeted at integrating these issues by identifying either direct measures or proxies for throughput (hardness, grindability), recovery (liberation, mineral shape/texture, etc) and concentrate quality from easily collected macro-, meso- and microscopic data. These &apos;geometallurgical variables&apos; drive project costs and revenues in a fundamental way. For geometallurgical characterisation to have a real impact on business design, it must enable improved mine planning. When creating spatial estimates for such variables, it is preferable to find proxies that can be measured as close to the intact rock mass as possible. However, spatial estimation of proxies for geometallurgical properties and responses is complex and requires special consideration. Unlike grades, both proxies and absolute measures of geometallurgical variables are not necessarily linear or additive and therefore require very careful geostatistical consideration. In some cases, models must predict extreme values of geometallurgical attributes rather than averages. Incorrect characterisation of metallurgical recovery/throughput can (and has) led to misspecification of the scale of projects, and thus can be seriously value destructive. Aspects of geometallurgy have long been important in iron, bauxite, manganese and coal deposits and are increasingly on the radar for base and precious metal miners. However, as more metallurgically complex deposits are developed and mining of large-scale, low-grade deposits becomes more commonplace, the importance of characterising the metallurgical response in order to generate properly optimised projects will rapidly increase. It is possible that in many `traditional&apos; (ie grades and tonnes) reserve models, the variables that drive the project are missing!

Jan 1, 2007